Search Results

Search found 13457 results on 539 pages for 'superuser interface'.

Page 228/539 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

• How to use integrated support for dyndns clients in 2Wire router ?

  - by Frank

  I logged into the 2Wire web interface, and get to "Broadband Link Advanced Settings" page, how do I use it's integrated support for dyndns clients ? Under "Broadband DNS" it has "Obtain DNS information automatically" selected, under that : Manually configure your DNS information: Primary Server: Secondary Server: Domain Name: what do I need to do ?

  Read the article

• External USB attached drive works in Windows XP but not in Windows 7. How to fix?

  - by irrational John

  Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

  Read the article

• Login configuration script for Junos EX 2200 using minicom

  - by liv2hak

  I am connecting to Junos OS on Juniper EX-2200 switches using minicom as shown below minicom -C log_sw1 sw1 Now I have a series of commands that I need to execute on sw1.(example shown below) cli request system zeroize show config show interface edit delete protocols set system arp aging-timer 240 I want to avoid having to type these commands every time I log into the system.I want to put them in a config file and I want the it to be execute every time I log into the switch using minicom. Is there any way I can achieve this?

  Read the article

• itunes iphone sync stuck on "Waiting for items to copy"

  - by lindes

  superuser crowd, I've found a number of threads about this, but have yet to find a satisfactory answer. Perhaps I'll have better luck on this site?? I hope so... I'm having a problem with iTunes where syncing my iPhone ends up seeming to basically finish, but it says "Waiting for items to copy" after everything else, and just stays there for... well, a very long time, if I let it. Oh, and I'm not sure this is always the case, but at the moment, it's doing this while "Syncing Genius Data to [my iPhone] (Step 8 of 8)". If I click the little x in iTunes, it then gets stuck on "Canceling sync", for an equally indefinite sort of period. If I simply unplug the phone, everything seems to be synced and happy, but the next time I sync, it happens again. I presume this is a bug of some sort on Apple's part, but it seems like people have found workarounds... I'm just having trouble tracking one down that (a) is well described enough that I can actually follow it, (b) has enough detail that I can do it without losing data (i.e. tells me pathnames that I might want to copy first, or the like, before telling me to remove something) (note: see also point (a) -- I can't remove it if it's telling me to remove something that I don't know where it is!), and (c) otherwise seems sane. I'm hoping that here perhaps I'll get better luck -- with either a workaround, and/or debugging tips for figuring out how to find myself a workaround. Note: I'm busy with some other things at the moment, but can try to add some additional information later, if necessary.

  Read the article

• Determining the health of a Cisco switch port?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Dual NIC internet access

  - by JavaRocky

  Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on. Not sure how the routes table would look like. Q2. If one of the NICs link becomes unresponsive, would traffic be automatically routed to the other NIC? Thanks.

  Read the article

• Install iphone sdk DMG file on iMac but I can't find where any of the programs are located

  - by Tawani

  I just download the iPhone DMG file from apple and installed in on my new iMac (by following these directions: link text). The problem is, I can't seem to find where any of the programs got installed. I can't find XCode or Interface Builder in the applications list and everytime I click on the "iPhone SDK" icon in the applications list, it re-opens finder with the same packages that I am trying to install. P/S: I am completely new to the the Mac world so I might be doing everything completely wrong.

  Read the article

• subdomain on another ip address

  - by pixeline

  hello, my main domain (domain.com) sits on a server with ip address 1. I need to have a subdomain (forum.domain.com) point to a server with ip address 2. Both servers are hosted at iWeb, so i have a cPanel interface to manage them, but i can't find the right way to do that. I tried a .htaccess redirection, which works, but the visible address in the browser changes too. Any help on how to do that would be appreciated. Thank you

  Read the article

• MySQL is killing the server IO.

  - by OneOfOne

  I manage a fairly large/busy vBulletin forums (running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6x2GHz) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96 Other : From the cloud's IO chart, we're averaging 100mb/s read. > vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 9 0 73140 36336 8968 1859160 0 0 42 15 3 2 6 1 89 5 > /etc/init.d/mysql status Threads: 49 Questions: 252139 Slow queries: 164 Opens: 53573 Flush tables: 1 Open tables: 337 Queries per second avg: 61.302. moved from superuser

  Read the article

• Excel - working with multiple workbooks

  - by cKK

  Got about 50 workbooks that cannot be merged but need to make the data available in a nice easy way. Aany ideas how to open and close multiple workbook modally i.e control remains in some interface / menu window? all workbooks have multiple sheets and need to be opened read-only. thanks

  Read the article

• How to Make Flash Builder Package Explorer emulate Flex Builder’s Navigator window?

  - by eco_bach

  Hi Does anyone know if there is a way to make the new Package Explorer window in Flash Builder emulate Flex Builders 'Flex navigator' window? Bottom line is I don't always need to peer into SWC's, and I don't like having a 'default package' automatically created for me. Not sure why the interface wasn't made simpler, allowing access to more power and complexity only if necessary. I want to focus on the code, not on how to navigate and use the bells and whistles in the coding environment.

  Read the article

• Using tumblr auto-queue

  - by AK

  Can't get this thing to work. Has anyone else had any success with Tumblr's auto-publish queue feature? I have a bunch of items in my queue It's set to auto-publish once a day It's set to only publish between 1am and 3am The next morning nothing will be published. The interface isn't perfectly clear - is it attempting to auto-post at a time that's not between 1 - 3 and then giving up?

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• DHCP server with multiple interfaces on ubuntu, destroys default gateway

  - by Henrik Kjus Alstad

  I use Ubuntu, and I have many interfaces. eth0, which is my internet connection, and it gets its info from a DHCP-server totally outisde of my control. I then have eth1,eth2,eth3 and eth4 which I have created a DHCP-server for.(ISC DHCP-Server) It seems to work, and I even get an IP-address from the foreign DHCP-server on the internet facing interface. However, for some reason it seems my gateway for eth0 became screwed after I installed my local DHCP-server for eth1-eth4. (I think so because I got an IP for eth0, and I can ping other stuff on the local network, but I cannot get access to the internet). My eth0-specific info in /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.0.1.1 netmask 255.255.255.0 network 10.0.1.0 broadcast 10.0.1.255 gateway 10.0.1.1 mtu 8192 auto eth2 iface eth2 inet static address 10.0.2.1 netmask 255.255.255.0 network 10.0.2.0 broadcast 10.0.2.255 gateway 10.0.2.1 mtu 8192 My /etc/default/isc-dhcp-server: INTERFACES="eth1 eth2 eth3 eth4" So why does my local DHCP-server fuck up the gateway for eth0, when I tell it not to listen to eth0? Anyone see the problem or what I can do to fix it? The problem seems indeed to be the gateways. "netstat -nr" gives: 0.0.0.0 --- 10.X.X.X ---- 0.0.0.0 --- UG 0 0 0 eth3 It should have been 0.0.0.0 129.2XX.X.X 0.0.0.0 UG 0 0 0 eth0 So for some reason, my local DHCP-server overrides the gateway I get from the network DHCP. Edit: dhcp.conf looks like this(I included info only for eth1 subnet): ddns-update-style none; not authoritative; subnet 10.0.1.0 netmask 255.255.255.0 { interface eth1; option domain-name "example.org"; option domain-name-servers ns1.example.org, ns2.example.org; default-lease-time 600; max-lease-time 7200; range 10.0.1.10 10.0.1.100; host camera1_1 { hardware ethernet 00:30:53:11:24:6E; fixed-address 10.0.1.10; } host camera2_1 { hardware ethernet 00:30:53:10:16:70; fixed-address 10.0.1.11; } } Also, it seems that the gateway is correctly set if I run "/etc/init.d/networking restart" in a terminal, but that's not helpful for me, I need the correct gateway to be set during startup, and i'd rather find the source of the problem

  Read the article

• How to detect VPN disconnection with vpnc?

  - by Abhinav

  What is the easiest way to detect that a vpnc connection on Linux/Ubuntu has disconnected? Manually, I think the way to detect is to check whether the interface (tun0) appears in /sbin/ifconfig output. Is there a better way to find out immediately, so that a script can be run to restart the connection?

  Read the article

• custom MAIL server -> Proxy Server -> Gmail Server

  - by Eugene

  So I have some custom VPS which route emails via MX record in DNS. And I need to setup gmail interface via Google Apps - this step and previous are clear. But how can I insert some middle layer, to check emails messages for special words/etc., so something like spam assasin proxy, but custom product. The question is: How could i setup proxy mail from my server = to proxy server(or application) = to gmail servers? Thank you, for any help!

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• after installing monit when i do monit status myproc i get "error connecting to the monit daemon"

  - by Jason

  after installing monit when i do monit status myproc i get "error connecting to the monit daemon" I read somewhere that The status command won't work in the case that monit is running indaemon mode without its http support - the command 'monit status' in such case tries to get the status from the daemon via http/tcp. To start the http interface you need to add the 'set httpd ...' statement to theconfiguration. is that still correct? that post was from 2005

  Read the article

• Internet Sharing via router

  - by mak4pi

  Question: How to setup Internet Sharing among two computers (one Mac 10.5.6, one Ubuntu 9.10) via a router? Situation: The Mac is using AirPort (wireless interface) to connect to router as 192.168.1.101. The Ubuntu is using an ethernet cable to connect to router as 192.168.1.104. Visual: Mac )))))) Router ======= Ubuntu Any ideas are greatly appreciated. Thanks.

  Read the article

• Visual Studio 2005 won't install on Windows 7

  - by Peanut

  Hi, My question relates very closely to this question: http://superuser.com/questions/34190/visual-studio-2005-sp1-refuses-to-install-in-windows-7 However this question hasn't provided the answer I'm looking for. I'm trying to install Visual Studio 2005 onto a clean Windows 7 (64 bit) box. However I keep getting the following error when the 'Microsoft Visual Studio 2005' component finishes installing ... Error 1935.An error occurred during the installation of assembly 'policy.8.0.Microsoft.VC80.OpenMP,type="win32-policy",version="8.0.50727.42",publicKeyToken="1fc8b3b9a1e18e3b",processorArchitecture="x86",Please refer to Help and Support for more information. HRESULT: 0x80073712. On my first attempt to install VS 2005 I got a warning about compatibility issues. I stopped at this point, downloaded the necessary service packs and restarted the installation from the beginning. Every since then I just get the error message above. I keep rolling back the installation and trying again ... it's but always the same error. Any help would be very much appreciated. Thanks.

  Read the article

• remove addons from internet explorer 8 [closed]

  - by senthil

  Possible Duplicate: Why is it not possible to delete IE addons from the IE interface? In my "Manage Addons" dialog, there are lots of addons that I have no idea about. I never installed Java on my machine but a java addon is there. Then some other things. I am only able to disable them. How can I remove them and all the related files?

  Read the article

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Skype Connect as SIP/Trunk for Asterisk

  - by Kaurin

  First off: I'm not sure if this should be on superuser or here. I have recently built a few Asterisk boxes with OpenVOX FXO/FXS ports little or no trouble. My current project is building an Asterisk box with SIP trunks. My current employer insisted on getting Skype Business/Skype connect for that purpose. After reviewing the Skype Connect plan, I agreed, because I thought it is going to be straightforward: Purchase G729 licences and setup SIP trunk/trunks. Boy was i wrong :) Here is the setup: The setup is for calling US numbers only via skype (we got skype US minute bundles in skype connect) AsteriskNOW - Asterisk 1.4 + asterisk-gui Trunks: SIP Trunk configured with Skype Connect - shows as registered Users: 2 test extensions. Both work fine when calling each other, voicemail etc works fine too The asterisk box is behind a Mikrotik router which i configured to forward all relevant ports: 5060-5090 UDP, 10000-20000 UDP. When trying out an extension outside of my LAN, it worked. I could make calls to the other extension. Outgoing rule: _NXXXXXXXXX Strip:0 Prepend:+1 Use skype trunk Inbound rule: Trunk: Skype Pattern: s Destination: Extension1 (6210) Here is the output of asterisk CLI (-rvvvvv) with outgoing calls: http://pastebin.com/eWVpL72e you can see the circuit-busy response when using trunk1 (skype) When calling my Skype Connect number from the outside, I get nothing in the logs. Can anyone with Skype Connect / Asterisk experience help out? :)

  Read the article

• How to keep Ubuntu 11.10 and Kate editor w/terminal from changing command line when changing tabs?

  - by Kairan

  I am programming C using Kate editor in Ubuntu 11.10. It works great, but when I change tabs in Kate, the terminal line changes to the file path of the tab I click on. Normally this is not a big deal (other than annoyingly adding extra text to my terminal) however if I am currently RUNNNING a C program, it obviously will type at the command line, which is not so cool. Example terminal window for my C program (its at a menu): 1) select opt 1 2) select opt 2 Enter choice: (here it waits for prompt from user) Now when I click a tab in Kate, it wants to put in the cd / path of the file in that tab, such as: cd /home/user/os/files And of course since my terminal was waiting for prompt from user it gets that command.. not good. Perhaps there is no fix, but maybe someone knows? Obviously I could choose NOT to switch tabs or end program before switching tabs... Note: I probably made the mistake of putting this under StackOverflow which is more of a programming area - so though repost here might be best (I am not sure how to link the questions but will paste hyperlink to that post - I dont want to violate any stackoverflow/superuser violations) Suggestions on merging them are welcome or if I should delete one? StackOverFlow Question

  Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >