Search Results

Search found 13004 results on 521 pages for 'pretty printing'.

Page 229/521 | < Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• Just how slow should my VPN be?

  - by David Heggie

  I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

  Read the article

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• Using command line to connect to a wireless network with an http login

  - by Shane

  I'm trying to connect to a wifi network where it hijacks all requests and redirects you to a page where you have to agree to a terms of use before it lets you connect to the actual outside world. This is a pretty common practice, and usually doesn't pose much of a problem. However, I've got a computer running Ubuntu 9.10 server with no windowing system. How can I use the command line to agree to the terms of use? I don't have internet access on the computer to download packages via apt-get or anything like that. Sure, I can think of any number of workarounds, but I suspect there's an easy way to use wget or curl or something. Basically, I need a command line solution for sending an HTTP POST request essentially clicking on a button. For future reference, it'd be helpful to know how to send a POST request with, say, a username and password if I ever find myself in that situation in another hotel or airport.

  Read the article

• Cascading KVM switches

  - by einpoklum

  I have a not-so-small number of computers (say, 5) which I want to access with a single keyboard, USB and monitor. I can get an 8-port KVM switch, which is a pretty expensive piece of hardware; however, in theory, I should be able to cascade KVM switches: Have one 4-port KVM switch between 2 other KVMs (a 2-port and a 4-port). Is this doable (with typical off-the-shelf switches and cables)? Has anyone had experience doing this? Note: I'm interested in USB-only for the keyboard and mouse, and either VGA or DVI for the display. Audio and PS/2 connections are irrelevant for me..

  Read the article

• Windows 2008 Group Policy Setting? - Migration Headache

  - by DevNULL

  I have a small domain of users that I just migrated from a linux domain running open-ldap. Our new servers are running Windows 2008 Standard. I've installed Active Directory and everything is working perfectly... except that the initial user privileges is pretty restrictive and I need to loosen it up a bit. For example once they login to their workstations, they can create new files and folders but can not modify existing files or start. I basically want to open it all up except for software installations. Can someone please help with with this migration headache?

  Read the article

• How do you handle the task of changing the schema of a production MySQL database?

  - by Continuation

  One of the biggest complaints I have heard about MySQL is that it locks up a table if you try to change its schema like adding a column or adding an index. By "locking up the table" does it mean I can neither read nor write to the table? Sometimes for hours? That seems a pretty severe limitations. I was going to use MySQL for my new project but this gives me pause. Is there a workaround for this? How do you handle the task of changing the schema of your production MySQL database? By the way someone told me Postgresql doesn't have this problem. Is that true - I can both read and write to a Postgresql table while changing its schema? Is there any performance penalty incurred? Would love to hear your experiences.

  Read the article

• Colocation and HSRP setup

  - by WinkyWolly

  My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN. However I'm confused as to how to the IP setup should work. Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment. What's the proper way to do this?

  Read the article

• Upgrading Windows 7 on a new Netbook - Problems

  - by Swaffle

  I know this seems like a repeat of a question but i didn't get a clear answer from reading the other questions so im going to ask mine and hope i hear back good news. I bought an Acer Aspire one netbook with windows 7 starter. I have a DVD of Windows 7 Professional(x86) from MSNDAA through my college but when i tried to install it, i was given an error saying that i could only upgrade through the "Windows Anytime Upgrade" Though, it only gives me the options of paying for an upgrade, which im not willing to do, or putting in an upgrade key. I have a legitimate product key for windows 7 but it does not work for upgrading and the DVD does not allow for it. Am i doing something wrong? is there another option? can i convert my product key to an upgrade key ? Im up for any option, windows 7 starter is pretty limited in its features...

  Read the article

• Server responses "bus error" to every command

  - by Temnovit

  I have a linux machine dedicated to MySQL server with a pretty high load. Today I woke up and was terrified to see, that database server is down. I could connect to it via SSH, but it was responding with bus error to each and every command. [root@r1304 home]# ls Bus error [root@r1304 home]# tail /var/log/messages Bus error [root@r1304 home]# reboot Bus error [root@r1304 home]# free -m Bus error [root@r1304 home]# chkdisk Bus error I went to Data Center and did a hard reset, which seemed to help, but after a half an hour situation reapeated and now I can't even connet via SSH anymore. Any ideas what this could be? how to diagnose such a problem and what are possible fixes? Server has 32 GB RAM, 2xSSD drives with software RAID UPDATE According to Zabbix, when MySQL died, number of processes stated to increase drammaticaly, until I did a hard reset. What could those be? Number of processes

  Read the article

• Add SATA Port to Motherboard?

  - by YAS

  I recently took off the bottom covers to my laptop, an Aspire 6930, and one of the covers was hiding an empty space large enough for a second hard drive. The bit of motherboard that was showing had the solder joints for a SATA port, but no port. What I'm wondering is; If I get a spare SATA port and solder it in would it mess up my motherboard and kill my laptop? I'm not concerned about a clean solder job, I can do that. But if the port is soldered in cleanly if there would be any danger to doing it. It'd be pretty darn awesome to get a second hard drive in my laptop.

  Read the article

• why skype is not available on messengers like pidgin

  - by sterz

  i really like pidgin, empathy etc. (especially pidgin) because they gather all accounts like xmpp, msn etc. together except skype. i know skype uses a proprietary protocol but so does msn and it is available on pidgin. is it that hard to "put" skype on pidgin or alike messengers? what is the reason that skype is not implemented in pidgin? note: i know there is a plugin for pidgin to support skype but it requires the official skype client to be installed and running. pretty useless.

  Read the article

• irssi keybinding: backward_word/forward_word

  - by vikenemesh

  I'm currently experimenting with irssi as my irc client of choice and I'm getting along pretty well. BUT there is one thing I still need to get done. Somehow it isn't possible for me to use the usual CTRL+Left/Right to navigate between words in my input line. For the record: I'm using irssi on a linux-box through a screen session brought to my windows machine via ssh/putty. I already tried some key binding in irssi, maybe I did them wrong? /bind meta-n backward_word /bind meta-m forward_word both work fine. But neither /bind ^left backward_word /bind ^right backward_word nor /bind cleft-left backward_word /bind cleft-right backward_word work for a CTRL+Left/Right setup. Any Ideas?

  Read the article

• Why would anacron not be running?

  - by Rory

  I have a Ubuntu system that has anacron installed. However I'm pretty sure it's not running. It's not running the commands in /etc/cron.daily to rotate the syslog files (I'm using sysklog, which has its own rotating log method, not using logrotate). The last time the logs were rotated were in October 2009. /var/spool/anacron/cron.daily exists and the contents are 20091015. AFAIR we had a power outage then, and everything rebooted. How can I debug anacron? How can I see why it's not running? My first instinct is to look for /var/log/anacron, but that's not there. How can I fix it to make it run again?

  Read the article

• PackageForTheWeb "should not be executed directly"

  - by Sergei Ousynin

  When trying to install package (specifically, chipset drivers for Nexcom PEAK-series computer, but I guess it doesn't really matters) I get "PackageForTheWeb Error" saing "This program is used internally by PackageFromTheWeb. It should not be executed directly." I get this error on both Windows 2000 (where it should be installed) and Windows 7. The original driver CD was lost long time ago, so the package was downloaded from the Nexcom website, found no info about installer prerequisites there. What should I install (or anything else) to install this package? UPD: I found a solution - unpacked the package and executed setup.exe that was inside. But I'm pretty sure it's not an action supposed by vendor, so answers are still welcome.

  Read the article

• Lenovo ThinkServer TS130 1105 - does 32/64 depend on RAM?

  - by Ecnerwal

  Just got in a Lenovo ThinkServer TS130 1105 (Xeon E3-1225V1) and a (new, sealed, holographed, looks legit) copy of Windows Server 2008 32/64 (standard) to run on it for a pretty lightweight job (currently handled, adequately, by a terrifyingly old Optima P4 running Windows 2000 server - really lightweight, but long-past-due for replacement, without any particular need or excuse for server 2012...) The 64 bit disc sits there and does nothing. The 32 bit disc boots. I haven't spotted any mention of this in the TS130 Manual (I have now combed it, and find no mention of a need to populate in pairs - a preferred order to populate in, yes, but no mention of pairs being required) but I begin to wonder if it's due to the fact that the 4GB RAM suppled with it was a single DIMM, rather than a pair. Better for upgrading, but perhaps requiring an upgrade (or sidegrade) right away to install the x64 version?? Anyone know? I tried the 64-bit DVD on a desktop with an AMD Athlon II X4 635 processor which normally runs Windows7 in 64 bit, and it booted up just fine.

  Read the article

• Same folder history for "save folder" as "change folder"?

  - by Hendrik Vogt

  I use mutt as my e-mail client and have only one major annoyance. If I want to save an e-mail to a folder that I've used before as a "save folder", then I can use the up-arrow to navigate to the folder name. Now if I want to change into that folder, the up-arrow only gives me names of folders I've changed into before. It appears that mutt has two different folder histories for these two purposes. How can I configure mutt so that only one history is used for both purposes? (By the way, I'm pretty sure that older versions of mutt behaved exactly as I wanted, but unfortunately I can't tell the version number.)

  Read the article

• Mobile Intel 965 vs 4 Series chipset speed differences

  - by graham.reeds

  A client of ours is having a problem panning on a mapping application that we write on their panasonic toughbooks (CF-19's). One of their toughbooks the panning is fairly smooth while on the other it is really slow. Doesn't help that they have all the settings turned up, but I would of thought any reasonably new graphics card (even shared memory) would have more than adequate graphic speed. I am pretty sure that the graphic adapter is to blame, but I can't find anything out about either chipset (level of acceleration, non-problems, etc). All I get is the intel data sheets. The faster panning one is on the Mobile Intel 4 Series Express Chipset while the slower is on the Mobile Intel 965 Express Chipset. Is this expected? Does it sound like a driver problem? They both have the same amount of ram and same cpu.

  Read the article

• Installing GPSBabel on CentOS 5 x86_64

  - by Clint Chaney

  Well first let me say I have no clue about doing anything on my server, I ask my host to do all installs for me. I run a website where users store latitude and longitude coordinates in my database. I would like them to be able to download these waypoints to their gps units. I found a program called GPSBabel that allows this to be done. http://www.gpsbabel.org/ I want to be able to control GPSBabel from PHP using exec() or something along those lines. The problem is that the linux version of the program is a source file and they don't want to build or install it without some source of instructions. Does anyone have experience with installing this? Perhaps know someone that has and that can lead me in the right direction? Any help would be hugely appreciated. I'm pretty much stuck without getting this to work.

  Read the article

• How to change my commandline locale after CentOS decided to change it?

  - by Aron Rotteveel

  So apparently, CentOS decided I was Dutch, and thus, should not have a English locale. Apart from the fact that this greatly bothers me, I am having a pretty hard time actually changing it back. There does not seem to be a setlocale function, and system-config-language tells me I am using an English locale, even though my environment says otherwise. Any help would be appreciated. Output from locale: LANG=nl_NL.UTF-8 LC_CTYPE="nl_NL.UTF-8" LC_NUMERIC="nl_NL.UTF-8" LC_TIME="nl_NL.UTF-8" LC_COLLATE="nl_NL.UTF-8" LC_MONETARY="nl_NL.UTF-8" LC_MESSAGES="nl_NL.UTF-8" LC_PAPER="nl_NL.UTF-8" LC_NAME="nl_NL.UTF-8" LC_ADDRESS="nl_NL.UTF-8" LC_TELEPHONE="nl_NL.UTF-8" LC_MEASUREMENT="nl_NL.UTF-8" LC_IDENTIFICATION="nl_NL.UTF-8" LC_ALL= Both my ~/.bashrc as ~/.bash_profile contain no locale settings. Additionally, /etc/bashrc does not contain any locale references either.

  Read the article

• Home movie video browser

  - by Jim Hunziker

  I have a bunch of home movies that don't have useful filenames because they came straight off the camera. (I'm using Vista 64, by the way.) Picasa is pretty good for browsing through them and watching them, but it doesn't use my video card for rendering the videos. My CPU gets pegged at max usage, and full screen barely works. Windows Media Player or Quicktime works fine. Is there another application (like Picasa) that can be used for browsing through movies that both uses my video card and shows thumbnails of all the movies in my collection? I'd rather have something nicer than Windows Explorer. (The movies are h.264 AAC 1280x720.)

  Read the article

• Windows shortcut doesn't work: how to enclose filenames with spaces?

  - by Olivier Pons

  Here's my problem: I've made a shortcut on my Desktop (Windows XP (sigh)) like this: C:\WINDOWS\system32\cmd.exe /k "mysql -u root drupal-defaultadm < ^"C:\Documents and Settings\AAA\Mes documents\Downloads\01.drupal-defaultadm.sql^" && exit" When I double click on it, the DOS prompt is opened, but I get this error: File not found. C:\wamp\bin\mysql\mysql5.5.24\bin> So I'm trying to do the command "by hand" and only removing the ^: C:\wamp\bin\mysql\mysql5.5.24\bin>mysql -u root drupal-defaultadm < "C:\Documents and Settings\AAA\Mes documents\Downloads\01.drupal-defaultadm.sql" C:\wamp\bin\mysql\mysql5.5.24\bin> And gives no error. I'm pretty sure this has to do with the whitespaces enclosed with ". How shall I do to make it work?

  Read the article

• free -m output, should I be concerend about this servers low memory?

  - by Michael

  This is the output of free -m on a production database (MySQL with machine. 83MB looks pretty bad, but I assume the buffer/cache will be used instead of Swap? [admin@db1 www]$ free -m total used free shared buffers cached Mem: 16053 15970 83 0 122 5343 -/+ buffers/cache: 10504 5549 Swap: 2047 0 2047 top ouptut sorted by memory: top - 10:51:35 up 140 days, 7:58, 1 user, load average: 2.01, 1.47, 1.23 Tasks: 129 total, 1 running, 128 sleeping, 0 stopped, 0 zombie Cpu(s): 6.5%us, 1.2%sy, 0.0%ni, 60.2%id, 31.5%wa, 0.2%hi, 0.5%si, 0.0%st Mem: 16439060k total, 16353940k used, 85120k free, 122056k buffers Swap: 2096472k total, 104k used, 2096368k free, 5461160k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 20757 mysql 15 0 10.2g 9.7g 5440 S 29.0 61.6 28588:24 mysqld 16610 root 15 0 184m 18m 4340 S 0.0 0.1 0:32.89 sysshepd 9394 root 15 0 154m 8336 4244 S 0.0 0.1 0:12.20 snmpd 17481 ntp 15 0 23416 5044 3916 S 0.0 0.0 0:02.32 ntpd 2000 root 5 -10 12652 4464 3184 S 0.0 0.0 0:00.00 iscsid 8768 root 15 0 90164 3376 2644 S 0.0 0.0 0:00.01 sshd

  Read the article

• Outlook 2010 search stopped working with Exchange 2007

  - by Steve Hiner

  The quick search feature in Outlook 2010 used to work fine. We switched the computers over from a workgroup so that they are on the domain with our new server. We then copied all the email from the old PST file into the new Exchange based folders. Since we did that 3 of the 4 computers can't search email using Outlook's awesome search boxes. One of them works perfectly fine. Any idea what might have happened? There are only 5 users on the network and it's a pretty burly server for such a small network, I can't imagine the server is still indexing their mail. Is the quick search something that has to be turned on or might it be related to the permissions change from a non-domain user to a standard domain user?

  Read the article

• Using iptables to block ALL outgoing traffic from one NIC?

  - by edanfalls

  Hi, I must pretty bad at Googling as this seems like a very basic question but I can't seem to find the answer anywhere... and man iptables is a very long read! I have two NICs - eth0 and eth1 - on a linux box and I want to block ALL outbound traffic (TCP and UDP across all ports) from one of the NICs, so that no traffic makes its way back up to the router. What is the command for this? I have only seen examples with specific ports. Thanks in advance.

  Read the article

< Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >