Search Results

Search found 16665 results on 667 pages for 'nhibernate configuration'.

Page 222/667 | < Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• Wireless connection disconnects and reconnects with a Netgear WNA1000

  - by William Berkenkamp

  Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

  Read the article

• How To Export/Import a Website in IIS 7.x

  - by Tray Harrison

  IIS 6 had a great feature called ‘Save Configuration to a File’ which would allow you to easily export a website’s configuration, to be later used to import either on the same server or another box.  This came in handy anytime you wanted to duplicate a site in order to do some testing without impacting the existing application.  So naturally, Microsoft decided to do away with this feature in IIS 7. The process to export/import a site is still fairly simple, though not as obvious as it was in previous versions.  Here are the steps: 1. Open a command prompt and navigate to C:\Windows\System32\inetsrv and run the following command: appcmd list site /name:<sitename> /config /xml > C:\output.xml So if you were wanting to export a website named EAC, you would run the following: If you’ll be setting up another copy of the site on the same server, you’ll now need to edit the output.xml file before importing it.  This is necessary in order to avoid conflicts such as bindings, Site ID, etc.  To do this, edit the XML and change the values.  Go ahead and make a copy of the home directory, and rename it to whatever folder name you specified in the output – /EAC2 in this example.  If you decide to change the app pool, make sure you go ahead and create the new app pool as well. Once these edits have been made, we are now ready to import the site.  To do that run: appcmd add sites /in < c:\output.xml So for our example it would look like this: That’s it.  You should now see your site listed when opening up Inet Manager.  If for some reason the site fails to start, that’s probably because you forgot to create the new app pool or there is a problem with one of the other parameters you changed.  Look at the System log to identify any issues like this.

  Read the article

• Working with Active Directory and Windows Small Business Server 2008

  - by AreYouSerious

  I have to say that in most of my time as a network engineer I have had the opportunity to play with servers, but mostly it's been to put our management software on, and that was about it. I have been a Systems Network Engineer for about three months now, and as such I have been respnosible for the configuration of our test devices... this being said, I have had to start working through how to configure and apply such things as GPO through a new forest, domain and OU. This being said I have configured about three different GPO's and applied them to different locations. The first laptop that I brought into the domain took the default Domain group Policy... this was cool, I got excited... then When I tried to bring in the second Laptop, it didn't take the policy. I looked at the configuration, and the default domain policy was applied to domain computers, however since the laptop resides in the SBS Computers of the OU that was created, SBS created individual policies for XP and Vista for that OU, which I was unaware of. So the default policy for that ou overrode the domain policy and none of the options that were defined in the Domain policy were applied... this being said, I am now working on putting the default Domain as an applicable policy in the OU, thus I won't have to reconfigure another policy to mirror the Domain Policy... here goes nothing!!!.... More to follow Later.

  Read the article

• Forward nginx to Apache Tomcat

  - by erdimeola

  I'm totally new to nginx. I want to forward two subdomains to the two applications in my apache tomcat server. As I searched over internet, I found that rewrite does the forwarding but I cannot see forwarding. Here is my server configuration server { listen 80; server_name subdomain1.domain.com; rewrite ^ http://tomcat.ip:8080/app1$request_uri? permanent; } server { listen 80; server_name subdomain2.domain.com; rewrite ^ http://tomcat.ip:8080/app2$request_uri? permanent; } Whenever I invoke subdomain1.domain.com or subdomain2.domain.com, I'm redirected to the main page of nginx which states that nginx is successfully installed and further configuration is needed. So, How can I do the forwarding?

  Read the article

• If your algorithm is correct, does it matter how long it took you to write it?

  - by John Isaacks

  I recently found out that Facebook had a programming challenge that if completed correctly you automatically get a phone interview. There is a sample challenge that asks you to write an algorithm that can solve a Tower of Hanoi type problem. Given a number of pegs and discs, an initial and final configuration; Your algorithm must determine the fewest steps possible to get to the final configuration and output the steps. This sample challenge gives you a 45 minute time limit but allows you to still test your code to see if it passes once your time limit expires. I did not know of any cute math solution that could solve it, and I didn't want to look for one since I think that would be cheating. So I tried to solve the challenge the best I could on my own. I was able to make an algorithm that worked and passed. However, it took me over 4 hours to make, much longer than the 45 minute requirement. Since it took me so much longer than the allotted time, I have not attempted the actual challenge. This got me wondering though, in reality does it really matter that it took me that long? I mean is this a sign that I will not be able to get a job at a place like this (not just Facebook, but Google, Fog Creek, etc.) and need to lower my aspirations, or does the fact that I actually passed on my first attempt even though it took too long be taken as good?

  Read the article

• How can I join two simple home networks together using an ethernet cable?

  - by Ilia Jerebtsov

  I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

  Read the article

• How-To: Run CMSDK against a RAC cluster

  - by frank.closheim

  Using CMSDK in a production environment often requires a robust, reliable and failover enabled repository. When using Oracle Real Application Cluster (RAC) with your CMSDK repository you need to have a specific configuration in place to support such a setup. This post will explain the configuration steps required when running CMSDK 9.0.4.6 with Oracle WebLogic Server (WLS).In the previous CMSDK 9.0.4.2 version a RAC enabled connect string looked like this: (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = rac1)(PORT = 1521))(ADDRESS = (PROTOCOL = TCP)(HOST = rac2)(PORT = 1521))(LOAD_BALANCE = NO)(FAILOVER = ON)(CONNECT_DATA =(SERVICE_NAME = rac)(failover_mode = (type=select)(method=basic)))CMSDK 9.0.4.6 makes use of data sources to connect to the underlying database. These data sources are configured inside your Application Server, such as Oracle WebLogic Server.In Oracle WebLogic Server 10.3.4, a single data source implementation has been introduced to support an RAC cluster. It responds to Fast Application Notification (FAN) events to provide Fast Connection Failover (FCF), Runtime Connection Load-Balancing (RCLB), and RAC instance graceful shutdown. XA affinity is supported at the global transaction Id level. The new feature is called WebLogic Active GridLink for RAC; which is implemented as the GridLink data source within WebLogic Server.This GridLink data source also works with Oracle Single Client Access Name (SCAN). SCAN is a feature used in RAC environments that provides a single name for clients to access any Oracle Database running in a cluster. You can think of SCAN as a cluster alias for databases in the cluster. The benefit is that the client’s connect information does not need to change if you add or remove nodes or databases in the cluster.The CMSDK 9.0.4.6 documentation describes how to create a regular JDBC data source named jdbc/OracleDS. Please refer to the following document which describes in detail how to create a GridLink data source in WLS.

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• AWS:EC2:: Could not connect FTP client?

  - by heathub

  My Server OS: Amazon Linux I am trying to set up ftp. I have: Installed vsftpd open port 20-21 open port 1024 - 1048 Basically, I followed every of these steps Start vsftpd service (the status indicate [ok]) I use filezilla for my ftp client. Here is my setting/configuration: Host: ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Port: -(blank, but I have tried 20 and 21 though) Server Type: FTP - File Transder Protocol Logon Type: Normal Username: (tried root and ec2-user) Transfer mode: Tried passive and active I always has this error: Status: Waiting to retry... Status: Resolving address of ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Status: Connecting to XX.XX.XXX.XX:21... Error: Connection timed out Error: Could not connect to server Have I missed any configuration/settings? EDIT After execute the /sbin/iptables -L -n Here is the result: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. EDIT: trying to grow the RAID using mdadm --grow yields mdadm: raid0 array /dev/md0 cannot be reshaped Is there any other way I can grow a RAID0 array?

  Read the article

• EDQ Technical Enablement for OPN (Prague - June 17-19)

  - by milomir.vojvodic

  Oracle Enterprise Data Quality (EDQ) Technical Enablement and Partner Training Trusted Data for Your Enterprise Applications Oracle Enterprise Data Quality helps organizations achieve maximum value from their business-critical applications by delivering fit-for-purpose data. These products also enable individuals and collaborative teams to quickly and easily identify and resolve any problems in underlying data. With Oracle Enterprise Data Quality, customers can identify new opportunities, improve operational efficiency, and more efficiently comply with industry or governmental regulation. Oracle Enterprise Data Quality is designed to serve as a very channel friendly platform to OPN.  This means that pre-built extensions, components and even complete business solutions can readily be built and shared.  This allows our customers/partners to be highly efficient in how they deploy custom business solutions, but also allows our partners to develop specialized components, domain knowledge and even complete business solutions. Training is suitable for: · Database administrators · Architects · Technical staff Objectives of the training: After completing this course, participants should: · Have an understanding of the core functionality of EDQ across profiling, auditing, transforming, parsing and matching data · Be able to describe some of the key capabilities and benefits delivered by EDQ · Be able to create and run standalone EDQ processes and jobs · Be ready to start working with data from customers and (with practice) be able to demonstrate EDQ to customers Agenda 17th June Fundamentals For Demoing (Profile, Audit, Transform and More) Profiling Auditing Transforming Writing and exporting data Jobs and scheduling Publishing, packaging and copying EDQ processes Introduction to the Customer Data Extension Pack Realtime Processing via Web Services The Server Console Run Profiles Data Interfaces Sampling Publishing metrics to the Dashboard Users and security 18th June Matching Matching overview Basic matching configuration Matching rule hierarchies Clustering Merging Reviewing possible matches Outputting Match Data Case study 19th June Address Verification Address Verification Overview Configuration Accuracy Flags Parsing Parsing Overview Phrase profiling Tailoring a CDEP Parser Base Tokenization Classification Reclassification Selection Resolution Register Here Don’t miss this FREE event. Space is limited. Oracle University V Parku 2294/4 148 00 Praha 4 17.6. – 19.6. 2014 09:00 a.m.– 17:30 p.m.

  Read the article

• alsa - sound issues on ubuntu 12.04

  - by tam_ubuuser

  i am having an sony E series laptop.i have an HDMI port .at this stage ,i have tested my sound card , which provides audio out on my laptop i.e i could hear songs .my laptop has two sound cards amd 5450 and an intel-hda(alsamixer shows that as s/pdif) . i decided to connect HDMI output to my new HD-TV.but, i could get only visuals on my TV,NO AUDIO OUTPUT ( HDMI cable works fine with win 7).my laptop has two sound cards.but i couldn't switch output to other card.( i don't know ,how to do that) i decided to update alsa. complied the following code in terminal. sudo apt-add-repository ppa:ubuntu-audio-dev/alsa-daily sudo apt-get update sudo apt-get install alsa-hda-dkms then,strangely no login sound, and no audio output on my laptop at all .then, started complied code from step1 sound troubleshooting procedure from offical ubuntu site.then, my speaker icon taskbar disappeared .obivously $aplay -l ,provided output as no soundcards detected . so , i implemented step 4 from that guide, it provides a output of all hardware devices in my laptop. *-multimedia UNCLAIMED description: Audio device product: Cedar HDMI Audio [Radeon HD 5400/6300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:f0040000-f0043fff *-multimedia UNCLAIMED description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f5e00000-f5e03fff that command displayed output name of the two cards . but , still i have no positive output on $aplay -l. so therfore, i think alsa couldn't detect my sound cards . is there solution to this problem? it could be better,if alsa would channel output from multiple sound cards ? how should install and configure alsa such that detects HDMI cable as soon i connect to my HD tv? is it possible to alsa and pluseaudio 2.0 to co-exist, if so how?

  Read the article

• Web server replica not working in other server

  - by user761076

  I have a Drupal installation (php+mysql) in a server, and I'm trying to copy this installation to another server with the same configuration, same physical and virtual path, same db configuration, etc. The thing is, in my new server I get the homepage to work, but not the inner pages, so I guess has something to do with rewrite (mod_rewrite is installed) (both .htaccess are the same). When I access http://localhost/myweb/content/mypage I get a 404 or a "Forbidden" if I uncomment this in httpd.conf (original httpd.conf does not have this entry): <Directory path/to/docs"> DirectoryIndex index.php index.html Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> Any clue? Thank you

  Read the article

• Logs being flooded from Squid for having intercepted and authentication enabled together

  - by Horace

  I have done some hefty Google'ing and I can't seem to find a single solution to this issue that I cam currently experiencing. Here is a sample configuration from squid that I have: # # DIGEST Auth # auth_param digest program /usr/sbin/digest_file_auth /etc/squid/digpass auth_param digest children 8 auth_param digest realm LHPROJECTS.LAN Network Proxy auth_param digest nonce_garbage_interval 10 minutes auth_param digest nonce_max_duration 45 minutes auth_param digest nonce_max_count 100 auth_param digest nonce_strictness on # Squid normally listens to port 3128 # Squid normally listens to port 3128 http_port 192.168.10.2:3128 transparent https_port 192.168.10.2:3128 intercept http_port 192.168.10.2:3130 As noted above, I have three ports defined, 2 of them are transparent/intercept and one is a regular http port (which I use for authentication). Which works rather well in this configuration however my logs are getting flooded of this entry authentication not applicable on intercepted requests whenever a transparent connection is made. So far, I can't seem to find any documentation that would describe how to suppress these messages ?

  Read the article

• IIS7 folder permissions

  - by Eanna

  I build a basic WCF service that I now want to host in IIS7 under Windows Server 2008 R2. I added the service as an application under the default web site but whenever i try to run the application I get the following error: HTTP Error 500.19 - Internal Server Error The requested page cannot be accessed because the related configuration data for the page is invalid. Config Error - Cannot read configuration file due to insufficient permissions The only way I can get this service working is if i choose to "connect as" the server Administrator when adding the service. the "application user (pass-through authentication)" option does not seem to work. Could anyone help me out, I've just started using IIS7 and have no idea what to do... Thanks

  Read the article

• Ubuntu apt-get install (--download-only) executed from another machine on behalf of mine

  - by Maroloccio

  I have a server on a network segment with no direct or indirect access to the Internet. I want to perform an: apt-get install <package_name> Is there a way to somehow delegate the process of downloading the required files to another machine by exporting the server configuration so as to satisfy all dependencies while running: apt-get install --download-only <package_name> Can, in effect, apt-get install read a configuration from an exported archive rather than from the local package database? Can the list of packages to be downloaded be retrieved, along with an installation script to perform the installation, instead of the actual packages? (a further level of indirection which would help me schedule this with wget at appropriate times...)

  Read the article

• Easily manage vsftpd virtual users?

  - by Phil

  I have a vsftpd server configured with many virtual users. logins are stored in a Berkeley DB file One configuration file exists for each user to define his permissions (read-only or read-write, home directory, etc.). To do that, I use the user_config_dir parameter (set in vsftpd.conf). I am wondering if it would be possible to manage these virtual users from a simple GUI (such as web interface). I have found some tools but they are limited to generic vsftpd configuration, not virtual users management. Otherwise, PAM-MySQL seems to be a good way to manage users efficiently but only username/password and logs can be stored in database, not permissions. Finally, I've found this thread, but the solution is a bit awkward... Is there any way to easily manage the vsftpd users ?

  Read the article

• Blocking popups and ads

  - by user74364

  I'm having a fight with ads, popups and tracking cookies. But i'm having some issues. Software used: Chromium 18.0.1025.168 Extensions used: Adblock Plus (Beta)1.2 AdBlock+ Element Hiding Helper1.1.9.18 Better Pop Up Blocker2.1.6 Ghostery3.0.0 With this configuration, i'm always getting this error: Warning: This extension failed to modify a network request because the modification conflicted with another extension. I know if i disable "better popup", this goes away. It's perfectly normal, due to those extensions trying to block the same things. Problem is, i can't live without all of them! Can anyone advise me about some good configuration? Can't live without adblock plus, because i hate ads. Betterpopup blocker is essential too (believe me, chrome doesn't block a lot of popups, and i have a website or 2 that can proove that.) And ghostery is a must... i can't bare the idea of being tracked all the time by some companies. So i'm kinda lost here! everything is needed, but they conflict with each other. i mean, it has to exist a perfect combination out there, i know i'm not the only one hating the privacy issues nowadays! really thankful for any tips guys

  Read the article

• Problem connecting with RDP between Mac and Win2k3 server

  - by salle55

  I have an iMac running Mac OS X 10.5.8 and the RDP Connection Client 2.0.1. http://salle.dyndns.org/misc/rdp%5Fproblem1.png When I try to connect to a Windows 2003 Server on the same network I get a dialog saying "Remote Desktop Connection cannot verify the identity of the computer that you want to connect to". Picture: salle.dyndns.org/misc/rdp_problem2.png And when I press the Connect-button in the previous dialog I get the same message in another dialog: Picture: salle.dyndns.org/misc/rdp_problem3.png I can connect to the Win2k3 server from a Vista machine, and it used to work from the Mac as well. I stopped working from the Mac after I did some configuration on the win2k3 server, removed and added the the connection in the Terminal Services Configuration: Picture: salle.dyndns.org/misc/rdp_problem4.png What do I need to do to be able to connect from the Mac again? (I have not enough reputation to post multiple links or images)

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Second virtual host on Apache redirects to root

  - by Slytherin

  I tried to setup my second virtual host , but I'm getting the default /var/www/index.html ( the one that says "It works!" ) I followed the same procedure as the first time, but this time it didn't work my configuration looks like this <VirtualHost *:80> ServerName messup ServerAlias messup.loc ServerAdmin webmaster@localhost DocumentRoot /var/www/messup ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> my hosts configuration is the following 127.0.0.1 localhost 127.0.1.1 SlytherinPC 127.0.0.1 AFS.loc 127.0.0.1 messup.loc After this , my apache wouldn't restart without any message , only saying [fail] , but stop and start worked. What am I missing ?

  Read the article

• Errors when installing updates

  - by user71613

  I am getting the following errors when installing updates. They started to appear after I upgraded my system to 12.04. Errors were encountered while processing: samba-common samba-common-bin samba grub-pc grub-gfxpayload-lists Setting up samba-common (2:3.6.3-2ubuntu2.2) ... perl: error while loading shared libraries: libperl.so.5.12: cannot open shared object file: No such file or directory dpkg: error processing samba-common (--configure): subprocess installed post-installation script returned error exit status 127 dpkg: dependency problems prevent configuration of samba-common-bin: samba-common-bin depends on samba-common (>= 2:3.4.0~pre1-2); however: Package samba-common is not configured yet. dpkg: error processing samba-common-bin (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of samba: samba depends on samba-common (= 2:3.6.3-2ubuntu2.2); however: Package samba-common is not configured yet. samba depends on samba-common-bin; however: Package samba-common-bin is not configured yet. dpkg: error processing samba (--configure): dependency problems - leaving unconfigured Setting up grub-gfxpayload-lists (0.6) ... Setting up grub-pc (1.99-21ubuntu3.1) ... perl: error while loading shared libraries: libperl.so.5.12: cannot open shared object file: No such file or directory dpkg: error processing grub-pc (--configure): subprocess installed post-installation script returned error exit status 127 Any ideas how to fix this?

  Read the article

• How to restrict ssh port forwarding, without denying it?

  - by Kaz

  Suppose I have created an account whose login shell is actually a script which does not permit an interactive login, and only allows a very limited, specific set of commands to be remotely executed. Nevertheless, ssh allows the user of this account to forward ports, which is a hole. Now, the twist is that I actually want that account to set up a specific port forwarding configuration when the ssh session is established. But it must be impossible configure arbitrary port forwarding. (It is an acceptable solution if the permitted port forwarding configuration is unconditionally established as part of the every session.)

  Read the article

< Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >