Search Results

Search found 13457 results on 539 pages for 'superuser interface'.

Page 237/539 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Find more than one string with Excel?

  - by ramsespiso

  How to Find more than one string with Microsoft Office Excel with the graphical interface? For example, I am looking for the cells which is contained both strings Paul and John?

  Read the article

• What's the difference between DisplayPort, DVI and HDMI?

  - by Leo Bushkin

  As an end consumer, are there any significant differences between the newer DisplayPort interface and DVI/HDMI that I should be aware of? I realize they are different connector types and require compatible equipment, I'm primarily interested in whether there are functional or performance benefits of one technology over another. Should I have a preference for one technology or another on newer video card equipment?

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Export/Import Windows XP wireless configs

  - by blunders

  About to rebuild my XP install and figured I'd see if there was a file or interface for collecting the configs for the built in Windows XP wireless manager. I've looked under the "advance settings" tab and within the properties GUI for each connection and I'm not seeing a way to export the configs. Clearly if I'm exporting these I'd like to be able to import or override the default config with the backup.

  Read the article

• How to install couchdb on mac osx 10.6

  - by Adam

  I'm trying to install CouchDB on my mac, running snow leopard 10.6. I installed Xcode, MacPorts, and then followed the instructions here: http://wiki.apache.org/couchdb/Installing_on_OSX It all worked fine until I tried to visit the web interface: http://127.0.0.1:5984/_utils/index.html Google chrome said "Oops! Google Chrome could not connect to 127.0.0.1:5984" I tried connecting using telnet in bash and it said connection refused. Can somebody shed some light with some suggestions or perhaps and idiot-proof walkthrough?

  Read the article

• How to remove extensions from "Name" column in Freecommander?

  - by NoCanDo

  In order for me to switch from TotalCommander to FreeCommander, I need to have an excact replica of the interface I've been using for almost a decade. I need to remove the extrensions from filenames in the Name-Column. This is how it looks in my FreeCommander: And this is how I need it to look:

  Read the article

• Delete data from a SQL Server database on a full partition

  - by aleroot

  I have a SQL Server 2005 Database on a dedicated partition, during the time the database grown and now it have occupied all the space on the partition, now the problem is that the only operation I can do on the database is detach, but i want to remove old data from some tables to save space ... How can I remove old data from the database if SQL Server interface doesn't allow to run queries on it ?

  Read the article

• How can I merge partitions of a USB flash drive?

  - by Billy

  I have this USB flash drive which has two partitions separated by the manufacturer. The interface included doesn't allow me to merge them and I was wondering if someone has come across such problem.

  Read the article

• Word 2007(2010) Viewer

  - by Jox

  Does Word Viewer 2007 exists (with new Ribbon interface)? I ask this because only thing I found so far is Word Viewer 2007 as a Viewer 2003 with compatibility packs (which looks like standad Office 2003), but that doesn't works very well for my documents. Thanks

  Read the article

• linux macvlan - stop from broadcasting hostname

  - by staticfloat

  I am trying to simulate two different computers on one box, using the macvlan module (which is awesome, by the way) but I have one small problem; When I create the macvlan Ubuntu 11.10 very helpfully starts broadcasting its hostname on both interfaces, creating an amazing amount of confusion for everything that deals with hostnames. Does anyone know how to stop ubuntu from advertising its hostname on a certain interface? Thanks!

  Read the article

• best app to stream movies over the web

  - by rashcroft

  Hi. I have an old box that I'd like to use as a private sever to stream movies off of. My upload speed is about 0.5/Mb/s, so I need something that compresses well. I'd like to be able to access these movies from anywhere, through the web, through some interface (maybe the divx web player? flash player? some other protocol?) Can anyone recommend anything good? (Using Windows XP) Thanks!

  Read the article

• CPU operating temperature ranges

  - by osij2is

  I have an AMD Phenom II 960T with 2 cores unlocked for a total of 6 cores. I don't overclock at all. I have a Arctic Cooling ACALP64 Heatsink/Fan installed. I'm currently running ESXi 5.0 so I have to go into the BIOS to read the CPU temperatures, which at idle seem to be in the 71-74C range. To me, this is pretty high, but I cannot find any official temperature ranges that AMD says the CPU can work well within. There seems to be a lot of questions on superuser and numerous forums around CPU temperatures but no one seems to have a clear consensus as to what the manufacturer temperature ranges are for specific CPUs. I've tried searching through AMDs site to no avail. At this point, I'd be willing to shut off the 2 extra cores if it keeps the heat down but until I get some sort of tolerance or range for temperature, I have no idea if the CPU is being damaged or not. Can anyone point to a direct source, article, FAQ from AMD that specifically states their CPUs temperature range? Or are CPU temperature ranges so varying that there's no possible baseline? Am I being too paranoid about this? To me, anything over 65C is a bit much and if I'm in the low-mid 70s range with NO VMs running, what can I expect if I have several VMs running?

  Read the article

• Can Windows 7 Built-in VPN Replace Cisco VPN?

  - by Brandon Wang

  Is there any way that the built-in VPN interface in Windows 7 can replace the rediculous Cisco VPN software? I have tried several times using different methods and have failed. It seems if you just plug in the IP addresses and information it doesn't work.

  Read the article

• cisco 2851 router: can't view switch ports

  - by red888

  I want to setup vlans on a 2851, but I'm not sure how to access the switch ports. I can access or view them. Is there something I have to enable? I have some devices plugged into the switch ports and they are communicating with each other fine. router(config)#do show ip int bri Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES NVRAM administratively down down GigabitEthernet0/1 unassigned YES NVRAM administratively down down GigabitEthernet1/0 10.1.1.1 YES manual up up

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Routing between 2 different subnets on 2 different interfaces in SonicOS

  - by Chris1499

  I'm having a bit of a problem allowing traffic between two of my subnets. Here's the structure I've built. The X0 interface has our windows server on it and it handles DHCP/DNS, etc. X1 has the WAN connection. The Sonicwall is handling DHCP on X2. The X3 interface is connected to a different vlan on the 48 port switch. The Sonicwall is handling DHCP on this network as well. So here's what i want to do. The network on X2 is for our guest wireless; i don't want it to be able to access any of the other networks, just the internet, so i that all blocked in the firewall. No issues there. The X3 network is going to be for programmable controllers, and needs to be able to access the X0 network where our computers are. This is where my problem is. I'm not able to get between the 192.168.2.xxx and the 192.168.1.xxx on interfaces X0 and X3 respectively. I have these rules set up in the firewall. The Lan Primary Subnet is the 192.168.2.0 on X0. So if i'm not mistaken, this will allow traffic between the two through the firewall. Now this is where I'm a little confused. Do i need to use NAT to get the traffic from X0 to go to X3 (and vice versa), or a static route, or both? Currently i have both, though i doubt they're done correctly (also in screenshot). I've tried to ping between the two without luck. Any advice, or if you see what's wrong with my setup, is much appreciated. If you need some more information, let me know. Thanks all! EDIT: So i found that i don't neither either NAT or a static route, that the setting in the firewall is enough. I can now ping from the 192.168.1.xxx network, however i can't access the server on the 192.168.2.xxx network. When i try to access i get "An error occured while reconnecting to Z: to server Microsoft Windows Network: The local device name is already in use. This connection has not been restored. What am i missing?

  Read the article

• How do I Implement Per VLAN Rate Limiting or QOS for a Cisco 2960?

  - by evolvd

  I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

  Read the article

• Assist me access my firewall using ASDM

  - by ghp

  Have configured my asa 5520 with all the interfaces inside -- 10.11.12.1 outside - 70.71.72.4 Have not connected the management interface ..left it as is. Im remotely accessing this firewall from a different location by SSH, but would like to use the asdm to access it remotely. I have configured the HTTP SERVER enable and assigned http 10.11.12.254 255.255.255.255 inside Please can someone let me know the config which can help me access this firewall using ASDM.

  Read the article

• TortoiseSVN client slows Explorer to a crawl in Windows XP running in Parallels

  - by Cory Larson

  I thought I'd make my first SuperUser question relatively simple, though it's the kind of question that may not get many responses as I'm not directly involved with the issue. A colleague does his development in Windows XP running in Parallels on his Mac. We've just migrated our VSS repository to SVN, and we've gone with TortoiseSVN as our client of choice with the Ankhsvn plugin for Visual Studio. On his XP instance, after installing TortoiseSVN, browsing through folders using Explorer is extremely slow; about 15 - 30 seconds before the contents of the next folder displays. It's the slowest when opening My Computer. Once he reaches a folder that contains the working content of an SVN project, Explorer behaves quickly again as expected. It seems that TortoiseSVN may be spending a bunch of time searching subfolders for stuff so it can do its icon-overlay thing, but that's just a guess. I've used TortoiseSVN for years on both XP and Vista on far less powerful machines without any issues with Explorer, so I'm attributing the slowness to it being run in a VM, though that may not be the actual issue. So has anyone encountered similar performance issues, and/or know of a fix? Keep in mind that any requests to make changes to his configuration will need to be communicated and thus my response time might be slow. Thanks everyone!

  Read the article

• Use preforker(ruby gem) with supervisor

  - by user1548832

  I also asked same question on stackoverflow.com http://stackoverflow.com/questions/13871169/use-preforkerruby-gem-with-supervisor But, superuser.com might much help to me. Can anyone amswer this? I want to run a server program using preforker ruby gem with supervisor. But error has occured. I wrote a following test program using preforker. #!/usr/bin/env ruby require 'rubygems' require 'preforker' Preforker.new(:app_name => 'test-preforker', :timeout => 60, :workers => 1) do |master| while master.wants_me_alive? do puts "hello" sleep 10 end end.run And a following supervisor config. [program:test-preforker] command=/home/tkono/tmp/test-preforker.rb stdout_logfile_maxbytes=1MB stderr_logfile_maxbytes=1MB stdout_logfile=/var/log/%(program_name)s.log stderr_logfile=/var/log/%(program_name)s.log autorestart=true Then, reload supervisor. # supervisorctl reload Restarted supervisord Here is the log file of supervisor. 2012-12-13 17:50:47,161 CRIT Supervisor running as root (no user in config file) 2012-12-13 17:50:47,163 WARN Included extra file "/etc/supervisor.d/test-preforker.ini" during parsing 2012-12-13 17:50:47,209 INFO RPC interface 'supervisor' initialized 2012-12-13 17:50:47,213 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2012-12-13 17:50:47,215 INFO supervisord started with pid 12437 2012-12-13 17:50:48,231 INFO spawned: 'test-preforker' with pid 12440 2012-12-13 17:50:48,233 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:49,248 INFO spawned: 'test-preforker' with pid 12441 2012-12-13 17:50:49,261 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:51,267 INFO spawned: 'test-preforker' with pid 12442 2012-12-13 17:50:51,284 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:54,305 INFO spawned: 'test-preforker' with pid 12443 2012-12-13 17:50:54,308 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:55,311 INFO gave up: test-preforker entered FATAL state, too many start retries too quickly Please tell me what is wrong? A program using preforker cannot run with supervisor? preforker https://github.com/dcadenas/preforker supervisor http://supervisord.org/index.html

  Read the article

• Monit Webmin service is not activating

  - by Nagaraj

  I have written a script in monit interface for Webmin service. I can execute the process wherien I am unable to restart the service. check process webmin with pidfile /var/webmin/miniserv.pid start = "/etc/init.d /webmin start" stop = "/etc/init.d /webmin stop" if failed host in1.miracletel.com port 10000 then restart if 5 restarts within 5 cycles then timeout #if changed pid 2 times within 2 cycles then aler Would you please look into this and let me know, whether I can considered the service correct or not?

  Read the article

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• School Management System

  - by BoundforPNG

  I am looking for a school management system to replace a homegrown Access db. It should be able handle the following for both a Primary and Secondary school Scheduling classes Student Enrollment Allow teacher to enter grades and comments Generate transcripts and report cards Handle attendance Handle tuition billing It should store data in a server database like SQL Server and it would be nice to have a web interface. We are open to a commercial system or an Open Source system that comes with support.

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >