Search Results

Search found 18773 results on 751 pages for 'router configuration'.

Page 22/751 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Why does my router log crazy amounts of blocked traffic on port 1701?

  - by Vlad Seghete

  I have a 2701HGV-B 2Wire modem and router (AT&T). The log is basically full with entries similar to the following with a time between a fifth and a third of a second between entries: src=86.156.7.170 dst=xxx.xxx.xxx.38 ipprot=17 sport=6882 dport=1701 Unknown inbound session stopped src=58.176.22.252 dst=xxx.xxx.xxx.38 ipprot=17 sport=21573 dport=1701 Unknown inbound session stopped src=91.221.6.250 dst=xxx.xxx.xxx.38 ipprot=17 sport=25902 dport=1701 Unknown inbound session stopped ... where the source IP will be different for every entry. The entries accumulate constantly, every single second that the router is on several of them appear in the log. The destination is the WAN address for my router. I understand that this is somehow related to VNCs, but I don't know enough to figure out why my router is getting bombarded with requests for a VNC session. Is there anything fishy going on or is this normal? If it is normal, how do I keep these entries from spamming my log files? Since there's about two or three of them every second, everything else gets drowned out.

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• Building a better .NET Application Configuration Class - revisited

  - by Rick Strahl

  Managing configuration settings is an important part of successful applications. It should be easy to ensure that you can easily access and modify configuration values within your applications. If it's not - well things don't get parameterized as much as they should. In this post I discuss a custom Application Configuration class that makes it super easy to create reusable configuration objects in your applications using a code-first approach and the ability to persist configuration information into various types of configuration stores.

  Read the article

• How can I detect and delete all lost configuration folders?

  - by Takkat

  Over the time there is an increasing number of hidden .configuration folders in my home folder. Many of these come from applications I only installed for testing or from applications that I don't use any more. I would not mind really but these folders do clutter my home, and worse than that sum up to as much as 80 GBytes by now. As there are also applications I never heard of (at least I can't remember I had installed them) I hesitate to delete them. Is there a way to find out which folders came from purged applications? May there even be a way to auto-remove a configuration folder when purging (not removing) the application that created it?

  Read the article

• [StructureMap] Xml configuration or Configuration through code?

  - by Amith George

  I personally like the option to configure StructureMap from C# code. From what I understand, one of the advantages of DI, is that we can easily swap in a new concrete instance. But, if the configuration is defined in code, then the concrete instances are hardcoded in the dll. So, practically, its as good as having hard coded the dependencies, right? I know, during testing it makes life easier... My point is, wouldnt it be better to use xml configuration instead? you want to plugin a new concrete instance? simply have your installer overwrite the structuremap.config file with the new one. So, what is the preferred way to configure StructureMap? Extra: Am forced to use C# configuration for the time being because I dont know how to pass the connection string to instance. I can write the connectionstring in the config file, but i would like to reuse the connectionstring defined in app.config.

  Read the article

• What does "Local Domain Name" on router do and how do I get it to work?

  - by Giovanni Galbo

  I have a D-Link DGL-4500 router. One of the settings is "Local Domain Name," which I have set to local (see screenshot). What I expect is for me to be able to hit my computers via name, e.g. m6.local should resolve to one of my computers; but this isn't happening. I know that I can do this via hosts file, but it would be neat if I could do it via the router... plus I have devices like an iPad that don't let you edit the hosts file. Am I misunderstanding this router feature or am I doing something wrong?

  Read the article

• On a router, how do I block wan access for a particular machine without blocking its access to the local network?

  - by HappyEngineer

  On my tp-link TL-WR1043ND router I want to prevent a particular machine from having access to the WAN while still allowing that machine to access other machines on the LAN. My assumption is that I need to do something in the "Access Control" section, however the problem is that it wants an ip range or domain name for the target of the rule. The router uses DHCP to get an address from the WAN, so I don't have any guarantee what the ip address of the wan will be. If the answer is that it's not possible with this router, could someone describe how to do it using OpenWRT instead?

  Read the article

• Why would my router have different MAC addresses for IP and IPv6 transactions?

  - by user329161

  Today I was using tcpdump and I noticed my computer was having IPv6 traffic with a particular MAC address that I could not match with an IP using nmap or arping. After looking at the tcpdump logs a little more closely, I figured out it was another MAC address my router was using but exclusively for IPv6 traffic. 22:49:01.936830 90:0d:cb:ff:31:91 (oui Unknown) > 33:33:00:00:00:01 (oui Unknown), ethertype IPv6 (0x86dd), length 158: fe80::920d:cbff:feff:3191 > ip6-allnodes: ICMP6, router advertisement, length 104 Why would a router offer a different MAC address for IPv6?

  Read the article

• How to monitor the network traffic on a router?

  - by Adi

  Here's my current network set-up: we have 3 users connecting to a Thomson Gateway router (TG585 v8) provided by my ISP. We are connecting over an ADSL line. The problem is that we have a limited data allowance (60GB) and we always exceed it. I would like to monitor how much traffic each computer makes. The best solution would be to install a software on the router (like OpenWRT) which would monitor how much traffic each computer makes. But I couldn't find any replacement firmware that would support my router. The other solution would be to install a software on each machine and then collect all the data at the end of the mount. But that's not a very good think to do. Plus, the users can always shut down the application. Any suggestions?

  Read the article

• What kind of router do I need to handle multiple external I.P addresses?

  - by user1308743

  I have 3 dedicated I.P addresses going to a location with a few servers, and 1 RVS4000 router. Right now, only one I.P is being used. I would like a router that can use all 3 I.P addresses and I can make rules like this: IP1:80 goes to ServerA IP2:80 goes to ServerB What kind of router/device with what features do I need to handle this? I will need to set 30-40 rules to forward certain ports to certain servers. Only a couple ports will need to go to IP2 or IP3. Thanks

  Read the article

• Waht are the best proxy servers for Mikrotik router?

  - by niren

  I want to setup proxy server for my Mikrotik router. There is inbuilt web-proxy for Mikrotik router but I can extend this upto transparent proxy(kind of proxy server) only. We need High anonymity proxy so that we can hide our LAN static IPs(we don't have private IP) from outside Intruder/hackers. And also I know I can setup NAT rule to hide our IP(only private IP not public/static IP) as per this link, but I cann't hide static/public IP. Essentially I want to hide our Public/Static IP (there is static/public IP for all systems in our company) from outside Internet. To achieve this I guess I need other software apart from Mikrotik router gateway setup. can anyone suggest me Is there any other software to achieve my requirement? I know about squid proxy but am not sure whether It can hide our static/public IP. Note: we have assigned public/Static IP to all systems of our company since we have rights to access our company's system from anywhere by dedicated laptop(given by our company with more security) through VPN connection.

  Read the article

• What is a good router linux distro and WHY?

  - by madmaze

  I have a rather large home network with many clients. Ive decided I want to build a Linux based router, I have an 1.6Ghz dual-core(atom) system kicking around which will be re-purposed. So ive looked at a bunch of specific router distros but cant decide. I have also looked into taking a Ubuntu server or FreeBSD install and adding needed packages. So question is, what is the best router-Linux or base Linux distro and why? resources appreciated.

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• What happens when router has been set to incorrect time?

  - by iamrohitbanga

  I have a D-Link router for my home Wi-Fi network. Everyday at least once the internet suddenly goes down. I am simply not able to connect to the Wi-Fi network. If I just restart the router, it starts working. To debug the issue I logged into the admin panel and noticed the time was set to something in 2002. I have set it to the correct time. Will wait to see if that fixes the problem. In the meanwhile I want to know what can go bad when the router has been set to show an incorrect time? What are the kinds of problems expected? My Wi-Fi was working just fine most of the time, but sometimes it lost the connection. Could this be linked to the incorrect time setting?

  Read the article

• Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to

  - by Corey

  Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to a specific MAC address? I know the Linksys routers have a MAC filtering feature, but it is the opposite of what I need. It allows you to block access to a specific MAC address. I need something that will block all, but allow an exception. I'm dealing with some VOIP issues in my company's network, and I think the answer is to have a separate router on the network for my PBX to use. I want to make sure that other nodes are not allowed to access the Internet via this second router.

  Read the article

• Externalizing Grails Datasource configuration

  - by miek

  Grails 1.x allows using external configuration files by setting the grails.config.locations directive. Is there a similar approach available for externalizing the database configuration in Datasource.groovy (without setting up JNDI)? It would prove helpful to be able to configure DB credentials in a simple configuration file outside the application. Thanks in advance!

  Read the article

• Where can I find WebSphere configuration files?

  - by Nicholas Key

  Hello Stackoverflow'ers, I would like to know where are the WebSphere configuration details saved? Specifically, configuration details that are shown in the Administrative Console (from the web) or from the console using wsadmin. Some of the examples would be: Java and Process Management: Class loader, Process definition, Process execution Container Settings: Session management, SIP Container Settings, Web Container Settings, Portlet Container Settings Are there XML files that persist these configuration details? Nicholas

  Read the article

• Loading a ConfigurationSection with a required child ConfigurationElement with .Net configuration fr

  - by Vadim Rybak

  I have a console application that is trying to load a CustomConfigurationSection from a web.config file. The custom configuration section has a custom configuration element that is required. This means that when I load the config section, I expect to see an exception if that config element is not present in the config. The problem is that the .NET framework seems to be completely ignoring the isRequired attribute. So when I load the config section, I just creates an instance of the custom configuration element and sets it on the config section. My question is, why is this happening? I want the GetSection() method to fire a ConfigurationErrors exception since a required element is missing from the configuration. Here is how my config section looks. public class MyConfigSection : ConfigurationSection { [ConfigurationProperty("MyConfigElement", IsRequired = true)] public MyConfigElement MyElement { get { return (MyConfigElement) this["MyConfigElement"]; } } } public class MyConfigElement : ConfigurationElement { [ConfigurationProperty("MyAttribute", IsRequired = true)] public string MyAttribute { get { return this["MyAttribute"].ToString(); } } } Here is how I load the config section. class Program { public static Configuration OpenConfigFile(string configPath) { var configFile = new FileInfo(configPath); var vdm = new VirtualDirectoryMapping(configFile.DirectoryName, true, configFile.Name); var wcfm = new WebConfigurationFileMap(); wcfm.VirtualDirectories.Add("/", vdm); return WebConfigurationManager.OpenMappedWebConfiguration(wcfm, "/"); } static void Main(string[] args) { try{ string path = @"C:\Users\vrybak\Desktop\Web.config"; var configManager = OpenConfigFile(path); var configSection = configManager.GetSection("MyConfigSection") as MyConfigSection; MyConfigElement elem = configSection.MyElement; } catch (ConfigurationErrorsException ex){ Console.WriteLine(ex.ToString()); } } Here is what my config file looks like. <?xml version="1.0"?> <configuration> <configSections> <section name="MyConfigSection" type="configurationFrameworkTestHarness.MyConfigSection, configurationFrameworkTestHarness" /> </configSections> <MyConfigSection> </MyConfigSection> The wierd part is that if I open the config file and load the section 2 times in a row, I will get the exception that I expect. var configManager = OpenConfigFile(path); var configSection = configManager.GetSection("MyConfigSection") as MyConfigSection; configManager = OpenConfigFile(path); configSection = configManager.GetSection("MyConfigSection") as MyConfigSection; If I use the code above, then the exception will fire and tell me that MyConfigElement is required. The question is Why is it not throwing this exception the first time??

  Read the article

• can router configuration cause decreasing of download rate?

  - by Behrooz

  my download speed got crazy since i changed the routers IP. but nothing got fixed after "reset factory"ing it. the speed was 1024kb/s(128kB/s) but it is 200kb/s(max) right now. i mean it works good if a request is small(i.e. a HTTP request) but it gets slow if a request has a big response. help me please(it is three days I'm downloading VS2010) http://serverfault.com/questions/135243/ no one on serverfault helped me for posting my question please migrate it to serverfault. thanks.

  Read the article

• Platform configuration for projects in VS 2010

  - by Thomas Wanner

  I have a third-party project type in Visual Studio which for some reason only supports the .NET Platform configuration for the build, for all other (standard C#) projects in the solution I only have AnyCPU. Unfortunately, ever since upgrading to VS 2010 it produces following error when built : Error 39 The OutputPath property is not set for project 'ReferencedBusinessProject.csproj'. Please check to make sure that you have specified a valid combination of Configuration and Platform for this project. Configuration='Debug' Platform='.NET'. This error may also appear if some other project is trying to follow a project-to-project reference to this project, this project has been unloaded or is not included in the solution, and the referencing project does not build using the same or an equivalent Configuration or Platform. C:\Windows\Microsoft.NET\Framework\v4.0.30319\Microsoft.Common.targets 483 10 CustomTypeProject It's pretty much descriptive in what is missing but I haven't found any way to fix it so far. Do you have any idea how this can be resolved or what can be the problem ?

  Read the article

• how to change ASP.NET Configuration tool connection string

  - by Zviadi

  Hello, how can I change ASP.NET Configuration tool-s connection string name? (Which connection string will ASP.NET Configuration tool will use) I'm learning ASP.NET and everywhere and in book that I'm reading now theres connection string named: LocalSqlServer. I want to use my local sql server database instead of sql express to store Roles, Membership and other data. I have used aspnet_regsql.exe to create needed data structures in my database. after that I changed my web.config to look like: <connectionStrings> <remove name="LocalSqlServer"/> <add name="LocalSqlServer" connectionString="Server=(LOCAL); Database=MyDatabase;Integrated Security=True" providerName="System.Data.SqlClient" /> </connectionStrings> but when I run ASP.NET Configuration tool it says that: "The connection name 'ApplicationServices' was not found in the applications configuration or the connection string is empty." ASP.NET Configuration tool uses connection string named: ApplicationServices not LocalSqlServer. cause of that I have to modify web.config to: <connectionStrings> <add name="ApplicationServices" connectionString="Server=(LOCAL); Database=MyDatabase;Integrated Security=True" providerName="System.Data.SqlClient" /> </connectionStrings> and everything works fine. I wish to know why the hell my web site uses connection string named: ApplicationServices and all books and online documentations uses LocalSqlServer? and how to change it to LocalSqlServer? I have: Windows 7 Sql Server 2008 R2 Visual Studio 2010 Premium Project type is website

  Read the article

• Drupal 6 fails to build menu router and links

  - by Xinglin Zhang

  When I enable a new menu in Drupal (for example, mymodule), Drupal should be able to get the menu items from mymodule_menu (hook_menu), process the items and insert the menu items to menu_router and menu_links page. However, my Drupal fails to do so. Each time I enable a module (written by me or modules contributed by others, or core modules), Drupal does not seem to get the new information. The menu items defined in the newly enabled module are not processed and inserted to Drupal's menu system. That means the newly enabled module has no chance to work-- because it's inaccessible. I did fix this by manually insert the menu item information for the new module into the menu_router and menu_links table and the new menu started working. But this is a nightmare if I have to do this each time I enable a module. Any one has ever had the same problem? How to fix this? Thank you in advance.

  Read the article

• FreeBSD 8 Kernel Configuration Error Using the VESA Option

  - by gvkv

  I'm trying to reconfigure FreeBSD 8 (amd64) to allow for a high resolution terminal by following these instructions. The problem is that when I add the two lines: options VESA options SC_PIXEL_MODE and try to build: make buildkernel KERNCONF=VESAKERN I get the following error: /usr/src/sys/amd64/conf/VESAKERN: unknown option "VESA" and I have no idea why.

  Read the article

• BizTalk MQSC adapter configuration error & IBM WebSphere MQ Client V6.0

  - by chinna

  Hi Guys, I'm having trouble configuring the MSQC adapter for BizTalk Server 2006. At the moment I'm getting the following error when setting up a receive location or send port: The adapter "MQSC" raised an error message. Details "The specified module could not be found. (Exception from HRESULT: 0x8007007E) A dependency could not be found. Refer to product documentation for information on MQSC Adapter software prerequisites.".For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. I have installed the IBM WebSphere Client v6.0 installed but was unable to find the "IBM fix pack 6.0.1.1" for the WebSphere CLIENT as some people have suggested. I have found this post (http://www.biztalkgurus.com/forums/p/3719/7212.aspx) which seems to shed some light on this issue, but I am unable to find the fix-pack that they speak of or resolve the problem Is anybody able to provide any further information? A link to download the IBM WebSphere MQ Client V6.0 fix pack 6.0.1.1 would be a great start! Thanks, Jason

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >