Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 252/1617 | < Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >

• What is causing my internet to be slow on one laptop but not the other and only at a distance?

  - by Matt Case

  I have a newer laptop, purchased within the last year (acer aspire 7740). This laptop does not have any problem connecting to wireless networks and indicates that the signal strength is excellent on most of the wireless networks I connect to. When the laptop is within 10 feet of my wireless router it gets 30 down 10 up. When it is farther away than 10 feet it will be lucky to get 3 down and 1 up. I also have an older laptop, purchased in 2005, that has no problems at all at the same range. None of my phones, gaming consoles or tablets have this problem. I am beginning to think that the problem must be some hardware defect with the wireless card. I can provide additional information if needed. Just thought I'd check to see what others thought because I've been working on computers my whole life and have never heard of this happening. I have also tried to change the channels on my wireless router and have had no success with this idea.

  Read the article

• TCP: Treason uncloaked!

  - by hurikhan77

  On one linux server (Gentoo hardened), we are experiencing bursts of the following messages in dmesg from time to time: TCP: Treason uncloaked! Peer xx.xx.xxx.xxx:65039/80 shrinks window 4094157295:4094160199. Repaired. Is there anything we should take care of or is this normal?

  Read the article

• Where would an S3 upload speed cap originate?

  - by CoreyH

  I do a ton of uploading to S3 and am experiencing capped speeds and I can't quite figure out how to address it. The setup: Windows Server 2008 R2 x64, external HD, using a Java based upload tool called Jsh3ll and custom VBS scripts to kick the jobs off. Running one process at a time, I am always limited to about 4mbps. I have FiOS at 35/35mbps speeds, so it isn't an outright limit. AND, I can run parallel instances and can go all the way up to 35mbps, so I know the problem isn't gateway/nic/machine/amazon related. Running parallel instances works to a degree as a solution, but increases the complexity of my workflow greatly. Solving this would make my life dramatically easier. When I was first doing this I was playing around with a bunch of Windows TCP parameters and was able to briefly get unconstrained bandwidth, but it wasn't repeatable. Thoughts?

  Read the article

• 'Slow down' A DHCP server on purpose.

  - by Ced

  As the title implies, May look like a silly question, But what i'm trying to do, Is to have 2 DHCP servers in one network. One only leases IPs to Bootp clients (And if the client re-requests immediately after leases again) And one DHCP server, which is builtin with my PFsense router, that leases the non-bootp clients so they can access the internet and other network resources. I know by chance that PFsense uses ISC-DHCPd. Maybe they have a delay option? All i need to do to make sure the bootp/PXE boot clients get the proper address, is slow down the DHCP server in the PFsense box. Question is how. Anyone ideas? Thanks in advance

  Read the article

• Comunication from Server to Client + Client LAN

  - by Filipe YaBa Polido

  I'm having some trouble with some network setup. I've tried OpenVPN, SocialVPN, Hamachi, still it is not working. This is my setup: Server A: NIC 1 with internet public address, NIC 2 to LAN Client B PC: NIC 1 (192.168.10.2) connects to router 192.168.10.1 Client B Device: 192.168.10.3 (Configured via software, can't do much here) Problem: Server A must connect to cliente device B. (I can install software needed at Client B PC). However... I can't change the router to some model with VPN like Draytek or Cisco :( OpenVPN fails at bridging, PC B can ping Server A, but Server A can't ping Device B, only PC B. What else can I do?!?!?

  Read the article

• Netgear genie says my Internet is off, while Windows claims I am connected

  - by Manu

  I'm connected via wifi to my ISP's router/modem. While Windows says that I'm always connected, I keep getting messages from Netgear Genie that I've lost contact to the Internet, and I cannot access webpages until it comes back. There are two other computers in the house, one connected to the router via ethernet, the other via wifi, both seem to have no such problems. I've wondered if Netgear genie itself was the problem, but I am regularly disconnected even if I uninstall it. And I'd rather have it since it accurently tells me if I'm connected or not. Why does windows says I'm online if I can't access any online game, or website ? Is "netgear genie" the problem ? I've removed the connection, recreated it, I've even copied the settings to a usb key from the computer that has wifi access.

  Read the article

• My laptop can connect to every wireless network except fios

  - by going crazy

  I have always been able to connect to every wireless router secured or unsecured wep or wpa. I had Fios installed and could not connect. Verizon suggested it was my computer and gave me an outside wirless drive to use, it worked. I got rid of fios and went back to comcast and threw out the drive, but now 2 years later, I am sitting at my friends house haveing the same problem. My tech savy friend told me it is a firewall setting or something in my antivirus software, but I disabled them both and still nothing works........Funny it is only FIOS

  Read the article

• What is the "in-the-wire" size of a ethernet frame? 1518 or 1542?

  - by chrisapotek

  According to the table here, it says that MTU = 1500 bytes and that the payload part is 1500 - 42 bytes or 1458 bytes (<- this is actually wrong!). Now on top of that you have to add IPv4 and UDP headers, which are 28 bytes (20 IP + 8 UDP). That leaves my maximum possible application message to as 1430 bytes! But by looking for this number in the Internet I see 1472 instead. Am I doing this calculation wrong here? All I want to find out is the maximum application message I can send over the wire without the risk of fragmentation. It is definitely not 1500 because that includes the frame headers. Can someone help? The confusion is the the PAYLOAD can actually be as large as 1500 bytes and that's the MTU. So now what is the size in-the-wire for a payload of 1500? From that table it can be as big as 1542 bytes. So the maximum app messages I can send is 1472 (1500 - 20 (ip) - 8 (udp)) for a maximum in the wire size of 1542. It amazes me how things can get so complicated when they are actually simple. And I have not clue how someone came up with the number 1518 if the table says 1542.

  Read the article

• Use name instead of IP address for home network

  - by abney317

  I have IIS7 on my computer, and I can access it through other computers in my house on the same network through my computer's IP address - 192.168.1.10x Instead of typing in http : //192.168.1.10x/ I want to be able to go to http : //somename/ I know you can change the hosts file to add it but I'd have to do that on each computer and I'd still have to type in the IP to access it from my iPod/Wii... etc.

  Read the article

• Use name instead of IP address for home network

  - by abney317

  I have IIS7 on my computer, and I can access it through other computers in my house on the same network through my computer's IP address - 192.168.1.10x Instead of typing in http : //192.168.1.10x/ I want to be able to go to http : //somename/ I know you can change the hosts file to add it but I'd have to do that on each computer and I'd still have to type in the IP to access it from my iPod/Wii... etc.

  Read the article

• How do I get a 300Mbps connection over 802.11n?

  - by Daniel Schaffer

  I just bought a new wireless setup, consisting of a Cisco E2000 router, Edimax 7718un USB adapter for my laptop and an Edimax 7728in PCI adapter for my HTPC (which isn't in a location I can run cat5 to). I have to stay in the 2.4GHz band because I have an iPhone and a Wii that will need to connect. I'm aware that 11g devices will drop speeds for 11n devices, but they aren't connected yet. The fastest connection I've been able to get, with the router within 5 feet of either the laptop or HTPC is 144Mbps. The router has settings for "20MHz" and "Auto (20 MHz or 40Mhz) channel width, which I've set to the "Auto" setting. I haven't been able to find anything similar for either of the Edimax adapters. This is the first I've dealt with 11n, so I'm not even sure what else could be causing a problem. How do I get up to 300Mbps, or at least a fair bit closer?

  Read the article

• Is it safe to use a single switch for multiple subnets?

  - by George Bailey

  For a moment, forget about whether the following is typical or easy to explain, is it safe and sound? Internet | ISP supplied router x.x.x.1 (public subnet) | switch-------------------------------------+ | (public subnet) | (public subnet) BVI router (switch with an access list) NAT router | (public subnet) | (private subnet 192.168.50.1) +--------------------------------switch----+ (both subnets) | | computer with IP 192.168.50.2 ------+ +----computer with IP x.x.x.2 I don't plan to implement this setup, but I am curious about it. The 50.2 computer may send a packet to the x.2 computer, but it will use 50.1 as the router, since 50.2 knows that the subnet is different. Would this result in the packet being received twice by the x.2 machine, first directly through the switch, second by way of the two routers? Do you see any problems with this aside from how confusing it is, and that it would put one switch doing the work of two subnets?

  Read the article

• How can I control wireless networks in Ubuntu without Network-Manager?

  - by Solignis

  Hi there, I recently installed Ubuntu on a laptop I got. I was having issues with the network manager just like I was having in my VM where it was not setting up the hostname correctly. Anyhow now I have a problem, since it is a laptop it will be moving.... But I have no way to discover new wireless networks. Anyway I can gain that functionality back? The problem I am running into is that I need to set the DNS search and domain for the machine so I can access my network but the network-manager was overriding the settings. Any help would be much appreciated.

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• How to troubleshoot slow powerconnect 62xx management interface

  - by Hannes

  Our Dell Powerconnect 62xx switches have a very high packetloss on the management interface. I presume this is caused by a new appliance which uses multicast for communication but I am not sure. Our network setup is following: servers a - Dell PC6248 | servers b - Dell PC6248 |- juniper core router servers c - Dell PC6248 | What we see is that the multicast traffic arrives at all servers (but only the servers b use the multicast) and I fear that this multicast traffic floods the switch management interface. The switches' management interfaces are reachable via vlan101, all other traffic is sent over other vlans. When I tcpdump on one of the 2 servers with a vlan 101 ip address, I only get a few arp requests but almost nothing. When I try to ping between these 2 servers, it works like a charm. I would like to know what a good way is to troubleshoot this problem and maybe help me understand what is going wrong on that subnet.

  Read the article

• Network information displayed in Linux Console

  - by Bastien974

  Hi all, I have a Fedora 10. NetworkManager is stopped. Network is configured with a static ip address. On my screen i have this : How do i disabled that network information output ? I don't see it on SSH, only the main console. Thanks !

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network.

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either The Win 7 desktop or the VM's it alwats returns a destination host unreachable. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• DHCP Relay setup in ubuntu server

  - by jerichorivera

  I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

  Read the article

• What is the difference between UDP and TCP?

  - by Guy

  My router has two protocols (and a "both" option) that I can select when setting up port forwarding: UDP and TCP. What is the difference between these two protocols and when would you select one over the other in port forwarding?

  Read the article

• DD-WRT Router Can't hold a connection after initial setup...

  - by AC

  Struggeling with my new DDWRT router (Buffalo WZR-HP-G300NH) configuration. I configured it using one machine while comparing the settings on my existing Linksys WRT54GL on another machine. To the best of my knowledge, I've set it up the same way as my Linksys, but DDWRT has so many other options. After configuring it, I plugged it into the modem, VOIP device & my network. I see the phones come back online. However after a few minutes, it seems I lose the outbound connection (phones die and I can't get out over HTTP). What's confusing me is it works for a few minutes, then it fails. No idea what to look for. Ideas?

  Read the article

• Mount linux partition as Windows network share over internet

  - by CptEO

  I have a Linux server running RHEL 6. I have two Windows servers. All servers are connected directly to the web with an external IP, they are not in a local lan. What I would like to achieve is to setup the Linux server so that it offers a single share (the whole partition) that can be mounted as network drive within Windows. I don't want to use any 3rd party software to access the linux server because I want to use the linux server as a backup for Bare Metal Restore. In order to do so, I need to be able to access the linux partition from within the Windows Recovery Enviroment where I cannot install any 3rd party software. The linux server should only be accessible from given IP addresses (e.g. the 2 windows servers). Does anyone know if the setup I would like to have is possible?

  Read the article

• Log and debug/decrypt an windows application's HTTPS traffic

  - by cweiske

  I've got a proprietary windows-only application that uses HTTPS to speak with a (also proprietary, undocumented) web service. To ultimately be able to use the web service's functionality on my linux machines, I want to reverse-engineer the web service API by analyzing the requests sent by the application. Now the question: How can I decrypt and log the HTTPS traffic? I know of several solutions which don't apply in my case: Fiddler is a man-in-the-middle HTTPS proxy which I cannot use since the application doesn't support proxies. Also, I do not (yet) know if it works with self-signed server certificates, which I doubt. Wireshark is able to decrypt SSL streams if you have the server's private certificate, which I don't have. any browser extension since the application is not a browser If I remember correctly, there have been some trojans that capture online banking information by hooking into/replacing the window's crypto API. Since the machine is mine, low level changes are possible. Maybe there is a non-trojan (white-hat) network log application out there which does the same? There is a blackhat presentation with some details available to read. They refer to Microsoft Research Detour for easy API hooking.

  Read the article

• Wireless dropouts that only affect subset of devices

  - by jwaddell

  When watching videos streamed over WiFi from a NAS box (D-Link DNS-323) I am getting wireless dropouts. However they only appear to occur when I have left my laptop (Dell Inspiron 9300 running Windows XP SP3) running; the laptop is usually suspended if I'm not using it. The dropouts have occurred when streaming to a Netgear EVA8000 streaming device, and also to a PS3. I'm using a Netgear DG834G as the wireless modem/router. When a dropout occurs I go to the laptop and see that its wireless connection has also dropped out. The odd thing is that my wife's MacBook and my iPhone still maintain their connections. What could be causing this behaviour, and how do I go about fixing it?

  Read the article

• Laptop dual ethernet?

  - by mgb

  Anyone know of a laptop with dual gigabit ethernet ports?

  Read the article

• Accesing internet with Host-Only network VirtualBox

  - by Bibo

  I have two VMs in my VirtualBox. Both are FreeBSD and should communicate between each other. I have created network with DHCP enabled and set like this: Server Address 10.10.10.1 Server Mask 255.255.255.0 Lower Address Bound 10.10.10.100 Upper Address Bound 10.10.10.200 My VMs are pinging each other and getting right ip adress. This is what I must have and can´t change. Now I want to access internet from one VM and I found that I must use two network cards but I don´t know how to set the second one. I am new with VirtualBox and this stuff so if you count with this in you answer I would appreciate that. And I have Windows 8 as host system if it´s matter.

  Read the article

< Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >