Search Results

Search found 16871 results on 675 pages for 'computer vision'.

Page 218/675 | < Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >

• Wired connection not working

  - by YokoBlac

  I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

  Read the article

• dual-boot does not work

  - by elyashiv

  I have a PC with linux-mint installed on it. I wanted to install win-7 along-side, for some reasones. what I have done is: create a bootable USB-stick with Ubontu ios. restarted the computer, this time with Ubuntu (running from my disk-on-key). created a partition on the main HD using GPart. formated the partition to NTFS. restarted the computer, this time through the installation CD for win-7. installed win-7 with normal settings. that all worked, and I'm writing this through win-7. the thing is - when I boot my system, I don't get to choose what OS to run. I checked the settings in msconfig, and in boot label it has just win-7. how can I boot linux?

  Read the article

• Blank screen during boot after clean Ubuntu 11.10 install (Intel N10 graphics)

  - by Coen

  After a clean install of Ubuntu 11.10 on my Asus eee PC 1005p, Ubuntu seems to boot correctly, except for initialization of the LCD screen. What I observe: I choose Ubuntu 11.10 in the GRUB 2 menu A blank screen with a blinking cursor in the top left of the screen, for 15-20 seconds. The ubuntu logo with 5 red dots in the center of the screen, for 1 second. The LCD screen is entirely blank The startup sound plays (Ubuntu is configured to auto-login) Still, the LCD screen is entirely blank. When I press Fn-F8 (the switch between LCD screen and external VGA), the LCD screen shows my desktop correctly and everything seems to work fine. Except for the adjust contrast buttons (Fn-F5 and Fn-F6), these seem to cycle through random brightness modes. Something like: 0% - 50% - 20% - 0% - 20% - 0% Any ideas what's causing this or how to solve this? coen@elpicu:~$ lspci -v 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7e00000 (32-bit, non-prefetchable) [size=512K] I/O ports at dc00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at f7d00000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0 Memory at f7e80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied>

  Read the article

• 1080p HD TV + what is minimum spec pc required to stream HD movie files to it?

  - by rutherford

  I want to stream hi-def (non flash-based) movies from my future minimum spec pc to my network-ready HDTV. What I want to know is a) when streaming from a computer (local wifi network), is the computer's cpu/video/ram resources used to the same extent as it would be if playing back on the computers local screen? If not what are the differences? b) So with streaming hd content what is the minimum spec processor I should go for, if i) only one TV is acting as client ii) two TVs are simultaneous clients.

  Read the article

• How do spambots work?

  - by rlb.usa

  I have a forum that's getting hit a lot by forum spambots, and of course the best way to defeat something is to know thy enemy. I'll worry about defeating those spambots later, but right now I'd like to know more about them. Reading around, I felt surprised about the lack of thorough information on the subject (or perhaps my ineptness to input the correct search terms for better google results). I'm interested in learning all about spambots. I've asked on other forums and gotten brush-off answers like "Spambots are always users registering on your site." How do forum spambots work? How do they find the 'new user registration' page? (I'm especially surprised because some forums don't have a dedicated URL for this eg, www.forum.com/register.html , but instead use query strings or even other methods invisible to the URL bar) How do they know what to enter into each 'new user registration' field? How do they determine what's a page they can spam / enter data into and what is not? Do they even 'view' this page at all? ..If not, then I'd assume they're communicating with the server directly - how is - this possible? How do they do it? Can forum spambots break CAPTCHAs? Can they solve logic questions (how?)? Math questions? Do they reverse-engineer client-side anti-bot validation scripts? Server-side scripts? What techniques are still valid to prevent them? Where do spambots come from? Is someone sitting behind the computer snickering as they watch their bot destroy site after site? Or are they snickering as they simply 'release' it onto the internet somehow? Are spambots 'run' by an infected computer somewhere? Do they replicate themselves? etc

  Read the article

• "TMGR is Missing" after repair-installing Windows XP

  - by djzmo

  I have two OSes installed in my computer. - Windows XP Professional - Windows 7 Ultimate (Release Candidate 1/Build 7100) I used the Windows 7 boot loader by default to choose between OSes. When I was using my WinXP, my computer gets lagged suddenly and continuously, and the only way to fix it is by repair-installing it (because I've experienced this many times before, but without W7 installed). Everything goes OK. But when my XP was successfully reinstalled, I cannot boot my Windows 7 anymore. Every time I tried to boot the harddisk that contains W7, an error appeared. "TMGR is Missing". Now I have no idea how can I get back to my Windows 7. Any kind of help would be appreciated! :)

  Read the article

• RAID 5 heavy IO hard freezes Ubuntu: Why?

  - by Luke has no name

  I have a software RAID 5 partition on LVM in Ubuntu (desktop, actually, but I'm using it as a server). I have been rsyncing a ton of data to it, and the computer was hard freezing, as in I needed to press "Reset". So I thought it was rsync. But I decided I'd try a dd if=/dev/zero of=/path/to/raid5 and sure enough, the computer locked up. Did an identical dd to a JBOD partition on the same machine, and it didn't crash. Assuming a clean RAID5 partition, tri-core processor 2GB of ram, 6GB swap, what could be causing this?

  Read the article

• RCA monitor won't display highest resolution when NVidia drivers are installed

  - by novellterminator

  My computer is a dual-monitor setup. It won't display my second monitor's highest res... In fact, it will only display one resolution. Anything higher or lower makes the monitor not show the screen. I've had this problem with this computer, and I upgraded almost all my components (cpu, RAM, mobo, and video card included) and I still have this problem with my new setup. This leads me to believe it's a problem with my monitor and the NVidia driver together. Any thoughts on what can be done? The manufacturer of the monitor doesn't make a driver for this monitor. I used to run Windows Vista and now my new setup runs Windows 7.

  Read the article

• Is it possible to boot from internet?

  - by Calmarius

  Let's assume the following situation: you have a computer with empty hard disk, and you don't have a CD, floppy, pen drive nearby to boot the computer from. But you have connection to the Internet. Modern computers support network booting using PXE, but I haven't found anything regarding booting via the internet. So, is it possible to use PXE to load an image from the internet and boot it? By having a running system (even a minimal Linux) in RAM, it should be possible to install it on the hard disk, and build up a working system from here.

  Read the article

• Windows 7 stopped booting

  - by jstawski

  I have a laptop which after shutdown it stopped booting. I tried repair, safe mode, and even start with Windows 7 Installation. The screen just goes blank with a mouse pointer that I can move around. I removed the harddrive from the laptop and connected it to my desktop using an External HD casing. The computer recognizes the disk, but it seems like it can't read it. If I go to My Computer it shows up, but it doesn't display usage information. When I double click on the drive it sits there as if it was loading something and eventually shows "G:\ is not accessible. The parameter is incorrect." Disk Management and Diskpart also take forever to load and when it does it shows the drive. My question, do you think this is a hardware problem or some corrupted sector? How can I try to fix the drive without formatting it? Thanks...

  Read the article

• Sync outlook between two computers?

  - by Cortopasta

  Is it possible to sync calendar/email/contacts between my work computer and my laptop?

  Read the article

• Having trouble installing Bradcom STA driver

  - by user192881

  I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

  Read the article

• external usb hard drive is not being seen anymore

  - by incrediblehulk

  I think my problem is a little different than several other similar titled questions. Everything started while I was using 10.10. External drive was always recognized and mounted, but the timing of this differed. I mean when I booted, the OS sometimes saw the drive immediately, sometimes after a few minutes, sometimes after hours. Although this was annoying, I tolerated this somehow. Then this problem persisted after I upgraded to 11.04 with a clean install. Afterwards, the drive became totally invisible to the OS. It is not even detected as an usb device anymore. However, there is one thing I can do to make it seen. If I boot to another operating system which can detect the drive, and then boot back to ubuntu, everything is perfect. but this is of course very impractical. To summarize, the usb drive is recognized by ubuntu if and only if another OS in the same computer could recognize it first. I should also say I have not had any problems with the same drive in any other OS or a different computer. My drive is philips with a hitachi hdd inside, has its own power source and any other usb powered drives have never caused this kind of a problem. I've tried almost all recommendations in similar topics but none of them seems to be related to this one. What can I possibly do to fix this?

  Read the article

• Shutdown button doesn't work in Windows 8

  - by Yob

  Some time ago I installed Windows 8 64bit ready-to-market version (as a student I had access to it before premiere). What I discovered is that the "shutdown" button doesn't work. When I want to shutdown the computer it simply logs me out. In order to turn off my machine I have to click "restart" and then simply press the poweroff button. I installed some updates but this issue is still not resolved. Is there any way to shutdown the computer in a normal way?

  Read the article

• How to fix Asus Eee PC 900 startup issues after failure?

  - by EBrown

  My Asus Eee PC 900 shows no signs of life. I push the power button and get no response from anything. No lights, no power, no boot-up screen. It has been like this since I received it from a friend. I asked her what happened and she said that smoke came from the keyboard, it shut down and hasnt turned on since. I have tried removing and cleaning the RAM, the computer charger still connects and works, but the battery receives no charge and the computer won't power on. Any ideas as to what is going on?

  Read the article

• Windows 7 fresh install blank screen

  - by Neil Barnwell

  I've just installed Win7 Ultimate to my PC. During the install it reboots a couple of times, but 2nd or 3rd reboot I see the "Starting Windows..." message, but followed by a black screen. No mouse cursor, taskbar, anything. The monitor power light is blue (indicating it has a signal) and it was displaying the setup wizard with no problems whatsoever. Has anyone else witnessed this phenomenon? Many thanks in advance. UPDATE I booted in safe mode, and got a screen saying "Setup is preparing your computer for first use". That's brilliant, although a message box has popped up over that saying: Windows cannot complete instlalation in Safe Mode. To continue installing Windows, restart the computer. So I don't really have the opportunity to do any cleverness with drivers or anything. I guess I could try getting a different version of Win7 (I'm installing from an MSDN DVD).

  Read the article

• Does the size of the monitor Matter?

  - by Arsheep

  I have a old computer, and I want to buy a big LCD. The best I've found so far is Viewsonic's 24" LCD TFT monitor. So will it run without any problems, or do I need to upgrade the video cards or something as well? The computer is not too old: it has P4 board and celeron processor, with 128 graphics memory. And in display properties, it says that the maxium that I can use is 1280 x 1024 resolution. I am noob hardware-wise, so need help on this stuff. Thanks

  Read the article

• Does the size of the monitor Matter?

  - by Arsheep

  I have a old computer, and I want to buy a big LCD. The best I've found so far is Viewsonic's 24" LCD TFT monitor. So will it run without any problems, or do I need to upgrade the video cards or something as well? The computer is not too old: it has P4 board and celeron processor, with 128 graphics memory. And in display properties, it says that the maxium that I can use is 1280 x 1024 resolution. I am noob hardware-wise, so need help on this stuff. Thanks

  Read the article

• Does the size of the monitor Matter?

  - by Arsheep

  I have a old computer, and I want to buy a big LCD. The best I've found so far is Viewsonic's 24" LCD TFT monitor. So will it run without any problems, or do I need to upgrade the video cards or something as well? The computer is not too old: it has P4 board and celeron processor, with 128 graphics memory. And in display properties, it says that the maxium that I can use is 1280 x 1024 resolution. I am noob hardware-wise, so need help on this stuff. Thanks

  Read the article

• Wi-Fi or Bluetooth to USB converter

  - by yerzhik

  Is there a device, that works without a driver, you just connect it as usb, and receive any signal sent to it as if it were COM Port wired connection? For example, such a device that gets data sent to it by Wi-Fi network or Bluetooth and resends it to the USB. Of course it has to be set up once (network name, password etc) and for this purpose you need a driver, but once it is set up, you can use it at any computer without a driver. I have a Bluetooth USB, but I think it can't work without a driver. By just connecting it to any computer you can't find it in device list on another bluetooth device (as phone, etc).

  Read the article

• How do I force the system to look for new sound devices?

  - by John Zeringue

  I have a small flat screen TV (Toshiba) that I often connect via HDMI to my laptop (an HP Pavilion dv4) and use as a computer monitor. When I do this, I prefer to use the TV's speakers, particularly when I'm watching video, because the sound quality is much better. However, when I connect the HDMI cable after turning on my computer (rather than having it plugged in before booting up), Sound Settings does not list the TV as an output device, and I am forced to reboot. I was curious if there is an easier solution to this, perhaps a CLI command to check for new sound outputs. Does anyone know of something like this or have another solution? To clarify, I believe this is a software problem. The HDMI always works, and I can switch my desktop over to the TV at any time. The issue is that, if the HDMI wasn't connected during start up, the TV will not appear as an output option in the Sound Settings GUI. So, unless I'm mistaken, my question is not HDMI specific, but rather a general usage question about manipulating sound settings from the command line.

  Read the article

• Using git with cgit for decentralized/centralized development

  - by polemon

  I plan to use git for hosting my projects on my server. I've read about cgit, git-daemon, and I more or less decided to use those tools. But general use is still kind of confusing for me. What do I need to set up on the server, to push my files onto it. And when the files on the server are newer as the files on my computer, how do I merge them? Also, I use, say, two computers where I develop. How do I merge from one computer to the other? Also, when two people are working on the same project, how do they merge their local repos from one another? As you probably can tell by now, I come from SVN, but I've worked with Mercurial and now I'd like to test git.

  Read the article

• Hard drive clicking noise on Acer AO722

  - by Blank

  I'm running Ubuntu 11.10 on an Acer Aspire One 722. Whenever I'm on battery power I get a clicking sound from my hard drive every 5 seconds or so (this does not happen when the laptop is plugged in). I'm dual booting with Windows 7 and I don't get the clicking sound in Windows. The clicking sound stops when I run the command:sudo hdparm -B 254 /dev/sda Also, according to:sudo smartctl -H /dev/sda my hard drive is healthy. Is this clicking sound something I can just ignore? Or is it a serious problem and will it eventually damage my computer? If so, how would I fix it? I have tried adding hdparm -B 254 /dev/sda to my /etc/rc.local file, but I still run into the clicking problem if my computer boots while plugged in and is then unplugged. Also, I'm finding this fix to be unreliable. Sometimes it works, sometimes it does not. Is this a good solution and is there a better way of doing this? Also, would running my laptop with a -B value of 254 have any negative effects? (I read somewhere about a lower level protecting the hard drive from bumps)

  Read the article

• Why aren't there 8gb RAM modules yet?

  - by user49951

  Why is RAM module development seemingly stuck at the same size for a while now (a couple of years)? I bought 2x2gb modules 2 years ago, and now it's all the same size, with prices even bigger. I want more memory, because I work a lot on my computer and I just need it. What is going on? Hardware/memory progress was being made constantly until these couple of years, and I'm a big computer user for over 15 years. Why isn't here 4gb/8gb modules yet? I would gladly replace my DDR2 motherboard for a DDRX one if it had at least 4gb DDRX modules for a reasonable price. Now we have a situation with very cheap usb drives reaching 64gb size, and a ram modules with pathetic 2gb size. Sounds like some sort of conspiracy.

  Read the article

• Java Applets fail to launch in Windows 7 64bit

  - by Steve

  Hi can you help? I'm having great trouble launching Java applets using Windows 7 64 bit. I have the 32 bit version of Java installed (as recommended, for use with 32 bit browsers). When I click on an Java applet to open it the Java logo shows with a circular progress bar, but the process goes no further, just the progress bar going round and round. There are no error messages. The computer is a few months old and Java has never worked properly. I've tried with both IE9 and Chrome, followed the suggested fixes, uninstall then reinstall, check certain browser settings (all were in order), check Java control panel settings (again all was in order) delete the internet cache etc, tried 32bit & 64bit Java side by side. All to no avail. I'm baffled Is there anything else to try, or do I have to accept a computer without Java (Very inconvenient!) Thanks

  Read the article

< Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >