Search Results

Search found 7435 results on 298 pages for 'hardware'.

Page 250/298 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• PC shut downs automatically after 10-20 second. No POST screen, no beeps

  - by emzero

  I have this not-so-old computer that's not being used for a year or so. Specs: Motherboard: ASUS PN5-E SLI CPU: Intel Core2Duo E4300 RAM:2x2GB SuperTalent DDR2-800 VGA: Zogis GeForce 7950GT PSU: Vitsuba San-55-S 550w HD: No hardrives yet When I power on the computer, everything seem to start, but right away the whole system shuts down. I've removed and changed the RAM sticks, take out the VGA, everything I could think of. So what could it be causing this? The PSU? The motherboard is dead? The CPU? Any help to isolate the problem will be useful. Thanks PS: Please don't close the question, this could be helpful to anybody having a similar problem, even with different hardware. UPDATE I've removed the old thermal paste and apply a brand new one. I also cleaned every dust using a high pressure gas dust remover. Checked for bad capacitors, all of them seem ok. Opened the PSU, removed big giant dust balls, cleaned with high pressure dust remover. Still the same problem, but now it stays powered on for almost 20 seconds maybe. But no POST screen, no beeps at all, nothing. So I suspect it's a motherboard or PSU failure. Unfortunately I don't have an energy tester to test the PSU... Don't know what else to try. I don't have another 775-motherboard to test the CPU, RAM and VGA with it.

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  I'm having some problems installing CentOS 5.5 Final (i386) onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up and gives you the option on how to boot into the DVD, I'll press enter to go into the graphical installer. The screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours). I then booted into it again and tried using Linux Text thinking it was a problem with the graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point I think it's a hardware problem. The server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) configured for RAID 0. (There is also an option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. Edit Typing "text" doesn't change a thing. Still stuck at the blinking cursor. I looked it up and it's really the same thing as typing "linux text", which as stated in the first part of my question, I've already done.

  Read the article

• MD RAID 1 with external bitmap doesn't fully resync

  - by user64744

  I have an interesting configuration: dual boot system with a RAID 1 that needs to be visible in both Windows and Linux. The Windows install is Win 7 Enterprise, and the Linux install is Kubuntu 10.04. To get the RAID to work, I set it up using Windows's "Dynamic Disks" RAID 1, and brought it up in Linux using MD with no persistent superblock, and a write-intent bitmap on another partition. (Without this bitmap, MD had no way of knowing that the array was in sync, and would do a complete resync every time the array started.) The array is assembled like so: mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 I expected that the first time I ran this command, it would resync the array, write out a bitmap with no dirty chunks, and all would be good. This wasn't the case: after completing the resync, the bitmap was mostly clean, but about 5% dirty blocks remained, as revealed by mdadm -X /var/local/md1.bitmap I didn't mount the filesystem on /dev/md1 or touch it in any other way. I then found that stopping and restarting the array: mdadm --stop /dev/md1 mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 did indeed read in the bitmap, with an ensuing resync that went quickly because most of the blocks were marked clean. The confusing part is that this resync further reduced the number of dirty blocks, but still did not remove all of them. By repeatedly stopping and restarting I could slowly bring the dirty block count down to around 0.6%, where it seemed to level out. Any ideas what could be causing this? It smells to me of a race condition somewhere that leads to blocks either being skipped over during synchronization or not properly cleared from the bitmap, but I really have no evidence to prove this. It doesn't look like hardware issues since both drives are new and have zero read errors and reallocated sectors reported by smartctl -a.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Simulating audio playback on headless linux server

  - by afro

  Hi people, We have a headless linux server (Debian 5) we use for runnin integration tests of our web-page code. Among these tests are ones implemented using Selenium, which practically simulates a user browsing our pages and clicking on things. One of these tests is failing now, because it involves starting a flash-based audio player and checking to see whether the progress bar gets displayed properly. The reason this test fails is that there is no way to play the audio, and no sound card on the machine, which has simple webserver hardware. So, my question would be: Is there a simple way of giving a program the impression that its audio output is being processed, and playback is taking place? I don't have to record the playback, or redirect it or anything like that, just a dummy soundcard, like the dummy X-server we aer using, which actually does not need to display stuff. I have tried using JACK, but it's too complicated, and the documentation does not even answer this very simple question. I also installed alsa on the server; it 'pretends' to run, but when a program tries to play audio, just spews error and debug information having to do with the non-existence of a soundcard. It would be really awesome if one of you has a simple answer to this question. Cheers, Ulas

  Read the article

• Can I take my ReadyNAS drive in Raid1 and plug it straight into new different machine?

  - by jacko

  I would assume that I can just take my HDD out of my NAS (in raid1 mirror) and plug it into another enclosure and have it work off the bat but I'd like to make sure... Any ideas? Edit: My current setup is a Netgear ReadyNAS in (hardware) raid1. I'm hoping to replace this with a home theatre type PC (possibly running Ubuntu), and would like to migrate my data without having to do a bulk transfer over my network between the 2 machines. Can anyone confirm the case for the Netgear ReadyNAS? Edit: Ok after further reading it seems that the ReadyNAS Duo formats my drive as ext3 in 16k blocks. There are instructions for mounting a drive into a linux box here: Mounting Sparc-based ReadyNAS Drives in x86-based Linux There is also talk about a linux image here: ReadyNAS Data Recovery - VMware recovery tool I'm not sure whether this means they ReadyNAS actually implements software raid under the hood, or what? So it appears like it IS do-able, but do any of you linux guru's know whether this is viable and whether the fact that they are in raid 1 affect matters?

  Read the article

• No apparent reason for high load average

  - by Oz.

  We have several web servers running on Amazon (ec2) c1.xlarge, over Amazon AMI. The servers are duplicates of each other, running the exact same hardware and software. Each server spec is: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge A couple of weeks ago we have run a yum upgrade on one of the servers. Starting on this upgrade the upgraded server started showing a high load average. Needless to say, we did not update the other servers and we can not do so until we understand the reason for this behavior. The strange thing is that when we compare the servers using top or iostat, we can not find the reason for the high load. Note that we have moved traffic from the "problematic" server to the others, which have made the "problematic" server less crowded in terms of requests, and still his load is higher. Do you have any idea what could it be, or where else can we check? Many thanks for the help! Oz. # # proper server # w command # 00:42:26 up 2 days, 19:54, 2 users, load average: 0.41, 0.48, 0.49 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/1 82.80.137.29 00:28 14:05 0.01s 0.01s -bash pts/2 82.80.137.29 00:38 0.00s 0.02s 0.00s w # # proper server # iostat command # Linux 3.2.12-3.2.4.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 9.03 0.02 4.26 0.17 0.13 86.39 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.63 1.50 55.00 367236 13444008 xvdfp1 4.41 45.93 70.48 11227226 17228552 xvdfp2 2.61 2.01 59.81 491890 14620104 xvdfp3 8.16 14.47 94.23 3536522 23034376 xvdfp4 0.98 0.79 45.86 192818 11209784 # # problematic server # w command # 00:43:26 up 2 days, 21:52, 2 users, load average: 1.35, 1.10, 1.17 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/0 82.80.137.29 00:28 15:04 0.02s 0.02s -bash pts/1 82.80.137.29 00:38 0.00s 0.05s 0.00s w # # problematic server # iostat command # Linux 3.2.20-1.29.6.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 7.97 0.04 3.43 0.19 0.07 88.30 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.10 1.49 76.54 374660 19253592 xvdfp1 5.64 40.98 85.92 10308946 21612112 xvdfp2 3.97 4.32 93.18 1087090 23439488 xvdfp3 10.87 30.30 115.14 7622474 28961720 xvdfp4 1.12 0.28 65.54 71034 16487112

  Read the article

• Cannot connect to windows server by name over vpn connection

  - by ErocM

  I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

  Read the article

• Is USB supported in safe mode on XP?

  - by Hugh Allen

  According Microsoft, "Universal Serial Bus Devices Do Not Work in Safe Mode" under XP. However, in my testing this is incorrect. USB keyboards, mice and flash drives seem to work fine in safe mode (I made sure the BIOS was not providing support). This makes sense because a failure of a standard input device would be, in Microsoft parlance, a "bad user experience". So, Is USB supported in safe mode on XP? If your answer is no (agreeing with Microsoft), please provide a test case, preferably in a virtual machine, where a standard HID keyboard or mouse fails. Please state hardware / BIOS / OS configuration. Note that you will need a PS/2 keyboard attached in addition to your USB device(s) in order to use the boot menu. Virtual machine software usually emulates a PS/2 keyboard. Alternatively, you could add the /safeboot switch to boot.ini. If your answer is yes, please provide a link to some supporting documentation (either from Microsoft or someone authoritative). Your answer might be "devices X, Y and Z are supported but nothing else", in which case also give a link.

  Read the article

• Backup plan for linux webserver in small business?

  - by radman

  Hi, I am currently in the process of writing a backup plan for the webserver in use by my business. I am very new to this area and have a few ideas about how things should work but am unsure of what tools to use and what sort of restore process is appropriate. I'm looking for something relatively simplistic and it doesn't have to be 100% paranoid just enough to give me a reliable backup. Speed is not of the essence and there is not going to be a live fallback in place. The backup will be onto a single hdd that will be stored onsite (no option for offsite as yet). Backups will be taking place weekly. I am constrained by both time and money which is why I'm aiming for a good enough solution. Is taking an image of the webserver system drive periodically and using that as the backup appropriate? Should I be testing that the backups restore correctly every time that I perform one? This is a bit broad but what setup would you use if you were in my place, given the services I am running? Should I add additonal machines and split the services? Any advice is much appreciated! See below for server details Webserver Platform Linux Ubuntu server Running mail-server svn-server mediawiki wordpress apache-webserver Hardware single 500gb sata drive Architecture Single machine behind router (with firewall) accessible to the internet.

  Read the article

• Splitting build cross the network?

  - by Dandikas

  Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

  Read the article

• Terrible noises from subwoofer of ACER Aspire 6930 with Realtek sound chip

  - by OneWorld

  After approximately 5-15 min of listening to music my subwoofer begins to make terrible noises. He's just "coughing". That began after 6 months I had this computer. Now I found out, that I can temporarily fix this problem by "restarting" the audio stream of the application that plays music. For example reloading last.fm page (reloads the flash file). Another way to reset the audio playback is switching the speaker configuration shown below in the screenshot. According to many posts on the internet like http://www.tomshardware.co.uk/forum/52918-20-acer-aspire-6935g-speaker-problem ACER support isn't any help Exchanging hardware doesn't fix the problem Even the later models have this problem Turning off the volume of the subwoofer is not an option to me. I still have warranty (I bought an extension of one year). I already tried about 15 versions of the Realtek driver with no success. I am not sure but MAYBE the problem did not occur on the original windows vista that was shipped with this computer. However, I removed the original windows for good reasons (english). What do you suggest me? Did anyone fix this problem? Maybe by writing a script which resets the audio streams every 5 minutes? Shall I take the effort to deal with the acer support until they give me another model? (I won't have a computer than for a longer time, will spend money on telephone hotlines (1,30 EUR / min)......) Here are additional infos, if they are any help: Windows 7 64 Bit (Original was Windows Vista Home Premium 32 Bit) All specs Audio driver version:

  Read the article

• Managing disk in a VM

  - by dst

  I'm replacing my two old rack servers with a new one that has plenty of power to take over the functionality my current servers. The server is a 4U rack mount with 16 3.5" SAS drive bays, two 2.5" bays, a Xeon E3-1230v2 CPU and 32GB of ECC RAM. My issue is the following. I would like to have a FreeBSD file server with ZFS managing disks. However, I need other VMs for e.g. a shell/git server, mail server etc. I'm wondering how to deal with the following issues: I want ZFS to fully manage the disks, so I'm not using any hardware RAID. Should I pass the SAS controller directly to the FreeBSD system as passthrough PCI? I want to maximize the reliability of the setup. On what disks should I install the hypervsor and keep server system disks? For (2) I have the option of having a RAID setup on the SAS controller and using that as system disk to store the hypervisor as well as VM images. However, this makes PCI passthrough to the file server impossible. Another option is using the two 2.5" bays. In terms of reliability how are SSDs compared to e.g. WD RE4 disks? Would it make sense to have two SSDs in software RAID as boot disks for the hypervisor or should I just go with e.g. WD RE4 disks in a software RAID setup. I also need to think about where to store the mails for the mail server, but this could be done over NFS between the VMs. BTW, this is for home use, so the load is not really that big. What I'm looking for is best practices for splitting up a server.

  Read the article

• Want to use something like Citrix XenDesktop, Free Alternative?

  - by Chris

  I'm looking to go into IT, general office server management, and it looks like XenDesktop would be a awesome tool to use. If I get it right, you would store a central image of the OS you want to deploy (in an iso file) on the main server. Then use XenDesktop to pull that image down to the client, and it will then boot the OS inside of the virtual machine. Does it download the image of the OS and store it locally (like cloning the VM onto the client?) I'd love to find a free (possibly open source?) alternative to this, I keep on hearing about KVM in Linux and PXE booting a minimalistic OS to use remote KVMs.... Would that be what I'm looking for? Ideally, I'd like a system.. - That allows me to manage one central image for multiple clients (virtualized hardware) - Easily boot a thin client OS that connected to XenDesktop. Would those things be possible with some kind of free alternative? Some guidance would be greatly appreciated.

  Read the article

• MSSQL error: consistency-based I/O error - can it be caused by an MSSQL or OS problem?

  - by Philipp Keller

  This is what I saw in the windows error log: SQL Server detected a logical consistency-based I/O error: incorrect checksum (expected: 0x19fedd20; actual: 0x19fed5e3). It occurred during a read of page (1:1764) in database ID 6 at offset 0x00000000dc8000 in file 'D:\mssql\local_repository_pbdiffimport.mdf'. Additional messages in the SQL Server error log or system event log may provide more detail. This is a severe error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. I ran dbcc checkdb which told me I should restore with option REPAIR_ALLOW_DATA_LOSS, so I eventually ran DBCC CHECKDB (my_db_name, REPAIR_ALLOW_DATA_LOSS) WITH NO_INFOMSGS But that resulted in about 2'000 rows being lost. I restored a backup but now I'm afraid this will happen again since we already had a consistency problem in the same database about 2 weeks ago but then it happened in an index (recreated indexes solved the problem). We have investigated the discs - RAID5 looks good, no errors, and also none of the disc-check-utilities have revealed any hardware problem. Can this be caused by OS (Windows Server 2003) or by MSSQL (MSSQL Server 2005)?

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• Can't get intel atom g-500 video driver to work with ubuntu 10.10 netbook edition.

  - by Matthew

  First of all I am completely new to Linux, so if you respond, please do so in a 'linux for dummies' tone so that my brain will be able to process it. I recently installed ubuntu on my dell mini-inspiron 1010. It has one GB of ram and an intel atom processor that uses the intel 500 graphic accelerator driver for windows and can run 1024x768 comfortably in xp. When I was installing ubuntu had quite a bit of trouble with my display and I am still unable to adjust my settings from 800x600x0x0 and there is no hardware acceleration. I visited the intel site and installed the linux drivers with the help of a friend but still no change. I tried adding resolution settings through xconf but they could not be applied even after I added the values. I am probably going about this totally wrong, but I've spent quite a lot of time browsing through forums and still haven't found a solution. Any help would be greatly appreciated. Also any other beginner tips that you have would be much appreciated. Thanks in advance, Matt

  Read the article

• Production monitoring for EC2 instances

  - by Janine

  I'm setting up my first production instance on EC2 and want to make sure I have all necessary monitoring in place. There are three different types of things I want to monitor: Is the instance running? EC2 instances can be terminated without warning if the underlying hardware fails, and as far as I know they aren't automatically restarted. So if not, start it back up. Is UNIX running properly? This is the usual stuff about CPU load, disk space, etc. Is the website responding? If not, restart it. I initially set up Nagios on a physical server outside the cloud, but it is really only helpful for item 2. It can tell me if the instance is gone or if the website is not responding, but as far as I can tell it can't execute any commands to fix the situation. My Googling on this subject has yielded a plethora of options - Cacti, Monit, God, Ganglia, and probably more I'm forgetting now. I don't have time to research them all. I am aware of Amazon's Cloudwatch but it doesn't seem to do anything that my Nagios installation doesn't already do. If you already have something like this in place, can you please share what has worked well for you?

  Read the article

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• Errors with Using Webcam

  - by C.G.

  I have been having some issues accessing a webcam from my machine. Sometimes (not always) when I run a program that accesses the device (cheese, guvcview, and code using openCV), I get either of two messages, which lead to the program crashing. The first occurs after running the webcam for some time. libv4l2: error dequeuing buf: No such device VIDIOC_DQBUF: No such device The other will occur without even letting me have a chance to run the webcam. libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON - Unable to start capture: No space left on device Occasionally after getting these errors I will also receive a message saying that no such device can be found for subsequent runs. Other than the times that the "No device found" message appears the webcam appears when I use lsusb. My machine runs Linux Fedora 16, and the webcam is a Logitech C920. I do have ffmpeg installed, and I have been able to run the web camera many times in the past without errors. What is particularly puzzling about these errors is that they just sprung up this past weekend. No new software or hardware has been installed on this machine recently; I haven't changed any settings recently either. It could possibly be a driver issue, but I don't know what could have changed which could lead to this issue. Any attempts at researching this problem has been fruitless as this seems to most commonly occur with multiple webcams. I am only working with one device. I'd appreciate any advice for this problem, as this has become a bit frustrating.

  Read the article

• picking a linux compatable motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• Finding useful crash-information in Windows 8 Consumer Preview

  - by Lukas Knuth

  I'm currently diving into C# and wanted to play around with the new Metro-styled-applications introduced with Windows 8, so I updated my Windows 7 to Windows 8 Consumer Preview. The problem I'm facing right now is, that the system freezes after 3-5 minutes. It does not take any input from the keyboard or mouse and it does not recover (at least not in less then 10 minutes). Since I have a background in Linux, I'd like to find some information about the cause of the freeze, but I have no idea where to search. I checked the system-logs (under "System Control" - "Management") but they only record that the system was shut down unexpectedly (doe to the face that I held down the power-button to reboot the PC). There is no useful crash-information in there. I don't want to spend hours on randomly reinstalling drivers and doing things that "might help". Isn't there any place I can find some useful information about the freeze? Before you ask: I installed Windows 8 as an updated on my old Windows 7 installation (which worked fine by the way). My hardware fits the minimum requirements (specs can be found here, the MacMini 3,1 model with 2GHz processor). I have updated the graphics-card drivers to the newest Windows 8 drivers from nVidia.

  Read the article

• RRAS Problem routing to central site from RRAS server only?

  - by TomTom

  Given is an office connected to headquarters using a RRAS bridge (2 virtual machines using RRAS to route between the two networks). Naming: The office is A, the RRAS on A is a-lnk. THe headquartters is B, b-lnk the RRAS machine there. The VPN works perfectly - machines can ping and work between the sites. Domain controllers on both ends replicating, DFS working, remote desktop working. All in all... everything is fine. EXCEPT: a-lnk itself can not reach any machine in B. This would normally not be troublesome (noone ever does anything on a-lnk), but there are two exceptions: * a-lnk is supposed to get it's license from a KMS in B, so not being able to reach B means it is not prolonging. * a-lnk is supposed to pull updates from a WSUS in B - and not being able to reach B means - no updates. Given that thigns work (and security is a minor issue - A-lnk is not reachable from the internet as it is behing a NAT hardware anyway) this got not handled for months. I just wan to get this item ticked off now. Anyone an idea what this is? It definitely is not a "dns does not work" or "routing in general is bad" item, as any computer in A can connect to any computer in B, and the other way arount - only the RRAS computer itself seems to do something really awkward. Platform for both: 2008 R2 standard.

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >