Search Results

Search found 35753 results on 1431 pages for 'app dev'.

Page 239/1431 | < Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >

  • How can I repair my USB drive?

    - by yurko
    USB drive is in read only state and I can't repair it. First of all I tried erase it using dd: root@yurko-laptop:/home/yurko-laptop# ls -l /dev/disk/by-id | grep usb lrwxrwxrwx 1 root root 9 ??? 18 23:45 usb-Generic_Flash_Disk_C173828A-0:0 -> ../../sdb lrwxrwxrwx 1 root root 10 ??? 18 23:45 usb-Generic_Flash_Disk_C173828A-0:0-part1 -> ../../sdb1 root@yurko-laptop:/home/yurko-laptop# dd if=/dev/zero of=/dev/sdb dd: ?????? ? «/dev/sdb»: ?? ?????????? ????????? ????? 8257537+0 ??????? ??????? 8257536+0 ??????? ???????? ??????????? 4227858432 ????? (4,2 GB), 942,633 c, 4,5 MB/c After that I wanted to create new filesystem using fdisk: root@yurko-laptop:/home/yurko-laptop# fdisk /dev/sdb You will not be able to write the partition table. WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): p Disk /dev/sdb: 4227 MB, 4227858432 bytes 4 heads, 63 sectors/track, 32768 cylinders Units = cylinders of 252 * 512 = 129024 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 18 32768 4126596 b W95 FAT32 Command (m for help): fdisk showed that the partition still exists and I can't write the partition table. I tried to delete the existing partition: Command (m for help): d Selected partition 1 Command (m for help): w Unable to write /dev/sdb root@yurko-laptop:/home/yurko-laptop# Why am I not be able to write the partition table? Does it mean that some hardware failure occurred? And is it possible to repair the current USB drive? I've tried to use hdparm and it showed that the readonly flag is on: root@yurko-laptop:/home/yurko-laptop# hdparm /dev/sdb /dev/sdb: SG_IO: bad/missing sense data, sb[]: f0 00 05 00 00 00 00 0a 00 00 00 00 26 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 multcount = 0 (off) readonly = 1 (on) readahead = 256 (on) geometry = 1016/131/62, sectors = 8257536, start = 0

    Read the article

  • BUILDROOT files during RPM generation

    - by khmarbaise
    Currently i have the following spec file to create a RPM. The spec file is generated by maven plugin to produce a RPM out of it. The question is: will i find files which are mentioned in the spec file after the rpm generation inside the BUILDROOT/SPECS/SOURCES/SRPMS structure? %define _unpackaged_files_terminate_build 0 Name: rpm-1 Version: 1.0 Release: 1 Summary: rpm-1 License: 2009 my org Distribution: My App Vendor: my org URL: www.my.org Group: Application/Collectors Packager: my org Provides: project Requires: /bin/sh Requires: jre >= 1.5 Requires: BASE_PACKAGE PreReq: dependency Obsoletes: project autoprov: yes autoreq: yes BuildRoot: /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/buildroot %description %install if [ -e $RPM_BUILD_ROOT ]; then mv /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/tmp-buildroot/* $RPM_BUILD_ROOT else mv /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/tmp-buildroot $RPM_BUILD_ROOT fi ln -s /usr/myusr/app $RPM_BUILD_ROOT/usr/myusr/app2 ln -s /tmp/myapp/somefile $RPM_BUILD_ROOT/tmp/myapp/somefile2 ln -s name.sh $RPM_BUILD_ROOT/usr/myusr/app/bin/oldname.sh %files %defattr(-,myuser,mygroup,-) %dir "/usr/myusr/app" "/usr/myusr/app2" "/tmp/myapp/somefile" "/tmp/myapp/somefile2" "/usr/myusr/app/lib" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/start.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/filter-version.txt" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/name.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/name-Linux.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/filter.txt" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/oldname.sh" %dir "/usr/myusr/app/conf" %config "/usr/myusr/app/conf/log4j.xml" "/usr/myusr/app/conf/log4j.xml.deliver" %prep echo "hello from prepare" %pre -p /bin/sh #!/bin/sh if [ -s "/etc/init.d/myapp" ] then /etc/init.d/myapp stop rm /etc/init.d/myapp fi %post #!/bin/sh #create soft link script to services directory ln -s /usr/myusr/app/bin/start.sh /etc/init.d/myapp chmod 555 /etc/init.d/myapp %preun #!/bin/sh #the argument being passed in indicates how many versions will exist #during an upgrade, this value will be 1, in which case we do not want to stop #the service since the new version will be running once this script is called #during an uninstall, the value will be 0, in which case we do want to stop #the service and remove the /etc/init.d script. if [ "$1" = "0" ] then if [ -s "/etc/init.d/myapp" ] then /etc/init.d/myapp stop rm /etc/init.d/myapp fi fi; %triggerin -- dependency, dependency1 echo "hello from install" %changelog * Tue May 23 2000 Vincent Danen <[email protected]> 0.27.2-2mdk -update BuildPreReq to include rep-gtk and rep-gtkgnome * Thu May 11 2000 Vincent Danen <[email protected]> 0.27.2-1mdk -0.27.2 * Thu May 11 2000 Vincent Danen <[email protected]> 0.27.1-2mdk -added BuildPreReq -change name from Sawmill to Sawfish The problem i found is that the files (filter.txt in particular) after the generation process on a Ubuntu system but not on SuSE system. Which might be caused by different rpm versions ? Currently we have an integration test which fails based on the non existing of the file (filter.txt under a buildroot folder?)

    Read the article

  • How to update Preview.app from the command line without losing focus on Mac OS X?

    - by snies
    I want to update Preview.app in the background from the command line without losing focus of my current window. I know that I can use the following to open/update the view of a file, but then I lose focus to the Preview.app. open -a Preview foo.pdf I guess there might be some clever AppleScript commands to do so but so far I didn't find the right one. Alternatively I would be interested into transfering the focus back to my current application directly after the update. I need this in order to update Preview.app's view of a PDF file through a vi autocmd after I update the PDF file according to changes in a TeX file I am editing. Here is an example of what I want to achieve but using Ubuntu and evince.

    Read the article

  • Should each app have its own database, or should small apps be merged into one?

    - by King
    We have a bunch of small to medium sized apps, each of which has its own database (MSSQL Server). There was a suggestion that we consoldate the 'related' databases into a smaller set amount of larger databases. They don't particularly share a lot of data, they would just be under a similar business group. For example, using a 'Finance' DB to hold the tables and procedures for finance apps. Would it be appropriate to use a different schema for each app? E.g. App1.SomeTable App1.SomeOtherTable AppTwo.SomeTable What are the pros and cons of this approach? What should I watch out for? Thanks

    Read the article

  • Forking a dual licensed app: How to license on my end?

    - by TheLQ
    I forked a project that was dual licensed under the GPL and a commercial license. Since my code was open source and the GPL being what it is, I started by releasing my app under the GPL. But now I'm thinking about dual licensing the project and can't figure out what to do. Since I have copyright on a majority of the code (most of the code was either rewritten or new), can I just pick a commercial license or do I have to buy the upstream commercial license since I'm technically a "derivative" of the project?

    Read the article

  • Virtualmin - Added Virtual Server - Stopped access to Rails app?

    - by Dan
    Hi, Sorry if this sounds pretty simple, I'm new to Virtualmin and running servers in general. I recently purchased a VPS and installed Virtualmin with no problems. I then installed mod_rails and uploaded my first rails app, which I got working by adding the following to my apache httpd.conf file: <VirtualHost *:80> ServerName testing.mydomain.com DocumentRoot /home/myapp/public <Directory /home/myapp/public> Allow from All AllowOverride all Options -MultiViews </Directory> RailsBaseURI / </VirtualHost> I then tried adding a virtual server through Virtualmin, using mydomain.com. Now, the site this created (plus several sub-servers) and working as expected. However, my original Rails app is no longer accessible. The URL now sends me to the parent application (ie mydomain.com) The Rails app is not located within the parent's application directory, would this be a problem? Can anyone help? Any advice appreciated. Thanks.

    Read the article

  • "'/usr/share/app-install/desktop/software-center.menu': Not a directory" error when trying to reinstall the software center

    - by EnTer
    I was having some problem with Software center. So tried to reinstall it. But While removing it give me an error. (Reading database ... 150986 files and directories currently installed.) Removing software-center ... dpkg: error processing software-center (--remove): unable to securely remove '/usr/share/app-install/desktop/software-center.menu': Not a directory Processing triggers for man-db ... Processing triggers for hicolor-icon-theme ... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Errors were encountered while processing: software-center E: Sub-process /usr/bin/dpkg returned an error code (1) Now The same problem is repeating if I use apt-get to install or upgrade my ubuntu. I cant install any software and Software-Center too.. PLZ help

    Read the article

  • May I use full-texted feed for my News Reader app?

    - by Mahdi Ghiasi
    I'm creating a news reader app. (Users will choose sources, but not the exact feed addresses. for example, they can choose Gizmodo but they will not see the exact url of Gizmodo's feed) Some of sources are giving partial feeds, and user must go to their website to read the complete article. My question is, May I make a fulltext version of their feed (for example, using this service) and use it instead of their feed in my News reader categories? Am I legally/ethically allowed to do this? What about using some other service like Readability? (Readability gives HTML page instead of feed as input, but anyway, output will be clean article without any advertises or such) Please note that some of these partial feeds may have some advertises inside, but the fulltext feed generators usually remove that advertises.

    Read the article

  • Open GL stars are not rendering

    - by Darestium
    I doing Nehe's Open GL Lesson 9. I'm using SFML for windowing, the strange thing is no stars are rendering. #include <SFML/System.hpp> #include <SFML/Window.hpp> #include <SFML/Graphics.hpp> #include <iostream> void processEvents(sf::Window *app); void processInput(sf::Window *app); void renderGlScene(sf::Window *app); void init(); int loadResources(); const int NUM_OF_STARS = 50; float triRot = 0.0f; float quadRot = 0.0f; bool twinkle = false; bool tKey = false; float zoom = 15.0f; float tilt = 90.0f; float spin = 0.0f; unsigned int loop; unsigned int texture_handle[1]; typedef struct { int r, g, b; float distance; float angle; } stars; stars star[NUM_OF_STARS]; int main() { sf::Window app(sf::VideoMode(800, 600, 32), "Nehe Lesson 9"); app.UseVerticalSync(false); init(); if (loadResources() == -1) { return EXIT_FAILURE; } while (app.IsOpened()) { processEvents(&app); processInput(&app); renderGlScene(&app); app.Display(); } return EXIT_SUCCESS; } int loadResources() { sf::Image img_data; // Load Texture if (!img_data.LoadFromFile("data/images/star.bmp")) { std::cout << "Could not load data/images/star.bmp"; return -1; } // Generate 1 texture glGenTextures(1, &texture_handle[0]); // Linear filtering glBindTexture(GL_TEXTURE_2D, texture_handle[0]); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_LINEAR); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_LINEAR); glTexImage2D(GL_TEXTURE_2D, 0, GL_RGBA, img_data.GetWidth(), img_data.GetHeight(), 0, GL_RGBA, GL_UNSIGNED_BYTE, img_data.GetPixelsPtr()); return 0; } void processInput(sf::Window *app) { const sf::Input& input = app->GetInput(); if (input.IsKeyDown(sf::Key::T) && !tKey) { tKey = true; twinkle = !twinkle; } if (!input.IsKeyDown(sf::Key::T)) { tKey = false; } if (input.IsKeyDown(sf::Key::Up)) { tilt -= 0.05f; } if (input.IsKeyDown(sf::Key::Down)) { tilt += 0.05f; } if (input.IsKeyDown(sf::Key::PageUp)) { zoom -= 0.02f; } if (input.IsKeyDown(sf::Key::Up)) { zoom += 0.02f; } } void init() { glClearDepth(1.f); glClearColor(0.f, 0.f, 0.f, 0.f); // Enable texturing glEnable(GL_TEXTURE_2D); //glDepthMask(GL_TRUE); // Setup a perpective projection glMatrixMode(GL_PROJECTION); glLoadIdentity(); gluPerspective(45.f, 1.f, 1.f, 500.f); glShadeModel(GL_SMOOTH); glBlendFunc(GL_SRC_ALPHA, GL_ONE); glEnable(GL_BLEND); for (loop = 0; loop < NUM_OF_STARS; loop++) { star[loop].distance = (float)loop / NUM_OF_STARS * 5.0f; // Calculate distance from the centre // Give stars random rgb value star[loop].r = rand() % 256; star[loop].g = rand() % 256; star[loop].b = rand() % 256; } } void processEvents(sf::Window *app) { sf::Event event; while (app->GetEvent(event)) { if (event.Type == sf::Event::Closed) { app->Close(); } if (event.Type == sf::Event::KeyPressed && event.Key.Code == sf::Key::Escape) { app->Close(); } } } void renderGlScene(sf::Window *app) { app->SetActive(); // Clear color depth buffer glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); // Apply some transformations glMatrixMode(GL_MODELVIEW); glLoadIdentity(); // Select texture glBindTexture(GL_TEXTURE_2D, texture_handle[0]); for (loop = 0; loop < NUM_OF_STARS; loop++) { glLoadIdentity(); // Reset The View Before We Draw Each Star glTranslatef(0.0f, 0.0f, zoom); // Zoom Into The Screen (Using The Value In 'zoom') glRotatef(tilt, 1.0f, 0.0f, 0.0f); // Tilt The View (Using The Value In 'tilt') glRotatef(star[loop].angle, 0.0f, 1.0f, 0.0f); // Rotate To The Current Stars Angle glTranslatef(star[loop].distance, 0.0f, 0.0f); // Move Forward On The X Plane glRotatef(-star[loop].angle,0.0f,1.0f,0.0f); // Cancel The Current Stars Angle glRotatef(-tilt,1.0f,0.0f,0.0f); // Cancel The Screen Tilt if (twinkle) { glColor4ub(star[(NUM_OF_STARS - loop) - 1].r, star[(NUM_OF_STARS - loop)-1].g, star[(NUM_OF_STARS - loop) - 1].b, 255); glBegin(GL_QUADS); // Begin Drawing The Textured Quad glTexCoord2f(0.0f, 0.0f); glVertex3f(-1.0f, -1.0f, 0.0f); glTexCoord2f(1.0f, 0.0f); glVertex3f( 1.0f, -1.0f, 0.0f); glTexCoord2f(1.0f, 1.0f); glVertex3f( 1.0f, 1.0f, 0.0f); glTexCoord2f(0.0f, 1.0f); glVertex3f(-1.0f, 1.0f, 0.0f); glEnd(); // Done Drawing The Textured Quad } glRotatef(spin,0.0f,0.0f,1.0f); // Rotate The Star On The Z Axis // Assign A Color Using Bytes glColor4ub(star[loop].r, star[loop].g, star[loop].b, 255); glBegin(GL_QUADS); // Begin Drawing The Textured Quad glTexCoord2f(0.0f, 0.0f); glVertex3f(-1.0f,-1.0f, 0.0f); glTexCoord2f(1.0f, 0.0f); glVertex3f( 1.0f,-1.0f, 0.0f); glTexCoord2f(1.0f, 1.0f); glVertex3f( 1.0f, 1.0f, 0.0f); glTexCoord2f(0.0f, 1.0f); glVertex3f(-1.0f, 1.0f, 0.0f); glEnd(); // Done Drawing The Textured Quad spin += 0.01f; // Used To Spin The Stars star[loop].angle += (float)loop / NUM_OF_STARS; // Changes The Angle Of A Star star[loop].distance -= 0.01f; // Changes The Distance Of A Star if (star[loop].distance < 0.0f) { star[loop].distance += 5.0f; // Move The Star 5 Units From The Center star[loop].r = rand() % 256; // Give It A New Red Value star[loop].g = rand() % 256; // Give It A New Green Value star[loop].b = rand() % 256; // Give It A New Blue Value } } } I've looked over the code atleast 10 times now and I can't figure out the problem. Any help would be much appreciated.

    Read the article

  • Should I use the same Google Analytics code for my website and native mobile app?

    - by Drew
    My website is a forum. The native mobile app's only function is to access the forum and provide a better experience than can be provided through the browser. Given that the same content is being accessed, should I use the same Google Analytics tracking code? Or should I create a new property and select "Not a website" when it asks for the website? I was not able to find anything that discussed this and what would be best practice, given that the same content is being accessed. Thanks!

    Read the article

  • Ubuntu 11.10 doesn't detect external usb hard drive

    - by Andrew
    I have been batting with this issue for a bit and cannot find the answer to it. So the Dmesg see's the device, being Symwave WDC WD64.... media@Media-pc:~$ dmesg | tail -n 20 [78678.719497] scsi 10:0:0:0: Direct-Access Generic- USB3.0 CRW -0 1.00 PQ: 0 ANSI: 0 CCS [78678.725621] scsi 10:0:0:1: Direct-Access Generic- USB3.0 CRW -1 1.00 PQ: 0 ANSI: 0 CCS [78684.073837] scsi 11:0:0:0: Direct-Access SYMWAVE WDC WD6400AAKS-0 3B01 PQ: 0 ANSI: 4 [78691.008126] scsi 11:0:0:0: uas_eh_abort_handler tag 0 [78691.008139] scsi 11:0:0:0: uas_eh_device_reset_handler tag 0 [78691.008147] scsi 11:0:0:0: uas_eh_target_reset_handler tag 0 [78691.008154] scsi 11:0:0:0: uas_eh_bus_reset_handler tag 0 [78691.080307] usb 2-2.4: reset high speed USB device number 9 using ehci_hcd [78691.221427] scsi 11:0:0:0: Device offlined - not ready after error recovery [78691.221498] scsi 11:0:0:0: rejecting I/O to offline device [78691.221519] scsi 11:0:0:0: rejecting I/O to offline device [78691.222952] scsi 11:0:0:1: Enclosure SYMWAVE SES 3B01 PQ: 0 ANSI: 4 [78691.223156] scsi 11:0:0:2: uas_sense_old: urb length 26 disagrees with IU sense data length 510, using 18 bytes of sense data [78691.225061] sd 11:0:0:0: Attached scsi generic sg3 type 0 [78691.225344] ses 11:0:0:1: Attached Enclosure device [78691.225495] ses 11:0:0:1: Attached scsi generic sg4 type 13 [78691.226266] sd 10:0:0:0: Attached scsi generic sg5 type 0 [78691.226653] sd 10:0:0:1: Attached scsi generic sg6 type 0 [78691.241647] sd 10:0:0:0: [sdd] Attached SCSI removable disk [78691.243832] sd 10:0:0:1: [sde] Attached SCSI removable disk It looks like it attaches sdd and sde. Now when i look in the disk utility it shows "Hard disk Symwave WD6400AAKS-0 device /dev/sdc doesn't show any other info then that, if i format, it says that it cannot open /dev/sdc no device or address error. Underneeth the device it does show two general usb3.0 CRW that are sdd and sde. Now if I do a fdisk -l it doesn't show the device: media@Media-pc:~$ sudo fdisk -l Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000247de Device Boot Start End Blocks Id System /dev/sda1 * 2048 152176639 76087296 83 Linux /dev/sda2 152178686 156301311 2061313 5 Extended /dev/sda5 152178688 156301311 2061312 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x948fc822 Device Boot Start End Blocks Id System /dev/sdb1 63 1953520064 976760001 7 HPFS/NTFS/exFAT So now I am confused. Any ideas how I get fdisk to see the device?

    Read the article

  • Can't see Windows partition in Nautilus

    - by Anders Feder
    I am on Ubuntu 11.10. I used to be able to access my Windows partion from the list of devices in Nautilus, but I no longer see it. What might be wrong? Running sudo blkid gives the following: /dev/loop0: UUID="ef34b449-1330-4ac5-bb69-e1475c0b91da" TYPE="ext4" /dev/sda1: LABEL="PQSERVICE" UUID="D04C76D04C76B138" TYPE="ntfs" /dev/sda2: LABEL="SYSTEM RESERVED" UUID="EC4878594878248C" TYPE="ntfs" /dev/sda3: LABEL="Acer" UUID="54947A5A947A3E94" TYPE="ntfs" Thanks.

    Read the article

  • Kubuntu 12.04 - Touchpad and keyboard stopped working at random

    - by StepTNT
    As in the title, I've got this problem with my Kubuntu 12.04. At first I've thought that the whole system was hung, but it happened again 5 minutes ago and, while the keyboard and the touchpad stopped working, the music was still playing, so I guess that's just an "input" problem, because the system was still working! Any solution? Is there some data that you need to know about my setup? EDIT: Added my lshw outout description: Notebook product: N53SV () vendor: ASUSTeK Computer Inc. version: 1.0 serial: B2N0AS17695408A width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=N uuid=8083F2DA-A43E-E081-3F3F-BCAEC55F8AA1 *-core description: Motherboard product: N53SV vendor: ASUSTeK Computer Inc. physical id: 0 version: 1.0 serial: BSN12345678901234567 slot: MIDDLE *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: N53SV.214 date: 08/10/2011 size: 64KiB capacity: 2496KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb smartbattery biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 800MHz capacity: 4GHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer xsave avx lahf_lm ida arat epb xsaveopt pln pts tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache description: L1 cache physical id: 5 slot: L1-Cache size: 32KiB capacity: 32KiB capabilities: internal write-back instruction *-memory description: System Memory physical id: 40 slot: System board or motherboard size: 10GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: 99U5428-040.A00LF vendor: Kingston physical id: 0 serial: 103C28C3 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 58383D1F slot: ChannelA-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 2 serial: 58183D19 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 3 serial: 58183C8F slot: ChannelB-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:d000(size=4096) memory:db000000-dc0fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:db000000-dbffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:d000(size=128) memory:dc000000-dc07ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:dc400000-dc7fffff memory:b0000000-bfffffff ioport:e000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:48 memory:df00b000-df00b00f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:df008000-df0083ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:49 memory:df000000-df003fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:c000(size=4096) memory:de600000-deffffff ioport:d4200000(size=10485760) *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:b000(size=4096) memory:ddc00000-de5fffff ioport:d3700000(size=10485760) *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 48:5d:60:f2:2c:fd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-24-generic firmware=N/A ip=192.168.1.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:ddc00000-ddc0ffff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:a000(size=4096) memory:dd200000-ddbfffff ioport:d2c00000(size=10485760) *-usb description: USB controller product: FL1000G USB 3.0 Host Controller vendor: Fresco Logic physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:dd200000-dd20ffff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:44 ioport:9000(size=4096) memory:dc800000-dd1fffff ioport:d2100000(size=10485760) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: bc:ae:c5:5f:8a:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168e-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:46 ioport:9000(size=256) memory:d2104000-d2104fff memory:d2100000-d2103fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:df007000-df0073ff *-isa description: ISA bridge product: HM65 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:e0b0(size=8) ioport:e0a0(size=4) ioport:e090(size=8) ioport:e080(size=4) ioport:e060(size=32) memory:df006000-df0067ff *-disk description: ATA Disk product: ST9750420AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 0002 serial: 5WS0A7QR size: 698GiB (750GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=e0c5913d *-volume:0 description: Windows FAT volume vendor: MSDOS5.0 physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: FAT32 serial: 4ce5-3acb size: 3004MiB capacity: 3004MiB capabilities: primary fat initialized configuration: FATs=2 filesystem=fat *-volume:1 description: EXT4 volume vendor: Linux physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 logical name: / version: 1.0 serial: c198cc2a-d86a-4460-a4d5-3fc0b21e439c size: 28GiB capacity: 28GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-03-15 16:53:54 filesystem=ext4 lastmountpoint=/ modified=2012-05-02 18:52:04 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,acl,barrier=1,data=ordered mounted=2012-05-09 19:06:01 state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 4c1cdebc-ec09-2947-a3b5-c1f9f1cddc1c size: 152GiB capacity: 152GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-02-22 16:02:47 filesystem=ntfs label=OS state=clean *-volume:3 description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 size: 514GiB capacity: 514GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 10GiB capabilities: nofs *-logicalvolume:1 description: HPFS/NTFS partition physical id: 6 logical name: /dev/sda6 capacity: 504GiB *-cdrom description: DVD-RAM writer product: BD-MLT UJ240AS vendor: MATSHITA physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 1.00 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:df005000-df0050ff ioport:e040(size=32)

    Read the article

  • Ubuntu 12.04 does not recognise CD

    - by Venkat Kotra
    ~$ wodim --devices wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg1' rwrw-- : 'MATSHITA' 'DVD-RAM UJ8B1AS' ------------------------------------------------------------------------- But I don't find access to CD. Kindly let me know how to rip the CD. When I try to mount, it gives error. ~$ mount /dev/sg1 can't find /dev/sg1 in /etc/fstab or /etc/mtab

    Read the article

  • formatting before md device creation in RAID5

    - by kumar
    consider you are creating a raid5 device with three drives. mdadm --create /dev/md0 --leve=5 --raid-disk=3 /dev/sda1 /dev/sdb1 /dev/sdc1 After issuing this command , I can see the progress of md device creating using cat /proc/mdstat. During the progress ITSELF, can I create a file ssytem partition say ext2 on md0 device like: mkfs.ext2 /dev/md0. Actually I am able to create this and want to confirm whether doing this before 100% completion of md device creation is CORRECT?

    Read the article

  • Is there a network "tee"-alike with one leg returning to /dev/null ?

    - by Steff Davies
    I've just built a new PostgreSQL server for my employers, which is happily replicating using WALs. I'm now left with the problem of verifying its performance. One nice way which came up in conversation is to break replication with the slave caught up and then direct all production traffic to both servers, discarding the responses from the new server and returning those from the current one to the clients. Once we're sure performance is OK, we re-sync the slave and can fail over with confidence. Bliss. This would require a TCP proxy capable of opening two outgoing connections for each incoming one, and discarding the data returned from one of them, which is a tricky thing to google for, it seems. Do the assembled brains know of such a thing, before I dive into libevent and write one?

    Read the article

  • Is there an app/script I can deploy to enable my users to change their own LDAP passwords?

    - by Tom Wright
    I've recently enabled LDAP based authentication on my domain. This has allowed us to use a single set of credentials to administer the blog, the forum and the wiki. Unfortunately, this has come at the cost of users being able to change their own passwords. Ideally, users would be able to visit a page (i.e. mydomain.com/account), authenticate and then change their password. Does anyone know of a script or app that will allow me to do this quickly and easily? I guess it wouldn't be hard to write in PHP, but I'd prefer not to have the hassle.

    Read the article

  • I'm porting my app from iOS to Android: what do I need to know?

    - by kubi
    What pitfalls should I avoid? What Java language paradigms do Objective-C developers consistently misunderstand? I learned to program in Java, but I have worked in nothing but Objective-C for years now. How are the design patterns different between Android and iOS? If you've made the transition yourself, what parts of Android confused you or took you longer to learn than it should have? Is Eclipse the best OS X IDE for Android? For the record, my app is very strongly tied to UIKit and Foundation, so the word "porting" may be a misnomer; I'll actually be completely rewriting it for Android. No code reuse. Also, I'm doing this to learn Android, so I'd rather fail at the port and learn Android than take a shortcut.

    Read the article

  • RIM's current BB7 developer toolset is a joke

    - by mbrit
    tl;dr - RIM's current developer toolset is not fit for purpose.Background to this is that I'm currently working on a PhoneGap/Cordova project for a client that has to run on BlackBerry. The tooling is so ridiculous to use that even though I had a gentle dig at them in a Guardian piece it's worth having a more full-on attack.At the moment, RIM's pitch is that apps are built for the current BBOS7 devices using WebWorks. This is an HTML-based toolset. Essentially a browser is spun up in a native app container and your app is powered by JavaScript. Specific JavaScript libraries exist that thunk down to native capabilities no the device. I happen to use PhoneCap/Cordova in combination with this.The tooling is non-existent. I'm using TextMate, Ant, and Terminal to develop the app. There's no "console.log" output, and no debugging. The only way to instrument the app is to put "alert" calls in your code.Apart from the fact that that's *not* fine in 2012, how about this… every time you deploy a new app to the device, the device has to reboot. This process takes six minutes on a relatively modern BlackBerry device. How about this as well - in order to get a file into the package it has to be signed. My small app over here has 100 different files (75 or so generated). Signing doesn't happen locally, it happens on RIM's servers in Waterloo. Thus whenever you deploy the app you have this utility have to call RIM's servers 100 times. More to the point, sometimes during the day these servers have "micro-downtime" moments where they're unreachable for five or ten minutes, normally two or three times a day. Oh yes, you'll also get an email sent to you per signing on success or failure. 100 inbound emails, per deployment.(I started this post at the beginning of one of these cycles, by the way. That's how long it takes to build and deploy *once*. By the way, the change I made didn't work.)To clarify:* Change the script,* Build it using Ant,* Ant will spin up a Java app that talks to RIM's servers to sign it.* Receive 100 emails, assuming the server is up.* App deployed - takes about 30 seconds.* BlackBerry device restarts - takes about six minutes.* Find and open the app. Go through security prompts.* Test the app, with no "console.log" output and no debugger."Why not use the simulator?" I hear you ask. Well, apart from the fact that the simulator refused to reach any network service over HTTPS that I happen to own? (Some people suggest changing DNS settings for this known issue.) Admittedly, the simulator does show you console.log, but you still have the "six minute" restart issue on the simulator.Developers will understand this problem. Breaking concentration for six-plus minutes every time you want to deploy an app turns developing into a nightmare. Combining that with no worthy debugging tools turns the toolset into a joke.

    Read the article

  • BlueStacks Joins Forces with AMD; Launches AMD-only Enhanced Android App Launcher

    - by Jason Fitzpatrick
    Last fall we showed you how to run Android apps on your Windows PC with BlueStacks. Now BlueStacks has partnered with AMD to offer even better Android emulation on AMD-powered Windows machines. Check out our original overview and installation guide for BlueStacks to get a feel for what you can do with the app. If you’re sporting an AMD CPU, hit up the link below to check out the AMD AppZone to grab some of the thousands of Android apps you can enjoy on your desktop. AMD AppZone: Android [via Gigaom] 8 Deadly Commands You Should Never Run on Linux 14 Special Google Searches That Show Instant Answers How To Create a Customized Windows 7 Installation Disc With Integrated Updates

    Read the article

  • installation ubunto 14.01 on a different partition with windows 8.1

    - by bilel abidi
    Please assist me. I am eager to install Ubunto 14.01 on a different partition but I do not know how to do it. I have HP with windows 7 pre-installed then I upgraded to windows 8.1 please show me how to make a dedicated partition to install ubuntu 14.01. please find the partition that I have. I appreciate your help on a I have : partition : /dev/sda1 NTFS label system 922.50KB /dev/ sda2 NTFS 199.00MIB flags : boot /dev/sda3 NTFS label receovery 488.77 GB /dev/sda4 unknown 16 GB unallocated 1 MIB

    Read the article

  • How to get an inactive RAID device working again?

    - by Jonik
    After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make the device active again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question. Edit: My /etc/mdadm/mdadm.conf looks like this. I've never touched this file, at least by hand. # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR <my mail address> # definitions of existing MD arrays # This file was auto-generated on Wed, 27 Jan 2010 17:14:36 +0200 In /proc/partitions the last entry is md_d0 at least now, after reboot, when the device happens to be active again. (I'm not sure if it would be the same when it's inactive.) Resolution: as Jimmy Hedman suggested, I took the output of mdadm --examine --scan: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=de8fbd92[...] and added it in /etc/mdadm/mdadm.conf, which seems to have fixed the main problem. After changing /etc/fstab to use /dev/md0 again (instead of /dev/md_d0), the RAID device also gets automatically mounted!

    Read the article

  • How to route traffic through a specific SOCKS proxy on a per-app basis?

    - by GJ.
    I'm running a certain desktop app (actually via AIR if it makes any difference) which doesn't have any built-in proxy configuration settings. I need to get all traffic just from this app directed through a secure SOCKS proxy. This implies I can't use the global network preferences, as these would affect many other apps. Is there any way to force all network communication through a given SOCKS proxy on a per-app basis? It would also be helpful to know if there's a way to perform such routing globally, based on specific IP addresses (as this could allow for some reasonable workaround).

    Read the article

  • UI Design Patterns : Are you developing a Fusion Apps extension, an ADF or Webcenter App?

    - by asantaga
    A big question I get asked when speaking to partners who are developing Oracle ADF, or Webcenter, Apps is how to make it look nice.. Some of the big SIs ask me, "Do we have any design patterns/guidelines we can use?". .. Alas website design is a very personal thing and each website will have different requirements and needs, however I am now pleased to say we've just launched "Oracle Fusion Applications Design Patterns" website.   The website is the result of many years of Oracle R&D into user interface design for Fusion applications and features a really cool web app which allows you to visualise the UI components in action. Although many of the design patterns are related to ADF , its worth noting that ADF took its lead from Oracle Fusion Applications User Interface needs - not the other way around, its just taken us a while to publish these. Coupled together with the dashboard patterns this makes are really cool extra asset for your kit bag Design Patterns Oracle dashboard patterns and guidelines Usable Apps.oracle.com Enjoy

    Read the article

  • it is a good approach to implement dependency injection in a desktop app?

    - by luis_laurent
    Well, the thing is that I am just about to create a Desktop App (with .NET windows forms) And now I just wonder if it would be really a wise choise to use any IoC (StructureMap,Ninject,Spring .Net), I have used them before for Asp.Net web applications but what makes me doubt now is the fact that working with windows forms my business entities will persist when I navigate through tabs and unlike than web forms or mvc apps where it would be necesary to inject my business entity for every new request that is performed, I mean this because of the Asp.Net page life cycle where is performed the initialization and controls instantiation. Maybe I am misunderstanding the point of using an IoC, so please tell me what do you think would be a better choise?

    Read the article

< Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >