Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 224/783 | < Previous Page | 220 221 222 223 224 225 226 227 228 229 230 231  | Next Page >

• Sending a UDP message to a computer inside a network

  - by Dan

  Say I have the ip and mac address of a computer inside a network and I wish to send him a UDP message. By initializing the mac and ip addresses of the sent message to the given, when the network router recives the message he should pass it to the computer with the same mac address...right? Im asking becuase a program I write dosent seem to handle this limitation. it works great when its on the same network, but otherwise ...nada. Thanks

  Read the article

• error: "net.netfilter.nf_conntrack_acct" is an unknown key

  - by anonymous

  Hello, i have the next error when i run 'sysctl -p' error: "net.netfilter.nf_conntrack_acct" is an unknown key net.netfilter.nf_conntrack_acct = 1 net.ipv4.netfilter.ip_conntrack_max = 9527600 net.ipv4.netfilter.ip_conntrack_tcp_timeout_established = 7200 lsmod ipv6 289352 34 loop 19724 0 nf_conntrack_ipv4 19352 0 nf_conntrack 71440 1 nf_conntrack_ipv4 joydev 15232 0 evdev 14592 0 ext3 125456 3 jbd 54696 1 ext3 mbcache 13188 1 ext3 raid1 24832 4 md_mod 81700 5 raid1 thermal_sys 17728 0 Debian 5.0.8 Any idea? Thanks

  Read the article

• Connecting two servers together - How to?

  - by Chris

  Is it possible to connect two servers running for example Windows Server 2003/2008 together. For example they are seen on the network as one server with the combination of all HDD from each server? Example: \\Server1 - 1 x 1tb hdd \\Server2 - 1 x 1tb hdd I would like users of the network to be able to store their documents on both servers for load balancing. So basically a RAID between the two servers? Any help would be appreciated.

  Read the article

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• SQUID Transparent SSL proxy (no intercept)

  - by user974896

  I know how to have squid work as a transparent proxy. You put it into transparent mode then use your router or IPTABLES to forward port 80 to the squid port. I would like to do the same for SSL. Every guide I see mentions setting up keys on the squid server. I do not want squid to actually decrypt the SSL traffic then establish a connection with the server, rather I would like squid to simply forward the SSL traffic as is. The only thing I would like to do is be able to check the SSL request for any offending IPs and drop the packets if the destination is one of them.

  Read the article

• linux macvlan - stop from broadcasting hostname

  - by staticfloat

  I am trying to simulate two different computers on one box, using the macvlan module (which is awesome, by the way) but I have one small problem; When I create the macvlan Ubuntu 11.10 very helpfully starts broadcasting its hostname on both interfaces, creating an amazing amount of confusion for everything that deals with hostnames. Does anyone know how to stop ubuntu from advertising its hostname on a certain interface? Thanks!

  Read the article

• How to Solve the "Unidentified network" in Windows 7

  - by gylns

  I connect the internet through Ad-hoc network, My machine uses win7 and another uses winows xp, There's no problem when I connect the XP machine, but if i disconnect and reconnect the net, then my local network is marked as "Unidentified network",unless restart the XP machine, I don't know why?

  Read the article

• Which routers do you prefer for DD-WRT or OpenWRT?

  - by hyperslug

  I'm aware of the giant Supported Devices list. I'm wondering which ones you all prefer (e.g., support for Mega install, cheap, reliable hardware, USB port, etc.) I've used an ASUS WL-500G Premium for 1.5 years, but I've been eyeballing the WL-520gU recently.

  Read the article

• Using Credentials with network scanners

  - by grossmae

  I'm testing out both Tenable's Nessus scanner as well as eEye's Retina for scanning network devices. I am trying to supply credentials to get deeper, more accurate results, however there seems to be no difference in the results whether I supply the credentials or not. I've read the documentation and it seems like I've tried all the logical settings in the Credential options. I've submit along with usernames and passwords for many different accounts and types of accounts (both SSH Credentials and Web Application Credentials) on the devices as well as their respective domain names (when applicable). Is there possibly a good test for either (or both) scanners to tell where these credentials are being provided (if at all) and if any of them are successfully getting authentication?

  Read the article

• Picasa 3.5: how to share the tagged faces from one PC to another

  - by Eduardo Molteni

  At home, we share our photos from a server. I've been tagging the faces in Picasa 3.5 in one PC, but in the other PC the same photos needs to be retagged. Where is this info stored so it can be shared between computers?

  Read the article

• Can ping between Host and Guest, but can't acces webserver with Virtualbox

  - by Gastoni

  How come I can ping back and forth between host and guest using VirtualBox, but I can't access from the host the web server installed in the guest. I'm using a host-only network. Host Ubuntu 10.10 vboxnet0 - 192.168.56.1 ping to self, works ping to guest, works access to web server in guest, FAILS Guest Fedora 13 eth1 - 192.168.56.101 ping to self, works ping to host, works access to web server in host, works

  Read the article

• Flow of packets in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN When packet goes from router to local LAN, do it passes all the computers? Does it go to the ethernet card of every computer and those computers accept the packet based on their physical address? To which pc the packet will go first? To the nearest to the router? What happens if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this?

  Read the article

• Obtaining a DHCP IP address if static address is not available

  - by user142485

  I have seen some questions that are similar to my problem but not a good solution. Ex. User has a laptop and has a static IP address at the office. They also take the laptop off site where they also need internet. Is there a way to configure their computer so that it will obtain an IP address automatically when the configured static address is not available (without making the user go into network configuration and changing to obtain automatically)?

  Read the article

• DD-WRT Router Can't hold a connection after initial setup...

  - by AC

  Struggeling with my new DDWRT router (Buffalo WZR-HP-G300NH) configuration. I configured it using one machine while comparing the settings on my existing Linksys WRT54GL on another machine. To the best of my knowledge, I've set it up the same way as my Linksys, but DDWRT has so many other options. After configuring it, I plugged it into the modem, VOIP device & my network. I see the phones come back online. However after a few minutes, it seems I lose the outbound connection (phones die and I can't get out over HTTP). What's confusing me is it works for a few minutes, then it fails. No idea what to look for. Ideas?

  Read the article

• Why do I have only incoming traffic when copying from network source to network destination?

  - by mxp

  I have a VirtualBox VM that is located on a network share of my NAS. When I copy something from the VM's disk onto another of the NAS' network shares (so the data is visible outside the VM), the Windows 7 Task Manager shows only incoming network traffic (yellow graph). It's as if the data was only received but never sent over the network. I verified that the data arrives on the other network share. As I understand it, the data flow looks like this: +-NAS--------+ +-Win7 PC (VM Host)-+ | Share1(VM)-|>---->|-+ | | | | | | | Share2 <---|<----<|-+ | +------------+ +-------------------+ If it was like this, I would see incoming and outgoing traffic, right? What am I not getting here?

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• Mounting an nfs directory in UNIX on a system with two NICs

  - by William

  Hi, I'm trying to mount a folder located at 10.0.0.1:/pxe/ on eth1 but I'm not sure how to do this with two NICs enabled. The command mount 10.0.0.1:/pxe/ /mnt/pxe/ works fine when I only am using the one NIC the appropriate machine is on, but how can I specify to use eth1 when eth0 is also enabled? Thank you.

  Read the article

• File property information (last write time and file size) in explorer out of date by hours over netw

  - by David L Morris

  An application is running on a windows XP prof machine picking up file from a network share from another windows machine. It detects that the file has been updated (by date and time or optionally file size) and reads it for any new data. Most of the time the last write time and file size, seems to be up to date. Occasionally, this information stops being updated, even though the file is growing (intermittently during the day) with appended content, so that the last write time and file size remain fixed at some arbitrary moment. This is visible in explorer, where it shows a fixed last write time on the reading machine. Just opening the file to edit it in notepad, immediately refreshes the file properties, and the other application picks up where it left of. The file location can't be changed, nor the location of the relevant applications. Any solutions to resolve this problem?

  Read the article

• How to set up my network/bridging using Apple Airport equipment?

  - by John

  I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

  Read the article

• How can I run a game server on a computer behind a NAT, if I have another computer not behind a NAT?

  - by Macha

  My home connection is part of a large NAT, outside my control. Inside my home, my router has a NAT, under my control. I control a public facing Linux VPS with one IP address, outside my home network. Ideally, what I'd like to do is set something up so that I connect my home computer to my VPS, and after that port X on my VPS leads to port Y on my home computer, for the purposes of running a game server of a game that does not run under Linux. Is this possible?

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• VirtualBox no network access

  - by Frantumn

  I'm on a work machine, setting up a virtual ubuntu image using virtual box. After I installed the image, I can't seem to connect to the internet. If I look at network and sharing center on my host OS (W7) I see that the VirtualBox Host-Only Network reads as "no network access" How can I set it up so that it uses the same network as the host OS. UPDATE! Okay, is there a way I can tell virtual box host-only network to use a proxy script?

  Read the article

• is it possible in this case to get two IPv6 networks to communicate over the IPv4 Internet?

  - by user239167

  I have a setup of a laptop connected to a cellular IPv4 network (3G usb dongle) and PC connected to another IPv4/IPv6 network. Both have been configured to run as IPv6 routers and each has its IPv6 network. The laptop connects to the Internet via the 3G network with IPv4 address (private one and it is mostly changing) on one interface and has the other interface on AP mode providing its own private IPv6 network (2001:db8:444::/64). The PC connects to the Internet via the organization network with both public IPv4 and IPv6 addresses on one interface and has the other interface on AP mode providing its own private IPv6 network (2001:db8:222::/64). Both running Linux Ubuntu. Is it possible to get the two IPv6 network (2001:db8:222::/64 and 2001:db8:444::/64) to communicate over the IPv4 Internet? Is openvpn of any good in this case to get IPv6 traffic over IPv4-IPv4 tunnel? Thanks for helping in advance

  Read the article

< Previous Page | 220 221 222 223 224 225 226 227 228 229 230 231  | Next Page >