Search Results

Search found 19676 results on 788 pages for 'hardware interface'.

Page 241/788 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Monitoring ASA packet loss via SNMP

  - by dunxd

  I want to monitor packet loss on my ASA 5505 VPN endpoints using SNMP. This is so I can graph the rates in Cacti and/or get alerts in Nagios. However, I am not sure what SNMP values I should use to measure packet loss. In the ASA I can run sh interface Internet stats to show traffic statistics for the interface connected to the Internet. This shows 1 minute and 5 minute drop rates. Are these measures an indicator of packet loss? Are there SNMP values I can access that correspond to those values? Should I be looking at different values? Is the ASA even able to measure packet loss?

  Read the article

• Using local proxy to specify used NIC on Windows 7?

  - by Nico

  I'm running Windows 7 and have 2 NIC installed, both are connected to the Internet (nic#1 LTE, nic#2 DSL). Windows 7 will only allow me to specify a binding order and a metric on which interface to chose but i can't specify this on an application level. My Idea was to use a local proxy server and use the proxy server whenever i want to use nic#2. I tried wingate and free proxy, both applications will let me chose the interface i want to use but this setting seems to have no effect? This is how i configured the applications: http://imageshack.us/photo/my-images/69/freeproxysettings.jpg/ http://imageshack.us/photo/my-images/811/wingateproxysettings.jpg/ Is what i'm trying to do in anyway possible?

  Read the article

• Why do I have to manually 'Restart Management Network' on vSphere 5 host after reboot to get networking available?

  - by growse

  I've got a couple of vSphere 5.0 hosts in a small lab environment here and I've noticed a strange behaviour. When on of the hosts gets rebooted, it is unresponsive to the network until I log into the ESX console, Press F2 to customize and select Restart management network. Once this is done, the networking works perfectly as expected. Each host has two NICs which are trunked together using Etherchannel to a Cisco 3750. The link is also a .1q VLAN trunk and the management network is configured on VLAN121 with the VM traffic configured on VLAN118. Why would the host be completely dead to the world until I physically kick it? Edit Sample switch config for trunk: interface Port-channel2 description Blade 1 EtherChannel Trunk switchport trunk encapsulation dot1q switchport mode trunk end ! ! interface GigabitEthernet4/0/1 description Bladecenter1 CPM 1A switchport trunk encapsulation dot1q switchport mode trunk speed 1000 duplex full channel-group 2 mode on end Vswitch teaming settings: Management port group settings:

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• Anti Aliasing dead

  - by Gazoza

  I have a problem with anti-aliasing. No matter the software settings, it seems to be gone. I tried driver updating and reinstalling, cleaning of the hardware, different monitor with different cablies, OS reinstalling and changing, none of which helped. I decided to change the graphic card, but that didn't work either. Moreover, I have a distinct impression that the jagged edges are worsening as time goes by. I think this is a hardware-related issue, but I don't know exactly what to do. If anyone here had similar troubles, and/or has an idea how to cope with them, I'd be very grateful. My current card is a nVidia GT610.

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• smallest footprint for Web Application server?

  - by edgardodelamanta

  There are times when you need to spare hardware resources (either to keep using legacy hardware, to play the embedded card, or just to be efficient because a large footprint is trashing CPU caches, leading to unacceptable levels of idle-states). In this spirit, some efforts have been made to make 'light' ports of Java or Mono (C# for Linux), and they range in the 80-50 MB (instead of the 100-200 MB). Add a Web server (Apache, IIS, etc.) to the scripting engine and you can happily dive into the GB (IIS + .Net) only to load the tool in memory. Anybody with more modest tools in the specs area?

  Read the article

• How long will the serial port be around for?

  - by Andy

  It seems that the serial port has a remarkable ability to stick around. You might call it the hardware equivalent of Windows XP. Despite pretty much physically disappearing from laptops and the like, the need to use a serial port still exists, even if it means using a converter of some sort. It is very much a legacy piece of hardware, and yet so many devices and instruments still use it. I use it myself daily in my work with PLC's, HMI's, barcode readers, etc. In my opinion, I don't think it is going anywhere soon, but how long do you think it has got before joining the museum? Do you think it ever will?

  Read the article

• Trixbox CentOS Default GW Problem (Multi-homed server)

  - by slashp

  I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

  Read the article

• Cisco 877 as PPPoA/PPPoE bridge (no routing) - how to make it listen to IP for management?

  - by Ingmar Hupp

  I have a Cisco 877 configured to bridge ADSL with PPPoA to PPPoE on Vlan1. This works fine, but in this mode the only way I can configure the Cisco is via the serial console. I'd like to have the Cisco also listen on an IP address so I can telnet/ssh into it. I think the right way to go about this would be via bridge irb, but I'm not sure exactly how (or if that's even the right direction). IOS is 12.4T and my current config (cut down to essentials) is: no ip routing no ip cef ! ! interface ATM0 no ip address no ip route-cache no atm ilmi-keepalive pvc 0/38 encapsulation aal5snap ! dsl operating-mode auto bridge-group 1 ! ! interface Vlan1 no ip address no ip route-cache bridge-group 1 Just setting an IP address on Vlan1 didn't have the desired effect, but surely this must be possible somehow (the Draytek Vigor 120 even does it by default).

  Read the article

• Where is debian storing its network settings?

  - by user13743

  I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

  Read the article

• IDE to SATA convertor Motherboard Issue

  - by ravidev

  I bought new motherboard Intel DH67GD which has not IDE interface to attach the DVD writer. It has 2 SATA with 6Gb/s, 3 SATA with 3Gb/s and 1 e-SATA with 3GB/s.(mobo specs link : http://www.intel.in/content/www/us/en/motherboards/desktop-motherboards/desktop-board-dh67gd.html) Can anyone tell me how can i connect my old LG DVD Writer(IDE interface) with Mobo ?? Will IDE to SATA Connector work? If yes then how to connect that DVD writer with IDE-SATA converter? Please provide link. Thanks in advance !!

  Read the article

• Citrix XenApp application does not have keyboard focus when launched

  - by Jason Pearce

  On new or existing Citrix XenApp 4.5 servers, I am having problems streaming the Allscripts Pro EHR application via the XenApp web interface. When users launch the application via the Citrix XenApp web interface, the application does not have focus, preventing users from typing in their username and password. If they use their mouse to select either the username or password fields, they still cannot enter any text. However, if they do any of the following actions, they can then enter in their username and password and the application runs without problems: Click on the Login button with empty fields. Logon fails but they can then enter their credentials. Minimize the login window and then maximize it. They can then gain keyboard focus to enter their credentials. What might be preventing this particular application from having focus when it launches?

  Read the article

• Application to use for Winfast DTV1000T Tuner card

  - by lagerdalek

  The WinFast application that they have built for the purpose is pretty typical of hardware vendor built software, and was looking for something nicer.

  Read the article

• How to correctly set up iWARP? Preferably on loopback

  - by ajdecon

  iWARP is a protocol for doing remote direct memory access (RDMA) on top of TCP/IP, so that it can work with Ethernet and other network types as opposed to Infiniband. It works with many of the standard IB interfaces - the IB verbs, for example - so it's all pretty transparent. I'm doing some IB-verbs programming (mostly for the sake of learning about how they work better), and it'd be wonderfully convenient for me if I could use iWARP to do RDMA over my loopback interface, so that I could test some of my code without getting on our IB-connected cluster. :-) But I cannot figure out how to get a "local development environment" set up: there are no tutorials I'm aware of for even setting up iWARP from scratch on a server or a network interface. Can anyone give me a tutorial or point me in the right direction? Environment is Fedora 16 running in VirtualBox.

  Read the article

• Windows Phone 8 not interfacing with Zune software

  - by Cyberherbalist

  I just got a Lumia 521 with Windows Phone 8 and am trying to get the device to work with the Zune software on my PC. I still have my Windows Phone 7 device, and the new one is not working the same way. When I plug the WP7 device into the PC's USB port, it automatically fires up Zune and I can sync my podcasts and music etc to the device. But when I plug the Lumia into the PC it doesn't fire up Zune, and if I start Zune manually, it doesn't interface with the phone at all. Perhaps I am missing something and WP8 isn't supposed to use Zune to interface with the phone?

  Read the article

• Chain Gateways on the LAN

  - by Black2night

  I installed m0n0wall in a virtualized environment, i have 10 PCs connected to a router ( 192.168.1.0/24) which connect them to the internet through PPPoE, the problem is that this router does not have a QoS so what i want to do is the following :- let all the PCs get their IP from the Router and the default gateway will be m0n0wall the moon wall will have 2 interface (Lan 192.168.1.20) and (Wan 192.168.1.21 and default gateway 192.168.1.1) now when any PC want to access the internet it should go through m0n0wall and then m0n0wall will forward the connection to the default gateway through the wan interface which is the PPPoE running on the router (192.168.1.1) the big question is this scenario possible or not and what do you suggest? Thanks

  Read the article

• Windows 7, Drivers, Cloning and Sysprep

  - by Frank Thornton

  I have Windows 7 working on one machine but when I move it off to the new machine it crashes. If this is a driver issue do I need to download the drivers and install them first? Or do I install Windows 7 on the new machine first then copy the drivers folder over to the other disk so it will boot up correctly? EDIT: I was trying this as well: http://www.todo-backup.com/support/tutorial/redeploy-system-to-dissimilar-hardware.htm EDIT: I tried sysprep but on bootup I see the Windows logo then the system crashes. I can stick the drive back in the old hardware and it runs fine.

  Read the article

• Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

  - by lanbo

  A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

  Read the article

• sonicwall nsa 240

  - by Adam

  Hi We are looking into putting a hardware firewall into a data center to protect our rack of servers. We are using the servers for terminal services and we have 2 x 1GB connections to the Internet. We have about 50 servers supporting about 250 users which will grow very soon to 500 users. We plan to purchase 2 hardware firewalls to provide HA. Do you think the Sonicwall NSA 240 with Total Secure is a good match for this in terms of performance and protection (from spyware, virus etc?) or is there a better purchase? (Maybe a Watchguard X5 or X8?)

  Read the article

• AMD Processors and the Windows Phone 8 Emulator

  - by Aj Patel

  I would madly appreciate it if anyone in this community would help me with my question. The background is that I want to develop Windows Phone 8 applications but both of my current computer processors do not have Hardware Virtualization & Second Level Address Translation that are needed to run the Emulator. I have my eyes on an AMD computer g7-2243us (I like it because it has 1600x900 screen res). I looked up this Link that shows that this computer's AMD processor (Next Gen AMD Quad-Core A8-4500M Accelerated 1.9GHz up to 2.8GHz 4MB L2 Cache Processor) supports AMD-V Hardware Virtualization. So, will this computer be able to run the emulator? Thank you so much for your answers. I'm pretty sure it will run the emulator, but I just want to make sure before spending $400. Thank You all So Much.

  Read the article

• From a quality perspective, what is better: Turning volume up in the software, in the OS, or on the speakers?

  - by Qqwy

  I kept thinking about this, and out of sheer curiosity, I decided to ask: If music isn't loud enough. How do I get the best quality?(Even if the difference is in fact so small it's neglectible) By making the music louder in my music player, game or other sound-producing software program. By raising the volume at the Operating System level (for instance, by clicking the 'speaker' icon on the windows bar and turning the volume up) By turning the volume up on the Amplifier or Speakers that are attached to your computer, and thus changing the volume on the 'hardware' Does programs vs OS matter? Does software vs. hardware matter? Thanks, Qqwy

  Read the article

• How to get rid of NAT in a LAN?

  - by Alberto

  Currently the LAN I manage is organized as follows: internal network (192.168.1.0) which uses a Linux server as a gateway (internal address on interface br0 192.168.1.1, external address on interface br1 10.0.0.2) through NAT; then the 10.0.0.0 network has another gateway (10.0.0.1) which through another NAT connects the whole thing to the internet. What I would like to achieve is to configure the Linux server so that the first layer of NAT is no more necessary, so that for example a computer in the 10.0.0.0 network can ping every computer in the 192.168.1.0 network. I deleted this iptables rule: iptables -t nat -A POSTROUTING -o br1 -j SNAT --to-source 10.0.0.2, but of course now computers on 192.168.1.0 cannot reach the internet; ip forwarding is of course enabled. What's missing here? Thanks

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >