Search Results

Search found 13457 results on 539 pages for 'superuser interface'.

Page 236/539 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

  • SQuirreL Client: Opening up a table in a separate tab

    - by Dalin Seivewright
    I've switched to SQuirrel Client to view an Oracle database with a variety of tables. At any given time, I need to look at the contents of several related tables at the same time. The problem is that, at least by default, SQuirrel Client does not open up multiple tables at a time. When you click on a different Table object, the main view is refreshed with newly selected table data. Oracle's SQLDeveloper (which I am trying to move away from) did this by default if I recall, but there was an option to "freeze" panes. Does a similar option exist in SQuirrel Client? I do not require the ability to view the contents of two different tables on the same screen (i.e. a split view) but I would like the ability to have tabs for each table so I can quickly switch between each table view rather then having to find the table in the table list over and over again. Note: I am using this in a professional capacity but if it does not "belong" here then I suppose it could be moved to superuser.

    Read the article

  • unable to access a NAT'ed IP via a VPN on Windows 7

    - by crmpicco
    I connect to a range of servers hosted by one provider via a VPN. I can connect to the VPN fine, however when I then go and try and connect to the server(s) it fails. A NAT'ed IP address that has worked up until today, has stopped working either via SSH/SFTP. As you can see below, if I try and ping the IP then it responds with Destination host unreachable, but, for some reason it says the reply is from 192.168.0.8? If it enter this IP address in my browser, I get nothing. Where is this IP coming from and is there any good reason why I cannot access the IP I am trying to ping? C:\Users\crmpicco>ping 172.26.100.x Pinging 172.26.100.x with 32 bytes of data: Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Ping statistics for 172.26.100.x: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), I have the VPN remote host address of 80.75.67.x, which shows me as being connected. But i'm unsure if there is a config issue at the server side or my end that has caused this issue? I have had some recent Win7 (automatic) updates, but it's hard to tell if that's caused this problem. This is my output from arp: C:\Users\cmorton>arp -a Interface: 192.168.0.8 --- 0xe Internet Address Physical Address Type 192.168.0.1 00-18-4d-b9-68-5e dynami 192.168.0.6 00-f4-b9-68-0c-9a dynami 192.168.0.7 08-00-27-f2-9f-d6 dynami 192.168.0.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 192.168.56.1 --- 0x15 Internet Address Physical Address Type 192.168.56.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 255.255.255.255 ff-ff-ff-ff-ff-ff static

    Read the article

  • Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

    - by Josh
    I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

    Read the article

  • tmpreaper, --protect and a non-root user

    - by nsg
    Hi, I'm a little confused. I have a download directory that I want to remove all files older then 30 days with tmpreaper. Just one problem, the directory in question is a separate partition with a lost+found directory, of course I need to keep it so I added --protect 'lost+found', the problem is that tmpreaper outputs: error: chdir() to directory 'lost+found' (inode 11) failed: Permission denied (PID 30604) Back from recursing down `lost+found'. Entry matching `--protect' pattern skipped. `lost+found' I have tried with other pattern like lost* and so on... I'm running tmpreaper as a non-root user because there is no reason for superuser privileges because I own all files (except lost+found). Are I'm forced to run tmpreaper as root? Or are my shell-skills not as good as I thought? I guess the problem is: tmpreaper will chdir(2) into each of the directories you've specified for cleanup, and check for files matching the <shell_pattern> there. It then builds a list of them, and uses that to protect them from removal. Any thought and/or advice? Edit: The command I'm trying to run is something like $ /usr/sbin/tmpreaper -t --protect 'lost+found' 30d /mydir 1> /dev/null error: chdir() to directory `lost+found' (inode 11) failed: Permission denied Edit 2: I read the source code for tmpreaper-1.6.13 and found this if (safe_chdir (dirname)) exit(1); and if (chdir (dirname)) { message (LOG_ERROR, "chdir() to directory `%s' (inode %lu) failed: %s\n", dirname, (u_long) sb1.st_ino, strerror (errno)); return 1; } So it seems tmpreaper needs to be able to chdir in to all directories, ignored or not. I see two options left Run tmpreaper as root Move the download directory Find a alternative tool (tmpwatch?) I will give it some more research before i make a choice.

    Read the article

  • Router reporting failed admin login attempts from home server

    - by jeffora
    I recently noticed in the logs of my home router that it relatively regularly lists the following entry: [admin login failure] from source 192.168.0.160, Monday, June 20,2011 18:13:25 192.168.0.160 is the internal address of my home server, running Windows Home Server 2011. Is there anyway I can find out what specifically is trying to login to the router? Or is there some explanation for this behaviour? (not sure if this belongs here or on superuser...) [Update] I've run both Wireshark and netmon for a while on my home server. Wireshark captured the traffic, but didn't really show anything useful (or nothing I could make use of). A simple HTTP GET request is sent from the server (192.168.0.160) to the router (192.168.0.1), from a seemingly random port (I've seen examples from 50068, 52883), and it appears to do it twice in quick succession (incrementing port by 1), about every hour. Running netstat around the time of the failure didn't show anything (probably too long after anyway). I tried using netmon as it categorises by process, so I thought it might show a corresponding process for the port. Unfortunately, this comes in under the 'unknown' category, meaning it's basically just a slower, less useful Wireshark. I know there's not much to go on here, but does this help in anyway?

    Read the article

  • iTerm2 vim cannot map alt key

    - by Eddy
    I'm having trouble trying to map the alt-key bindings on vim in iTerm2. I want to map shortcuts for switching between buffers like this: map <A-Right> <C-w>l map <A-Left> <C-w>h map <A-Down> <C-w>j map <A-Up> <C-w>k But I can't get it to work. I've tried everything, setting the option key as "Normal", "Meta" and "+Esc" in the profile settings. I've tried <M-Right> and <T-Right> but those don't work either. There are posts on superuser and stackoverflow but they use the old version of iTerm2 (v0.x). The only things I've managed to get working are <T-up> and <T-down>, or when I just use Macvim. I'm using iTerm2 v1.0.0.20120203, and Mac OS X 10.7.5 on a Macbook Pro.

    Read the article

  • Adjust output Brightness/Gamma/Colors in Gnome

    - by Mikee
    We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

    Read the article

  • Difficult to point-and-click target with Apple Magic Trackpad?

    - by Andrew Swift
    My Magic Trackpad is great for most things involving dragging and gestures, but for simple point-and-click use it is starting to get really annoying. For example, my bank has a numeric code that I need to enter from a visual grid on the screen, by clicking on the six numbers in order. To do this is quite difficult with the Magic Trackpad. Idea 1: it is because when you start dragging on the touchpad, there is a brief delay before the mouse starts to move. The delay might be enough to screw up my anticipation of where the cursor is going to go. Idea 2: it may have to do with the cursor acceleration. If I move it a little, the cursor moves a little. If I move it a lot, it goes much faster. I have tried various settings in the preference pane, and although the cursor does move more or less quickly, it doesn't seem any more or less easy to hit a given target. As I am writing this post, I tried a brief experiment -- I chose a spot on the page (the bracket in the superuser logo) and tried to move the cursor there in one quick movement. It's extremely difficult, even though I've been using Macs and touchpads since 1999. There is something about the behavior of the trackpad that is making it impossible for me to learn how to accurately predict where the cursor will end up. Does anyone else have this problem?

    Read the article

  • Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

    - by blaineh
    I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

    Read the article

  • How do I Implement VLAN Rate Limiting or QOS for a Cisco 2960?

    - by evolvd
    I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

    Read the article

  • Any way to map WebDAV with SSL as network drive in Windows XP?

    - by Shadow
    I'm trying to map WebDAV with SSL as a network drive in Windows XP. (I've been at this for several hours) I can read the share just fine using a browser and with Network Places, but it refuses to mount as a network drive. I've tried it using the Windows explorer interface and net use. Net use with the \\server@ssl:443\webdav method gives System error 53. https://server/webdav gives error 67. Any help would be appreciated.

    Read the article

  • Virtualbox - routing subnet to bridge adapters

    - by user42384
    Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

    Read the article

  • How can I recover my ext4 ubuntu partition from my windows parition?

    - by officespace
    I dual boot windows and ubuntu 10.04. I accidentally did an rm -r * in my home directory and deleted a bunch of files and folders that I need to recover. How can I recover these files from my windows xp partition? If there's isn't a way to do this from windows, what's the best way to do it in ubuntu? I'd prefer a graphical interface if that's possible. I appreciate the help.

    Read the article

  • How to edit a table in the email reply (in Gmail)?

    - by imz
    I've received an email with an embedded table. I want to put some marks inside that table (i.e., edit the contentof the table) and send it back. Unfortunately, the Gmail interface doesn't seem to have table editing capabilities: after I hit reply, I see the table in the quoted text of the original message, but is not editable... If this is not possible in Gmail, how do I export the HTML source of this messsage and edit in another installed word processor?

    Read the article

  • Telugu (unicode) font rendering in emacs

    - by Prakash K
    [I asked the following question in stackoverflow, and I have been redirected here. I hope I can get some answers here. My question at stackoverflow had two small images showing the example rendering of text. As a new user at superuser, I am not being allowed to include them here, nor I am allowed to post more than one hyperlink. And, I don't have enough reputation on SO to migrate that question. Please look at the stackoverflow question for the images. Sorry about the inconvenience.] I sometimes edit text in telugu language. However, when I open the file (UTF-8 encoded) in GNU emacs (version 23.1.50.1 on Ubuntu Jaunty) the text rendering is incorrect. The same text file opened in gedit is rendered correctly. Here's a snippet: ????????? ???? ???? ???????? rendred in gedit: Please see the SO question for the image showing telugu text rendering in gedit And, the emacs rendering of the same text: Please see the SO question for the image showing telugu text rendering in emacs Wherever glyphs need to be composited (not sure if it's the right word), emacs (or whatever library it uses) is not doing it right. Is there anyway to fix this? Perhaps tuning some setting in my configuration? Any ideas, please?

    Read the article

  • Multiple virtual VLAN interfaces on single NIC (Debian)

    - by RayQuang
    I'm trying to setup multiple virtual interfaces with VLAN's on a single NIC. I'm running Debian Squeeze. Currently this is my /etc/netowrk/interfaces auto eth0.10 iface eth0.10 inet dhcp This gives me a working connection, however I'm not sure how to configure several like these on a single NIC so I can use multiple external IP's. I have tried aliasing the VLAN's like so: iface eth0.10:1 But that was not successful and it said failed to bring up interface. And suggestions would be greatly appreciated :)

    Read the article

  • External HDD incorrectly detected as internal - how change to enable hot swap/eject?

    - by Sam
    Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

    Read the article

  • Routing table with two NIC adapters in libvirt/KVM

    - by lzap
    I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

    Read the article

  • Difficult to point-and-click target with Apple Magic Trackpad?

    - by Andrew Swift
    My Magic Trackpad is great for most things involving dragging and gestures, but for simple point-and-click use it is starting to get really annoying. For example, my bank has a numeric code that I need to enter from a visual grid on the screen, by clicking on the six numbers in order. To do this is quite difficult with the Magic Trackpad. Idea 1: it is because when you start dragging on the touchpad, there is a brief delay before the mouse starts to move. The delay might be enough to screw up my anticipation of where the cursor is going to go. Idea 2: it may have to do with the cursor acceleration. If I move it a little, the cursor moves a little. If I move it a lot, it goes much faster. I have tried various settings in the preference pane, and although the cursor does move more or less quickly, it doesn't seem any more or less easy to hit a given target. As I am writing this post, I tried a brief experiment -- I chose a spot on the page (the bracket in the superuser logo) and tried to move the cursor there in one quick movement. It's extremely difficult, even though I've been using Macs and touchpads since 1999. There is something about the behavior of the trackpad that is making it impossible for me to learn how to accurately predict where the cursor will end up. Does anyone else have this problem?

    Read the article

  • Intel GMA 965 M - OpenGL missing

    - by pestaa
    I have a Lenovo 3000 N200 notebook with integrated GMA 965 VGA, using Windows 7. All my drivers are up to date, downloaded directly from the vendor site, installed with administrative privileges, etc. Yet, all OpenGL applications cannot render the interface (or any visuals). Examples are Blender (3D modeling software) and Babo Violent (top-down FPS). All the controls, sound effects and music are live, but the screen is black or light gray, respectively. What can one do?

    Read the article

  • Add drupal modules on ec2 server

    - by CQM
    how do I add external drupal modules to an ec2 server? Drupal interface wants me to provide ftp password, but amazon ec2 uses private key pair and not username/password (unless I enable that, which I don't want to) how would I install from a site like this http://drupal.org/project/restws if the automated way is not feasible, do I just have to upload the individual module files to a particular drupal folder via sftp?

    Read the article

  • Data recovery from corrupt Ubuntu partition/directory (question about a previous answer)

    - by JoshMaurice
    I have an Ubuntu installation that won't boot anymore. I asked my previous question about it here: http://superuser.com/questions/15916/ubuntu-chkdsk-equivalent Bolotov replied: As I see from your previous question you can boot Windows so you could use dskprobe from Windows XP Service Pack 2 Support Tools to make sure that fs type is correct ... but it's already correct fs type 7 is NTFS. Message "The type of the filesystem is RAW. CHKDSK is not available for RAW drives." means that windows can't determine fs type for some reason. As we see fs type is correct. To run Chkdsk on your Windows partition you can install Windows Recovery Console, boot in recovery console and check your disk. After checking the disk you will gain access to you c:\ubuntu\disks. I think you can mount your linux partition (which is in file) as usual loop-back device: mount -o loop [path to your linux-loopback-partition] But you should mount windows patrition first. So now I'd like to know: Within the recovery console I will be issuing the commands "chkdsk -r" and then "mount -o loop [path to windows partition]" and then "mount -o loop c:\ubuntu\disks", correct? I do have a ("corrupt and unreadable") c:\ubuntu\disks directory so that appears to be the correct path to the linux partition; do you know the path to the windows partition? would that be just "c:\"?

    Read the article

  • Suggestion for software to control internet

    - by redknight
    I need to implement a gateway that will allow me to control the access to the internet of a network made up of a about half a dozen of workstations. My main obejectives are the following: 1- Monitoring of traffic 2- Logging of traffic 3- Access control - block websites (mainly adult) and certian traffic(example torrents) 4- Possibly cache content 5- Easy management interface 6- Preferable free and opensource Serverfault users can you please suggest from your vast experience which software you think is the best to suit my needs? Any suggestion is greatly appreciated. Thank you

    Read the article

  • Release/Renew IP Address via Terminal in OS X

    - by Rupert
    I am looking to release and renew my IP address in OS X 10.4 using Terminal. Essentially, I need the OS X equivalent of Windows: C:\ ipconfig /release C:\ ipconfig /renew However, I need the interface to remain active during this process, so using ifconfig down/up will not work. I believe I can clear the IP with ifconfig delete but I'm not sure how to get the dhcp client to reassign the address. An article from 2002 suggests using set dhcp but Apple's ifconfig man page does not include this information.

    Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >