Search Results

Search found 19441 results on 778 pages for 'static libraries'.

Page 218/778 | < Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >

• IPv6 routing to another interface

  - by Robert

  I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues. When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router. My PC is directly attached to FA 0/1 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything. I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response. I'm running on IOS 12.4. I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert Topology: R1 FA 0/0: 2001:0000:0000:0000::1/52 FA 0/1: 2001:0000:0000:1000::1/52 FA 1/0: 2001:0000:0000:2000::1/52 Loopback 0: 2001:0000:0000:3000::1/52 PC: 2001:0000:0000:2000::2/52 PC plugs directly into FA 1/0 on the router. --- Configuration --- ipv6 cef ipv6 unicast routing interface Loopback0 no ip address ipv6 address 2001:0000:0000:3000::1/52 ipv6 enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000::1/52 ipv6 enable ! interface FastEthernet0/1 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:1000::1/52 ipv6 enable ! interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:2000::1/52 ipv6 enable --- end of config --- --- routing table --- IPV6Lab#show ipv6 route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2001:0000:0000::/52 [0/0] via ::, FastEthernet0/0 L 2001:0000:0000::1/128 [0/0] via ::, FastEthernet0/0 C 2001:0000:0000:1000::/52 [0/0] via ::, FastEthernet0/1 L 2001:0000:0000:1000::1/128 [0/0] via ::, FastEthernet0/1 C 2001:0000:0000:2000::/52 [0/0] via ::, FastEthernet1/0 L 2001:0000:0000:2000::1/128 [0/0] via ::, FastEthernet1/0 C 2001:0000:0000:3000::/52 [0/0] via ::, Loopback0 L 2001:0000:0000:3000::1/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 --- end of routing table ---

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• How to have 2 windows machines on the same network with the same IP address

  - by Stu

  I have a custom made ADC device that is spitting out data by addressed UDP packets. I have that device plugged into a 4 port switch. I have one windows embedded standard 7 machine which is the normal recipient of that data. To be able to receive the data (Using LabVIEW) the windows network adapter IPv4 settings must have a static IP address that corresponds to the UDP packet destination. I would like to add a second windows machine (This one is just regular Win 7 Pro) to simultaneously catch the data, however with all devices connected to the switch, the Win 7 Pro machine recognizes an IP address conflict and will not take the setting for the required static IP address. (The network adaptor settings show that the correct value has been entered but ipconfig shows that it is not actually set.) Neither windows machine needs to transmit network data, they only need to be able to receive the UDP data from the ADC device. Is there any way to disable this IP address conflict detection 'feature' of windows networking?

  Read the article

• Hiding "Syntax OK" from apache2ctl output

  - by Oscar Barrett

  I am checking whether a particular apache module is installed using apache2ctl -M. When listing the modules, apache runs a syntax check on the configuration files which prints out "Syntax OK" if everything is fine. However, this message doesn't seem to be coming from STDOUT or STDERR as it shows even if all output is redirected to /dev/null. i.e. $ sudo apache2ctl -M Loaded Modules: core_module (static) log_config_module (static) ... Syntax OK $ sudo apache2ctl -M >/dev/null Syntax OK How is this being outputted, and is it possible to hide?

  Read the article

• How to remove the last character from Stringbuilder

  - by hmloo

  We usually use StringBuilder to append string in loops and make a string of each data separated by a delimiter. but you always end up with an extra delimiter at the end. This code sample shows how to remove the last delimiter from a StringBuilder. using System; using System.Collections.Generic; using System.Text; using System.Linq; class Program { static void Main() { var list =Enumerable.Range(0, 10).ToArray(); StringBuilder sb = new StringBuilder(); foreach(var item in list) { sb.Append(item).Append(","); } sb.Length--;//Just reduce the length of StringBuilder, it's so easy Console.WriteLine(sb); } } //Output : 0,1,2,3,4,5,6,7,8,9 Alternatively,  we can use string.Join for the same results, please refer to blow code sample. using System; using System.Collections.Generic; using System.Text; using System.Linq; class Program { static void Main() { var list = Enumerable.Range(0, 10).Select(n => n.ToString()).ToArray(); string str = string.Join(",", list); Console.WriteLine(str); } }

  Read the article

• Do all domains on the same shared hosting server have the same IP or ID

  - by silow

  Here's what I've got: siteA.com and siteB.com are hosted on hostgator. They're hosted on the same account of a shared hosting server (not VPS or dedicated). script.php is an external site that each of these 2 sites are accessing. I noticed that when siteA.com or siteB.com access the outside script.php, the script identifies them both as 1a.12.12ab.static.theplanet.com (apparently because hostgator uses theplanet.com servers). The fact that they're identified as the same value isn't surprising because after all they're hosted on the same account /home/user123/public_html. What I'm wondering about is how about other websites that are hosted on the same shared hosting server, but under other accounts. Basically other websites that are under another developer's control, but just happen to share the same hardware (hosting server). Do they also have the exact same identifier 1a.12.12ab.static.theplanet.com or that changes by account?

  Read the article

• Languages with a clear distinction between subroutines that are purely functional, mutating, state-changing, etc?

  - by CPX

  Lately I've become more and more frustrated that in most modern programming languages I've worked with (C/C++, C#, F#, Ruby, Python, JS and more) there is very little, if any, language support for determining what a subroutine will actually do. Consider the following simple pseudo-code: var x = DoSomethingWith(y); How do I determine what the call to DoSomethingWith(y) will actually do? Will it mutate y, or will it return a copy of y? Does it depend on global or local state, or is it only dependent on y? Will it change the global or local state? How does closure affect the outcome of the call? In all languages I've encountered, almost none of these questions can be answered by merely looking at the signature of the subroutine, and there is almost never any compile-time or run-time support either. Usually, the only way is to put your trust in the author of the API, and hope that the documentation and/or naming conventions reveal what the subroutine will actually do. My question is this: Does there exist any languages today that make symbolic distinctions between these types of scenarios, and places compile-time constraints on what code you can actually write? (There is of course some support for this in most modern languages, such as different levels of scope and closure, the separation between static and instance code, lambda functions, et cetera. But too often these seem to come into conflict with each other. For instance, a lambda function will usually either be purely functional, and simply return a value based on input parameters, or mutate the input parameters in some way. But it is usually possible to access static variables from a lambda function, which in turn can give you access to instance variables, and then it all breaks apart.)

  Read the article

• World Location issues with camera and particle

  - by Joe Weeks

  I have a bit of a strange question, I am adapting the existing code base including the tile engine as per the book: XNA 4.0 Game Development by example by Kurt Jaegers, particularly the aspect that I am working on is the part about the 2D platformer in the last couple of chapters. I am creating a platformer which has a scrolling screen (similar to an old school screen chase), I originally did not have any problems with this aspect as it is simply a case of updating the camera position on the X axis with game time, however I have since added a particle system to allow the players to fire weapons. This particle shot is updated via the world position, I have translated everything correctly in terms of the world position when the collisions are checked. The crux of the problem is that the collisions only work once the screen is static, whilst the camera is moving to follow the player, the collisions are offset and are hitting blocks that are no longer there. My collision for particles is as follows (There are two vertical and horizontal): protected override Vector2 horizontalCollisionTest(Vector2 moveAmount) { if (moveAmount.X == 0) return moveAmount; Rectangle afterMoveRect = CollisionRectangle; afterMoveRect.Offset((int)moveAmount.X, 0); Vector2 corner1, corner2; // new particle world alignment code. afterMoveRect = Camera.ScreenToWorld(afterMoveRect); // end. if (moveAmount.X < 0) { corner1 = new Vector2(afterMoveRect.Left, afterMoveRect.Top + 1); corner2 = new Vector2(afterMoveRect.Left, afterMoveRect.Bottom - 1); } else { corner1 = new Vector2(afterMoveRect.Right, afterMoveRect.Top + 1); corner2 = new Vector2(afterMoveRect.Right, afterMoveRect.Bottom - 1); } Vector2 mapCell1 = TileMap.GetCellByPixel(corner1); Vector2 mapCell2 = TileMap.GetCellByPixel(corner2); if (!TileMap.CellIsPassable(mapCell1) || !TileMap.CellIsPassable(mapCell2)) { moveAmount.X = 0; velocity.X = 0; } return moveAmount; } And the camera is pretty much the same as the one in the book... with this added (as an early test). public static void Update(GameTime gameTime) { position.X += 1; }

  Read the article

• Google+ Platform Office Hours for May 16th, 2012: Hangouts API v1.1

  Google+ Platform Office Hours for May 16th, 2012: Hangouts API v1.1 This week we discussed the latest release of the Hangouts API, v1.1. JD Salazar and Richard Dunn from the Hangouts API engineering team joined us to help your answer questions. Discussion this session on Google+: goo.gl You can learn more about our office hours here: goo.gl 0:29 - Introductions 2:50 - Richard gives us an overview of what's new in Hangouts API v1.1 8:57 - What are the default scales for the static overlays? 9:25 - Will the static overlay scale ratio change during the hangout? 10:13 - What is the resolution of the feed? How do I ensure my overlays match the quality? 12:49 - How do I know if an image resource has failed to load? 16:33 - Can we have animated gifs as overlays? 19:44 - Loaded overlays do not clear upon deletion. How many can I load before I encounter issues? 21:48 - Are sound overlays played to all participants or only locally? What about sound cancellation? 23:27 - How do you uninstall a Hangout app? 25:41 - Can I make an app that uses drag and drop onto the film strip? 26:55 - Can we embed participant thumbnails elsewhere on the screen? 28:33 - How can I determine a consistent ordering for hangout participants? 31:35 - Can I access Picasa photos uploaded by another user within a hangout? Gerwin demonstrates his solution. 31:14 - How do I know when my hangout app has been unloaded for the purposes of doing cleanup? 39:28 - Will face tracking ever support multiple faces? 40:41 - Can I use WebGL in a hangouts app? 42:09 - I'm having issues with <b>...</b> From: GoogleDevelopers Views: 2032 18 ratings Time: 53:05 More in Science & Technology

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• IIS: Content-Length 0 for CSS, Javascript and Images

  - by Adrian Grigore

  After a clean re-installation of my Windows 7 system, I can't get IIS 7 to properly deliver any static content. Dynmic content (ASPX pages and content served by ASP.NET MVC controllers) works fine, but static files such as CSS, Javascript and Images give me a 200 OK status code and a Content-Length of 0. The problem occurs with all web sites on my server, even a brandnew ASP:NET MVC template project with no changes. It also occurs with both Firefox and IE 8. What could possibly be the problem? Note that I also installed the latest Windows Azure SDK, perhaps that messed up some settings. But I don't know how to proceed with for troubleshooting this.

  Read the article

• .NET app - Should we use SQL Server and duplicate some reference data from an external Oracle DB? Or use Oracle and have a DB link?

  - by Daventry

  We're looking to migrate some existing Excel/Access processes into a new system which will provide the users with a Silverlight frontend to run and view the reports instead of using MS Access. The initial idea was to have SQL Server 2008 as RDBMS. The problem is that we've got some static data such as country codes, counterparties, etc which live in an existing Oracle DB. Since we do not want to duplicate that data (if possible), we were thinking of having a DB link between SQL Server and Oracle, but our firm does not allow that. So the options are either duplicate the data or use Oracle as RDBMS - surprise, the firm does allow DB links between Oracle databases. The initial idea was also to use WCF RIA Services, Entity Framework, etc which we're not sure they play well with Oracle, that's why it was decided to go with SQL Server in the first place. Would you advise to go for Oracle so that we can just link the static data? Or use SQL Server 2008 and replicate it because it's "safer" to stay within the Microsoft land? To use or not to use Entity Framework and WCF RIA Services at all? Regards. UPDATE: Thanks everyone for your answers. Nothing is set in stone yet. We'll try to import the data instead of linking, as if the other DB goes down, our system can still carry on. We're likely to use SQL Server just because most developers are more experienced with it. Even if we used RIA Services, we can swap out the Data Access Layer and use other frameworks such those mentioned below.

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• How to install PyQt on Mac OS X 10.6

  - by Albert

  I want to install PyQt. This seems kind of complicated to install on OS X. I haven't found any precompiled packages of it (are there any? I would really prefer those). So I downloaded PyQt. And SIP, because it depends on that. These files: http://www.riverbankcomputing.co.uk/static/Downloads/PyQt4/PyQt-mac-gpl-4.7.3.tar.gz http://www.riverbankcomputing.co.uk/static/Downloads/sip4/sip-4.10.2.tar.gz Did a python configure.py && make && sudo make install on SIP -- installed without any problems. Tried the same on PyQt -- and failed of course: /Library/Frameworks/QtCore.framework/Headers/qglobal.h:288:2: error: #error "You are building a 64-bit application, but using a 32-bit version of Qt. Check your build configuration." Ok, so I tried with python configure.py --use-arch=i386. Same error. Any idea?

  Read the article

• How to run django on localhost with nginx and uwsgi?

  - by user2426362

  How to run django on localhost with nginx and uwsgi? This im my config but not works. nginx: server { listen 80; server_name localhost; access_log /var/log/nginx/localhost_access.log; error_log /var/log/nginx/localhost_error.log; location / { uwsgi_pass unix:///tmp/localhost.sock; include uwsgi_params; } location /media/ { alias /home/user/projects/zt/myproject/myproject/media/; } location /static/ { alias /home/user/projects/zt/myproject/myproject/static/; } } uwsgi: [uwsgi] vhost = true plugins = python socket = /tmp/localhost.sock master = true enable-threads = true processes = 2 wsgi-file = /home/user/projects/zt/myproject/myproject/wsgi.py virtualenv = /home/user/projects/zt chdir = /home/user/projects/zt/myproject touch-reload = /home/user/projects/zt/myproject/reload This config work on my ubuntu server with normal domain (not localhost) but on localhost not working. If I run localhost in web browser I have Welcome to nginx!

  Read the article

• Apache config that uses two document roots based on whether the requested resource exists in the first [closed]

  - by mattalexx

  Background I have a client site that consists of a CakePHP installation and a Magento installation: /web/example.com/ /web/example.com/app/ <== CakePHP /web/example.com/app/webroot/ <== DocumentRoot /web/example.com/app/webroot/store/ <== Magento /web/example.com/config/ <== Site-wide config /web/example.com/vendors/ <== Site-wide libraries The server runs Apache 2.2.3. The problem The whole company has FTP access and got used to clogging up the /web/example.com/, /web/example.com/app/webroot/, and /web/example.com/app/webroot/store/ directories with their own files. Sometimes these files need HTTP access and sometimes they don't. In any case, this mess makes my job harder when it comes to maintaining the site. Code merges, tarring the live code, etc, is very complicated and usually requires a bunch of filters. Abandoned solution At first, I thought I would set up a new subdomain on the same server, move all of their files there, and change their FTP chroot. But that wouldn't work for these reasons: Firstly, I have no idea (and neither do they remember) what marketing materials they've sent out that contain URLs to certain resources they've uploaded to the server, using the main domain, and also using abstract subdomains that use the main virtual host because it has ServerAlias *.example.com. So suddenly having them only use static.example.com isn't feasible. Secondly, The PHP scripts in their projects are potentially very non-portable. I want their files to stay in as similar an environment as they were built as I can. Also, I do not want to debug their code to make it portable. Half-baked solution After some thought, I decided to find a way to section off the actual website files into another directory that they would not touch. The company's uploaded files would stay where they were. This would ensure that I didn't break any of their projects that needed HTTP access. It would look something like this: /web/example.com/ <== A bunch of their files are in here /web/example.com/app/webroot/ <== 1st DocumentRoot; A bunch of their files are in here /web/example.com/app/webroot/store/ <== Some more are in here /web/example.com/site/ <== New dir; Contains only site files /web/example.com/site/app/ <== CakePHP /web/example.com/site/app/webroot/ <== 2nd DocumentRoot /web/example.com/site/app/webroot/store/ <== Magento /web/example.com/site/config/ <== Site-wide config /web/example.com/site/vendors/ <== Site-wide libraries After I made this change, I would not need to pay attention to anything except for the stuff within /web/example.com/site/ and my job would be a lot easier. I would be the only one changing stuff in there. So here's where the Apache magic would happen: I need an HTTP request to http://www.example.com/ to first use /web/example.com/app/webroot/ as the document root. If nothing is found (no miscellaneous uploaded company projects are found), try finding something within /web/example.com/site/app/webroot/. Another thing to keep in mind is, the site might have some problems if the $_SERVER['DOCUMENT_ROOT'] variable reads /web/example.com/app/webroot/ but the actual files are within /web/example.com/site/app/webroot/. It would be better if the DOCUMENT_ROOT environment variable could be /web/example.com/site/app/webroot/ for anything within the /web/example.com/site/app/webroot/ directory. Conclusion Is my half-baked solution possible with Apache 2.2.3? Is there a better way to solve this problem?

  Read the article

• Renaming Nginx 1.3.5 Server: response header

  - by Ryan

  In nginx 1.2 & 1.3 you can modify the source to change the name: src/http/ngx_http_header_filter_module.c (lines 48 and 49): static char ngx_http_server_string[] = "Server: Not Nginx" CRLF; static char ngx_http_server_full_string[] = "Server: Not Nginx/1.0" CRLF; Renaming those and recompiling the source changes the server response name in nginx 1.2. However doing this in 1.3 does not seem to change the name. It still says nginx/1.3.5 and with server_tokens off; it just says nginx. How can I change the server name in 1.3 without installing the 3rd party addon headers more? I want to compile from source.

  Read the article

• Squibbly: LibreOffice Integration Framework for the Java Desktop

  - by Geertjan

  Squibbly is a new framework for Java desktop applications that need to integrate with LibreOffice, or more generally, need office features as part of a Java desktop solution that could include, for example, JavaFX components. Here's what it looks like, right now, on Ubuntu 13.04: Why is the framework called Squibbly? Because I needed a unique-ish name, because "squibble" sounds a bit like "scribble" (which is what one does with text documents, etc), and because of the many absurd definitions in the Urban Dictionary for the apparently real word "squibble", e.g., "A name for someone who is squibblish in nature." And, another e.g., "A squibble is a small squabble. A squabble is a little skirmish." But the real reason is the first definition (and definitely not the fourth definition): "Taking a small portion of another persons something, such as a small hit off of a pipe, a bite of food, a sip of a drink, or drag of a cigarette." In other words, I took (or "squibbled") a small portion of LibreOffice, i.e., OfficeBean, and integrated it into a NetBeans Platform application. Now anyone can add new features to it, to do anything they need, such as create a legislative software system as Propylon has done with their own solution on the NetBeans Platform: For me, the starting point was Chuk Munn Lee's similar solution from some years ago. However, he uses reflection a lot in that solution, because he didn't want to bundle the related JARs with the application. I understand that benefit but I find it even more beneficial to not need to require the user to specify the location of the LibreOffice location, since all the necessary JARs and native libraries (currently 32-bit Linux only, by the way) are bundled with the application. Plus, hundreds of lines of reflection code, as in Chuk's solution, is not fun to work with at all. Switching between applications is done like this: It's a work in progress, a proof of concept only. Just the result of a few hours of work to get the basic integration to work. Several problems remain, some of them potentially unsolvable, starting with these, but others will be added here as I identify them: Window management problems. I'd like to let the user have multiple LibreOffice applications and documents open at the same time, each in a new TopComponent. However, I haven't figured out how to do that. Right now, each application is opened into the same TopComponent, replacing the currently open application. I don't know the OfficeBean API well enough, e.g., should a single OfficeBean be shared among multiple TopComponents or should each of them have their own instance of it? Focus problems. When putting the application behind other applications and then switching back to the application, typing text becomes impossible. When closing a TopComponent and reopening it, the content is lost completely. Somehow the loss of focus, and then the return of focus, disables something. No idea how to fix that. The project is checked into this location, which isn't public yet, so you can't access it yet. Once it's publicly available, it would be great to get some code contributions and tweaks, etc. https://java.net/projects/squibbly Here's the source structure, showing especially how the OfficeBean JARs and native libraries (currently for Linux 32-bit only) fit in: Ultimately, would be cool to integrate or share code with http://joeffice.com!

  Read the article

• Recursion in F#

  - by MarkPearl

  Things are slowly coming together – I was able to look at a bit of F# code and intuitively know what it was going to do (yay)… So today I saw a blog post by Bob Palmer on Fibonacci numbers in F# which inspired me to look at bit into recursion. First the C# example… class Program { public static void CountDown(int n) { switch (n) { case 0: Console.WriteLine("End of Count"); break; default: Console.WriteLine(n); CountDown(n-1); break; } } static void Main(string[] args) { CountDown(10); Console.ReadLine(); } }   In F#, the equivalent would look something like this… open System let rec CountDown n = match n with | 0 -> Console.WriteLine("End of Count"); | n -> Console.WriteLine(n); CountDown (n-1); CountDown 10 Console.ReadLine()   Pretty simple stuff. With F# you when making recursive calls you need to explicitly declare that the function is recursive with the “rec” keyword. Otherwise the code is pretty easy to read and self explanatory.

  Read the article

• Managing many draw calls for dynamic objects

  - by codetiger

  We are developing a game (cross-platform) using Irrlicht. The game has many (around 200 - 500) dynamic objects flying around during the game. Most of these objects are static mesh and build from 20 - 50 unique Meshes. We created seperate scenenodes for each object and referring its mesh instance. But the output was very much unexpected. Menu screen: (150 tris - Just to show you the full speed rendering performance of 2 test computers) a) NVidia Quadro FX 3800 with 1GB: 1600 FPS DirectX and 2600 FPS on OpenGL b) Mac Mini with Geforce 9400M 256mb: 260 FPS in OpenGL Now inside the game in a test level: (160 dynamic objects counting around 10K tris): a) NVidia Quadro FX 3800 with 1GB: 45 FPS DirectX and 50 FPS on OpenGL b) Mac Mini with Geforce 9400M 256mb: 45 FPS in OpenGL Obviously we don't have the option of mesh batch rendering as most of the objects are dynamic. And the one big static terrain is already in single mesh buffer. To add more information, we use one 2048 png for texture for most of the dynamic objects. And our collision detection hardly and other calculations hardly make any impact on FPS. So we understood its the draw calls we make that eats up all FPS. Is there a way we can optimize the rendering, or are we missing something?

  Read the article

• Binding BoundingSpheres to a world matrix in XNA

  - by NDraskovic

  I made a program that loads the locations of items on the scene from a file like this: using (StreamReader sr = new StreamReader(OpenFileDialog1.FileName)) { String line; while ((line = sr.ReadLine()) != null) { red = line.Split(','); model = row[0]; x = row[1]; y = row[2]; z = row[3]; elements.Add(Convert.ToInt32(model)); data.Add(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z))); sfepheres.Add(new BoundingSphere(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z)), 1f)); } I also have a list of BoundingSpheres (called spheres) that adds a new bounding sphere for each line from the file. In this program I have one item (a simple box) that moves (it has its world matrix called matrixBox), and other items are static entire time (there is a world matrix that holds those elements called simply world). The problem i that when I move the box, bounding spheres move with it. So how can I bind all BoundingSpheres (except the one corresponding to the box) to the static world matrix so that they stay in their place when the box moves?

  Read the article

• Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

  - by LaserBeak

  Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

  Read the article

• Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

  - by Lorenzo

  I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

  Read the article

• Good design for class with similar constructors

  - by RustyTheBoyRobot

  I was reading this question and thought that good points were made, but most of the solutions involved renaming one of the methods. I am refactoring some poorly written code and I've run into this situation: public class Entity { public Entity(String uniqueIdentifier, boolean isSerialNumber) { if (isSerialNumber) { this.serialNumber = uniqueIdentifier; //Lookup other data } else { this.primaryKey = uniqueIdentifier; // Lookup other data with different query } } } The obvious design flaw is that someone needed two different ways to create the object, but couldn't overload the constructor since both identifiers were of the same type (String). Thus they added a flag to differentiate. So, my question is this: when this situation arises, what are good designs for differentiating between these two ways of instantiating an object? My First Thoughts You could create two different static methods to create your object. The method names could be different. This is weak because static methods don't get inherited. You could create different objects to force the types to be different (i.e., make a PrimaryKey class and a SerialNumber class). I like this because it seems to be a better design, but it also is a pain to refactor if serialNumber is a String everywhere else.

  Read the article

• BoundingSpheres move when they should not

  - by NDraskovic

  I have a XNA 4.0 project in which I load a file that contains type and coordinates of items I need to draw to the screen. Also I need to check if one particular type (the only movable one) is passing in front or trough other items. This is the code I use to load the configuration: if (ks.IsKeyDown(Microsoft.Xna.Framework.Input.Keys.L)) { this.GraphicsDevice.Clear(Color.CornflowerBlue); Otvaranje.ShowDialog(); try { using (StreamReader sr = new StreamReader(Otvaranje.FileName)) { String linija; while ((linija = sr.ReadLine()) != null) { red = linija.Split(','); model = red[0]; x = red[1]; y = red[2]; z = red[3]; elementi.Add(Convert.ToInt32(model)); podatci.Add(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z))); sfere.Add(new BoundingSphere(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z)), 1f)); } } } catch (Exception ex) { Window.Title = ex.ToString(); } } The "Otvaranje" is an OpenFileDialog object, "elementi" is a List (determines the type of item that would be drawn), podatci is a List (determines the location where the items will be drawn) and sfere is a List. Now I solved the picking algorithm (checking for ray and bounding sphere intersection) and it works fine, but the collision detection does not. I noticed, while using picking, that BoundingSphere's move even though the objects that they correspond to do not. The movable object is drawn to the world1 Matrix, and the static objects are drawn into the world2 Matrix (world1 and world2 have the same values, I just separated them so that the static elements would not move when the movable one does). The problem is that when I move the item I want, all boundingSpheres move accordingly. How can I move only the boundingSphere that corresponds to that particular item, and leave the rest where they are?

  Read the article

< Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >