Search Results

Search found 11759 results on 471 pages for 'isolation level'.

Page 238/471 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

  - by user223833

  I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

  Read the article

• Dell Vostro 3500 battery life remaining missing from Windows 8?

  - by Misha

  On Windows 7 a Vostro 3500 laptop shows the battery life remaining, while on Windows 8 this information appears to be missing. The percentage is still available, but the life remaining is missing. How is battery life remaining calculated and does this require some level of driver support? Is it a standardized interface? Does anybody know which driver is responsible for handling this feature? I want to force the old Windows 7 driver, but I don't know which driver does battery remaining.

  Read the article

• How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• CentOS 6 init script doesn't work properly

  - by user711643

  I'm setting up my ruby production server based on CentOS 6. I need a process called god (which is a process monitoring tool) to start at boot. I'm using an init script that I found here. Just as stated in the guide I ran: chkconfig --add god and then chkconfig --level 345 god on After this if I run "service god start|restart" everything works. It loads the available configurations and brings up the related processes (if they are not running). Problem is it doesn't work at boot. If I reboot the system, then I do "ps -aux | grep god". At this point "god" is running but apparently it didn't load the configuration files. If i run again service god restart, it loads everything without problems. What am I doing wrong?

  Read the article

• Replicate a big, dense Windows volume over a WAN -- too big for DFS-R

  - by Jesse

  I've got a server with a LOT of small files -- many millions files, and over 1.5 TB of data. I need a decent backup strategy. Any filesystem-based backup takes too long -- just enumerating which files need to be copied takes a day. Acronis can do a disk image in 24 hours, but fails when it tries to do a differential backup the next day. DFS-R won't replicate a volume with this many files. I'm starting to look at Double Take, which seems to be able to do continuous replication. Are there other solutions that can do continuous replication at a block or sector level -- not file-by-file over a WAN?

  Read the article

• Need recommendations for a hardy scanner that has a robust feeder tray

  - by JohnyD

  In the early days of our company all our information came in on paper and all of what we sold was on paper. Because of this we literally rent our an old bank vault to house the millions of sheets of paper that, some say, still contain relevant information. That being said, I'm looking into purchasing some hardware capable of scanning all these documents and converting them to pdf. Being new at this level of digitization I would like to ask for recommendations for accomplishing this task. Most of this material exists as separate bound studies/articles/etc. Someone would have to remove the bindings and be able to load many pages at a time and have the scanner feed them all through and convert them to a single pdf (single pdf per study/article/etc). If you have any recommendations I would very much appreciate hearing about them, thanks.

  Read the article

• How to block null/blank user-agents in IIS 7.5

  - by Jeremy

  We are going through a large scale DDOS attack, but it isn't the typical bot-net that our Cisco Guard can handle, it is a BitTorrent attack. This is new to me, so I am unsure how to stop it. Here are the stats IIS is processing between 40 and 100 requests per second from BitTorrent clients. We have about 20% of the User Agents, but the other 75% are blank. We want to block the blank user agents at the server level. What is the best approach?

  Read the article

• How do I get rid of the Cisco CP one-time user message on a Cisco 2901 router?

  - by user65712

  I get this message on a new 2901 Cisco router: Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session. It is strongly suggested that you create a new username with a privilege level of 15 using the following command. username <myuser> privilege 15 secret 0 <mypassword> Replace and with the username and password you want to use. It appears every time I login and everytime I show run. I already set up my username. How do I turn it off?

  Read the article

• Strange Intermittent Background Sound in Windows 7

  - by NoCarrier

  Ok, this is very strange. Recently, i noticed that every 10-15 seconds, there would be this faint, annoying duh-dum sound coming out of my speakers. (hard to describe. sounds somewhat like the sound windows makes when you unplug a USB device, but not as pronounced and much quieter). I closed every app and ended as many processes as I could, but the sound persists. I look at the volume mixer and sure enough, when the sound occurs, there is a little spike in the level under "System Sounds". I haven't installed any hardware or software in the last several weeks. This started recently - completely out of the blue. Does anyone have any insight?

  Read the article

• Programmatically change height of the window more than the height of the screen in Mac OS X

  - by nezlooy

  Respected low-level users of Mac OS, please, help. I'm trying programmatically to change height of window of safari (or other window). I'm was trying used AppleScript and AXUIElementSetAttributeValue of Carbon, but none of these methods can't increase the window bigger than the height of the screen. But, the width changes without any problems. I guess I'd be starting with something like SetWindowPos with SWP_NOSENDCHANGING flag under Win32. Maybe, you can disable this functionality, which monitors the size of the window or completely shutdown the one who is responsible for it? Note that I want to do this programmatically from an external process - I'm not asking how to control just my own app's window size and position. Thanks.

  Read the article

• Automatically make or update a copy real-time on another hard drive volume whenever files are saved to a particular folder

  - by mrblint

  Whenever I save or update a file to a particular designated folder on my C:\drive I would like to make or update a copy on my network-attached storage device, ideally saving the copy to the NAS as a version rather than overwriting a copy there, if possible. I have Windows 7 x64 Ultimate. Is there any feature built-in that can accomplish this? It has to be a real copy, not merely a pointer. I'm trying to achieve some redundancy for especially critical documents (in a variety of formats) that change frequently throughout the day. P.S. I am looking for folder-level granularity; I wouldn't want this to happen for every file on the C: volume.

  Read the article

• Can I use VT-D with a windows host for a VM?

  - by Journeyman Geek

  I've got a fairly beefy gaming system that I also run occational virtual machines on. It runs windows 8 and the built in hyper V virtual machine software at the moment and has a core i7 3770 (which unlike the unlocked model, should support VT-D), an Asus P8Z77V and a gforce 660 video card(also asus). I figure that if I could use VT-D I could add a cheap dedicated 3d card for a VM, in case I wanted somewhat more than the 'basics'. I know KVM and Xen support this to some level on linux, but can I do so on windows? I'm open to switching VM software if need be.

  Read the article

• Restrict only some plugins to specific sites in Google Chrome

  - by Christian

  I am looking for a way to set up Google Chrome so that it will run a certain plug-in (Java, what else?) only on whitelisted sites, but other plug-ins (like the PDF viewer) everywhere. From playing with the policies available for Chrome, I think there are basically two levels of plug-in management: List of disabled plugins/enabled plugins: Controls whether a plug-in exists for the browser at all This pair of policies applies to plug-ins, but not to sites. Default plug-in settings/Allow plug-ins on sites: Controls on which sites plug-ins can run This set of policies applies to sites, but not to individual plugins, and it cannot override the first pair. There appears to be no way to configure Chrome so that some plug-ins only run on whitelisted sites, but others run everywhere by default. I have also looked at filtering content on the firewall/proxy level, but I'm not convinced it can be done securely there. Filtering by URLs (file names) or content types can be circumvented trivially, and identification by content inspection cannot be safe either.

  Read the article

• Iptables rules make communication so slow

  - by mmc18

  When I have send a request to an application running on a machine which following firewall rules are applied, it waits so long. When I have deactivated the iptables rule, it responses immediately. What makes communication so slow? -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p esp -j ACCEPT -A INPUT -i ppp+ -j ACCEPT -A INPUT -p udp -m udp --dport 500 -j ACCEPT -A INPUT -p udp -m udp --dport 4500 -j ACCEPT -A INPUT -p udp -m udp --dport 1701 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i lo -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A FORWARD -i ppp+ -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT

  Read the article

• What IT certification is most valuable without job experience? [closed]

  - by Eric Wilson

  I'm trying to change vocations towards IT. I'm learning JAVA, SQL, and other things, but I have no job experience or formal education (other than a math Ph.D.) I know that certifications only go so far, but I was curious which certifications might be the most valuable for a first IT job? To clarify my question: Oracle certification + Zero Oracle experience = 0% chance of Oracle DBA job. Perhaps, though: [foobar certification] + Zero IT job experience = nonzero chance of entry IT job? Please give specific suggestions of certifications that you would consider relevant towards an entry-level IT job.

  Read the article

• What is name server of my domain, pointing to hosted site on Github Pages?

  - by nournia

  I've got one domain name and I want to set it up for my hosted site on Github Pages service. In the documentation this point is mentioned that If you are using a top-level domain like example.com, you must use an A record pointing to 204.232.175.78. But my domain registrar doesn't permit me to add a DNS Record. But only asks me to fill one table like this: Name Server (NS Record) Server Name ......... | Server IP ns53.parsihost.com | 94.232.173.52 ns2.parsihost.com | 206.223.171.254 I asked the registrar about this problem and they said to me "You must put Github's name server in those cells". So, what is the mapping from this table to DNS Records, and what is your advice for filling this kind of table?

  Read the article

• Missing files when Windows 7 returns from hibernate w/ dual boot

  - by Arthur N

  I have a dual-boot setup with Ubuntu (lucid) and Windows 7. I have the Windows file system shared on Ubuntu through Samba. Occasionally, I am working on Windows and my machine will go into hibernate (i.e. when the battery level is critical). By default, my GRUB settings boot me into Ubuntu. So when I get back to my PC, sometimes I just hop into Ubuntu instead of going back to Windows. However, if I write any files to the Windows file system during that Ubuntu session, the next time I do go back to Windows (which resumes from hibernate), those files are missing. Obviously, the state of the actual file system and the hibernate snapshot become out of sync, and Windows chooses the hibernate snapshot, overriding any changes I may have made thru Ubuntu. For now, I've disabled the hibernate option in the Windows power settings, but is there any utility I can use to get back some of those missing files?

  Read the article

• Restrict Apache to only allow access using SSL for some directories

  - by DrStalker

  I have an Apache 2.2 server with an SSL certificate hosting several services that should be only access using SSL. ie: https://myserver.com/topsecret/ should be allowed while http://myserver.com/topsecret/ should be either denied or, ideally, redirected to https. http://myserver.com/public should not have this restriction, and should work using either http or https. The decision to allow/deny http is made at the top level directory, and affects all content underneath it. Is there a directive that can be placed in the Apache config to retrict access in this manner?

  Read the article

• How to change the setting for a network device reported by ethtool, specifically Speed, on VM?

  - by Ramadheer Singh

  This is related to these two questions, although they don't answer my question. The machines are RHEL6. 1.ethtool not showing all the properties 2.changing network speed to 1000Mb/s Output on VM: [root@foo ~]# ethtool eth0 Settings for eth0: Current message level: 0x00000007 (7) Link detected: yes Output on Real Hardware: (interested in Speed) # ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes ***Speed: 1000Mb/s*** Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: d Wake-on: d Link detected: yes if there's anyway I can set this in VM, please suggest.

  Read the article

• How do I know if I need a layer 3 switch?

  - by eekmeter

  We currently have a flat network with a bunch of unmanaged switches. I would like to use VLANs to segregate certain users like guests and I would like to use 802.1x. However, I'm not sure if what I need is a layer 3 or a level 2 switch. From what I understand a layer 3 switch does routing between VLANs. I don't think I need this at the moment but as I said I'm not sure since this is all new to me. What else would a layer 3 switch do for me? Our network is relatively small, less than a 100 users. What exactly does a layer 3 switch do that I can't get with a layer 2 switch? When would I need a layer 3?

  Read the article

• How to troubleshoot Application Popup issues 0XC0000142 and 0XC000009a

  - by DotDot

  I am running randomly into 1 of these popups when our application runs. The machines range from 8GB/8Core to 24GB/24Core and run Windows Server 2008 R2. The application is a bunch of perl scripts and exe's that are expected to utilitize the server well. The process tree can be quite deep (5-6 child levels) and quite broad (60-70 level 1 processes). We hit this issues every 1% run on random machines. The application stalls on popup, unless someone clicks the damn button. The event log reads as cmd.exe - "Failed to initialize app. Click OK to close app" How could I reliably repro these issues?

  Read the article

• How to increase the volume gain when viewing online flash video?

  - by Nick000

  When watching online Flash videos on Youtube, Dailymotion, etc... sometimes the videos are recorded at low volume. The thing is that, I have a HP Notebook with good enough audio volume, but when I watch these "low volume" videos the sound level is really low, even when I have the volume at 100%. So I am looking for a way to increase the volume gain (like VLC player where you can increase it to 200%), BUT while watching it live on Youtube... that is, I don't want to download the video on my PC. Is there a software that can do that? Maybe an advanced flash video player that integrates to browser? or some other software to increase the volume gain overall on my laptop? My Specs: HP Pavilion Notebook, Audio: IDT High Definition Audio CODEC (integrated), Vista 64-bit, 4 GB RAM, etc.....

  Read the article

• Problem Writing to Samba Share

  - by Chris

  Hello, I have had a problem writing to a Samba Share I believe you have the answer in this post that you posted in October. Can you tell me how to do this? Thank you very much "On the Samba server, you need to ensure that the nobody user has write permissions to /Windows_Backups/DC. You're forcing everyone to be impersonated by the nobody account, so that account will need file-level permissions on that share directory. Samba will respect local permissions when figuring out who can write where, in this case it is somewhat like Windows."

  Read the article

• Smoothwall: How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• What needs updating when moving a bootable Windows 7 (or Vista) partition?

  - by SuperTempel

  When I move a bootable NTFS partition with Windows on it to a different block offset, what needs updating to make it bootable again? In particular, here's what I tried: I have a disk with several partitions, one of which is the NTFS partition with Windows on it, and the disk uses the plain old MBR block 0 for the partitions layout (no more than 4 partitions). Now I format and partition a new, larger, disk. There I make room for the NTFS partition and copy the contents from the old disk's NTFS Windows partition into. And I make the partition "active". However, when I try to boot from this disk, I get a "read error" message immediately and the booting stops, the exact text is: A disk read error occurred Press Ctrl+Alt+Del to restart I verified that both disks have the same boot sector code in block 0. It seems to me that something else might need updating. I guess that somewhere there's a absolute block reference that I need to update, probably pointing to the next level loader or to the NT kernel. Update: I found this article going quite into the depth of what I want to know. However, it says to modify boot.ini, but I have Windows 7 installed here, where such things appear to have changed: No boot.ini but a folder called System Volume Information with GUID and other data in it that sounds related to my problem. Going to keep digging... Update 2: Thanks to the terrible looking but very informative website by starman, I was able to figure out the first step: The NTFS boot sector has a field for "hidden" sectors. This feld has to contain the sector number of the boot sector. This solves the "read error" message. Now, however, I get a "BOOTMGR is missing" error instead. Looks like there's another place where a block number has to be adjusted, but I can't find anything in the code listing about this. I do find a lot of help sites suggesting Windows tools for fixing this "BOOTMGR is missing" problem, but none seem to know what goes on behind the scenes. Kind of like suggesting to re-install Windows when there's a little problem with it. At least, those fixes seem to work, mostly involving the Bcdedit and Bootrec tools. Now, who knows what they do, especially the latter, in regards to a moved partition? Update 3: After lots of trial-and-error attempts, I believe now that the solution lies in the BCD-Template registry file, residing usually inside \Windows\System32\config. If I get this updated using the "bcdboot" command, Windows starts up from it. I am now in the middle of figuring out what information this registry contains relevant to the above question. Any pointers to the contents of this registry are welcome. Update 4: Turns out that while the BCD-Template file gets rewritten and has different binary contents than its predecessor, the values inside do not change. So it must be something else that bcdboot.exe writes. I had previously already checked if it changes the first 32 boot blocks of the partition, but they appear to remain unchanged. Parititon map doesn't get changed, either. So what is it that bcdboot modifies besides the BCD registry? Any tips on how I can trace that? Are there low level tools that show me what files a program writes to? Update 5: The answer seems to be: c:\Boot\BCD is also changed, and that appears to be the key file for the boot manager's process. I'll investigate this later... Update 6: It seems to be an important detail that I had originally two partitions created when I installed Windows 7: A small partition of 204800 sectors which appears to be a bootstrap partition, followed by the actual, large, partition containing the Windows system (drive C:). When I tried to transfer this installation to a new, larger, disk, I had kept the same two partitions intact on the new drive, although they ended up at a different offset. This alone led to the "BOOTMGR is missing" message. Since then, I've used bcdboot.exe only on the Windows partition, which added the \Boot\BCD file on that partition. That file (and folder) did originally only exist on the smaller partition. Hence, this problem may be more complicated in my case as one partition (the boot strapper) referred to another partition (the one containing the OS), whereas other people may only have to deal with one partition containing both, and maybe there the solution is simpler. Update 7: Found one more detail: The \Boot\BCD file records the MBR's serial number. If that number doesn't match, the system won't boot. Next I'll test if there's also an absolute block reference stored in there.

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >