Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 227/391 | < Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >

• 2 Computers, same network, different outgoing speeds when uploading to internet?

  - by user117339

  I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

  Read the article

• Is it possible to cause artificial network packet loss or latency?

  - by nbolton

  I'm trying to reproduce some issues on a deployed application where the MSSQL server and client are running in two separate machines. I think there may be network issues between the two machines, so I'd like to try and reproduce these conditions on two Hyper-V virtual machines (on the same virtual server). Of course, the network for these virtual machines is "local" so it's actually far from the conditions in a live environment. Is there a program I can run on either virtual machine which will degrade the network performance? Or maybe any other work arounds? For example, one way to reproduce the conditions may be to run the VMs on separate Hyper-V servers in geographically dispersed locations (so the SQL traffic goes over VPN or something) -- but this is a little long winded I think. There must be a simpler way.

  Read the article

• Two domains accessing same folder

  - by Liam Quinn

  I've just taken a new role in a school and am still familiarizing myself with their network, how ever I have recently been given a task and I'm having a little trouble finding out the fundementals of it. I have an admin network/domain 10.49.x.x and a classroom network/domian 192.168.1.x both connect to a Proxy server 10.49.202.231/192.168.1.51. Each domain has it's own shared folders as you'd expect, files and software installs etc, how ever there is a folder "staff" on the classroom network that all the teachers on the classroom network can access. The users on the admin network would like to access this same folder. How do I go about making this happen?

  Read the article

• VirtualBox Port Forward not working when Guest IP *IS* specified (while doc says opposite)

  - by Patrick

  Trying to port forward from host (Mac OS X) 127.0.0.1:8282 - guest (CentOS)'s 10.10.10.10:8080. Existing port forwards include 127.0.0.1:8181 and 9191 to guest without any IP specified (so whatever it gets through DHCP, as explained in the documentation). Here is how the non-working binding was added: VBoxManage modifyvm "VM name" --natpf1 "rule3,tcp,127.0.0.1,8282,10.10.10.10,8080" Here is how the working ones were added: VBoxManage modifyvm "VM name" --natpf1 "rule1,tcp,127.0.0.1,8181,,80" VBoxManage modifyvm "VM name" --natpf1 "rule2,tcp,127.0.0.1,9191,,9090" And by "non-working", I of course mean not listening (as a prerequisite to forwarding): $ lsof -Pi -n|grep Virtual|grep LISTEN VirtualBo 27050 user 21u IPv4 0x2bbdc68fd363175d 0t0 TCP 127.0.0.1:9191 (LISTEN) VirtualBo 27050 user 22u IPv4 0x2bbdc68fd0e0af75 0t0 TCP 127.0.0.1:8181 (LISTEN) There should be a similar line above but with 127.0.0.1:8282. Just to be clear, this port is listening perfectly fine on the guest itself. And when I remove the guest IP (i.e., clear the 10.10.10.10) the forward works fine, albeit to eth0 (not eth1 where I need it). I can tcpdump and watch the traffic flow back and forth. And yes, I've disabled iptables entirely while testing -- it's not getting blocked anywhere on the guest. As VirtualBox writes in their documentation, you are required to specify the guest IP if it's static (makes sense, no DHCP record it keeps): "If for some reason the guest uses a static assigned IP address not leased from the built-in DHCP server, it is required to specify the guest IP when registering the forwarding rule:". However, doing so (as I need to), seems to break the port forward with nary a report in any log file I can find. (I've reviewed everything in ~/Library/VirtualBox/). Other notes: While I used the above command to add the third rule, I've also verified it showed up correctly in GUI and then removed/re-added from there just to make sure). This forum link -- while very dated -- looks somewhat related in that a port forward to a static IP was not appearing (perhaps they think due to lack of gratuitous arp being sent for host to know IP is there/avail?). Anyway, what gives? Is this still buggy? Any suggestions? If not, easy enough workarounds? What's interesting is that this works perfectly fine on another user's Mac, however he's running a slightly older version (4.3.6 v. 4.3.12).

  Read the article

• How can one restrict network activity to only the VPN on a Mac and prevent unsecured internet activity?

  - by John

  I'm using Mac OS and connect to a VPN to hide my location and IP (I have the 'send all traffic over VPN connection' box checked in teh Network system pref), I wish to remain anonymous and do not wish to reveal my actual IP, hence the VPN. I have a prefpan called pearportVPN that automatically connects me to my VPN when I get online. The problem is, when I connect to the internet using Airport (or other means) I have a few seconds of unsecured internet connection before my Mac logs onto my VPN. Therefore its only a matter of time before I inadvertently expose my real IP address in the few seconds it takes between when I connect to the internet and when I log onto my VPN. Is there any way I can block any traffic to and from my Mac that does not go through my VPN, so that nothing can connect unless I'm logged onto my VPN? I suspect I would need to find a third party app that would block all traffic except through the Server Address, perhaps Intego Virus Barrier X6 or little snitch, but I'm afraid I'm not sure which is right or how to configure them. Any help would be much appreciated. Thanks!

  Read the article

• Access Configuration Page of Modem (in bridge mode) through router

  - by Ujjwal Singh

  Given the Network Configuration: Internet (121.243.x.y/27) | (121.243.x.z) Static : Public Global IP Modem Bridge Mode | WiMAX (192.168.1.1/24) +169.254.1.1/24 : Modem Configuration Page | (192.168.1.2) Router DLink DIR 615 | Ethernet + WiFi (192.168.0.1/24) | Local network (192.168.0.2) Workstation Ethernet | no WiFi Is there any way, maybe using Routing Tables, to access the Modem configuration page at 169.254.1.1 from my local network, using a Windows 7 PC? Note that the modem is currently able to display its configuration page at 169.254.1.1, i.e. even while it is in bridge mode.

  Read the article

• Losing network connection after VPN disconnects

  - by Tanja Allito

  I use tunnelblick and OpenVPN on the mac, but when I choose to disconnect from the VPN I lose all network connectivity and have to reboot to get back online. Is there a way to get a new IP or something, without having to reboot?

  Read the article

• Everytime I ping my server, it is pinging localhost instead?

  - by esac

  I recently setup a new server for use with SQL. When I tried to connect via SSMS remotely, it failed. When I pinged it, it is pinging localhost, what is going on here? Please let me know if more details will help. It is Windows Server 2008. C:\>ping 0x7F000001 Pinging 127.0.0.1 with 32 bytes of data: Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms

  Read the article

• Determining the State of a User using their Hostname

  - by PhpMyCoder

  Not sure if this is the right SE site. I figured this question doesn't belong on SO, but if you think it doesn't belong here either, I apologize. I've been looking into determining the location, specifically the state, of a user accessing my website. One of the options I've known about for a while is the GeoIP City Database, however this isn't the most cost effective solution and I'm cheap so I was looking for a less expensive way. Something that occurred to me was that my state was in the public hostname assigned to me by Comcast: (Dash Separated IP).hsd1.ma.comcast.net Could it be possible that other ISPs follow this same pattern of inserting the state abbreviation into their users' hostnames? I've been looking around for a list of hostnames for other ISPs, but I haven't found anything. Can anyone verify that this holds true for other major ISPs?

  Read the article

• Cant get squid proxy to work

  - by danielgratz

  i need squid proxy on my centos server. But i just can't get it to work. I did yum install squid. Here is my squid.conf file (i removed all comments): acl all src 0.0.0.0/0.0.0.0 acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl to_localhost dst 127.0.0.0/8 acl SSL_ports port 443 acl Safe_ports port 80 acl Safe_ports port 21 acl Safe_ports port 443 acl Safe_ports port 70 acl Safe_ports port 210 acl Safe_ports port 1025-65535 acl Safe_ports port 280 acl Safe_ports port 488 acl Safe_ports port 591 acl Safe_ports port 777 acl CONNECT method CONNECT acl our_networks src 192.168.1.0/24 192.168.2.0/24 http_access allow our_networks http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access deny all icp_access allow all http_port 3128 hierarchy_stoplist cgi-bin ? access_log /var/log/squid/access.log squid acl QUERY urlpath_regex cgi-bin \? cache deny QUERY refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern . 0 20% 4320 acl apache rep_header Server ^Apache broken_vary_encoding allow apache coredump_dir /var/spool/squid Then i just put my server's public ip and port 3128 into my web browsers proxy settings... but it isn't working i can't visit any website. Please help. Thanks.

  Read the article

• Manually forcing TCP connection to retry

  - by Vi

  I have a TCP connection (SSH session to some computer for example) Network suddenly goes down and drops all packets (disconnected cable, out of range). TCP resends packets again and again, retrying with increasing delays. I see the problem and plug the cable back (or restore network somehow). TCP connection finally successfully resends some packet and continues. The problem is that I need to wait for a some timeout on point 5. I want to use my opened SSH session now and not wait for 5-10 seconds until it finds out that connection is working again. How to force all TCP connections to resend data without now in GNU/Linux?

  Read the article

• Can I connect two routers to one switch?

  - by vanneto

  I want to connect two routers to a switch which will then be connected to a modem. Now as far as I know a switch does not do network translation and this won't work with one IP address. So I bought two addresses at my ISP. Attached is a simple schematic that explains what I want to do. Is there any additional configuration needed on either of the routers (Linksys WRT54GL) to make this work or will it "Just Work"?

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• Random timeout now and then

  - by KenavR

  Maybe this is a to generic question, but since we have this issue for quite a while now, I give it a shot. We have some applications which use HTTP for the connection between the client (website or fat-client) and the server. The Computer who runs this applications is in a Network behind a firewall and a proxy, the server isn't inside the same network. The problem is that every now and then the https Request times out and depending on the Client the Application "hangs" or does some other funky stuff. The problem is definitely inside our network, because if i try the applications outside our network it works fine. Can you give me a hint where i can most likely find the problem?

  Read the article

• Only receiving one document at a time from new web server.

  - by Robert Kuykendall

  We're trying to move our internal ticketing system from a Microsoft Small Business Server in the server closet to a Rackspace Cloud Server. The install is Fedora 11 LAMP, and should be default out of the box, except for the vhosts appended to the bottom of the httpd.conf. The new server is suffering from crippling load times, and watching the page load in Firebug it's easy to see the problem occurring, but I can't figure out the cause. Here is the [old server] (http://rkuykendall.com/uploads/old.server.png). I was expecting something like this, but a little slower since it was no longer hosted locally. Instead, the [new server] (http://rkuykendall.com/uploads/new.server.png) appears to only serve one file at a time. Here's another example of this [staircase load time effect] (http://rkuykendall.com/uploads/staircase.png) and another very clear example of the [staircase effect] (http://rkuykendall.com/uploads/staircase2.png). I talked to some guys on Freenode #httpd with no luck. I created a duplicate server to play with, and also created a fresh server with Fedora Core 13 and moved over just the database and web files with no luck. Any suggestions? ( image links disabled due to n00b-spam-restrictions )

  Read the article

• How should my CAT6e cable be terminated? No pairs?

  - by user231465

  I have just bought 60 meters of CAT6e cables, sold as "4 pair UTP RJ45". I have looked at various videos on Youtube but I cannot determine the correct wiring. all the colors of the cable I saw there are different from mine. Mine is untwisted, and it is not color coded. I have 8 pin connectors all of a single color. How should I wire this cable? EDIT THE PACKAGE DOES SAY TWISTED but they are not (twisted).

  Read the article

• OpenVPN: Single certificate authority, multiple VPNs

  - by darwish

  The company in which I work has a single site (I'll refer it as "Site A"). There are several private networks within site A. We have a running instance of OpenVPN which allows some employees to connect to one of the private networks in site A. We're planning to extend our facilities to another site (which I'll refer as "Site B") and we wish to connect both sites using OpenVPN. The VPN which will connect sites A to B will be a trunk link, meaning it will have access to all networks. If we use the same certificate authority for both VPN servers, this will allow the employees, which can only to one of the private networks within site A, to connect to the site-to-site link, which will give them access to all networks. Off course this is undesirable. Using 2 different certificate authorities seems like the obvious solution, but it doesn't feel right. I wounder if there's a way to maintain permission control within a single certificate authority.

  Read the article

• Troubleshooting Network Speeds -- The Age Old Inquiry

  - by John K

  I'm looking for help with what I'm sure is an age old question. I've found myself in a situation of yearning to understand network throughput more clearly, but I can't seem to find information that makes it "click" We have a few servers distributed geographically, running various versions of Windows. Assuming we always use one host (a desktop) as the source, when copying data from that host to other servers across the country, we see a high variance in speed. In some cases, we can copy data at 12MB/s consistently, in others, we're seeing 0.8 MB/s. It should be noted, after testing 8 destinations, we always seem to be at either 0.6-0.8MB/s or 11-12 MB/s. In the building we're primarily concerned with, we have an OC-3 connection to our ISP. I know there are a lot of variables at play, but I guess I was hoping the experts here could help answer a few basic questions to help bolster my understanding. 1.) For older machines, running Windows XP, server 2003, etc, with a 100Mbps Ethernet card and 72 ms typical latency, does 0.8 MB/s sound at all reasonable? Or do you think that slow enough to indicate a problem? 2.) The classic "mathematical fastest speed" of "throughput = TCP window / latency," is, in our case, calculated to 0.8 MB/s (64Kb / 72 ms). My understanding is that is an upper bounds; that you would never expect to reach (due to overhead) let alone surpass that speed. In some cases though, we're seeing speeds of 12.3 MB/s. There are Steelhead accelerators scattered around the network, could those account for such a higher transfer rate? 3.) It's been suggested that the use SMB vs. SMB2 could explain the differences in speed. Indeed, as expected, packet captures show both being used depending on the OS versions in play, as we would expect. I understand what determines SMB2 being used or not, but I'm curious to know what kind of performance gain you can expect with SMB2. My problem simply seems to be a lack of experience, and more importantly, perspective, in terms of what are and are not reasonable network speeds. Could anyone help impart come context/perspective?

  Read the article

• Do TCP connections work differently within the same subnet?

  - by Dean

  I've encountered some network behaviour that confuses me while trying to get Java RMI working. I use netcat to connect to a local machine: [my_machine]$ nc -w 1 192.168.0.100 60000 && echo success success I try to do the same to my server: [my_machine]$ nc -w 1 my-servers-ip 60000 && echo success This doesn't work, unless I explicitly listen on the server socket: [amazon_ec2]$ nc -l 60000 [my_machine]$ nc -w 1 my-servers-ip 60000 && echo success success For the version that fails, the SYN packet receives a RST, ACK in response. I'm not too knowledgable about this stuff, at this point I only have wild theories such as the one in the question. Any ideas? Potentially useful details: Local Machine (192.168.0.100) - Macbook Remote Machine (Amazon EC2) - Amazon Linux AMI 2012.03 Security Group Settings: 22 (SSH) 0.0.0.0/0 1099 0.0.0.0/0 49152-65535 0.0.0.0/0 "iptables -L" shows no rules set

  Read the article

• Sagem Router Wifi Key Issue

  - by user23392

  Hi I have a multiservices sagem router which supports wifi as well, the pack came up with a default wifi configuration key and a WEP Key in the label of the package like this: WIFI Configuration key: abcd1234 WEP Key: C4H2F167C10263AEB98V52920E Now, when i execute the wifi usb wizard in the official cd, it asks me for the WIFI key, i put the abcd1234 & it says it's incorrect, i try the long WEP key and it says that the key should only have 8 characters. When i go to the control panel of the router in the wifi config, i see that: Open Authentification System WEP 128 Bit Passphrase: C4H2F167C10263AEB98V52920E Now since the wizard only accepts 8 characters, i try to change the 128bit to 64bit and put some 8 characters and it ends up saying that the new key should be 5 or 13, or 10-26 hex numbers. What to do? Thanks

  Read the article

• Taskbar Disappears Over Remote Desktop Connection When Outside Local Network

  - by CMikeB1

  I've got a machine on my home network running Windows Server 2012 (Based on Win8) and rather than attach a monitor I remote desktop in and it works fine on my local network. The problem is, when I try to access it from outside my local network the taskbar disappears completely. When I minimize an application rather than minimize to the taskbar it simply closes the window as small as it can as if the taskbar never existed (see photos at ). I've messed with the connection properties (show/hide desktop background, etc.) with no luck. I've used the following methods to remote in and they all are fine when on the local network and taskbar-less from outside: Remote Desktop Connection on Mac Remote Desktop Connection on Windows Jump Desktop on iOS using RDP To access the computer from outside my local network I'm using a Linksys router and mapping to the server IP, port 3389. See Photos: http://i.stack.imgur.com/FyUeQ.png http://i.stack.imgur.com/9MnVr.png

  Read the article

• How can I restrict my mates to stop downloading?

  - by user239295

  We are sharing an internet broadband connection with 6 users at a place we live. We get 20 gb fup ( Fair usage policy) with 2 mbps speed from the ISP after the 20 gb is consumed the speed comes down to 512 kbps very difficult to browse any page. The problem is we cannot track which user/mate is downloading and ending the FUP. it is very difficult to track so is there something that we can allot per user some amount of space like 2 gb of downloading or restrict all from downloading so that we can utilize all the fup till the end of the month. We are using this connection as wifi configured. A adsl router is configured as wifi and we all using all 6 laptops. No PC. Any help would be appreciated. I apologize if i am not clear with my question.

  Read the article

• one of my web hostings is down - only for me - why ?

  - by Thomas Traub

  My first post here, I am reading / learning a lot, thanks ;). I've got a mysterious issue (for me) and would really appreciate to get it solved. I've rent a reseller package with bibihost.com and it's now the second time that all my domaines the hoster's site are unavailable from my connection (my Mac and my iPhone), (in browser, per FTP, ping, ab, and traceroute) This has never before happened to me with other web addresses. traceroute get's always stuck at a specific server 40g.vss-1-6k.routers.chtix.eu (91.121.131.29) The sites are all up for everyone else, I've checked with downforeveryoneorjustme.com, a homegrown script loaded to another server and montastic.com My question(s) : Why am I blocked ? Is there anything I can do about it ? If I cannot solve this issue I have to change the hoster, but I really would like to know what's going on. my domaines on this server : tienstiens.fr tomlegrand.com

  Read the article

• Temporarily configuring a default gateway (Windows Vista)

  - by justintime

  I would like to change the default gateway for the wired ethernet port on my laptop- the DHCP server is giving the wrong one. I would like it to revert to the existing config on a reboot. I would prefer a command line way of doing it - so I can easily repeat the command as needed. Do I need ipconfig or route - both of which confuse me.

  Read the article

• House Wiring for Ethernet/Coax/Power

  - by Adam Kragt

  Hoping this is the right place to post, the rest didn't seem to fit. If not, I apologize. Remodeling my house and want to wire up each room with Ethernet/coax wall ports. Both Ethernet, coax and power will be running through the sub-floor. I've read that there needs to be 2 ft between power cables and Ethernet to limit/prevent interference. Is this true? If not, does anyone know what the distance is? Thanks!

  Read the article

< Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >