Search Results

Search found 21277 results on 852 pages for 'cursor current'.

Page 218/852 | < Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >

  • Increasing Screen Resolution to more than limit and scaling to origional

    - by Akshat Mittal
    I have a laptop, with Screen Resolution - 1366x768 (most common) - I want to increase it further to 1600x900 (or higher), in the same ratio. I want to scale the higher resolution on my current screen to fit it. I found xrandr with command xrandr --output LVDS1 --scale 1.4x1.4, this worked but again resulted to another problem, it does the scaling thing but the cursor is still blocked into the native screen resolution and I am not able to move it further, I found that the bug is already filed here. Also this command was only for Linux, I wanted to do this thing with both Linux and Windows (including Windows 8). I want a similar software that is bug free (at least not a major bug like this) and that supports Windows as well (or two separate software for Windows and Linux). Any help is appreciated and Thanks in advance.

    Read the article

  • Help about pure-ftp

    - by hai
    I setup pure-ftp on freebsd behind firewall. On pure-ftp setuped passsi mode ftp(rangle port 50400-50600) and firewall open port from 50400-50600 (include mode IN and out). But i try use ftp client connect but not connect. Nofinication error status: Connecting to 210.245.89.95:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 13:20. Server port: 21. Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER bk Response: 331 User bk OK. Password required Command: PASS Response: 230 OK. Current directory is / Command: SYST Response: 215 UNIX Type: L8 Command: FEAT Response: 211-Extensions supported: Response: EPRT Response: IDLE Response: MDTM Response: SIZE Response: REST STREAM Response: MLST type;size*;sizd*;modify*;UNIX.mode*;UNIX.uid*;UNIX.gid*;unique*; Response: MLSD Response: ESTA Response: PASV Response: EPSV Response: SPSV Response: ESTP Response: 211 End. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (210,245,88,98,138,1) Command: MLSD Error: Connection timed out Error: Failed to retrieve directory listing Status: Connecting to 210.245.88.98:21... Status: Connection established, waiting for welcome message... Help me.

    Read the article

  • How to organize deployment process in Chef-controlled environment?

    - by Alex
    I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

    Read the article

  • Restart my graphics card without rebooting?

    - by defaye
    Wondered if it is possible to use DevCon to restart a display device as a stop-gap solution to artifacts left over from a graphics card malfunction? In particular it leaves my cursor very un-user-friendly: I found out the hardware ID of my display adapter through device manager (below) [(windows key + pause break) - device manager - display adapters - right click your display adapter - properties - details - hardware ids.] I tried the commands (opened with admin privileges) devcon restart "PCI\VEN_1002" and devcon restart =display but it always come back with No devices restarted.. Is it even possible to restart the graphics card without a system reboot?

    Read the article

  • Spring-mvc project can't select from a particular mysql table

    - by Dan Ray
    I'm building a Spring-mvc project (using JPA and Hibernate for DB access) that is running just great locally, on my dev box, with a local MySQL database. Now I'm trying to put a snapshot up on a staging server for my client to play with, and I'm having trouble. Tomcat (after some wrestling) deploys my war file without complaint, and I can get some response from the application over the browser. When I hit my main page, which is behind Spring Security authentication, it redirects me to the login page, which works perfectly. I have Security configured to query the database for user details, and that works fine. In fact, a change to a password in the database is reflected in the behavior of the login form, so I'm confident it IS reaching the database and querying the user table. Once authenticated, we go to the first "real" page of the app, and I get a "data access failure" error. The server's console log gets this line (redacted): ERROR org.hibernate.util.JDBCExceptionReporter - SELECT command denied to user 'myDbUser'@'localhost' for table 'asset' However, if I go to MySQL from the shell using exactly the same creds, I have no problem at all selecting from the asset table: [development@tomcat01stg]$ mysql -u myDbUser -pmyDbPwd dbName ... mysql> \s -------------- mysql Ver 14.12 Distrib 5.0.77, for redhat-linux-gnu (i686) using readline 5.1 Connection id: 199 Current database: dbName Current user: myDbUser@localhost ... UNIX socket: /var/lib/mysql/mysql.sock -------------- mysql> select count(*) from asset; +----------+ | count(*) | +----------+ | 19 | +----------+ 1 row in set (0.00 sec) I've broken down my MySQL access settings, cleaned out the user and re-run the grant commands, set up a version of the user from 'localhost' and another from '%', making sure to flush permissions.... Nothing is changing the behavior of this thing. What gives?

    Read the article

  • Why does my screen dim on a desktop installation of Windows 7?

    - by Robert Cartaino
    Periodically, while using my Windows 7 Pro desktop installation, the screen suddenly dims. The brightness is about 75% normal (estimate). It's as if I am in a power-saving mode on a laptop running on batteries. But this is a full desktop installation. I know it is not a hardware glitch or monitor adjustment issue because the Windows cursor is still bright white while everything else goes dim. The Control Panel Power Options have not been changed. They are set to "Balanced [active]" and I have tried restoring the default settings. Flipping through the power and display settings, everything looks "normal." There is no screen saver or power-off-after settings apparent. Rebooting the system resets everything to full brightness but I can't find a way to restore it in Windows or to keep it from happening in the first place. Suggestions?

    Read the article

  • Unable to boot fedora 11

    - by csunwold
    I have been running fedora 11 for several months without a hiccup, but two days ago I ran "yum update" and installed whatever updates were available (I didn't pay attention to what they were). I was having problems with mysql so I tried "yum remove mysql" and then it removed mysql as well as quite a few unexpected dependencies. I then "yum install mysql" without a hitch and went about my way. However, when I next booted up my machine it got to "Starting preload dameon [OK]" and then it hangs with a flashing cursor on the screen. I tried following http://dailypackage.fedorabook.com/i...ling-Grub.html but it didn't seem to make any difference. I put a new hard drive with WinXP on it into the same machine that I booted to, and I tried to use Ext2 Installable File System for Windows but when I run it, it only seems to see /boot and nothing else on the hard drive. Any ideas?

    Read the article

  • VMware NAS/iSCSI recommendations - smallish organization

    - by Bubnoff
    I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

    Read the article

  • Trackpad Drag lock pissing me off with Windows 7

    - by rockinthesixstring
    This is driving me insane and I've scowered the web for two days trying to fix this. I just picked up an Apple Magic Trackpad to be used exclusively on a Windows 7 PC (not apple with bootcamp). I found a nice driver that got it working right away, but when I'm moving the cursor around the screen, often it will begin "highlighting" text, or picking up and dragging things I don't want it to. I looked in the "regedit" where people are saying there is binary that can be changed, however the driver I installed doesn't use the binary being suggested. Can anyone suggest a better driver for my situation or a way to disable the drag lock that is driving me so nuts? I don't mind not being able to lift my finger when dragging, it's a far better compromise than having the insane feature.

    Read the article

  • Why cant i install ANY operating system??

    - by Ranhiru
    I tested the memory and i tested the hard disk and everything is fine! Mini XP booted from Hirens Boot Disk works :( I tried Windows 7, Windows XP SP3 and even Ubuntu 10.04 :( All Operating Systems boots up to the point where they can load necessary files to start the OS and then resets the laptop Windows 7, only up to the point where the Windows Loading Animation is happening Ubuntu, only up to the point where the loading is done, shows a small screen and then goes to a blinking cursor and thats it... it keeps on blinking and sometimes resets the computer Windows XP SP3, loads all the drivers and everything and then the point where i should be able install the OS, it simply resets the laptop :( I have used the word reset instead of restart because the laptop completely turns off and then only turns back in Any solutions would be greatly appreciated

    Read the article

  • How do I customize zsh's vim mode?

    - by Jason Baker
    Ok, so I finally made the great change. In my .zshenv, I changed my EDITOR: export EDITOR=vim There are a couple of questions I have that are so minor that I didn't want to start separate questions for them. Here they are: How do I get zsh to distinguish between insert mode and command mode like in vim? Preferably this would change the cursor from an underline to a block like in vim, but displaying text at the bottom would work as well. How do I get it to act more like vim? For instance, I'd rather it be in command mode by default and not go out of it after one command.

    Read the article

  • Windows 7 setup hangs after "Starting Windows..."-screen

    - by Eirik Lillebo
    Hi! I'm having some trouble installing Windows 7. I need to install the OS from boot in order to split my C: into two different partitions, as this is not allowed when installing from inside Vista. When I boot up from the install disc, I get the usual "Windows is copying files..."-screen, shortly followed by the "Starting Windows..."-screen with the animated window-logo or whatever. Then it looks as if the installation is about to begin with a blue screen and a cursor I can move around, but here it all stops. Nothing more happens, and the setup seems to hang. Not a single key on my keyboard has any effect, and all I am left to do is to abort and reboot. I've tried to install using two different DVDs (not clones), and the same thing happens every time. What may be causing this, and how may I fix it? Thanks in advance :)

    Read the article

  • Thecus N5200, disk has dropped out of RAID5

    - by Anders Ekdahl
    We have a Thecus 5200 NAS here at work with five WD Caviar Black 2TB disks in a RADI5 array. Yesterday, disk 4 dropped out of the array, and in the NAS web interface there's a warning about the RAID array being "degraded". When I go into Storage - Disks, disk 1 and 4 has a warning next to them. When I click on the warnings, this information about the disks are displayed: Tray Number 4 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 34 Reallocated Sector Count 66 Current Pending Sector 1447 Raw Read Error Rate 61 Seek Error Rate 0 Hardware ECC Recovered N/A Tray Number 1 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 32 Reallocated Sector Count 0 Current Pending Sector 1465 Raw Read Error Rate 0 Seek Error Rate 0 Hardware ECC Recovered N/A I'm not really an expert on either disks or RAID arrays. Does this indicate that the fourth disk is damaged, and needs to be replaced? And what about disk number one? It has a warning, but it's still in the array. Is it safe to add the fourth disk back into the array as a spare? I can't find any way to add it back as a it were before.

    Read the article

  • Hard Disk Not Counting Reallocated Sectors

    - by MetaNova
    I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

    Read the article

  • Attaching 3.5" desktop drive to MacBook SATA

    - by Kyle Cronin
    I have a mid-2007 MacBook that, according to the Apple Store, has suffered some liquid damage and requires a new logic board to operate correctly, a ~$750 repair I've been told (would normally be around ~$300 were it not for the "liquid damage"). The unit itself works fine - the only problem I've been having is that the system does not recognize the battery and will not charge it. Curiously, the system can still be powered by the battery and even recognizes when the power cord is detached by diming the backlight, but I digress. Now that this laptop will likely become a desktop, I'm wondering if it might be possible to attach a desktop drive. I recently purchased a 2TB SATA drive and I'm wondering if it's possible to somehow attach it where the current internal drive connects. Obviously the drive itself will not fit inside the device, but as the unit will spend the rest of its days on my desk, that's not really much of an issue. My main questions are: Is this possible? If so, how would I connect the drive? Would a SATA extender cable work? Is the SATA port on my MacBook capable of powering a desktop drive? Or should I just get a SATA male-to-female cable and see if I can power the drive through other means (a cheap power supply, for example) The disk I'm referring to is the Hitachi Deskstar HD32000. Though I couldn't find that exact model on Hitachi's support site, these are the power requirements for a similar drive, the 7K2000 (2TB, 7200RPM, SATA II): Power Requirement +5 VDC (+/-5%) +12 VDC (+/-10%) Startup current (A, max.) 1.2 (+5V), 2.0 (+12V) Idle (W) 7.5 From what I've read, 2.5" drives require 5V, meaning that my MacBook obviously is capable of producing it. The specs seem to suggest that this drive seems capable of accepting it instead of the typical 12V - is this an accurate interpretation of the power requirements? Or does it need both 12V and 5V?

    Read the article

  • How do I change until the next underscore in VIm?

    - by Nathan Long
    If I have this text in vim, and my cursor is at the first character: www.foo.com I know that I can do: cw to change up to the first period, because a word (lowercase w) ends at any punctuation OR white space cW to change the whole address, because a Word (uppercase w) ends only at whitespace Now, what if I have this: stupid_method_name and want to change it to this? awesome_method_name Both cw and cW change the whole thing, but I just want to change the fragment before the underscore. My fallback technique is c/_, meaning 'change until you hit the next underscore in a search,' but for me, that also causes all underscores to be highlighted as search terms, which is slightly annoying. Is there a specifier like w or W that doesn't include underscores?

    Read the article

  • Sync desktop Mac environment to laptop

    - by Andrew Vit
    I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

    Read the article

  • HELP PLEASE!!!! External component has thrown an exception. ASP.NET ASPX PAGE POST

    - by Brandon
    I have an aspx page that communicates with a webservice I have. It connects to an SQL Server database on my virtual dedicated server. With just a little usage, I get this error External component has thrown an exception. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Runtime.InteropServices.SEHException: External component has thrown an exception. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [SEHException (0x80004005): External component has thrown an exception.] Luxand.FSDK.Initialize(String DataFilesPath) +0 WebService.onLoad() +70 WebService..ctor() +91 facematch.btn_submit_Click(Object sender, EventArgs e) +218 System.Web.UI.WebControls.Button.OnClick(EventArgs e) +105 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) +107 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument) +7 System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) +11 System.Web.UI.Page.RaisePostBackEvent(NameValueCollection postData) +33 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +1746

    Read the article

  • Is a Hyperthreaded CPU more powerful and more efficient than a Dual-core CPU? [closed]

    - by user1811864
    which computer to choose with Pentium processor hello they are getting rid of the old computer equipment in the office and i have to choose the computer to take home i get first choice to pick. -15 inch lcd screen 4 gb of ram core 2 duo dual Core E8400 3.00 GHz dvd writer windows vista/ linux -15 inch crt monitor with 2 gb ram and pentium 4 2 ghz single core HT technology windows xp hardisks both 250 GB my friend is telling me to choose the second one Pentium single core HT because he told me it runs faster becuase of HT technology and cooler and consumes less current electricity so it wont get overheated because it has HT technology so it's high definition for encoding and watching HD movies and HD sound and is like a gaming pc to play internet games. And also he said the dual core 8400 runs at 3 ghz compared to the 2 ghz so it heats very much because of the two extra cores so it takes more current raising electricty bills and is not good for gaming and watching HD movies and internet flash animations and games because of getting heated everytime. And he wants to choose and take the E8400 because he has air conditioning at home so it will be safe from heating. So which one computer should i take is it really faster because of the HT High definition technology and will i be able to play internet flash card games better and watch good HD movies Youtube etc and play all the music and songs.

    Read the article

  • EventID 1058 Code 5, Sysvol is subdir of Sysvol - how to fix?

    - by nulliusinverba
    I have been trying to resolve this error, like many others: The processing of Group Policy failed. Windows attempted to read the file \domain.local\SysVol\domain.local\Policies{3EF90CE1-6908-44EC-A750-F0BA70548600}\gpt.ini from a domain controller and was not successful. Group Policy settings may not be applied until this event is resolved. This issue may be transient and could be caused by one or more of the following: a) Name Resolution/Network Connectivity to the current domain controller. b) File Replication Service Latency (a file created on another domain controller has not replicated to the current domain controller). c) The Distributed File System (DFS) client has been disabled. Error code: 5 = Access Denied. The incredibly helpful post is this one (http://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Server/2003_Server/A_1073-Diagnosing-and-repairing-Events-1030-and-1058.html). Quoting from this post: HERE IS A LIST OF POTENTIAL PROBLEMS THAT CAN LEAD TO 1030 AND 1058 EVENT ERRORS: --Sometimes the permissions of the file folders that contain Group policies (the Sysvol folder) can be corrupted. --Sometimes you have problems with NetBIOS: --Sometimes the GPO itself is corrupt, or you have a partial set of data for that GPO. --Sometimes you may have problems with File Replication Services, which almost always indicates a problem with DNS --Sysvol may be a subfolder of itself: Sysvol/Sysvol I have the problem listed where sysvol is a subfolder of sysvol. The directory structure is: -sysvol -domain -staging -staging areas -sysvol (shared as "\\server\sysvol") -domain.local -ClientAgent -Policies -scripts Interestingly, the second sysvol folder is the one that is shared as "\server\sysvol". This makes me confident this is the issue with the permissions and error code 5. Also interestingly, my server 2008 R2 servers can see it fine - my server 2008 servers cannot, and get the error. This is consistent across all my servers. This latter fact makes me uncertain what I need to do to fix this up. Do I, e.g., simply move the shared sysvol folder up a level to replace the non-shared one? Any help greatly appreciated. Cheers, Tim.

    Read the article

  • Why can't I see all of the client certificates available when I visit my web site locally on Windows 7 IIS 7?

    - by Jay
    My team has recently moved to Windows 7 for our developer machines. We are attempting to configure IIS for application testing. Our application requires SSL and client certificates in order to authenticate. What I've done: I have configured IIS to require SSL and require (and tried accept) certificates under SSL Settings. I have created the https binding and set it to the proper server certificate. I've installed all the root and intermediate chain certificates for the soft certificates properly in current user and local machine stores. The problem When I browse to the web site, the SSL connection is established and I am prompted to choose a certificate. The issue is that the certificate is one that is created by my company that would be invalid for use in the application. I am not given the soft certificates that I have installed using MMC and IE. We are able to utilize the soft certs from our development machines to our Windows 2008 servers that host the application. What I did: I have attempted to copy the Root CA to every folder location for the Current User and Location Machine account stores that the company certificate's root is in. My questions: Could I be mishandling the certs anywhere else? Could there be a local/group policy that could be blocking the other certs from use? What (if anything) should have to be done differently on Windows 7 from 2008 in regards to IIS? Thanks for your help.

    Read the article

  • Cant install windows 7(boot problem)

    - by Vadiklk
    First of all, I cant boot my windows 7. I get a black screen with a cursor up in the left corner. So, I tried using windows 7 installation which I've put on my flash drive. To boot from the drive, I've changed the boot order to boot from the drive first. It boots but does not find any HDD to install the windows on(which is pretty logic, I dont boot the HDD soon enough for the installer). but if i put the HDD in front of the flash drive in the boot order, it will just try to load windows 7 and i will get the black screen again. I've tried putting the HDD first and clicking f8 a lot. All I've got is an error. Something about some software change. I dunno. Help me please, cant do anything with my laptop till then.

    Read the article

  • SELinux - Allow multiple services access to same /home/dir

    - by Mike Purcell
    I currently have SELinux enabled and have been able to configure apache to allow access to /home/src/web with a chcon command granting the 'httpd_sys_content_t' type. But now I am trying to serve the rsyslogd.conf file from the same directory, but every time I start rsyslogd I see an entry in my audit log saying that rsyslogd was denied access. My question is, is it possible to grant two applications the ability to access the same directory, while still keeping SELinux enabled? Current perms on /home/src: drwxr-xr-x. src src unconfined_u:object_r:httpd_sys_content_t:s0 src Audit log message: type=AVC msg=audit(1349113476.272:1154): avc: denied { search } for pid=9975 comm="rsyslogd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:syslogd_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349113476.272:1154): arch=c000003e syscall=2 success=no exit=-13 a0=7f9ef0c027f5 a1=0 a2=1b6 a3=0 items=0 ppid=9974 pid=9975 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=30 comm="rsyslogd" exe="/sbin/rsyslogd" subj=unconfined_u:system_r:syslogd_t:s0 key=(null) -- Edit -- Came across this post, which is sort of what I am trying to accomplish. However when I viewed the list of allowed sebool params, the only relating to syslog was: syslogd_disable_trans (SELinux Service Protection), seems like I can maintain the current SELinux 'type' on the /home/src/ dir, but set the bool on syslogd_disable_trans to false. I wonder if there is a better approach?

    Read the article

  • How can I "filter" postfix-generated bounce messages?

    - by Flimzy
    We are using postfix 2.7 and custom SMTPD (based on qpsmtpd) in highly customized configuration for spam filtering. We have a new requirement to filter postfix-generated bounces through our custom qpsmtpd process (not so much for content filtering, but to process these bounces accordingly). Our current configuration looks (in part) like this: main.cf (only customizations shown): 2526 inet n - - - 0 cleanup pickup fifo n - - 60 1 pickup -o content_filter=smtp:127.0.0.2 Our smtpd injects messages to postfix on port 2526, by speaking directly to the cleanup daemon. And the custom pickup command instructs postfix to hand off all locally-generated mail (from cron, nagios, or other custom scripts) to our custom smtpd. The problem is that this configuration does not affect postfix generated bounce messages, since they do not go through the pickup daemon. I have tried adding the same content_filter option to the bounce daemon commands, but it does not seem to have any effect: bounce unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 defer unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 trace unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 For reference, here is my main.cf file, as well: biff = no # TLS parameters smtpd_tls_loglevel = 0 smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${queue_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${queue_directory}/smtp_scache smtp_tls_security_level = may mydestination = $myhostname alias_maps = proxy:pgsql:/etc/postfix/dc-aliases.cf transport_maps = proxy:pgsql:/etc/postfix/dc-transport.cf # This is enforced on incoming mail by QPSMTPD, so this is simply # the upper possible bound (also enforced in defaults.pl) message_size_limit = 262144000 mailbox_size_limit = 0 # We do our own message expiration, but if we set this to 0, then postfix # will try each mail delivery only once, so instead we set it to 100 days # (which is the max postfix seems to support) maximal_queue_lifetime = 100d hash_queue_depth = 1 hash_queue_names = deferred, defer, hold I also tried adding the internal_mail_filter_classes option to main.cf, but also tono affect: internal_mail_filter_classes = bounce,notify I am open to any suggestions, including handling our current content-filtering-loop in a different way. If it's not clear what I'm asking, please let me know, and I can try to clarify.

    Read the article

  • Hyper-V Guests suddenly stopped working

    - by Anton Gogolev
    Hi! Here's my configuration: Windows Server 2008 R2 Standard as a host OS, and two guests VMs running the same exact OS. Yesterday, Trial Activation on all OSes has expired and quite naturally all machines shut down. I rearmed the host, but cannot log on to either guest VMs. From what I see, they start up normally (State is listed as Running) but CPU Usage seems to be stuck at 3% and when I connect to it all I see is black textmode screen with cursor blinking. One of my VMs has several snapshots, and when I revert back, it starts up normally. Moreover, "reference VM" (the one I cloned these two VMs from) starts up just normally. How can I troubleshoot this issue?

    Read the article

< Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >