Search Results

Search found 13225 results on 529 pages for 'dynamic variables'.

Page 233/529 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

• D-LINK 2450U DSL router: Port forwarding forwading to the modem itself, not the specified IP

  - by axk

  I found a similar question but it has no satisfactory answers. I have a D-LINK 2540U DSL router. It has a basic port forwarding(under DNS - Virtual Servers) configuration in the administration panel where you specify: external port range, protocol, internal port range, server IP address and it is supposed to forward that port to that IP address. When I first set it up for a Real VNC connection it worked fine, just as I expected. Then I added a DynDNS configuration entry in the router's 'Dynamic DNS' section and added an additional SSH (22) forwarding rule. The SSH forwarding also worked fine (now with the dynamic hostname, but I suppose it doesn't make any difference as far as SSH is concerned). Then I removed the SSH rule and after that the VNC forwarding stopped working with the VNC client failing to connect (I have tried to connect with telnet and it also failed to connect, so it wasn't a VNC problem). After adding a rule for port 80 it turned out it would forward on port 80 though not to the specified server IP but to the modem itself. At least it is what it looks like, because it gives me the administration panel when I connect to my external IP (both using a browser and plain telnet in which case I can see that it is mini_hhtpd sitting on the port, which is obviously the modem's administration panel). Have anybody encountered a similar problem with port forwarding? I have tried to do a reset through the administration panel and to restore a backup of the settings made before I started playing with port forwarding, but it didn't help. Should I do a 'hard' reset with the button on the modem? Is it any different from the administration panel's reset (Restore default)?

  Read the article

• Whitelist IP from google-authenticator in sshd pam

  - by spudwaffle

  My Ubuntu 12.04 server uses the google-authenticator pam module to provide two step authentication for ssh. I need to make it so that a certain IP does not need to type the verification code. The /etc/pam.d/sshd file is below: # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password auth required pam_google_authenticator.so I've already tried adding a auth sufficient pam_exec.so /etc/pam.d/ip.sh line above the google-authenticator line, but I can't understand how to check an IP adress in the bash script.

  Read the article

• Please, help writing a MIB

  - by facha

  I have a problem with an snmpwalk query returning snmp variables in a non-uniform way: .1.3.6.1.2.1.10.127.1.3.3.1.2.215 -> Hex-STRING: 24 37 4C 0C 65 0E .1.3.6.1.2.1.10.127.1.3.3.1.2.216 -> Hex-STRING: 24 37 4C 0B A2 DA .1.3.6.1.2.1.10.127.1.3.3.1.2.217 -> STRING: "$7L f:" .1.3.6.1.2.1.10.127.1.3.3.1.2.218 -> STRING: "$7L k2" As you can see, some variables are of a STRING type, others are Hex-STRING. So, I'm trying to write a simple MIB to force them all come out as Hex-STRING. This is where I've gotten so far: TEST-MIB DEFINITIONS ::= BEGIN PhysAddress ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:" STATUS current SYNTAX OCTET STRING test OBJECT-TYPE SYNTAX PhysAddresss MAX-ACCESS read-only STATUS current ::= { 1 3 6 1 2 1 10 127 1 3 3 1 2 } END However, snmpwalk doesn't seem to notice my textual convention (even though the "test" variable is being recognized). I still get a mixture of STIRNGs and Hex-STRINGs. Could anybody point to where is my mistake? snmpwalk -v2c -cpublic 192.168.1.2 TEST-MIB::test ... TEST-MIB::test.216 = Hex-STRING: 24 37 4C 0B A2 DA TEST-MIB::test.217 = STRING: "$7L f:"

  Read the article

• Setting "Register this connection's addresses in DNS" using GPO

  - by ChamaraG

  Hi All, I need to get the Windows XP client machines in my network to dynamically update their DNS A records. The network is an AD domain running on Windows Server 2003 R2 servers with Win XP SP3 clients. Some machines already have the "Register this connection's addresses in DNS" check box checked and sucessfully update the DNS server. But some machines do not have this check box set and I need to set this. I read that this is possible using a GPO and I enabled the following: Computer configuration - Administrative templates - Network - DNS client Primary DNS Suffix Dynamic Update DNS Servers Connection-Specific DNS Suffix Register DNS records with connection-specific DNS suffix and where required, entered the relevant parameters. Running rsop.msc in the client machines shows that the GPO has been applied. The client machines have been rebooted. The DNS server allows "Nonsecure and secure" dynamic updates and is only accessible from our internal network. But, the "Register this connection's addresses in DNS" check box is not set. And the hosts without this set are not updating their DNS A records. Per another suggestion in a web site, i tried running "ipconfig /registerdns", but it does not add the DNS A record. Any advice on what I am doing wrong here would be gratefully accepted :-) Thank you.

  Read the article

• Apache + Codeigniter + New Server + Unexpected Errors

  - by ngl5000

  Alright here is the situation: I use to have my codeigniter site at bluehost were I did not have root access, I have since moved that site to rackspace. I have not changed any of the PHP code yet there has been some unexpected behavior. Unexpected Behavior: http://mysite.com/robots.txt Both old and new resolve to the robots file http://mysite.com/robots.txt/ The old bluehost setup resolves to my codeigniter 404 error page. The rackspace config resolves to: Not Found The requested URL /robots.txt/ was not found on this server. **This instance leads me to believe that there could be a problem with my mod rewrites or lack there of. The first one produces the error correctly through php while it seems the second senario lets the server handle this error. The next instance of this problem is even more troubling: 'http://mysite.com/search/term/9 x 1-1%2F2 white/' New site results in: Bad Request Your browser sent a request that this server could not understand. Old site results in: The actual page being loaded and the search term being unencoded. I have to assume that this has something to do with the fact that when I went to the new server I went from root level htaccess file to httpd.conf file and virtual server default and default-ssl. Here they are: Default file: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / # force no www. (also does the IP thing) RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} !^mysite\.com [NC] RewriteRule ^(.*)$ http://mysite.com/$1 [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Default-ssl File <IfModule mod_ssl.c> <VirtualHost _default_:443> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / RewriteCond %{SERVER_PORT} !^443 RewriteRule ^ https://mysite.com%{REQUEST_URI} [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on # Use our self-signed certificate by default SSLCertificateFile /etc/apache2/ssl/certs/www.mysite.com.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.mysite.com.key # A self-signed (snakeoil) certificate can be created by installing # the ssl-cert package. See # /usr/share/doc/apache2.2-common/README.Debian.gz for more info. # If both key and certificate are stored in the same file, only the # SSLCertificateFile directive is needed. # SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem # SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/apache2/ssl.crt/server-ca.crt # Certificate Authority (CA): # Set the CA certificate verification path where to find CA # certificates for client authentication or alternatively one # huge file containing all of them (file must be PEM encoded) # Note: Inside SSLCACertificatePath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCACertificatePath /etc/ssl/certs/ #SSLCACertificateFile /etc/apache2/ssl.crt/ca-bundle.crt # Certificate Revocation Lists (CRL): # Set the CA revocation path where to find CA CRLs for client # authentication or alternatively one huge file containing all # of them (file must be PEM encoded) # Note: Inside SSLCARevocationPath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCARevocationPath /etc/apache2/ssl.crl/ #SSLCARevocationFile /etc/apache2/ssl.crl/ca-bundle.crl # Client Authentication (Type): # Client certificate verification type and depth. Types are # none, optional, require and optional_no_ca. Depth is a # number which specifies how deeply to verify the certificate # issuer chain before deciding the certificate is not valid. #SSLVerifyClient require #SSLVerifyDepth 10 # Access Control: # With SSLRequire you can do per-directory access control based # on arbitrary complex boolean expressions containing server # variable checks and other lookup directives. The syntax is a # mixture between C and Perl. See the mod_ssl documentation # for more details. #<Location /> #SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \ # and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \ # and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \ # and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \ # and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \ # or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/ #</Location> # SSL Engine Options: # Set various options for the SSL engine. # o FakeBasicAuth: # Translate the client X.509 into a Basic Authorisation. This means that # the standard Auth/DBMAuth methods can be used for access control. The # user name is the `one line' version of the client's X.509 certificate. # Note that no password is obtained from the user. Every entry in the user # file needs this password: `xxj31ZMTZzkVA'. # o ExportCertData: # This exports two additional environment variables: SSL_CLIENT_CERT and # SSL_SERVER_CERT. These contain the PEM-encoded certificates of the # server (always existing) and the client (only existing when client # authentication is used). This can be used to import the certificates # into CGI scripts. # o StdEnvVars: # This exports the standard SSL/TLS related `SSL_*' environment variables. # Per default this exportation is switched off for performance reasons, # because the extraction step is an expensive operation and is usually # useless for serving static content. So one usually enables the # exportation for CGI and SSI requests only. # o StrictRequire: # This denies access when "SSLRequireSSL" or "SSLRequire" applied even # under a "Satisfy any" situation, i.e. when it applies access is denied # and no other module can change it. # o OptRenegotiate: # This enables optimized SSL connection renegotiation handling when SSL # directives are used in per-directory context. #SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> # SSL Protocol Adjustments: # The safe and default but still SSL/TLS standard compliant shutdown # approach is that mod_ssl sends the close notify alert but doesn't wait for # the close notify alert from client. When you need a different shutdown # approach you can use one of the following variables: # o ssl-unclean-shutdown: # This forces an unclean shutdown when the connection is closed, i.e. no # SSL close notify alert is send or allowed to received. This violates # the SSL/TLS standard but is needed for some brain-dead browsers. Use # this when you receive I/O errors because of the standard approach where # mod_ssl sends the close notify alert. # o ssl-accurate-shutdown: # This forces an accurate shutdown when the connection is closed, i.e. a # SSL close notify alert is send and mod_ssl waits for the close notify # alert of the client. This is 100% SSL/TLS standard compliant, but in # practice often causes hanging connections with brain-dead browsers. Use # this only for browsers where you know that their SSL implementation # works correctly. # Notice: Most problems of broken clients are also related to the HTTP # keep-alive facility, so you usually additionally want to disable # keep-alive for those clients, too. Use variable "nokeepalive" for this. # Similarly, one has to force some clients to use HTTP/1.0 to workaround # their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and # "force-response-1.0" for this. BrowserMatch "MSIE [2-6]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 # MSIE 7 and newer should be able to use keepalive BrowserMatch "MSIE [17-9]" ssl-unclean-shutdown httpd.conf File Just a lot of stuff from html5 boiler plate, I will post it if need be Old htaccess file <IfModule mod_rewrite.c> # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)/$ /$1 [r=301,L] # codeigniter direct RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)$ /index.php/$1 [L] </IfModule> Any Help would be hugely appreciated!!

  Read the article

• Cannot access host from a virtualbox guest using bridged adapter

  - by David Dai

  I have a windows 7 host with firewall turned off. And I have a windowsXP guest running on Virtualbox 4.2.4r81684. In my windowsXP guest I tried to connect to the FTP server on my host machine(which used to work well) but it didn't work. I tried to ping my host machine, but it didn't work either. Then I tried to ping my guest from host, it worked well. my guest ip is :192.168.1.95 my host ip is : 192.168.1.9 route table on guest machine is this: C:\Documents and Settings\wenlong>route PRINT =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...08 00 27 66 54 6c ...... AMD PCNET Family PCI Ethernet Adapter #2 - Packe t Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.95 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.95 192.168.1.95 20 192.168.1.95 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.1.255 255.255.255.255 192.168.1.95 192.168.1.95 20 224.0.0.0 240.0.0.0 192.168.1.95 192.168.1.95 20 255.255.255.255 255.255.255.255 192.168.1.95 192.168.1.95 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None arp cache is this: C:\Documents and Settings\wenlong>arp -a Interface: 192.168.1.95 --- 0x2 Internet Address Physical Address Type 192.168.1.1 00-26-f2-60-3c-04 dynamic 192.168.1.9 90-e6-ba-c2-90-2f dynamic It's strange because there was no problem days before and I didn't make any changes to the setting. could anybody help? PS. the guest can communicate with other machines in the LAN(for example 192.168.1.114) ok. it just cannot connect to the host machine.

  Read the article

• Mac OS X Client With Static DHCP Assignment Requests Wrong IP via Option 50

  - by Starchy

  I have a number of Mac (and a few Linux) laptops getting DHCP from a Force10 layer 3 switch, the only DHCP server on the subnet. There's a global dynamic pool, and for each full-time employee's laptop I have a single IP static pool set by MAC address. One and only one of the clients, running OS X 10.7.5, consistently fails to get a static assignment. The MAC address in the static pool definition has been carefully re-checked. Running tcpdump on a mirrored port when the laptop connects, I see that it is specifically requesting 10.100.0.252 (a dynamic address): 11:32:10.108280 IP (tos 0x0, ttl 255, id 28293, offset 0, flags [none], proto UDP (17), length 328) 0.0.0.0.bootpc > broadcasthost.bootps: [udp sum ok] BOOTP/DHCP, Request from 3c:07:54:xx:xx:xx (oui Unknown), length 300, xid 0x1399da89, Flags [none] (0x0000) Client-Ethernet-Address 3c:07:54:xx:xx:xx (oui Unknown) Vendor-rfc1048 Extensions Magic Cookie 0x63825363 DHCP-Message Option 53, length 1: Request Parameter-Request Option 55, length 9: Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name Option 119, LDAP, Option 252, Netbios-Name-Server Netbios-Node MSZ Option 57, length 2: 1500 Client-ID Option 61, length 7: ether 3c:07:54:xx:xx:xx Requested-IP Option 50, length 4: 10.100.0.252 Lease-Time Option 51, length 4: 7776000 Hostname Option 12, length 10: "host-name" END Option 255, length 0 PAD Option 0, length 0, occurs 8 I haven't been able to find any extra system prefs or unusual software on the laptop. Disabling the interface and rebooting or temporarily setting the IP manually both fail to make any difference. Any suggestions appreciated.

  Read the article

• uWSGI cannot find "application" using Flask and Virtualenv

  - by skyler

  Using uWSGI to serve a simple wsgi app, (a simple "Hello, World") my configuration works, but when I try to run a Flask app, I get this in uWSGI's error logs: current working directory: /opt/python-env/coefficient/lib/python2.6/site-packages writing pidfile to /var/run/uwsgi.pid detected binary path: /opt/uwsgi/uwsgi setuid() to 497 your memory page size is 4096 bytes detected max file descriptor number: 1024 lock engine: pthread robust mutexes uwsgi socket 0 bound to TCP address 127.0.0.1:3031 fd 3 Python version: 2.6.6 (r266:84292, Jun 18 2012, 14:18:47) [GCC 4.4.6 20110731 (Red Hat 4.4.6-3)] Set PythonHome to /opt/python-env/coefficient/ *** Python threads support is disabled. You can enable it with --enable-threads *** Python main interpreter initialized at 0xbed3b0 your server socket listen backlog is limited to 100 connections *** Operational MODE: single process *** added /opt/python-env/coefficient/lib/python2.6/site-packages/ to pythonpath. unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) *** no app loaded. going in full dynamic mode *** *** uWSGI is running in multiple interpreter mode ***` Note in particular this part of the log: unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) **no app loaded. going in full dynamic mode** This is my Flask app: from flask import Flask app = Flask(__name__) @app.route("/") def hello(): return "Hello, World, from Flask!" Before I added my Virtualenv's pythonpath to my configuration file, I was getting an ImportError for Flask. I solved this though, I believe (I'm not receiving errors about it anymore) and here is my complete configuration file: uwsgi: #socket: /tmp/uwsgi.sock socket: 127.0.0.1:3031 daemonize: /var/log/uwsgi.log pidfile: /var/run/uwsgi.pid master: true vacuum: true #wsgi-file: /var/www/coefficient/coefficient.py wsgi-file: /var/www/coefficient/flask.py processes: 1 virtualenv: /opt/python-env/coefficient/ pythonpath: /opt/python-env/coefficient/lib/python2.6/site-packages This is how I start uWSGI, from an rc script: /opt/uwsgi/uwsgi --yaml /etc/uwsgi/conf.yaml --uid uwsgi And if I try to view the Flask program in a browser, I get this: **uWSGI Error** Python application not found Any help is appreciated.

  Read the article

• Windows 8, IIS8 how to make PHP imagick work

  - by Laci K

  I'm new to IIS server before IIS for 6 years I used Apache 2.X and with Apache imageMagick and its PHP module imagick worked just fine even with x64 version of PHP and Apache 2.4 and imageMagick. I tried to make imagick to work with IIS8 but it wont work. I always get the typical PHP startup warning in my log PHP Startup: Unable to load dynamic library 'C:\Program Files (x86)\iis express\PHP\v5.4\ext\php_imagick.dll' - %1 is not a valid Win32 application. in Unknown on line 0 And the next thing why is IIS loading php from IIS express folder if I have php in the program files? But actually I dont care until it works :) So what I did so far I unistalled imageMagick 6.7.X 64bit version and installed the latest x86 version, tested it in command line and it worked, than I looked up on net the latest imagick DLL which was I think the 3.1.0RC2 (founded here http://www.peewit.fr/imagick/) than I copied the dll to PHP's ext folder than edited php.ini and added the imagick to the dynamic extensions after that I restarted IIS and than nothing :( I got the error which I wrote earlier. Today I installed PEAR package Installer because I read somewhere that someone made it work with it but he also mentioned, that he needed to comply wincache too. Isn't there any easier solutions to make it work? Could someone maybe write me a step by step guide how to make this work.

  Read the article

• nginx: SSI working on Apache backend, but not on gunicorn backend

  - by j0nes

  I have nginx in front of an Apache server and a gunicorn server for different parts of my website. I am using the SSI module in nginx to display a snippet in every page. The websites include a snippet in this form: For static pages served by nginx everything is working fine, the same goes for the Apache-generated pages - the SSI include is evaluated and the snippet is filled. However for requests to my gunicorn backend running a Python app in Django, the SSI include does not get evaluated. Here is the relevant part of the nginx config: location /cgi-bin/script.pl { ssi on; proxy_pass http://default_backend/cgi-bin/script.pl; include sites-available/aspects/proxy-default.conf; } location /directory/ { ssi on; limit_req zone=directory nodelay burst=3; proxy_pass http://django_backend/directory/; include sites-available/aspects/proxy-default.conf; } Backends: upstream django_backend { server dynamic.mydomain.com:8000 max_fails=5 fail_timeout=10s; } upstream default_backend { server dynamic.mydomain.com:80; server dynamic2.mydomain.com:80; } proxy_default.conf: proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; What is the cause for this behaviour? How can I get SSI includes working for my pages generated on gunicorn? How can I debug this further?

  Read the article

• How do i set up a fully featured small business network?

  - by JoshReedSchramm

  This has the possibility to be a very large question but I recently acquired a few rack mount servers and the hardware necessary to run them. Unfortunately I'm a programmer with very little understanding of how to set up a good working network so I'm hoping someone on here might be able to help. What I want to do is run a domain with a series of subdomains which would all be externally accessible. The setup would live inside my home and my internet connection is your run of the mill cable model (which means a dynamic IP) I want to be able to set up a couple site, specifically: www.mycompany.com (mycompany.com with no subdomain would redirect to this) build.mycompany.com (for my continuous integration server) ruby.mycompany.com (for ruby projects) win.mycompany.com (for windows project) etc. Additionally this is still my home network so our personal machines need to be able to get on via wifi with at least the same security we have now through an out of the box router from best buy. I'm thinking i need a DNS server, DHCP server and one of those would run either no-ip or dyndns to accommodate the dynamic ip. I don't necessarily need mail but it might be helpful to have some sort of mail server i could use for testing, it doesn't need to get out to the greater internet though. So how do i set up this kinda of network? tl;dr Need to know how to set up your standard office style network in my home off my normal consumer level cable modem connection.

  Read the article

• Enabling CURL on Ubuntu 11.10

  - by Afsheen Khosravian

  I have installed curl: sudo apt-get install curl libcurl3 libcurl3-dev php5-curl and I have updated my php.ini file to include(I also tried .so): extension=php_curl.dll To test if curl is working I created a file called testCurl.php which contains the following: <?php echo ‘<pre>’; var_dump(curl_version()); echo ‘</pre>’; ?> When I navigate to localhost/testCurl.php I get an error: HTTP Error 500 Heres a snippet from the error log: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/php_curl.dll' - /usr/lib/php5/20090626+lfs/php_curl.dll: cannot op$ PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/sqlite.so' - /usr/lib/php5/20090626+lfs/sqlite.so: cannot open sha$ [Sun Dec 25 12:10:17 2011] [notice] Apache/2.2.20 (Ubuntu) PHP/5.3.6-13ubuntu3.3 with Suhosin-Patch configured -- resuming normal operations [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/` Can anyone help me to get curl working? The problem was with the original test code. I used a new test file containing this and curl is now working: <?php ## Test if cURL is working ## ## SCRIPT BY WWW.WEBUNE.COM (please do not remove)## echo '<pre>'; var_dump(curl_version()); echo '</pre>'; ?>

  Read the article

• Multiple WAN interfaces on SonicWall TZ 100?

  - by Chad Decker

  I'm using a SonicWall TZ 100 with a basic configuration of X0 for the LAN and X1 for the WAN. The WAN uses DHCP to obtain its routable IP address. I want to obtain a second routable IP from my ISP. I'm in luck because my cable company will provide me with an additional dynamic IP for $5/mo. How do I bind this IP to my SonicWall? My additional dynamic IP will not be consecutive to the original one. It won't even be on the same class C. I think what I want to do is to use one of the empty ports/interfaces (X2, X3, or X4), tell that interface to use DHCP, and then add that interface to the WAN "zone". I can't figure out how to do this though. Here's what I've tried so far: (1) I've looked in Network Interfaces. I see X0 and X1 but the other unused interfaces don't show up. I don't see an "Add" button to add the new interfaces. (2) I've looked in Network Zones. I see that X0, X2, X3, X4 are in the LAN zone. I tried to drag X3 into the WAN zone but I can't. Nor does clicking the "Configure" button allow me to move an unused interface from LAN to WAN. (3) I've read the post entitled Splitting up multiple WAN's on Sonicwall. This doesn't seem applicable to me. Any thoughts?

  Read the article

• Uninstall php5 installed from source

  - by diegomichel

  I have tried to install php5 from source , and it worked... Then for some reason need to install the official packets, so i tried a make uninstall and for my surprise there is such make uninstall... so i tried delete all the installed files by hand. Then installed the official debian packages and it worked fine... till i need install sqlite module, which give me the following error: php --version PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626/pdo_sqlite.so' - /usr/lib/php5/20090626/pdo_sqlite.so: undefined symbol: php_pdo_register_driver in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626/sqlite.so' - /usr/lib/php5/20090626/sqlite.so: undefined symbol: php_pdo_register_driver in Unknown on line 0 PHP 5.3.1-5 with Suhosin-Patch (cli) (built: Feb 22 2010 22:46:05) Copyright (c) 1997-2009 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2009 Zend Technologies So i remember that manual install i did, and i think there is some old lib installed causing that problem, the bad thing is that there is not such make uninstall on the source code of php5... php-5.2.13 > make uninstall make: *** No rule to make target `uninstall'. Stop. I have tried reinstall and purge all php related packages via aptitude with not success. OS: Debian Squeeze. uname -a Linux desktop 2.6.32-trunk-amd64 #1 SMP Sun Jan 10 22:40:40 UTC 2010 x86_64 GNU/Linux Any idea how to fix that?

  Read the article

• qsub: How can I find out what DRM middleware exactly is installed on a cluster?

  - by gojira

  I have a user account on a very big cluster. I have previous experience with Grid Engine and want to use the cluster for array jobs. The documentation tells me to use "qsub" for load balancing / submission of many jobs. Therefore I assumed this means the cluster has Grid Engine. However all my Grid Engine scripts failed to run. I checked the documentation and it is a bit weird. Now I slowly suspect that this cluster does not actually have Grid Engine, maybe it's running something called Torque (?!). The whole terminology in the man pages is a bit weird for me as a Grid Engine user, for example they talk about "bulk jobs" instead of "array jobs". There is no referral to variables on which I rely on, like SGE_TASK_ID etc. Instead they refer to variables starting with PBS_. Still, there are qsub and qstat commands. Also qsub behaves differently, apparently it is not possible to specifiy the command line parameters with bash-script comments etc. There is a documentation for the cluster system, but it does not say what the DRM middleware actually is - it refers to the entire DRM system simply as "qsub". I tried qsub --version qsub: 1.2 2010/8/17 I am not sure what I am actually running when I invoke qsub on that cluster! My question is, how can I find out if I am running Grid Engine or Torque (or whatever it is), and which version?

  Read the article

• User authentication -- username mismatch in IIS in ASP.NET application

  - by Cory Larson

  Last week, an employee's Active Directory username was changed (or a new one was created for them). For the purposes of this example, let's assume these usernames: Old: Domain\11111 New: Domain\22222 When this user now logs in using their new username, and attempts to browse to any one of a number of ASP.NET applications using only Windows Authentication (no Anonymous enabled), the system authenticates but our next layer of database-driven permissions prevents them from being authorized. We tracked it down to a mismatch of usernames between their logon account and who IIS thinks they are. Below are the outputs of several ASP.NET variables from apps running in a Windows 2008 IIS7.5 environment: Request.ServerVariables["AUTH_TYPE"]: Negotiate Request.ServerVariables["AUTH_USER"]: Domain\11111 Request.ServerVariables["LOGON_USER"]: Domain\22222 Request.ServerVariables["REMOTE_USER"]: Domain\11111 HttpContext.Current.User.Identity.Name: Domain\11111 System.Threading.Thread.CurrentPrincipal.Identity.Name: Domain\11111 From the above, I can see that only the LOGON_USER server variable has the correct value, which is the account the user used to log on to their machine. However, we use the "AUTH_USER" variable for looking up the database permissions. In a separate testing environment (completely different server: Windows 2003, IIS6), all of the above variables show "Domain\22222". So this seems to be a server-specific issue, like the credentials are somehow getting cached either on their machine or on the server (the former seems more plausible). So the question is: how do I confirm whether it's the user's machine or the server that is botching the request? How should I go about fixing this? I looked at the following two resources and will be giving the first one a try shortly: http://www.interworks.com/blogs/jvalente/2010/02/02/removing-saved-credentials-passwords-windows-xp-windows-vista-or-windows-7 http://stackoverflow.com/questions/2325005/classic-asp-request-servervariableslogon-user-returning-wrong-username/5299080#5299080 Thanks.

  Read the article

• Why cache static files with Varnish, why not pass

  - by Saif Bechan

  I have a system runnning nginx / php-fpm / varnish / wordpress and amazon s3. Now I have looked at a lot of configuration files while setting up the system, and in all of them I found something like this: /* If the request is for pictures, javascript, css, etc */ if (req.url ~ "\.(jpg|jpeg|png|gif|css|js)$") { /* Remove the cookie and make the request static */ unset req.http.cookie; return (lookup); } I do not understand why this is done. Most of the examples also run NginX as a webserver. Now the question is, why would you use the varnish cache to cache these static files. It makes much more sense to me to only cache the dynamic files so that php-fpm / mysql don't get hit that much. Am I correct or am I missing something here? UPDATE I want to add some info to the question based on the answer given. If you have a dynamic website, where the content actually changes a lot, chaching does not make sense. But if you use WordPress for a static website for example, this can be cached for long periods of time. That said, more important to me is static conent. I have found a link with some test and benchmarks on different cache apps and webserver apps. http://nbonvin.wordpress.com/2011/03/14/apache-vs-nginx-vs-varnish-vs-gwan/ NginX is actually faster in getting your static content, so it makes more sense to just let it pass. NginX works great with static files. -- Apart from that, most of the time static content is not even in the webserver itself. Most of the time this content is stores on a CDN somewhere, maybe AWS S3, something like that. I think the varnish cache is the last place where you want to have you static content stored.

  Read the article

• AWS own email domain and some generic questions

  - by John Brunner

  I'm getting started with Amazon Web Services and I have a few question I'm not sure about. As every (company) webpage I want to use an "[email protected]" email adress, but how is that done? I looked up at godaddy.com (for domain registration), the offer me an email adress like I want, but for 3 dollars per month. Is this possible with AWS? Because at AWS you have just a complex domain which is not very userfriendly or serious. Also I want to host my dynamic webpage on the amazon cloud, but I'm not sure if I'm doing that right. I've read many guides, and all I know is that I have to purchase a Elastic Compute Cloud, and a Simple Storage Service... and every guide is working with the basic linux package, why not Windows? Is it more expensive? I just want to host a mySQL Server for the dynamic webpage, which is reached over a normal domain. And one last question, if I sign up for an AWS account it asks me for an email account. But I found it a little bit unserious to write there my free-webmailer-adress... How is it done the normal way? Thanks in advance! Best regards, john.

  Read the article

• Tools for displaying a multidimensional data table?

  - by ShreevatsaR

  [Apologies if this sort of question is off-topic for SuperUser. Please redirect to the right place if so.] There is a 3-dimensional array of values. (That is, instead of a table/2-dimensional array with values in a grid, the values can be thought of in a cube instead.) Is there a way to display this "cube" interactively, ideally on a webpage? Specifically, given the data, it would work something like this: the user selects two of the 3 variables. He then sees a "stack" of tables, one for each value of the third variable (cross-sections, in other words). By selecting the appropriate table from the stack, he can see the (i,j,k) value he wants. The "technology" for displaying such a thing (stacked tables, rotation, etc.) already exists, so this seems the sort of thing that someone ought to have written already. To be clear: I don't need sophisticated graphics necessarily, just the ability to select from cross-sections of variables. But I have no experience with (say, for displaying on a webpage) what web gadgets exist, so I'm clueless how to even search for one. (Google searches like "multidimensional data visualization" didn't throw up anything useful. Google Spreadsheets can do a few kinds of charts which can be embedded on a webpage, but I cannot tell if this is one of them.) [I can imagine how it ought to work for higher dimensions. For four-dimensions, instead of selecting just a stack, you'd first select an (i,j) from an "outer table", which would show all (k,l) values for that (i,j). For higher dimensions, inductively: you select (i,j), and then repeat what you'd do with 2 fewer dimensions.] So has this been written? Is this easy to write? Where ought one to look for such a thing?

  Read the article

• CMD/ADB - Autorun script to search, copy, and paste a file from android system to flash drive

  - by Outride

  I've looked around and can't find anything that answers my question. This is my first question, so any tips or thoughts are welcome, as well as an answer :p As explained in title, i want to create a script that launches, finds a file on android phone, copies it, and pastes it to a flash drive. As of right now, it's a mix of multiple tutorials, trial and error, and I'm at a point of giving up. As of right now, I have a flash drive, loaded with three scripts. As follows: Bold = name of file file.bat @echo off :: variables /min SET odrive=%odrive:~0,2% set backupcmd=xcopy /s /c /d /e /h /i /r /y echo off %backupcmd% "C:\Users\Outride\Desktop\kikDatabase.db" "%drive%\all" @echo off cls invisible.vbs CreateObject("Wscript.Shell").Run """" & WScript.Arguments(0) & """", 0, False launch.bat wscript.exe \invisible.vbs file.bat So far, I had to use android commander, manually go through the directory, find /data/data/kik.android/databases and then copy kikDatabase.db to my desktop. Then run this scrip. Yes i'm trying to pull the database to copy all my email contacts. I use launch.bat, which then makes file.bat invisible due to the invisible.vbs script. What would i need to do now to have the file searched for and copied to the flashdrive? Thanks in advance, i'll be glad to answer any questions if theres any :p just remember that i'm not exactly a tech expert haha EDIT* Cleared junk of prior edits. New - I now have a .bat script to recognize what drive the usb is on, and launch py_cmd (adb shell) This is the current script. pull.bat @echo off :: variables SET odrive=%odrive:~0,2% set launching=start "%drive%\Minimal ADB and Fastboot\py_cmd" echo off %launching% so how could I make it for the .bat or a new script, to type the following "adb pull /data/data/kik.android/databases/ %drive%\All\Database" into the adb terminal? please help! I've been racking my brain over this all night :3

  Read the article

• Multidimensional data table?

  - by ShreevatsaR

  [Apologies if this sort of question is off-topic for SuperUser. Please redirect to the right place if so.] There is a 3-dimensional array of values. (That is, instead of a table/2-dimensional array with values in a grid, the values can be thought of in a cube instead.) Is there a way to display this "cube" interactively, ideally on a webpage? Specifically, given the data, it would work something like this: the user selects two of the 3 variables. He then sees a "stack" of tables, one for each value of the third variable (cross-sections, in other words). By selecting the appropriate table from the stack, he can see the (i,j,k) value he wants. The "technology" for displaying such a thing (stacked tables, rotation, etc.) already exists, so this seems the sort of thing that someone ought to have written already. To be clear: I don't need sophisticated graphics necessarily, just the ability to select from cross-sections of variables. But I have no experience with (say, for displaying on a webpage) what web gadgets exist, so I'm clueless how to even search for one. (Google searches like "multidimensional data visualization" didn't throw up anything useful. Google Spreadsheets can do a few kinds of charts which can be embedded on a webpage, but I cannot tell if this is one of them.) [I can imagine how it ought to work for higher dimensions. For four-dimensions, instead of selecting just a stack, you'd first select an (i,j) from an "outer table", which would show all (k,l) values for that (i,j). For higher dimensions, inductively: you select (i,j), and then repeat what you'd do with 2 fewer dimensions.] So has this been written? Is this easy to write? Where ought one to look for such a thing?

  Read the article

• SWATCH - what am I doing wrong?

  - by Brian Dunbar

  What I want/need/desire is to log when a user logs into my FTP server. Problem: I can't make swatch work the way I should be able to. This data is logged to a file - but of course these logs are not kept very long. I can't keep the logs around forever, but I can extract data from then, analyze it, store results elsewhere. If there is a better way to do this than the following, I'm all ears. Swatch version 3.2.3 Perl 5.12 FTP: VSFTP OS (Test): OS X 10.6.8 OS (Production): Solaris From man I see I can pass contents to a command .. so I should be able to echo those values to file, do a sed/cut/uniq thing on them for stats. $ man swatch (snip) exec command Execute command. The command may contain variables which are substituted with fields from the matched line. A $N will be replaced by the Nth field in the line. A $0 or $* will be replaced by the entire line. Swatch file .swatchrc watchfor /OK LOGIN/ echo=red pipe "echo "0: $0 1:$1 2:$2 3:$3 4:$4 5:$5" >> /Users/bdunbar/dev/ftplog/output.txt" Launch with $ swatch -c /Users/bdunbar/.swatchrc --script-dir /Users/bdunbar/dev/ftplog -t /Users/bdunbar/dev/ftplog/vsftpd.log & Test echo "Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client "206.209.255.227"" >> vsftpd.log Results - it's echoing to TTY. This is not needed or desired on the server, but it does tell me things are working. ftplog *** swatch version 3.2.3 (pid:25780) started at Mon Jul 9 15:23:33 CDT 2012 Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client 206.209.255.227 Results - bad! I appear to not be sending the variables to text. $ tail -f output.txt 0: /Users/bdunbar/dev/ftplog/.swatch_script.25780 1: 2: 3: 4: 5:

  Read the article

• Using wildcard domains to serve images without http blocking

  - by iopener

  I read that browsers sometimes block waiting for multiple images from the same host, and I'm trying to do everything I can to speed up page load times. One caveat: I need to serve files over HTTPS. Any opinions about whether this is feasible: Setup a wildcard cert for *.domain.com. Whenever I need an image, generate an number based on a hash mod 5 of the filename, and append it to an 'img' subdomain (eg img1.domain.com, img4.domain.com, img3.domain.com, etc.); the hash will make any filename always use the same subdomain, and therefore the browser should be able to cache the images Configure a dynamic virtualhost record to point all img#. subdomains to /var/www/img I am looking for feedback about this plan. My concerns are: Will I get warnings when my page has https:// links to multiple subdomains? Is the dynamic virtualhost record I'm talking about even possible? Considering the amount of processing this would require, is it likely to even produce any kind of overall benefit? I'm probably averaging a half-dozen images per page, with only half being changed on each page refresh. Thanks in advance for you feedback.

  Read the article

• BIND: forward 1st level zone

  - by raven

  First of all: sorry for the language, English is not my primary language. I have star-like DNS structure with many filials (more that 2): ^ | v filialNS_1.filial_1.city.local <---- ns.main.city.local <---- filialNS_2.filial_2.city.local ^ | v ns.mail.city.local is slave of all filials zones filialNS_1 is master of filial_1.city.local filialNS_2 is master of filial_2.city.local filialNS_N is master of filial_N.city.local I want to: serve DNS queries for xxx.filial_N.city.local with filialNS_N.filial_N.city.local forward all queries for xxx.xxx.xxx.local from filialNS_N to ns.main.city.local forward other queries to our provider's DNS on filial (or google-public-dns or anything else) FILIAL CONFIG named.conf zone "filial_1.city.local" { type master; file "/etc/namedb/dynamic/filial_1.city.local"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "2.76.10.in-addr.arpa" { type master; file "/etc/namedb/dynamic/2.76.10.in-addr.arpa"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "local." { type forward; forward only; forwarders { <ns.main.city.local IP address> }; }; nslookup server.filial_1.city.local - works fine nslookup server.main.city.local Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find server.main.city.local: NXDOMAIN Where am I going wrong?

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >