Search Results

Search found 7768 results on 311 pages for 'enter'.

Page 232/311 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• Fedora installed in Legacy mode, how to make it work in UEFI?

  - by TryntaLearn

  I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

  Read the article

• Problems forwarding port 3306 on iptables with CentOS

  - by BoDiE2003

  Im trying to add a forward to the mysql server at 200.58.126.52 to allow the access from 200.58.125.39, and Im using the following rules (its my whole iptables of the VPS of my hosting). I can connect locally at the server that holds the mysql service as localhost, but not from outside. Can someone check if the following rules are fine? Thank you # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s 200.58.125.39 --dport 3306 -j ACCEPT -A INPUT -p tcp -s 200.58.125.39 --sport 1024:65535 -d localhost --dport 3306 -m state --state NEW,ESTABLISHED -j ACCEPT -A OUTPUT -p tcp -s localhost --sport 3306 -d 200.58.125.39 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT COMMIT And this is the output of the connection trial. [root@qwhosti /home/qwhosti/public_html/admin/config] # mysql -u user_db -p -h 200.58.126.52 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '200.58.126.52' (113)

  Read the article

• How to connect to DB2 when the password ends with '!' in Windows

  - by AngocA

  I am facing a problem to use the DB2 tools when using generic account with a generated password which ends with the Bang sign '!' to connect to DB2 database. I am not allowed to change the password because it is already used by other processes. I know the user is valid and I can connect to the database with its credentials, but not from all db2 tools. When using the Control Center it is okay. When using the Command Editor (GUI) or the Command Windows, I got this error message: connect to WAREHOUS user administrator using ! SQL0104N An unexpected token "!" was found following "<identifier>". Expected tokens may include: "NEW". SQLSTATE=42601 Let's say that my password is: pass@! I am trying to use c:\>db2 connect to sample user administrator using "pass@!" or c:\>db2 connect to sample user administrator using pass@! And it both cases I got the same error message. I could change the way I connect but it is not useful for me, for example: c:\>db2 connect to sample user administrator Enter current password for administrator: But I cannot use it from a batch file easily. I would like to know how can I connect from the Command Editor, in order to use this user from the Graphical Tools. BTW, I know that the Control Center is deprecated.

  Read the article

• ldap-authentication without sambaSamAccount on linux smb/cifs server (e.g. samba)

  - by umlaeute

  i'm currently running samba-3.5.6 on a debian/wheezy host to act as the fileserver for our department's w32-clients. authentication is done via OpenLDAP, where each user-dn has an objectclass:sambaSamAccount that holds the smb-credentials and an objectclass:shadowAccount/posixAccount for "ordinary" authentication (e.g. pam, apache,...) now we would like to dump our department's user-db, and instead use authenticate against the user-db of our upstream-organisation. these user-accounts are managed in a novell-edirectory, which i can already use to authenticate using pam (e.g. for ssh-logins; on another host). our upstream organisation provides smb/cifs based access (via some novell service) to some directories, which i can access from my linux client via smbclient. what i currently don't manage to do is to use the upstream-ldap (the eDirectory) to authenticate our institution's samba: i configured my samba-server to auth against the upstream ldap server: passdb backend = ldapsam:ldaps://ldap.example.com but when i try to authenticate a user, i get: $ smbclient -U USER \\\\SMBSERVER\\test Enter USER's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.6.6] tree connect failed: NT_STATUS_ACCESS_DENIED the logfiles show: [2012/10/02 09:53:47.692987, 0] passdb/secrets.c:350(fetch_ldap_pw) fetch_ldap_pw: neither ldap secret retrieved! [2012/10/02 09:53:47.693131, 0] lib/smbldap.c:1180(smbldap_connect_system) ldap_connect_system: Failed to retrieve password from secrets.tdb i see two problems i'm having: i don't have any administrator password for the upstream ldap (and most likely, they won't give me one). i only want to authenticate my users, write-access is not needed at all. can i go away with that? the upstream ldap does not have any samba-related attributes in the db. i was under the impression, that for samba to authenticate, those attributes are required, as smb/cifs uses some trivial hashing which is not compatible with the usual posixAccount hashes. is there a way for my department's samba server to authenticate against such an ldap server?

  Read the article

• Port Forwarding to put my web server on The Internet

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• Application Pool Identity corruption

  - by Gavin Osborn

  I have observed a few times while deploying software into IIS that every now and again the related Application Pools fail to restart and in the Event Log we see an error like the following: The identity of application pool, 'AppPoolName' is invalid. If it remains invalid when the first request for the application pool is processed, the application pool will be disabled. This does not happen frequently but when it does the only solution is to re-apply the Identity password in the IIS Manager Window. As soon as I re-apply and then restart the application pool the web sites come back up. Facts: The account is a service account whose password never expires. The account is local to the IIS host. The account password is never changed. This is IIS 6 running on Windows Server 2003 Deployment of the software is via MSI and involves several IIS Resets. The software is created in house and does not do anything fancy to IIS. Any ideas how the identity information might become corrupt? Edit: Clarification To be clear - this user account and password combination work absolutely fine and usually works fine as the Identity of the Application Pool. It is only when we deploy updates of our software into an existing IIS application that it stops working. Our password has not changed Our deployment does not change the password or reconfigure the application pools. This does not happen every time, 1/20 times perhaps. If we re-enter the password into IIS and restart the App Pools everything works.

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

• How to connect AD Explorer from Sysinternals to Global Catalog

  - by Oliver

  I'm using the sysinternals AD Explorer quite frequently to search and inspect an Active Directory without any big problems. But now i'd like to connect not only to a single AD Server. Instead i like to inspect the global catalog. If i enter within the AD Explorer connect dialog only the dns name of the machine (e.g. dns.to.domain.controller) that is serving the global catalog i only receive the concrete domain for which it is responsible, but not the whole forest (that's normal behaviour and expected by me). If i'm going to add the default port number (3268) for the global catalog in the form dns.to.domain.controller:3268 AD Explorer will simply crash without any further message. The global catalog itself works as expected under the given name and port number, cause our apache server use exactly this address and port number to authenticate some users. So any hints or tips to access the global catalog out of AD Explorer? Or there are any other nice tools like AD Explorer out there that doesn't have any problems to access the global catalog?

  Read the article

• Problem with running a script at startup as root?

  - by Usman Ajmal

  Hi The main question: Is there a way I can run 'completely' one of my script when ubuntu's desktop appears no matter if root , administrator, desktop user or an unprivileged user logged in? What does the script do? The script mounts a partition, looks for a file in that partition and finally on the basis of that file a decision of copying a partition to another partition is made. That copying is done via dd if=/dev/sda2 of=/dev/sda5 When does the script run finely? Script runs smoothly when I run it from the terminal by sudo ./my_copying_script This command asks me for the password of currently logged in user. I enter the password and the script starts working. When does the script NOT run finely? I want to run the script at startup. I set it a startup program by using the Startup Applications utility of Ubuntu. Script ran at startup but exited at the dd command returing following error: dd: opening '/dev/sda2': Permission denied On edk's suggestion I set the owner of my_copying_script as root and set the SUID. Now the permissions of my_copying_script are (-rwsr-sr-x). edk's point of view was that once I set the suid, the startup program will run with the permissions of its owner. I did that but the same /dev/sda2 permission denied error came up. I then prefixed the dd with sudo as mentioned below sudo dd if=/dev/sda2 of=/dev/sda5 but this returned following error: sudo: no tty present and no askpass program specified In other words the mounting failed. If I run the script using sudo ./myProgram i don't face this problem and the drive gets mounted successfully.

  Read the article

• how do you view / access the contents of a mounted dmg drive through TERMINAL hdiutil diskmount

  - by A. O.

  My external USB drive failed. I made a .dmg image file of the drive using disk utility. Later I was not able to mount the .dmg image. I used terminal hdiutil attach -noverify -nomount name.dmg diskutil list diskutil mountDisk /dev/disk4 then received the following message: Volume(s) mounted successfully However, I cant see the drive or access its contents through Finder. DUtility shows the drive as ghost but I still cant mount it using diskutility. Terminal tells me that the drive is mounted and constantly shows it in the diskutil list. pwd is not the mounted .dmg image. I dont know how to enter into the mounted image drive to see its contents. So in case what I said sounds like I see the files in the mounted image no this is not the case. I do not know how to access or even change the pwd within Terminal. I was hoping to see the mounted drive tru finder but I do not see that. So I need help as to how to find a way to access the mounted image drive if it was really mounted. Terminal says that it was and it shows it under diskutil list as a /dev/disk4. Can someone please help me access the files on this drive?

  Read the article

• Connections to SSH and Samba suffer from heavy delay

  - by Till Helge Helwig

  There are a lot of questions about SSH connections being delayed, which usually can be fixed by disabling the DNS lookups. Unfortunately this doesn't seem to be my problem. Our development server is accessed via SSH and Samba. When opening a connection to the server (either SSH or Samba) it takes a very long time. Accessing a Samba share via Windows is basically impossible because there is a timeout. Using smbclient works, but takes ages. When opening a SSH connection I get immediately prompted for the password and after hitting Enter the terminal instantly shows the MOTD. Afterwards it takes about a minute for the prompt to appear. I watched the load of the server while connecting via SSH and Samba and could not find anything out of order. There is nothing out of the ordinary running and hogging up memory and CPU or something. I have no clue where this delay might come from. I already tried UseDNS no in sshd_config and proxy_dns = no in smb.conf, but to no avail. Any idea about what might cause this would be greatly appreciated!

  Read the article

• Use autocomplete in dropdown cells with Excel 2007?

  - by Martin

  I want to make a survey with Excel and I therefore have defined the cells for the answers as a dropdown cell which only accepts answers from a certain list, e. g.: The two Lists List1 and List2 (yellow cells) are the possible answers for the questions in Block 1.x resp. 2.x (blue) . There might be a block 4 with more questions, which again use List1 for their possible answers. My problem is: I'd like to be able to use the autocompleate feature to fill in the blue cells with the dropdown menu, so that the user only types 5 and it automatically expands to "5: extremely important" or "5: extremely difficult". According to my research on the www, this should be possible if I add the list with possible answers directly above the cells where autocomplete should work (I did this with the green helper cells which could be hidden) . But I have to enter at least 4 characters 5: e to get the autocompleted suggestion. Is there a way to make autocomplete already replace a "5" by the corresponding valid term? As the survey file shall be distributed to a lot of people "outside", I can not use VBA magic because it may be blocked on their computer and might not work. EDIT: it seems to have to do with the numbers I use: If I'd start my List items with A, B, C instead of 1, 2, 3, it would work perfectly. Excel seems to ignore the pure numbers when they are entered and does not try to autocomplete them.. is there a workaround? (I hope it is clear what I want, it seems a little difficult to explain.)

  Read the article

• Windows Not Honoring DHCP Scope

  - by jerhinesmith

  Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• In which order does Excel process its formulae?

  - by dwwilson66

  I've got a fairly large spreadsheet with major calculations going on, and it's starting to slow down every time a value that's part of a calculated field is modified. I'm in the process of optimizing the file, adding arrays where I can, and seeing where I can shave off a few milliseconds here and there. Let's say there's data in Columns A-H. Column H is set based on relationships between values in Columns A, B and C, which change dynamically from an outside program. Users enter the data in Column F. Formulas in D & E calculate relationships between F & H and H & D, respectively. How does Excel manage formulae in the case, for instance, where they're dependent on data further into the sheet? Will my value in H be available the first time that the formulae in D & E calculate? or, will D & E calculate based on an old value for H, because H's update hasn't happened yet? Are there any efficiencies to be gained by positioning dependencies in particular rows or columns in the speadsheet? Do positions above and left the current position get processed sooner than things below and to the right?

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• Smart card driven membership and door entry system

  - by Rob G

  I'm looking at putting in a smart card driven system at my local sports club (which doesn't have oodles of money), and since they're willing to pay for hardware, and I'm willing to do the technical setup, I was wondering if anyone had any experience in setting something like this up. Writing any software needed is not the problem, I've pretty much got that covered with various open source projects out there and custom code I'll write, but it's more the hardware side I'm not too sure about and I'm looking for advice from people out there. I'm sure there are numerous complications, but on the surface it looks fairly simple. I'd basically like to enable members to swipe/touch a smart card at the door to gain entry to the club, walk up to a touch screen PC and swipe/touch a card reader there to "login" to the system I create, which will allow them to book club facilities etc. I may even want that same card to then activate things like lights or music when they enter the room they've booked. Pretty Eutopian I know, but still, we'd like to get as close as we can. As I said, the software shouldn't be a problem, and on the hardware side, so far I'm looking at: All in one touch screen PC running Windows 7 or Ubuntu USB card reader (not sure which one to buy) Smart Cards (again, never bought these before) Door/lighting hardware that could be triggered (not sure here either) If anyone has any advice on implementing something like this - especially the items I'm not sure about above, and of course anything I've missed out that's crucial, I'd be most grateful. Recommended hardware that you've used for something like this would be fantastic!

  Read the article

• Difficult to point-and-click target with Apple Magic Trackpad?

  - by Andrew Swift

  My Magic Trackpad is great for most things involving dragging and gestures, but for simple point-and-click use it is starting to get really annoying. For example, my bank has a numeric code that I need to enter from a visual grid on the screen, by clicking on the six numbers in order. To do this is quite difficult with the Magic Trackpad. Idea 1: it is because when you start dragging on the touchpad, there is a brief delay before the mouse starts to move. The delay might be enough to screw up my anticipation of where the cursor is going to go. Idea 2: it may have to do with the cursor acceleration. If I move it a little, the cursor moves a little. If I move it a lot, it goes much faster. I have tried various settings in the preference pane, and although the cursor does move more or less quickly, it doesn't seem any more or less easy to hit a given target. As I am writing this post, I tried a brief experiment -- I chose a spot on the page (the bracket in the superuser logo) and tried to move the cursor there in one quick movement. It's extremely difficult, even though I've been using Macs and touchpads since 1999. There is something about the behavior of the trackpad that is making it impossible for me to learn how to accurately predict where the cursor will end up. Does anyone else have this problem?

  Read the article

• How to use the outcome of a formula as the value for Vlookup or another IF formula

  - by Steven

  Ok I will try to explain my issue effectively. I am making a GPA sheet in which the value out of 100 is computer in to a GPA value and then in to a letter. In cell N5 i have the value of all their grades (formula: =H3+H4+H5) Now in cell (j6) I have a formula which is giving them a number depending on the value calculated in N5 (Formula: =IF(AND(N5>=60,N5<=63.999),"2.0",IF(AND(N5>=64,N5<=66.999),"2.25",IF(AND(N5>=67,N5<=69.999),"2.4",IF(AND(N5>=70,N5<=73.999),"2.5",IF(AND(N5>=74,N5<=76.999),"2.75",IF(AND(N5>=77,N5<=79.999),"2.9",IF(AND(N5>=80,N5<=83.999),"3.0",IF(AND(N5>=84,N5<=86.999),"3.25",IF(AND(N5>=87,N5<=89.999),"3.4",IF(AND(N5>=90,N5<=93.999),"3.50",IF(AND(N5>=94,N5<=96.999),"3.75",IF(AND(N5>=97,N5<=100),"4",IF(AND(N5<=59.999),"0"))))))))))))) Still no problem... as the values I was looking for comes out (example 84.2 shows up as 3.25 as I wanted). However here comes the problem.... I have tried to use the outcome in J6 to do Vlookup or another if formula, however excel does not seem to recognize the value in J6. For example: =VLOOKUP(j6,B3:C15,2,FALSE)... this returns N/A however if I enter =VLOOKUP(3.25,B3:C15,2,FALSE) it gives me what im looking for. It seems that excel will not register the outcome of my formula as a number. What can I do please?

  Read the article

• Office 2010 OCT Outlook Filepaths

  - by vlannoob

  I'm playing around with customizing Office 2010 installs on my network, normally I just do a full manual install, but as the environment grows and the lazier I get its becoming a pain to do it manually every time. I've read up and downloaded the Office 2010 OCT tool and it looks relatively straight forward - with one exception - the Outlook Profile. I can 'get around it' by just leaving it all as default (or not enabling offline use) but I'd like to customise it slightly so that its all setup no matter who logs onto the PC. The only issue I have, and my question is: In the OCT - Outlook section What do you enter into the Path and Filename for the OST file and the Offline Address book seetings under Enable Offline Use section? I'm sweet with everything else - just that one section, and I think if I bugger that one it will kill the whole Outlook Profile?? It would need to go into each users unique filepath for their profile correct? I have a fair idea of what should be there but I'm struggling with the correct syntax. I know this is a stupid question....but its late in the day and my brain is fried ;) As usual - any and all help/assistance is appreciated ;)

  Read the article

• What can be a reason for phpMyAdmin login to be not working (not at all, no reaction on submit)?

  - by Ivan

  When I open "http://localhost/phpmyadmin/", enter "root" as the user name and my MySQL root password and press go, then if I was using Firefox, I was getting offered to download index.php file (of a zero length), if I was using Opera 11, it said "Connection closed by remote server". Following recommendations I've removed all packages related to phpMyAdmin, PHP, MySQL and Apache and then reinstalled them step-by step (instead of just issuing apt-get install phpmyadmin and relying on the system to install the whole LAMP stack via dependencies as I've done before). The only change I've got was Firefox to stop offering to download index.php - now when I press Ok to submit my password, it just doesn't show any visible reaction at all. What may the reason be and how to fix it? I use up-to-date Xubuntu 11.04. Reinstalling the whole LAMP stack and phpMyAdmin did not help, neither did removing AppArmor. I've tried to use SQLBuddy instead, but there's exactly the same problem. So, I think, the problem is not in phpMyAdmin but in MySQL, Apache or something. MySQL seems to work if I use command line to access it. Apache & PHP seems to work also, as the login page of phpMyAdmin displays correctly.

  Read the article

• Backup Picasa 'people' tags data

  - by pelms

  OK, so I've spent a fair amount of time putting names to faces in Picasa 3.5 but in a few days (hopefully) my copy of Windows 7 should arrive and I'll need to reinstall Windows. So, does anyone know what I need to backup so that I don't have to re-enter all those name tags? N.B. I'm on Windows 7 RC and know that I don't have to do a clean reinstall but I would prefer to. Outcome: I clean installed Windows 7 and downloaded and installed Picasa. Unfortunately, the download link on the UK Picasa homepage still pointed to Picasa 3.0 (rather than 3.5) which doesn't have face recognition. This scanned my photos folders and overwrote the picasa.ini files along with the people information   :¬( Fortunately I'd backed up the photos before installing Win 7, so after uninstalling Picasa 3.0 (along with it's database), restoring the photos from backup and installing Picasa 3.5, I finally got my face names back. Extra... Google has now posted advice on how to migrate to Windows 7 and keep your Picasa database, meaning that it will not need to rescan you photos and will retain all information about then including name tags. They have a method for upgrading and for a clean install of Win 7. Basically you need to back up: "C:\Users\%username%\AppData\Local\Google\Picasa2" and "C:\Users\%username%\AppData\Local\Google\Picasa2Albums"

  Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >