Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 241/783 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Windows 7 laptop with two active network connections will not perform DNS AAAA lookup under certain conditions

  - by Jeff Loughridge

  My laptop has two network interfaces. The Ethernet interface connects directly to my provider's edge router. It obtains an IPv6 address via SLAAC. I manually set an IPv6 DNS server. The wireless interface connects to a CPE router that doesn't understand IPv6. If the wireless interface is disabled, I can reach the IPv6 Internet with no problems using the Ethernet interface. I run into problems when both interfaces are enabled and the wireless interface get its IPv4 DNS server via DHCP. Let's look at two scenarios. Wireless interface obtains IPv4 DNS server via DHCP - The CPE router (192.168.0.1) sends its address as the DNS server. In this scenario, Windows 7 will not perform AAAA lookups. The browser uses IPv4 transit to reach dual stack web sites. I can't reach IPv6-only web sites using domain names. I can reach IPv6-enabled web sites using IPv6 literals instead of the domain name. Wireless interface is manually configured with OpenDNS DNS server - Windows 7 performs AAAA lookups using IPv6 transit (via the Ethernet). Everything works fine. My dual homed set-up is definitely not standard. Still, the behavior is very strange to me. A valid IPv6 interface exists in my Ethernet interface. Why won't Windows attempt AAAA lookups in scenario #1? I've included the output of ipconfig /all and netstat -rn. C:\Program Files\Console>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : jake Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : res.openband.net Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : DW1520 Wireless-N WLAN Half-Mini Card Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::fc39:9293:7d01:4a75%13(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.105(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Wednesday, July 11, 2012 7:35:21 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 9:49:46 AM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 364956472 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : 208.67.222.222 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connection Physical Address. . . . . . . . . : 5C-26-0A-03-23-5C DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2607:2600:1:850:c0e9:211a:fd05:4e0b(Preferred) Temporary IPv6 Address. . . . . . : 2607:2600:1:850:3d29:1839:62db:c4c1(Preferred) Link-local IPv6 Address . . . . . : fe80::c0e9:211a:fd05:4e0b%12(Preferred) IPv4 Address. . . . . . . . . . . : 10.52.2.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.254.0 Lease Obtained. . . . . . . . . . : Monday, July 09, 2012 8:55:07 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 7:30:05 AM Default Gateway . . . . . . . . . : fe80::214:6aff:fe51:7f3f%12 10.52.2.1 DHCP Server . . . . . . . . . . . : 216.40.77.244 DNS Servers . . . . . . . . . . . : 2620:0:ccc::2 2620:0:ccd::2 216.40.77.126 216.40.77.244 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::4c61:495b:229e:281e%14(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.40.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 469782614 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f996:61eb:8c00:45e6%15(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.17.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 486559830 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled C:\Program Files\Console>netstat -rn =========================================================================== Interface List 17...c0 cb 38 06 54 f9 ......Microsoft Virtual WiFi Miniport Adapter 13...c0 cb 38 06 54 f9 ......DW1520 Wireless-N WLAN Half-Mini Card 12...5c 26 0a 03 23 5c ......Intel(R) 82577LM Gigabit Network Connection 11...5c ac 4c f8 b8 55 ......Bluetooth Device (Personal Area Network) 14...00 50 56 c0 00 01 ......VMware Virtual Ethernet Adapter for VMnet1 15...00 50 56 c0 00 08 ......VMware Virtual Ethernet Adapter for VMnet8 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.52.2.1 10.52.2.51 10 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.105 100 10.52.2.0 255.255.254.0 On-link 10.52.2.51 261 10.52.2.51 255.255.255.255 On-link 10.52.2.51 261 10.52.3.255 255.255.255.255 On-link 10.52.2.51 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.105 306 192.168.0.105 255.255.255.255 On-link 192.168.0.105 306 192.168.0.255 255.255.255.255 On-link 192.168.0.105 306 192.168.17.0 255.255.255.0 On-link 192.168.17.1 276 192.168.17.1 255.255.255.255 On-link 192.168.17.1 276 192.168.17.255 255.255.255.255 On-link 192.168.17.1 276 192.168.40.0 255.255.255.0 On-link 192.168.40.1 276 192.168.40.1 255.255.255.255 On-link 192.168.40.1 276 192.168.40.255 255.255.255.255 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.52.2.51 261 224.0.0.0 240.0.0.0 On-link 192.168.0.105 306 224.0.0.0 240.0.0.0 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 192.168.17.1 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.52.2.51 261 255.255.255.255 255.255.255.255 On-link 192.168.0.105 306 255.255.255.255 255.255.255.255 On-link 192.168.40.1 276 255.255.255.255 255.255.255.255 On-link 192.168.17.1 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 12 261 ::/0 fe80::214:6aff:fe51:7f3f 1 306 ::1/128 On-link 12 13 2607:2600:1:850::/64 On-link 12 261 2607:2600:1:850:3d29:1839:62db:c4c1/128 On-link 12 261 2607:2600:1:850:c0e9:211a:fd05:4e0b/128 On-link 12 261 fe80::/64 On-link 13 281 fe80::/64 On-link 14 276 fe80::/64 On-link 15 276 fe80::/64 On-link 14 276 fe80::4c61:495b:229e:281e/128 On-link 12 261 fe80::c0e9:211a:fd05:4e0b/128 On-link 15 276 fe80::f996:61eb:8c00:45e6/128 On-link 13 281 fe80::fc39:9293:7d01:4a75/128 On-link 1 306 ff00::/8 On-link 12 261 ff00::/8 On-link 13 281 ff00::/8 On-link 14 276 ff00::/8 On-link 15 276 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• Is this anycast behaviour correct?

  - by etheros

  When connecting to an service provided using anycast, I am experiencing different behaviour depending on whether the request is made using TCP or UDP. With TCP, the request is made to address A, and the subsequent response also comes from A. With UDP however, while the request is made to A, the response comes from address B. Is this correct behaviour, or should the UDP response come from the same address it's sent to?

  Read the article

• How to route traffic from one subnet through a specific SOCKS proxy in other subnet?

  - by Yegor Razumovsky

  Here is my network map: Internet | | Router (192.168.1.1) | | (192.168.1.100) (wireless) MacBook ( mac os x / windows 7 / ubuntu. It doesn't matter ) (192.168.2.1) (wired) | | TargetComputer (192.168.2.2) I want to route all traffic from TargetComputer 192.168.2.2 through socks proxy running on my macbook. On target computer i can only change IP settings ( ip address, subnetmask, gateway, dns ).

  Read the article

• All wireless networks suddenly disappear every once in a while

  - by snakile

  Lately, about every 15-60 minutes, my wireless internet connection disappears. When it does I can't find any other wireless network, though such networks exist. Only after rebooting the system, it goes back to normal and finds wireless networks, but only for a while. 15-60 minutes later it's disconnected again, not finding any wireless network. I'm using Windows 7 on Lenovo Thinkpad X201s. What could it be?

  Read the article

• Inbound connections to a ubuntu machine running a VPN

  - by shanedowling

  Is it possible to open inbound connections to a machine connected to a VPN server? The machine is running ubuntu 9.10 with two network devices(a wireless card and ethernet port), I can connect to my machine locally using a local ip but when I try port forward using my router I can't connect from my external ip. Is there a way around this? I figure with 2 network devices I can vpn over one and use the other for inbound connections but I can't figure out how to do this. Thanks

  Read the article

• WDS (Wireless Distribution System) not work

  - by xdevel2000

  I've a dlink di-524 as main router (192.168.0.1) connected to Internet and a second router (192.168.0.2), a tplink wr841n, with WDS enabled and correctly configured to "join" with dlink. After I connect via wireless a laptop (192.168.0.100) to tplink and both work good but with the laptop I can't go to Internet. It seems as WDS not work. With the laptop I can only ping the tplink but other ping (the dlink or other LAN computer not responding). What's the problem? Perhaps also the dlink must have the WDS option? Thanks.

  Read the article

• Private VOIP network

  - by SuppositoryPlacebo

  I own a small private security services business. Some of my clients require 2-10 security officers per location. I'm trying to think outside the box in order to solve my communications problem. I'd rather not buy or lease hf radios or voip systems at the current rates. I'm wondering if there is an existing system, or if is at all possible, to setup a private communications network using only a server and bluetooth devices or a wifi/bluethooth combination. http://25.media.tumblr.com/tumblr_m44f0pn7BL1rwp6tgo1_1280.png I don't need "radio" per se. I just need a simple, private voip network. Is there an existing device that consists of nothing more than a wifi adapter to control a bluetooth device?

  Read the article

• What would cause my SendMail server not to acknowledge receiving a TCP Sequence?

  - by Mike B

  My TCP/IP Stack knowledge is a little rusty so please bear with me.... I have a CentOS 5.7 server with SendMail and am having seeing intermittent timeout issues sending email (particularly larger email) to other remote domains. It doesn't happen with all attachments or recipient domains. Just some. After some extended troubleshooting, I think I've narrowed it down to TCP Sequences not being acknowledged. Here's a breakdown of the TCP session from a packet capture I collected directly on my MTA (fooMTA): Packet 1 - 11: Standard TCP handshake followed by initial SMTP conversation. No errors. Packet #12 Recipient MTA: TCP sequence 231. Ack 91. Packet #13 FooMTA: TCP sequence 91. Ack 305. Packet #14 FooMTA: TCP sequence 1115. Ack 305. Packet #15 Recipient MTA: TCP sequence 305. Ack 2495. Packet #16 FooMTA: TCP sequence 2495. Ack 305. Packet #17 FooMTA: TCP sequence 5255. Ack 305. Packet #18: Recipient MTA: TCP sequence 305. Ack 5255. Packet #19: FooMTA: TCP sequence 6635. Ack 305. Packet #20: FooMTA: TCP sequence 8015. Ack 305. Packet #21: Recipient MTA: TCP Sequence 305. Ack 8015. Packet #22: FooMTA: TCP Sequence 10775. Ack 305. Packet #23: FooMTA: TCP Sequence 13535. Ack 305. Packet #24: Recipient MTA: TCP sequence 305. Ack 10775 Packet #25: FooMTA: TCP Sequence 14915. Ack 305 It keeps going like this with my server still thinking it hasn’t received sequence 305… in response the remote side eventually retransmits its prior data thinking that it never arrived. Eventually the gap gets so large that no new data is sent and the remote MTA keeps retransmitting old stuff. This contributes to an exponential backoff and eventually the remote side gives up. What’s strange to me is that I see the “missing” TCP sequence (305 in this case) arriving back to my server (via a packet capture collected directly from fooMTA) So I don’t get why my server keeps asking for it. Could this be firewall related? What would be the next step in troubleshooting?

  Read the article

• Switch between network configurations via command line in fedora 17

  - by Mike Fairhurst

  I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

  Read the article

• Same network same switch but computers can't talk "ping"to eachother [closed]

  - by Sue

  Possible Duplicate: How does IPv4 Subnetting Work? Each computer(all 2 of them) can ping the router but can't ping each-other and firewall is off. Same default gateway, IP address very similar (just two number away at end) but the subnet mask is different between these two computers. One ends in 192 the other 224. There is a switch between them that then connects to the router. Why can't the computers ping each-other?

  Read the article

• How to set up a home WEB server Ubuntu and test over LAN Windows 7 XAMPP Lampp

  - by thejartender

  I am looking for a guide on how to set up a local home server that will also be used as a web server. I have an old desktop with Ubuntu 12.10 and wish for this to be used as my central web and local server. I also have multiple Windows 7 systems at home that I wish to be part of this network and a wireless router. Can someone provide me with assistance on where to start (perhaps just the home network) or refer me to a guide on how to do this?

  Read the article

• Disable Network settings (TCP/IP & DNS) on Windows 7 Ultimate

  - by TiD91

  i also read this discussion here How to disable Tcp/Ip settings in windows 7 via GPO? about what i want to do but i still have problems. So here i am: i have a desktop pc with two accounts, both with Administrative rights. One is used by the entire my family, in particular by my brother. The problem is that i set some DNS and IP configurations to let be possible the VNC connection from remote. Now i would like to disable the network settings (TCP/IP and DNS) to prohibit my brother to change it preventing me to connect to it. So how can i do this? I set the policies from GPO but i still can change these settings from his account. Here's a pic of Registry Keys: http://imageshack.us/a/img339/3310/famigliapc2012092017274.png what didn't i do? Thanks in advance for your help. Rub|TiD

  Read the article

• How can I ensure that my static ip address is read from /etc/network/interfaces rather than dhcp?

  - by jonderry

  This is a follow up to the following question. I'm trying to set a static IP by changing /etc/network/interfaces to the following: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.2.133 netmask 255.255.255.0 gateway 192.168.2.1 dns-nameservers 8.8.8.8 and then running /sbin/ifdown eth0; /sbin/ifup eth0. However, the change in IP address doesn't appear to take effect without editing /etc/dhcp/dhclient.conf and commenting out the following before running ifdown; ifup: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, dhcp6.name-servers, dhcp6.domain-search, netbios-name-servers, netbios-scope, interface-mtu, rfc3442-classless-static-routes, ntp-servers, dhcp6.fqdn, dhcp6.sntp-servers; Strangely, after commenting out this line, running ifdown; ifup works, but when I uncomment it, the behavior does not revert to the previous behavior of ignoring changes to my settings in /etc/network/interfaces (this doesn't seem like a problem, but I really need to be able to repeat this problem so that I can be confident that my solution is robust) Also, I'd rather not have to edit /etc/dhcp/dhclient.conf to change my static IP since it seems I should be able to do this by only editing interfaces. Can anyone explain the issues I'm seeing above and suggest the best way of making changes to static IP addresses take effect that admits reproducibility so that I can be sure that my approach works?

  Read the article

• How to write rules for persistent net names?

  - by ndemou

  I know that a process generates persistent network card names based on rules found in /lib/udev/rules.d/75-persistent-net-generator.rules. I also know how to completely disable this process with a simple echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules but I've read that I "could also write my own rules file to give the interface a name — the persistent rules generator ignores the interface if a name has already been set" (/etc/udev/rules.d/README confirms that this is possible). Do you have any pointers to documentation about how to write such rules? (I mostly care about Debian/Ubuntu and a bit less for CentOS) As a specific example of why I want to write custom rules: I have two identical servers with one onboard LAN and one PCI LAN. In case of HW failure I want to be able to move disks from HW#1 to HW#2 and it's important for eth0 to continue pointing to the onboard card and eth1 to the PCI card (no one wants to mess with cabling in the middle of a HW failure panic). My current workaround works but is a lot of work[1] so I wonder if writing custom rules would allow me to express something simple like this: cards with MAC A or B should be named eth0 cards with MAC C or D should be named eth1 follow default naming scheme for anything else [1] install the OS in HW#1 and keep a copy of /etc/udev/rules.d/70-persistent-net.rules. Move the disks to HW#2 and keep a second copy of the same file. Concatenate the two copies and manually edit the NAME="ethX" part. Replace /etc/udev/rules.d/70-persistent-net.rules with my version. Finally disable auto-creation of a new 70-persistent-net.rules using echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules

  Read the article

• Redirect traffic to local address so iOS speedtest app measures LAN speed

  - by ivan_sig

  I have mounted a Speedtest Mini server on a local LAMP, so I can test my LAN speeds effortlessly just by opening the URL with a Flash enabled web browser, the thing is, I want my iOS and Android devices to test with the LAN server too, not with the WAN, as I'm trying to measure LAN-Only performance. Is there a way so I can redirect the traffic intended to an specific external IP (The one of the real server) to my local server?. I know the servers IP as a short Wireshark analysis gave me the data, but still searching for a way to make that redirect. I have Jailbreak and root on my devices, so playing with system files is not a problem. I've tried mounting a proxy and making redirects by the hosts file and domain names, but it looks like Ookla's app relies on IP address only.

  Read the article

• wifi connection turns off oll the time

  - by er-v

  Hello! I realy need help with one strange problem. I have a wifi network in my appartment with wireless N home router Trendnet tew-652BRP. Everething work fine for three of my laptops, but I have one PC with D-Link DWA-140 adapter. It looses connection 2-3 times in 5 minutes. There is following messages in my system log when it does so: The browser has forced an election on network \Device\NetBT_Tcpip_{9537A5C1-3B43-4C56-B94C-CE69A257C3AD} because a master browser was stopped. The TCP/IP NetBIOS Helper service was successfully sent a stop control. The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)] Comment: None The TCP/IP NetBIOS Helper service entered the stopped state. in order of appearence. How can I stop it? I have the latest driver installed.

  Read the article

• Setting up virtual network in VMware workstation

  - by Saif Bechan

  I am playing around with VMware workstation and am trying to set up a small virtual network. I am having a little trouble with this I hope somebody can help me out. I want to have all the different virtual machines to have different internal IP adresses so I can ping them SSH etc, from within my windows machine. I am directly connected to the internet without a router, so using a bridged connection does not seem to work. The other options NAT and host-only do not seem to work also. I think i need to create a new adapter. I am testing this out with a virtual image of linux debain 5.0 lenny. I have WMware Workstation 7 with virtual network editor. Can anyone guide me in the right direction.

  Read the article

• command line bandwidth limiter for windows

  - by jackhab

  Please, recommend network bandwidth limiter for windows which can be controlled from command line. No need for fancy options, only limiting of up and down traffic on a host required.

  Read the article

• Command or tool to display list of connections to a Windows file share

  - by BizTalkMama

  Is there a Windows command or tool that can tell me what users or computers are connected to a Windows fileshare? Here's why I'm looking for this: I've run into issues in the past where our deployment team has deployed BizTalk applications to one of our environments using the wrong bindings, leaving us with two receive locations pointing to the same file share (i.e. both dev and test servers point to dev receive location uri). When this occurs, the two environments in question tend to take turns processing the files received (meaning if I am attempting to debug something in one environment and the other environment has picked the file up, it looks as if my test file has disappeared into thin air). We have several different environments, plus individual developer machines, and I'd rather not have to check each individually to find the culprit. I'm looking for a quick way to detect what locations are connected to the share once I notice my test files vanishing. If I can determine the connections that are invalid, I can go directly to the person responsible for that environment and avoid the time it takes to randomly ask around. Or if the connections appear to be correct, I can go directly to troubleshooting where in the process the message gets lost. Any suggestions?

  Read the article

• 'IPv6' Newbie with IPv6 address assigment

  - by Cute Puppy

  I am new to IP v6 and I am looking to translate some existing private IPv4 addresses into v6 address assignment. Can someone please help me to answer/explain the questions below? If I have an v4 address of: 10.10.0.0/22 10.10.1.0/22 10.10.2.0/22 10.10.3.0/22 10.10.8.0/20 10.20.1.0/24 What will the new v6 address to be? I have been looking online @ http://www.subnetonline.com/pages/subnet-calculators/ipv4-to-ipv6-converter.php or other sites, Seems like they translated it directly to be: fe80::a0a:0 /118 fe80::a0a:100 /118 fe80::a0a:200 /118 fe80::a0a:300 /118 fe80::a0a:800 /118 fe80::a14:100 /120 Can someone please explain to me how we get to /118 from either "/22 or /24" (1. and 5) In addition, I would like to create the new private address based on the Unique local address "fc00::/16" How do I expand from there? Any help is greatly appreciated it!! Thanks,

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Windows Server 2003 Is there a limit on number of TCP connections per process?

  - by aceinthehole

  We are running into issues with BizTalk host instance intermittently going down. One of the things that we are worried about is the number of FTP connections a single host instance is making which could easily reach into the hundreds perhaps sometimes thousands, depending on traffic. My question is Windows Server 2003 Is there a limit on number of TCP connections per process? If so would putting each application in it's own host instance potentially solve the problem.

  Read the article

• WLC 4400. Get IP

  - by Edward Connelly

  I have three SSID. one is a guest network and I'm having problems with lease times. Its set for web authentication so it passes IPs out even if someone doesn't try and authenticate. Is there a way to get that IP back and not hand another to that mac for a period of time? Poor planning and we didn't allocate enough address space, and we are sandwitched. We could go with another address, but we would have to reconfig lots. since its guest its vlan'd with no access to anthing but the firewalls. would have to change ACLs and routes and interfaces. if it isn't possible we will just have to go that route, just thought there might be an easier solution. session timeout is enabled with 1 hr lease time is set to 4 hrs. no helper DHCP and internal DHCP is set with the space split across three WLCs (60 waps split across those as well).

  Read the article

• Can I use my Belkin router as a repeater?

  - by Kyle R

  I've got a brand new, unopened Belkin N600 DB router (yay 50% off sale), and I can't seem to figure out if I can use it as a repeater. As far as I can tell, it doesn't support DD-WRT or Tomato, but I'm wondering if there may be some way to rig it up to repeat Wifi. Also, I really need to know before I open it, because, being a bit tight on money at the moment, I'll probably sell it if I can't use it as a repeater. Finally, two caveats: I can't use the other wireless router for anything other than broadcasting straight from the modem (parents are paranoid about anything technological). I can't run ethernet to the second router due to the layout of the house. Thanks so much for the help everyone--if I'm being vague, tell me! EDIT: Also, the manual here is pretty useless on this topic as far as I can tell.

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >