Search Results

Search found 7651 results on 307 pages for 'execution plan'.

Page 226/307 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• Windows 7: Dual Monitor Issue

  - by sdoca

  I have a Dell laptop with a docking station and two external monitors hooked up. I'm running Windows 7 64 bit. Originally, the two monitors were the same - Dell 1908FP. I have replaced one of them with an HP LA2405. I have set the HP 24" (1920 x 1200 connected via DVI port) as montior 1 and extended to use the Dell 19" (12080 x 1024 connected via VGA port) as monitor 2. I have set my power plan so that when the laptop is plugged in, it will turn the monitors off after 10 minutes, but it will not put my laptop to sleep. However, now that I have the HP monitor, when I unlock my laptop and the monitors come back on, all my windows are resized and shifted to the top left corner of the HP monitor as if they had been resized for display on the smaller Dell monitor. A co-worker has the exact same laptop and monitor configuration but doesn't experience this issue, so I figure there's some configuration that's different but we can't find it. I haven't been able to find any mention of a similar problem doing an internet search, but I'm not really sure what terms to use in my search. Anybody have any suggestions as to what may be causing the issue? OS setting? Monitor setting? EDIT: My laptop is using the Intel Graphics and Media Control Panel/drivers.

  Read the article

• Replicated filesystem and EC2 MySQL

  - by El Yobo

  I'm currently investigating migrating our infrastructure over to run on Amazon's EC2 and am trying to figure out the best way to set up a MySQL service. I'm leaning towards running our own MySQL instances, rather than going with Amazon's RDS, but am still considering the best approach for performance and cost on the instance itself. In order to have persistent data, the MySQL data needs to be on an EBS volume (with some form of striped RAID, e.g. RAID0 or RAID10) to improve persistence. However, EBS IO is limited by the network interface (gigabit, so a theoretical maximum of 128 MB/s), while the ephemeral volumes have no such problem. I did see a suggestion for running two MySQL servers on an instance, with a master running on the ephemeral disk (which we would also RAID) and a slave storing changes to an EBS volume, but this has some additional overhead and complexity (two servers). What I was imagining is using some form of replicated file system such that I could have a filesystem on top of a RAID0 of ephemeral volumes to maximise performance all changes from the above immediately replicated to another RAID1 volume backed by multiple EBS volumes to ensure no data loss The advantages of this would be best possible IO performance for the DB server; no network delay in IO decreased IO on EBS volumes (as all read IO will be done on the ephemeral volumes) so decreased cost good data security, as it's backed onto redundant EBS volumes However, I haven't seen an appropriate system to replicate all changes from one volume to the other; is there a filesystem, or any other approach, which will do this? The distributed file systems, e.g. GlusterFS, DRBD etc seem to focus on replicating disks between servers, can they be set up to do what I'm interested in here? I also haven't seen anything about other's taking this approach. Do I have a solution in need of a problem here (i.e. is performance good enough, so this whole idea is redundant)? Is there some flaw in the plan?

  Read the article

• File permissions on web server

  - by plua

  I have just read this useful article on files permissions, and I am about to implement a as-strict-as-possible file permissions policy on our webserver. Our situation: we have a web server accessed through sftp by different users from within our company, and we have the general public accessing Apache - sometimes uploading files through PHP. I distinguish folders and files by their use. So based on this reading, here is my plan: All people who need to upload files will have separate users. But all of those users will belong to two groups: uploaders, and webserver. Apache will belong to the group webserver. Directories Permission: 771 Owner: user:uploaders Explanation: to access files in the folder, everybody needs to have execute permission. Only uploaders will be adding/removing files, so they also get r+w permission. Files within the web-root Permission: 664 Owner: user:uploaders Explanation: they will be uploaded and changed by different users, so both owner and group need to have w+r permissions. Webserver needs to only read files, so r permission only. Upload-directories Permission: 771 Owner: user:webserver Explanation: when files need to be uploaded, Apache needs to be able to write to this directory. But I figure it is safer to change the owner to webroot, thus giving Apache sufficient privileges (and all uploaders also belong to this group and will have the same permissions), while safeguarding from "others" writing to this folder. Uploaded files Permission: 664 Owner: user:webserver Explanation: after uploading Apache might need to delete files, but this is no problem because they have w+r permission of the folder. So no need to make this file any more accessible than r access for group. Being not an expert on file permissions, my question is whether or not this is the best possible policy for our situation? Any suggestions welcome.

  Read the article

• i7-980X at 70% speed

  - by Buxley

  Hi we bought a nice computer to use to solve optimization problems. Intel i7-980X@3,33 GHz with 12 GB of Team Group 1600 MHz DDR3 RAM. When we use Gurobi the computer uses all 12 cores at maximum in the beginning of the solve. However after a while (about 8 hrs) it all cores jump between 65 and 85% When I solve the same models on an i7 930 all cores are at a near 100% level even after longer solution times. We first thought that the Hard disk was the bottleneck since Gurobi writes out nodefiles after the memorylimit is used. However since the new computer have 12 GB of RAM we put the memorylimit to 7 GB so the solver only used the RAM and still with the same performance in the processor. Any ideas about the bottleneck? As I said earlier it works at 100% for the first hours or so . Thanks very much for any answers! Our plan was to overclock it but we can't even get it to work at normal speed yet!

  Read the article

• Outbound ports to allow through firewall - core requirements

  - by dunxd

  This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support email and web access, which I know everyone will need: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working? I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

  Read the article

• Upgrade to Q9550 or i7 920 on a budget?

  - by evan

  I'm planning to upgrade my computer and torn between maxing out the system I have or investing in the X58 architecture. I'm currently using a E6600 Core 2 Duo with 4GB of RAM (800mhz) on an Asus PK5-E motherboard which I built two years ago. My original plan was that one day I'd upgrade machine to 8GB (1066mhz, the max the PK5-E allows) and to the Core 2 QuadQ9550 to give the machine a good four years of life. However, that was before the i7 came out. I use my computer mainly for software development , which I do inside Virtual Machines, and the i7 seems ideal for that because it no longer is limited by the speed of the FSB? And when I looked into it, getting 8GB DDR3 RAM isn't much more expensive than the 8GB of DDR2 and the i7 920 is comparable in price to the Q9550, which doesn't make much sense to me? So the question is it worth swapping the motherboard out for around $250 and upgrading all three components or using that money on SSD or 10rpm drive for the existing system's OS/Apps/Virtual Machine drive? Or just put the $250 towards a completely new machine in a year or two? Would the i7 really give that much of boost compared to the Q9550 for what I'd be using it for? Thanks in advance for your input!!!

  Read the article

• How to route outbound traffic to specific domain "XYZ.org" via a specific NIC or public/static IP?

  - by user139943

  Within the next week or so, I'll be setting up an AT&T U-verse modem with 5 usable static public IP addresses. I plan to register a domain name to 1 of the 5 static IPs (remaining 4 unregistered), and run a website from a single server setup in my home LAN. I'll skip the long winded reason why, but I need to somehow route outbound traffic (originating from my server) destined for one public domain (i.e. http://www.sample.org) through one of the UNREGISTERED static IP addresses ONLY. Basically, I want this public domain to see connections coming from an IP address and not my domain name. If it makes it easier, this can apply to all outbound traffic from my server as long as it doesn't impact users browsing my website! Inbound connections should go through the domain name / registered public IP. Can I accomplish this with my single server with one or multiple NICs? Do I need multiple servers and set one up as a proxy? Please help as my background is in software and not networking, and I don't think I can accomplish this at a software level (e.g. Java). Thanks.

  Read the article

• HP DL380 G3 2U For Basic Web Server in 2012

  - by ryandlf

  I have an opportunity to pick up a used HP DL380 G3 2U for $100. I'm looking for a basic entry level web server that I can host a small - medium size website on and more or less learn the ins and outs of running my own web server before I bite the bullet and spend a couple grand on a server. The specs are: Dual (2) Intel Xeon 2.4GHz 400MHz 512KB Cache 4GB PC2100 ECC Registered Memory 6 x 72GB 10K U320 SCSI Hard Drives Smart Array 5i RAID Controller Redundant Power Supplies DVD/Floppy, Dual Intel GB NIC's, USB Or would I be better off spending a couple hundred bucks on something like: this new HP Seems like the only major difference is SATA and a bit of storage, but I will likely be implementing a separate storage system of some sort anyways. I guess it also wouldn't hurt to mention that I plan on running a linux server distro, so would the hardware be likely to support linux with a system that is 4 generations old? I don't mind spending a couple hundred extra dollars if its a better solution, but as mentioned previously I am simple looking for a server to learn on and probably use for a year or so while I put together a small - medium size website.

  Read the article

• Setting up test an dlive enviornment - how?

  - by Sean

  I am a bit new to servers and stuff so had a question. I have my development team working on my website. They are in different countries and currently they put all the work live on the test site. But the test site is open to anyone who knows the URL. It is behind a directory but this effects my QA process because i cannot use the accurate URL structures to prevent the general public from seeing it. So what I want to do it: Have my site live on the net but only for me and my team, so like an internal network. Also I will need to mirror this to my live site when i put it live. So i guess this is something like setting up a staging and live environment. So how to do it and are both environments on the same physical server or do i need to buy two servers? And if i setup a staging environment how will i access it and my team since we are all spread out so i assume we need to log into something to access it? What about the URL - do i need a different URL for the test site or can i use the same live url for the test site? I plan to get a dedicated server + CDN for my site.

  Read the article

• Truecrypt and hidden volumes

  - by user51166

  I would like to know the opinion of some users using (or not) the hidden volume encryption feature of Truecrypt. Personally until now I never used this feature: on Windows I encrypt the system drive as a standard volume, on GNU/Linux I encrypt using LUKS which is Truecrypt's equivalent to standard volume. As for data I use the standard volume approach as well. I read that this feature is nice and all, but it isn't really used by most people. Do you use it or not? Why? Do you only store inside it VERY sensible data or what else? Because technically speaking doing a hidden volume which has (almost) the same size as the outer one doesn't make sense: the outer volume will be encrypted but no data will be on it, which will appear very strange. So not only one has to plan which data store where, but has even to remember each time to mount the outer volume with hidden volume protection (otherwise there'll be a data loss when writing to it). It's a bit messy: hidden OS + outer OS + outer volume + hidden volume = 4 partitions :( Similar question about the hidden operating system (which I don't use [yet]).

  Read the article

• i7 x980 at 70% speed

  - by Buxley

  Hi we bought a nice computer to use to solve optimization problems. intel i7 X980@3,33 Mhz with 12 Gb of Team Group 1600 MHz ddr3 Ram. When we use Gurobi The Computer uses all 12 cores at maximum in the beginning of the solve. However after a while (about 8 hrs) it all cores jump between 65 and 85% When I solve the same models on an I7 930 all cores are at a near 100% level even after longer solution times. we first thought that the Harddisk was the bottleneck since Gurobi writes out nodefiles after the memorylimit is used. However since the new computer have 12 GB of Ram we put the memorylimit to 7 GB so the solver only used the RAM and still with the same performance in the processor. Any Ideas about the bottleneck? As I said earlier it works at 100% for the first hours or so . Thanks very much for any answers! Our plan was to overclock it but we can't even get it to work at normal speed yet!

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• Installing a new Motherboard in a HP xw6200 case

  - by thing2k

  I have a HP xw6200 Workstation, that is rather long in the tooth, and with 2 physical CPUs, it is quite inefficient. So, the plan was to upgrade the internals. Nothing special: AMD Athlon II X4 640 ASUS M4A78KT-M LE (mATX) 2x 2GB DDR3 1333MHz RAM. 3p under my £150 budget The issues: The pin connector for the front panel isn't a good fit, but I can trim it to size. The PSU has a 8-Pin Power connector, unsurprisingly, the new board has a 4 pin socket. The pins do line up, but I would have to cut it in half to fit. Finally, due to the weight of heat-sinks, they are screwed directly into the case. It turns out that these screws also lock the motherboard in place. As to remove it, you remove the heat-sinks, slide the motherboard across and lift it out. I tested the new board for fit, and while it slots in fine, it's not secure. There is nowhere to screw the board down, it is just held in place with plastic standoffs. The only idea I had, was to wedging something between the side of the motherboard and part of the case. Any suggestions?

  Read the article

• VOIP and internet connection speeds [cable vs. fiber]

  - by microchasm

  Our office is migrating to IP telephony. We have less than 10 employees that will be using the phones. We currently have cable internet, and they just bumped the speeds: There is a data center that was just recently built in our building, and we were considering co-lo'ing there in the near future. As a result, they offered us access to their triple-redundant internet, but it's quite expensive. They are offering 3mbps committed with up to 10mbps burst for $250/month (discounted). We pay ~$120 for our cable (which the plan was to keep--at least for TV). I want the phone system and LAN to be as separate as possible. Was thinking about keeping the cable for LAN, and using the other connection for the phones (until I saw the price). Now I'm thinking it might make sense to add on to our existing cable setup, and change our phone to only have DSL as a backup for the cable. Is there any real benefit to the fiber? Especially for the price? Any other suggestions or ideas? Thanks.

  Read the article

• environment variables generated by at command

  - by Jordan Arseno

  I'm inspecting /var/spool/cron/atjobs/a001cf01570e44 with cat, after running the at command from PHP using exec(). It looks like at has prepended the script with lots of APACHE environment variables. #!/bin/sh # atrun uid=33 gid=33 # mail www-data 0 umask 22 APACHE_RUN_DIR=/var/run/apache2; export APACHE_RUN_DIR APACHE_PID_FILE=/var/run/apache2.pid; export APACHE_PID_FILE PATH=/usr/local/bin:/usr/bin:/bin; export PATH APACHE_LOCK_DIR=/var/lock/apache2; export APACHE_LOCK_DIR LANG=C; export LANG APACHE_RUN_USER=www-data; export APACHE_RUN_USER APACHE_RUN_GROUP=www-data; export APACHE_RUN_GROUP APACHE_LOG_DIR=/var/log/apache2; export APACHE_LOG_DIR PWD=/home/jordanarseno/webroot/public_html/myapp; export PWD cd /home/jordanarseno/webroot/public\_html/myapp || { echo 'Execution directory inaccessible' >&2 exit 1 } curl -k http://localhost/myapp/crons/this_action/3 The last line is the only real command I sent along with at via stdin. What is the purpose of these variables? Where is this procedure stored?

  Read the article

• How To Completely Move Users/Program Files/Program Files (x86)/ProgramData (Folders) To Another Partition(s) On Windows 8?

  - by Enigma83

  I am attempting to move folders Users Program Files Program Files (x86), ProgramData (at the root of the C drive) to at least 2 other partitions, preferably on a fresh install. I have read that there are methods for doing this post-install, but it seems like it would be a bit more tedious to do things that way. I want to move the 2 Program Files folders to another partition on the same HDD, and Users/ProgramData will go to yet another partition on same HDD. I have done a bit of research on this, read up on some things that involved booting into Audit Mode, using the RoboCopy command to copy folders via booting into my Windows 8 USB drive, creating NTFS junctions/symbolic links, Registry edits, as well as accomplishing this automatically by creating an auto-attend file which Windows Setup processes automatically before the user is ever booted in for the 1st time. I tried this morning and now have a basic installation in which programs like Internet Explorer fail to open, certain files can't be found/opened (even if I click on them directly), an example is Regedit. Also, I can't run the Command/DOS (CMD) prompt as Administrator (or otherwise, as any other user), can't activate the real Administrator account or open any of the Administrative Tools (despite having added them to my Start Screen). So far I have only tried RoboCopy-ing Program Files and Program Files (x86) so far, creating junction points for them, and editing the Registry in the relevant locations. This is what I'm left with now. I also found the following blog article which describes how to do this for Windows 7 So, where should I go from here and where can I find more information? And how can this be done without disabling the Metro apps, which I've read will stop working if you move ProgramData. Once I have everything moved, where do I install programs to? Do I tell them to install to C:\Program Files\Program Files (x86) or to the junctioned/symbolic-linked partition/drive? I plan to test in VMware virtual machines from here on until things are working correctly, while using a baseline default install for daily tasks.

  Read the article

• Windows 7 does not detect my new hard drive?

  - by jasondavis

  I just built a really nice new PC. Some specs... Intel i7-930 CPU ASRock Extreme X58 motherboard with sata 3 and USB 3.0 12gb of G-Skill DDR3 RAM 80gb Intel G2 Solid state drive for Windows 7 and other programs to run on Windows 7 Pro 64bit OS 2 1gb grapghic cards for 4 monitor support Thats the main components. Well today my new 1tb western digital hard drive came which I plan to use for data to preserve the life of my SSD (hopefully). I hooked up it's sata power input and then hooked up it's sata data cable to a sata 2 port on my motherboard, I boot windows 7 and go into my computer and the drive is not showing up with my other drives. I then re-boot again and check again, no luck. I then shut down the PC and open the case back up, I then check my connections and they all look good. I then boot up and I can see the new HD is on and spinning. I then go into my BIOS settings to see if it registers there and it DOES! It shows I have a WD 1tb hard drvie on sata 2 port 6. So I am at a loss of why it is not showing up as an option in windows? Windows acts as if the drive is not there. Please help

  Read the article

• What are secure ways of sharing a server (ssh+LAMP) with friends?

  - by Bran the Blessed

  What is the best way to share a virtual server with friends? More precisely, I have the following assets: A virtual private server (Debian Lenny) with root access for myself, running... SSH apache2 mysql Some unused disk space Some friends in need of hosting The problem I would now like to do the following: Hosting one or several domains per friend My friends should have full access to their domains, including running PHP scripts, for example My friends should not be able to poke around in other directories The security of my server should not be compromised by faulty PHP scripts To clarify: I do trust my friends in the sense that they are not trying to do something evil with their access. I just do not trust the programs they are going to run. So, what are your recommendations for establishing such a scenario? Partial solution I already came up with the following plan: Add chrooted SSH users for my friends Add Apache vhosts per user (point the directories to subdirectories of the homedirectories, i.e. /home/alice/example.com, /home/bob/example.net, etc. But how can I enforce a chroot-like environment for the scripts they are running within these vhosts? Any pointers would be appreciated.

  Read the article

• Outbound ports to allow through firewall

  - by dunxd

  This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support commonly required resources: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working. I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• OpenOffice Vs Microsoft Office 2007/2010

  - by Moody Tech

  I have been asked to summarise the pros and cons in connection with the choices between Microsoft Office Vs OpenOffice. I have a broad idea of what needs to be said. However I would like to open a discussion here and have a single place to go to when the time comes to give the summary to management. There are obvious points of contention: For me the lack of compliance with Group Policy is a major concern [Default save location/visibility of C:/Visibility of files and folders on the HDD] However I am sure that functionality and compatibility will be the prime mover. We are looking at making major savings by reducing our commitment to Microsoft licensing. So what are your experiences? What happens when there are no direct equivalents? [Word has a close match in OpenOffice, but a database solution match is not as close, neither is an Outlook [connecting to Exchange Server and downloading all calendars, shared calendars, scheduled events, for Exchange will still exist after the move to OpenSource solutions] In summary then: What do you see as: The benefits of this plan? How do you see the problems being manifest? Discuss.... Many thanks.

  Read the article

• Make call with alternate provider if NOANSWER

  - by adaptive

  I have two voip providers, one free an the other paid. The free provider only allows local calls to certain area codes, so I need to fall back to the the paid provider if a call fails. At the moment, I have the following context in my extensions.conf file: [globals] ; freephoneline.ca PRIMARY_PROVIDER=fpl ; voip.ms SECONDARY_PROVIDER=voipms [local] exten => _NXXNXXXXXX,1,Set(CALLERID(name)=${OUTGOING_NAME}) exten => _NXXNXXXXXX,n,Dial(SIP/${EXTEN}@${PRIMARY_PROVIDER}) exten => _NXXNXXXXXX,n,Set(CALLERID(num)=${OUTGOING_NUMBER}) exten => _NXXNXXXXXX,n,Dial(SIP/1${EXTEN}@${SECONDARY_PROVIDER}) exten => _NXXNXXXXXX,n,Hangup() I checked the logs and noticed that the free provider responds with NOANSWER if a call is not allowed (Even though it plays a message). What I want is to: Try calling the ${PRIMARY_PROVIDER} first. If NOANSWER is returned by provider (not that the callee did not answer), then call with ${SECONDARY_PROVIDER} How can I modify my dial plan to get the desired results? EDIT : The primary provider is freephoneline.ca, and I'm using asterisk v1.8.2.3-2

  Read the article

• Cannot Install Windows 7 SP1 (64-bit)

  - by Clever Human

  I have tried every way I know how to get Windows 7 SP1 to install. It fails every time. Below is what looks like the relevant contents of the CBS.Log file. If there are further details that would help or more information I can gather, I will get it. 2011-08-15 10:32:52, Info CBS Startup: Package: Package_for_KB976902~31bf3856ad364e35~amd64~~6.1.1.17514 completed startup processing, new state: Installed, original: Installed, targeted: Installed. hr = 0x80070490 2011-08-15 10:32:52, Info CBS WER: Generating failure report for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, status: 0x80070490, failure source: CBS Other, start state: Partially Installed, target state: Installed, client id: SP Coordinater Engine 2011-08-15 10:32:52, Info CBS Failed to query DisableWerReporting flag. Assuming not set... [HRESULT = 0x80070002 - ERROR_FILE_NOT_FOUND] 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml.bad to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS SQM: Reporting package change completion for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, current: Partially Installed, original: Partially Installed, target: Installed, status: 0x80070490, failure source: CBS Other, failure details: "(null)", client id: SP Coordinater Engine, initiated offline: False, execution sequence: 517, first merged sequence: 517 2011-08-15 10:32:52, Info CBS SQM: Upload requested for report: PackageChangeEnd_Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, session id: 101457924, sample type: Standard 2011-08-15 10:32:52, Info CBS SQM: Ignoring upload request because the sample type is not enabled: Standard I have downloaded the service pack and ran it from the EXE, I have installed it from Windows Update, I have ran all the "troubleshooting" trouble shots I could find. Nothing has worked so far. Any advice would be appreciated.

  Read the article

• How do I remove a printer connection without the user's intervention?

  - by 1.618

  Here's the situation: We're replacing 11 printers with newer models, and we'll be installing them on our print server and sharing them out. The plan is to share the new printers under different names than the ones they're replacing, and un-share the old ones. So I need to come up with a way to remove the client connections to old printers automatically. Clients are mostly Windows 7 with a few XP. My first idea was to call prnmngr.vbs from the login script to remove each old printer explicitly by name. The problem is that some users don't log out when they're done for the day, so I can't count on their login script running before they next need to print. I could remotely run prnmngr.vbs using SCCM, but if it's not 'impersonating' the user, I don't think it will remove their printers. Any ideas? Could I lookup how to access WMI using c# code and write a "trojan" to remove specific printers without requiring the user to do anything? (I'm only half joking). I'm open to any suggestion! Thanks!

  Read the article

• Is there an simple but good To Do Manager app for the Mac?

  - by Another Registered User

  Every morning I think about what I am going to do today. So I take a paper and start to write things like: [ ] Call Mr. XYZ [ ] Answer Support E-Mails [ ] Reduce website header height by 20 px [ ] Create new navigation bar icons And every time I'm done with something, I paint a checkmark in this square. On paper. It would be fun to have something like this as an application. But I don't want a heavy project management tool or integration with email. It should be like download, install, use without fat configuration and steep learning curve. usually I don't schedule my to do's, I just write down every day what I want to accomplish today. For my experience it doesn't make sense to plan what to do next week, because next week everything looks totally different. Would be cool if such a simple utility exists. At the moment I try just using textEdit and deleting rows which are done. With a nice interface, this would be much more fun.

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >