Search Results

Search found 26176 results on 1048 pages for 'stream socket client'.

Page 253/1048 | < Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >

• Hostapd to connect laptop to Android

  - by Kmegamind

  i am trying to set up my laptop as an access point for my Android to use WiFi, so i knew that ubuntu sets the network as Ad-Hoc which is not discoverable by android, So i tried the method explained here -which i found on many other websites- but when i run hostapd.conf this error appears : nl80211: Failed to set interface wlan0 into AP mode nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0x8e488f8 user_data=0x8e48ea0 handler=0x807c5e0 ELOOP: remaining socket: sock=6 eloop_data=0x8e4aca8 user_data=(nil) handler=0x8086770 this is how my hostapd.conf looks like : interface=wlan0 driver=nl80211 ssid=Any_SSID_name hw_mode=g channel=1 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=Any_password wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP and this is my wireless card info : description: Wireless interface product: BCM43225 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:73:51:f1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:f0300000-f0303fff

  Read the article

• Middle tier language for interfacing C/C++ with db and web app

  - by ggkmath

  I have a web application requiring a middle-tier language to communicate between an oracle database and math routines on a Linux server and a flex-based application on a client. I'm not a software expert, and need recommendations for which language to use for the middle-tier. The math routines are currently in Matlab but will be ported to C (or C++) as shared libraries. Thus, by default there's some C or C++ communication necessary. These routines rely on FFTW (www.fftw.org), which is called directly from C or C++ (thus, I don't see re-writing these routines in another language). The middle tier must manage traffic between the client, the math routines, and the Oracle database. The client will trigger the math routines aynchronously, and the results saved in the db and transferred back to the client, etc. The middle-tier will also need to authenticate user accounts/passwords, and send out various administrative emails. Originally I thought PhP the obvious choice, but interfacing asychronously multiple clients with the C or C++ routines doesn't seem straightforward. Then I thought, why not just keep the whole middle tier in C or C++, but I'm not sure if this is done in the industry (C or C++ doesn't seem as web-friendly as other languages). There's always Jave + JNI, but maybe that introduces other complications (not sure). Any feedback appreciated.

  Read the article

• Benefits of Server-side Coding

  There are numerous advantages to server scripting languages over client side languages in regards to creating web sites that are more compelling compared to a standard static site. Server side scripting are scripts that are executed on a web server during the compilation of data to return to a client. These scripts allow developers to modify the content that is being sent to the user prior to the return of the data to the user as well as store information about the user. In addition, server side scripts allow for a controllable environment in which they can be executed. This cannot be said for client side languages because the developer cannot control the users’ environment compared to a web server. Some users may turn off client scripts, some may be only allow limited access on the system and others may be able to gain full control of the environment.  I have been developing web applications for over 9 years, and I have used server side languages for most of the applications I have built.  Here is a list of common things I have developed with server side scripts. List of Common Generic Functionality Send Email FTP Files Security/ Access Control Encryption URL rewriting Data Access Data Creation I/O Access The one important feature server side languages will help me with on my website is Data Access because my component will be backed with a SQL server database. I believe that form validation is one instance where I might see server-side scripts and JavaScript used interchangeably because it does not matter how or where the data is validated as long as the data that gets inserted is valid. However, I would have to say that my personal experience would have to sway me in deciding what type of languages to use for form validation because they both have advantages and disadvantages based on the each situation.

  Read the article

• lots of dns requests from China, should I worry?

  - by nn4l

  I have turned on dns query logs, and when running "tail -f /var/log/syslog" I see that I get hundreds of identical requests from a single ip address: Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#10856: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#44334: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#15268: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#59597: query: mydomain.de IN ANY + The frequency is about 5 - 10 requests per second, going on for about a minute. After that the same effect repeats from a different IP address. I have now logged about 10000 requests from about 25 ip addresses within just a couple of hours, all of them come from China according to "whois [ipaddr]". What is going on here? Is my name server under attack? Can I do something about this?

  Read the article

• How would you code an AI engine to allow communication in any programming language?

  - by Tokyo Dan

  I developed a two-player iPhone board game. Computer players (AI) can either be local (in the game code) or remote running on a server. In the 2nd case, both client and server code are coded in Lua. On the server the actual AI code is separate from the TCP socket code and coroutine code (which spawns a separate instance of AI for each connecting client). I want to be able to further isolate the AI code so that that part can be a module coded by anyone in their language of choice. How can I do this? What tecniques/technology would enable communication between the Lua TCP socket/coroutine code and the AI module?

  Read the article

• OpenLDAP with StartTLS broken on Debian Lennny

  - by mr.zog

  I'm trying to get OpenLDAP on Lenny to work with StartTLS. I have a Fedora 13 machine which I'm using as a client for testing. So far the Fedora client is ignoring the 'host' directive in /etc/ldap.conf when I try to connect using ldapsearch. The client wants to connect to 127.0.0.1:389 even if I specify -H ldaps://server.name on when using ldapsearch. /etc/ldap.conf on the client machine is in mode 444. But even when I try connecting locally from an ssh session, I see errors like this: ldap_sasl_interactive_bind_s: Can't contact LDAP server (-1) Someone hit me with a cluebat, plz. Update: you must use ~/.ldaprc for settings such as 'host'.

  Read the article

• clients auto-lock feature for inactvity timeout not working

  - by Swaminathan Shanmugam

  In our sbs 2003 domain environment, the clients' pc's inactive for default period will be locked out automatically and only Ctrl+ Alt + Del & client password combination will unlock the client's pcs. Recently around 9 months before, all our client's pc's joined the new sbs 2011 but (usually all are locking with Win+L key combination manually)the auto lock feature is not working from the beginning onwards. Now only I am brought up with this issue by clients. Please help me set that option!

  Read the article

• "Directory index forbidden by Options directive" when deleting or renaming folders through webdav

  - by sandwiches

  I am trying to delete folders through webdav but all I get is 403 on the client and "Directory index forbidden by Options directive" in the Apache error log. I enabled "options indexes" for the folder and I stopped getting the errors in either the client or the log, but I still can't rename or delete folders through webdav. Any ideas why I'm unable to edit folders through webdav? I am running WAMP, default installation with Apache 2.2.17. I can connect, create files, delete files, rename them, etc. I can create folders but not delete them or rename them, once they're created. On the access log, whenever I try to delete, I get this: "DELETE /uploads/shahs HTTP/1.1" 301 243 On the error log, I get: Directory index forbidden by Options directive: The Webdav client gives a 403 when trying to delete or rename folders. Once, I added "options indexes," I stopped getting the error message in the Apache error log and the 403 on the webdav client, but now, deleting or renaming does nothing. No error messages, but nothing happens, at all.

  Read the article

• "Brute force attempt" on sending multiple emails

  - by bretddog

  While testing to send multiple emails, I successfully sent about 100 emails (with a 20KB pdf attachment), to the same email-address (my own), and they were all received. But on next attempt, my cPanel account was blocked, due to a "brute force attempt". Are there any special precautions I need to take when sending bulk emails? I simply looped through below code without pause for each email. What type of alert could that give on the email server, and how should I avoid it? client = New SmtpClient(smtp, Convert.ToInt32(port)) AddHandler client.SendCompleted, AddressOf OnAsyncSendComplete client.Credentials = New System.Net.NetworkCredential(usn, psw) client.SendAsync(mail, token) Should I wait for SendComplete event for each email before sending the next?

  Read the article

• How to attach files to an email in Windows Phone 7.5 Mango

  - by Vaibhav Garg

  In the default email client in Windows Phone 7.5 Mango, how can arbitrary files(.zip, .mp3, .txt, .pdf etc) be attached. As the storage is sand-boxed, the file handler can implement hooks to the email client, as MS-Office does and Adobe Reader doesn't, but the email client can not access files in the Phone's storage. Is there a way, or a work around? I my usage pattern, I tend to send a lot of pdfs, and am unable to do that!

  Read the article

• How to organize deployment process in Chef-controlled environment?

  - by Alex

  I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

  Read the article

• Methodology To Determine Cause Of User Specific Error

  - by user3163629

  We have software that for certain clients fails to download a file. The software is developed in Python and compiled into an Windows Executable. The cause of the error is still unknown but we have established that the client has an active internet connection. We suspect that the cause is due to the clients network setup. This error cannot be replicated in house. What technique or methodology should be applied to this kind of specific error that cannot be replicated in house. The end goal is to determine the cause of this error so we can move onto the solution. For example; Remote Debugging: Produce a debug version of the software and ask the client to send back a debug output file. This involves alot of time (back and forth communication) and requires the client to work and act in a timely manor to be successful. In-house debugging: Visit the client and determine their network setup, etc. Possibly develop a series of script tests before hand to run on the clients computer under the same network. Other methodologies and techniques I am not aware of?

  Read the article

• kill sessions for other machines

  - by LipKee

  I've an admin and client site. Multiple users will view at client site at the same time. It is possible that I can force the users logout of my client site from admin site? I'm now using classic ASP and the In Proc session is used. Is there a way where I can kill all the sessions of the users and force them to logout?

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• Mac, VNC and multiple monitors

  - by MarqueIV

  I asked a similar question here before but apparently I wasn't as clear as I had expected by the responses. That said, I'll try again. I have a Mac Pro with quad monitors which I would like to access remotely. I've been using VNC for this (either via screen sharing or a dedicated VNC client), which works, but the VNC protocol matches the physical layout/resolutions of attached monitors. One of the things I like about Microsoft's Remote Desktop (Terminal Server) client is that when you connect, it blanks out the local screens and sets the resolution to a client-specified setting. In other words, when natively running Windows, even though I'm running a physical 30" monitor flanked by 2 24" monitors as well as a 21" Cintiq monitor, I can set the Remote Desktop resolution to match my notebook's screen giving me a native, single-monitor configuration. As soon as I disconnect (and you log back in locally), the desktop un-blanks and the resolution resets back to the four physically attached monitors. Again, VNC works and yes I know I can use 5901, 5902...n to attach VNC to a specific monitor as opposed to the entire desktop, but I'm still at the mercy of trying to look at a 2560x1600 resolution on a 1280x800 screen. I'm left with either scaling (everything's too small) or panning/scrolling (it's like playing hide-and-seek with your documents!) SO... anyone know of any Mac-based remote software (client and server) that will let me connect to my Mac Pro and reset the resolution by the client, just like you can in Windows, or am I SOL?

  Read the article

• Synergy 1.3.6 on Windows 7 Test not working

  - by Joel Avery

  So I have the client running, says perfectly connected to server when I run a test I run the same test on the server and it just says "running test. press stop to end test" and no output log file comes up like on the client. Then I stop the test it says synergy is about to quot with errors and warnings. Please check the log then click OK. Except for the log didnt come up and I don't know how to access the log from command prompt. And I'm pretty sure my thing is set up correct: section: links Joel-HP: left = JoelPC2 JoelPC2: right = Joel-HP end My Windows 7 64 bit server is on the right, Windows 7 32 bit client on left Both client and server are run as admin.

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• Making Multilingual J! 1.5 + + Joomfish + VM 1.17 more workable

  - by rhand

  I have been working with a multilingual Joomla! 1.5.23 e-commerce website for a client for quite a while and made several customizations. But the client is still not happy he has to adjust content at at least three locations: Joomfish Virtuemart Article Manager Joomfish is nice in the way that it allows you to create multilingual content and copy and paste the source language on the same page, which makes translation work easier but it is annoying in the way you have to edit several custom fields at different locations/ content types. As Joomla! source language content still needs to be created in the article manager first this is the second location the client has to work at. The third location is Virtuemart. Here all the products and product categories are created. And here we added some custom fields as well. Now I was considering upgrading the website to Joomla 1.7 or later on to 1.8. This J! versions have better multilingual support. But I wonder if er can really make the client's life easier. We will still have to copy the source language to a new article and create content in another language. We will still have the issue of content in custom fields that needs to be translated and we will still have to create content. Should I go for another CMS such as Magento or do you think there is a way in a more recent Joomla! version to work with all content in one or max two locations?

  Read the article

• Which architecture should I choose for this project?

  - by Jichao

  I have a project. The server which based on a phone PCI-board is responsible for received phone calls from the customer and then redirect the phone calls to the operators. I have decided to code the server using c++ programming language and qt framework because the PCI-board SDK's interface is c/c++ originated and for the sake of portability. The server need to send the information of the the customer to the operator while ringing the operator and the ui interface of the operator client should be browser-based. Now the key problem is how could the server notify the operator that there is a phone call for he/she. One architecture I have considered is like this, The operator browser client use ajax pooling the web server to check whether there is call to the client; the web server pooling the database server to check whether there is call; the desktop server(c++) wait for the phone calls and set the information in the database. The other operations such as hang up the phone call from the client, retransfer the phone call to the other operator also use this architecture. Then, is there any way other than pooling the server(js code setInterval('getDail', 1000)) to decide whether there is a call to the operator? Is this architecture feasible or should I use some terrific techniques that I do know such as web services,xml-rpc, soap???

  Read the article

• Synergy Windows 7 Screen Saver issue

  - by SynergyUser

  I have synergy server running on a Windows 7 laptop, I have another laptop running windows XP as the Client. When synergy is first started the Screen Saver will start after the 5 mins of inactivity no problem but after mouse/keyboard input then waiting another 5 minutes + the screen saver will not come back on. The mouse is on the server NOT the client. I have tried unchecking "sync screen savers" I have tried right clicking and running the synergy server as administrator. I have tried versions 1.3.4, 1.3.6, 1.4.2 both 32 bit and 64 bit. I have tried running in XP compatibility mode. I have tried disconnecting the client. It feels like I've tried everything. The setup is as follows: The server is below the Client, the client is above the server. The server has a secondary monitor attached to it and yes I've tried running without the secondary monitor. the sever is an acer 5552G-5828. Any help would be awesome! I love synergy but without the screensavers it is annoying. Thanks!

  Read the article

• Deactivating website in ISPConfig shows another site

  - by Mattias

  A long time ago, one of our clients setup a subdomain pointing to our ip-adress. We added a website (SitesWebsiteAdd new website) that points to one of our servers. The project is now closed and the client wants us to remove the content. When we deactivate (by unclicking active) this site it automatically defaults to another website we have in our list (!?). So, because the client is still pointing to our ip, when entering project.client.com another client project is showing up by default. How is this possible? Any suggestions? I can ofcourse give you guys more details when you tell me what details you need. Thanks

  Read the article

• SSRS reports print button missing in IE 8

  - by Will Sams

  Seems like this is broken again (http://serverfault.com/questions/177268/ssrs-report-unable-to-load-client-print-control and SQL 2008 SP2 RsClientPrint ActiveX - "Unable to load client print control"). We updated all of our Windows 7 clients last Friday and it looks like the mighty "Unable to load client print control" has returned since then. Anyone aware of possible problems with the latest batch of Windows Updates?

  Read the article

• Architecture - 32-bit handling 64-bit instructions

  - by tkoomzaaskz

  tomasz@tomasz-lenovo-ideapad-Y530:~$ lscpu Architecture: i686 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 2 On-line CPU(s) list: 0,1 Thread(s) per core: 1 Core(s) per socket: 2 Socket(s): 1 Vendor ID: GenuineIntel CPU family: 6 Model: 23 Stepping: 6 CPU MHz: 2000.000 BogoMIPS: 4000.12 Cache L1d: 32K Cache L1i: 32K Cache L2: 3072K I can see that my architecture is 32-bit (i686). But CPU op-mode(s) are 32-bit and 64-bit. The question is: how come? How is it handled that a 32-bit processor performs 64-bit operations? I guess it's a lot slower than native 32-bit operations. Is it built-in processor functionality (to emulate being 64-bit) or is it software dependent? When does it make sense for a 32-bit processor to run 64-bit operations?

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• IIS FTP service - download timeouts and restarts getting the data twice

  - by accel229

  We have an IIS FTP site on a Windows Server 2003 x64 machine. Application Layer Gateway service is disabled (so http://support.microsoft.com/kb/931130 does not apply). Windows Firewall service is disabled as well. Connection timeout for the FTP site (there is only one) is set to 1,200 seconds = 20 minutes. An external client can connect to the site, list directory contents and download small files. When a client attempts to download a large file (eg, if the download continues for 3 minutes, which is still under 20 minutes, but relatively long), the server sends all data, then the connection times out, the client issues REST / RETR commands attempting to restart the download since after the last byte (which I believe should succeed and receive exactly 0 bytes), and the server behaves as if the client tried to restart after byte 0, that is, it sends the entire file all over. Any ideas on how to fix this?

  Read the article

< Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >