Search Results

Search found 9193 results on 368 pages for 'batcher sort'.

Page 262/368 | < Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• Getting at fsid under Linux? Or an alternate way of identifying filesystems?

  - by larsks

  In an environment with automounted home directories, such that the same filesystem exported by a fileserver may be mounted multiple times on the client, I would like to authoritatively be able to identify whether two mountpoints are in fact the same filesystem. That is, if the remote server exports: /home And the local client has: # mount fileserver:/home/l/lars on /home/lars type nfs (rw...) fileserver:/home/b/bob on /home/bob type nfs (rw...) I am looking for a way to identify that both /home/lars and /home/bob are in fact the same filesystem. In theory this is what the fsid result of the statvfs structure is for, but in all cases, for both local and remote filesystems, I am finding that the value of this structure member is 0. Is this some sort of client-side issue? Or do most modern NFS servers simply decline to provide a useful fsid? The end goal of all of this is to robustly interpret the output from the quota command for NFS filesystems. For example, given the example above, running quota as myself may return something like: Disk quotas for user lars (uid 6580): Filesystem blocks quota limit grace files quota limit grace otherserver:/vol/home0/a/alice 12 52428800 52428800 4 4294967295 4294967295 fileserver:/home/l/lars 9353032 9728000 10240000 124018 0 0 ...the problem here being that there exists a quota for me on otherserver which is visible in the results of the quota command, even though my home directory is actually on a different device. My plan was to look up the fsid for each mountpoint listed in the quota output and check to see if it matched the fsid associated with my home directory. It looks like this won't work, so...any suggestions?

  Read the article

• IPCop server slows down download speed

  - by noocyte

  I have an IPCop server running at home, been doing just fine for ~5 months, but last week I suddenly started getting time-outs and slow downloads from the 'net. I first thought that this was my ISP acting up, then I thought it might be one of my 3 switches or some of my cabling. In due order I've tested everything above and found them all to be working as they should. The only factor remaining is my IPCop server. Facts: I've got a 15/15 Mbit line (fiber) and I get ~15 Mbit upload, but only 0.5 Mbit download with the IPCop box as router (ISP router set in bridge mode). If I connect without the IPCop box (using the ISP router) I get ~12 Mbit upload and ~15 Mbit download. The load on the IPCop box appears to be light and it used to handle this traffic just fine 2 weeks ago. The memory usage is ~60%, I tried to restart it and test again, the memory fell to ~50% then (5 months of uptime). I'm thinking that one of my nics are busted, but I'm sort of perplexed that this could be the outcome; slow download but full speed upload. Anybody ever seen that happening before? Could it just be one of the nics that needs to be replaced? Will try that as soon as I can get my hands on a couple of new ones.

  Read the article

• Blue screen of death while installing any Adobe Air application

  - by Gaurav Sharma

  Whenever I try to install an Air application I get a Blue Screen and then my system restarts. I cannot even take a screenshot of it. This happens with every air application I try to install. I also searched for the same on Adobe forums and found the same problem being faced by someone else. His problem was resolved by uninstalling a software named "Folder Lock". I searched my hard disk for this software and found one, so I deleted that software (shift+delete) and removed all it's traces from registry too but that still doesn't solved the problem. I also tried disabling the antivirus software and then install the air application but this also didn't helped. Here is the screenshot of the BSOD. I was able to install air applications earlier, but now I can't. Anybody having same sort of problem. One colleague of mine is also having the same problem. Please help me out. My system's config is as follows: Windows XP Home sp3 Flash Builder 4, with SDK 4.1, 3.5 installed in it. Adobe Air v 2.5 1.5 GB RAM 1.66 MHz processor Thanks

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• Xbox 360 formatting for MP4 h.264?

  - by Kayle

  For the life of me, I can't get the Xbox 360 to recognize anything other than a WMV. It's full updated with Xbox Live and I even added all the Video apps (Zune, Netflix, etc) just to see if it would force some sort of codec update. I'm using handbrake, at the moment, to try and convert an mkv with subtitles. Handbrake burns the subtitles into the video for me, which is important. I can't figure out what is missing though, as the Xbox refuses to acknowledge my MP4s. Here's the VLC codec info output: As far as I can tell, this is EXACTLY what the xbox supports. I don't want to convert every video twice by throwing it through Windows Movie Maker just to get it to WMV. None of the converters mentions above output to WMV and I don't like WMV since it's not as universal as MP4. I've tried changing the container name manually to M4V, MOV, and AVI to see if I can trick the Xbox... no beans. The video displays perfectly in WMP, of course. If I convert it to WMV, suddenly it works fine. But I don't find this acceptable, as I know the Xbox is supposed to support other filetypes. If anyone knows why my Xbox won't play anything but WMVs, I would be very appreciative to know why! It's driving me nuts. The only other information I can think to include is that it's about 3 years old and of the cheapest variety (Xbox Arcade). I've added a hard drive, xbox live, and have thoroughly updated it. Maybe there's a specific video update I'm unaware of??

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• PBS batch jobs - the qalter command

  - by Ryan Budney

  I've got a giant computation running on a Scientific Linux cluster. At present I have over 600 jobs parked in the queue, waiting for processor time, while a few are running. I'm trying to use the qalter command on some of the idle but scheduled jobs. I'd like to schedule them for a later time, so that other users can jump part of the queue, sort of as an act of politeness. Is this doable? For example, JOBNAME 292399 is currently idle, scheduled to be run whenever a spot in the queue opens up. But if I run qalter -a 10051000 292398 followed by qrerun 292398 I get qrerun: Request invalid for state of job 292398.euler. From the qalter documentation, I thought 10051000 refers to tomorrow (oct 5th, 10am) but perhaps I'm misunderstanding something? If I'm going about this the wrong way, please let me know. The main thing I'm looking for is a command that's easily scriptable, so that I can modify when my queued tasks get run. qalter seems good for those purposes if I can get it working. I'd rather avoid running qdel and re qsubbing the computations, as there's a bookkeeping issue on which tasks to restart (vs which ones not to). I want to avoid that kind of bookkeeping. From googling around I notice some qalter commands have rather different date formats, but the above appears to be correct, as far as I can tell from the man docs. Any help would be appreciated.

  Read the article

• OpenVPN via DD-WRT

  - by user140491

  I am using DD-WRT with my Buffalo G300NH. I notice in my log files: Wed Oct 10 01:08:25 2012 us=343000 Cannot open /tmp/openvpn/dh.pem for DH parameters: error:02001003:system library:fopen:No such process: error:2006D080:BIO routines:BIO_new_file:no such file I have looked at other answers regarding this error. I have tried to no avail. 755 are chmod rights to /tmp/openvpn. At this point, I can not connect outside my LAN via OpenVPN. My server config looks like this: #mode server #tls-server push "route 192.168.11.1 255.255.255.0" push "dhcp-option DNS 10.8.0.1" server 10.8.0.0 255.255.255.0 port 1194 proto udp dev tun0 ifconfig 10.8.0.1 10.8.0.2 #secret /tmp/static.key ca /tmp/openvpn/ca.crt cert /tmp/openvpn/cert.pem key /tmp/openvpn/key.pem dh /tmp/openvpn/dh.pem keepalive 10 120 comp-lzo persist-key persist-tun verb 5 management localhost 5001 Can someone, knowledgeable, of this error kindly help? i have been going on several days, trying to sort it out. I like all nighters though!!

  Read the article

• Two hosting providers running simultaneously... possible / not possible? good practice / unnecessary?

  - by user29600

  For the sake of their reputation, I won't mention the names. But I'll just use: Business I worked for previously - ABC Web Dev Hosting company they used - XYZ Hosting I recently found out that XYZ Hosting had some sort of incident where they ended up losing a lot of their client's data - including ABC Web Dev's. ABC Web Dev was able to recover some of their customer's websites, after pulling them from their local development computers and putting them up on another hosting provider. They ended up losing a lot of clients because of it and their reputation ruined. I'm starting my own web dev company and I don't want to run into this same issue. I'm planning on using Rackspace but, although they are a great company, according to wikipedia they still have had downtime in their past. I thought it might be a good idea to try to run two providers at once, to ensure that if anything happened in one the websites would still be live because of the other. I know the websites would have to be pulling from one server at all times, but if there's a way to redirect requests to the second server if the first one is down that would solve my issue. As a note, we will have a staging environment setup locally which will allow for quick recovery if a provider did have any issues, however I'd like to avoid any downtime at all if possible. So my questions are: Has anyone tried running two providers simultaneously? Would this be considered good practice or am I going too far? Is there really any way to run two simultaneously where one server acts as a backup?

  Read the article

• Lenovo Wi-Fi Replacement

  - by user22910

  I recently got my T500 with a very poor signal Wi-Fi, Thinkpad BGN, a Realtek chipset. I would like to replace my Wi-Fi card with either the Intel WiFi Link 5100 or 5300. However, I read somewhere that Lenovo specfically "whitelist" their Wi-Fi cards to only work with their laptops. I could not find any of the Intel Wi-Fi, moreover any Wi-Fi cards on the Lenovo site. So, I went to hunt around in Amazon and found several sellers. Plus what sort of card do I require? There is a difference between mini cards and the full sized card, though I do not know which one my laptop supports. Here are the specifications for my laptop: http://privatepaste.com/8b0537bce0 I would like to have confirmation which one of these specific cards as posted below will work on my laptop (or the one you recommend to have): Intel Wifi Link 5300 Intel WiFi Link 5100 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft 2.0) Intel WiFi Link 5100 - Network adapter - PCI Express Half Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft) Intel WiFi Link 5300 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft)

  Read the article

• Hardware Requirements & Tuning - Flash Media Server 3.5 Interactive

  - by Anthony Kanago

  I am trying to spec out a server to purchase (physically, not rented from someone like softlayer.com) to run an intranet instace of Flash Media Server 3.5 Interactive. In general, the server will likely be fielding somewhere on the order of 400 connections at a time at the upper limit. Of course, should this increase, we don't want to be stuck. While the decision is not final, we will likely be running the server on Red Hat rather than Windows. The server will be run on gigabit ethernet. I have two related questions: What sort of hardware would I need realistically to support this? What advice can you offer for settings in tuning FMS/the OS to be performant to this level? We are looking for a bare minimum that will run this effectively to save on costs. Realistically, the average number of connections will be fairly low (50-150) by comparison with that upper limit estimate. To reiterate: we just want to be cautious in not getting caught when we need more power, but we also need a low-cost solution (doesn't everyone?) and that may take priority. Windows and RedHat are the two officially supported operating systems. Since FMS is stated to be 32-bit only, I'm sticking with a 32-bit OS. The hardware requirements listed by Adobe on their website are: 3.2GHz Intel® Pentium® 4 processor (dual Intel Xeon® or faster recommended) 2GB of RAM (4GB recommended) 1Gb Ethernet card So what realistically do I need for those sorts of connection numbers, and what can I due to tune things up to get more out of less hardware? Thanks!

  Read the article

• Memory leak in Google Chrome

  - by jasondavis

  As a developer it is very common for me to have 2-3 different IDE's open, 10-15 google chrome windows which can hold up to 200 open tabs (I know I get out of hand some times), Photoshop, couple twitter bots for promo, and a few other programs but my system still runs fast and smooth. I have an i7 processor with 12gb ram. Now with all my usual stuff running my Physical memory is usually running around 50-60% however over the course of the day or much less even, I will gradually grow to 98% The highest Memory usage processes will be from Google Chrome, if I sort in the task manager by highest memory usage and end the 1 highest process which will be a google chrome one, my memory usage will jump back down to about 60%. Also by ending that 1 process, all my Chrome windows will remain open and in use, so it doesn't affect me at all by ending that process. Based on this research I am assuming that that 1 runaway process is likely the Adobe Flash as I also can say that it gets up to the 98% much faster when I am using flash items like video or music player. But even without using any of them it will still climb up to that high number eventually. Has anyone else experienced similar results?

  Read the article

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• Computer specs for a large database

  - by SpeksETC

  What sort of computer specs (CPU, RAM, disk speed) should I use for running queries on a database of 200+ million records? The queries are for a research project, so there is only one "user" and only one query will be running at a time. I tried it on my own laptop with SQL Server with an i3 processor, 2GB RAM, 5400 RPM disk and a simple query didn't finish even after 8+ hours. I have an option to connect a SSD via eSata and upgrade to 4GB RAM, but not sure if this will be enough... Thanks! Edit: The database is about 25 GB and the indexes are not setup properly. When I tried to add an index, I let it run for about 8 hours and it still hadn't finished so I gave up. Should I have more patience :)? In general, the queries will run once in a while and its ok even if it takes a couple hours to complete.... Also, the queries will produce probably about 10 million records which I need to process using Stata/Matlab and I'm concerned that my current laptop is not strong enough, but unsure of the bottleneck....

  Read the article

• SQL Server 2008 cluster freezing

  - by Ed Leighton-Dick

  We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

  Read the article

• Write access from a Windows client via a ZFS SMB, to a file created on the host in OpenIndiana

  - by Gerald Kaszuba

  I've got an OpenIndiana server running ZFS that is shared using a nobody user and group. I don't fully understand Solaris ACL permissions, but I do know Linux style permissions. The client is Windows 8 and the server is OpenIndiana is oi_148. I'm failing to work out how to make write permission work correctly for the Windows client. It is able to make new files, but can not modify files created by the shell in OpenIndiana. When a file ("local file") is created locally as the user nobody in bash, and another file ("smb file") created remotely via SMB (as nobody also), they are quite different in permissions: # ls -V -rw-r--r-- 1 nobody nobody 0 Dec 2 12:24 local file owner@:rw-p--aARWcCos:-------:allow group@:r-----a-R-c--s:-------:allow everyone@:r-----a-R-c--s:-------:allow -rwx------+ 1 nobody nobody 0 Dec 2 12:24 smb file user:nobody:rwxpdDaARWcCos:-------:allow group:2147483648:rwxpdDaARWcCos:-------:allow In bash, I'm able to write to smb file, but vice versa, the Windows client is not able to write to local file. This is confusing to me because it appears that it should allow the SMB client to write to local file, because nobody is the owner and it has a w in the ACL. The sharesmb setting is is fairly boring, although I'm hoping there can something to set in here similar to a umask: sharesmb name=shared,guestok=true How can I make these two work together and have a symmetrical permission system, where both SMB and the local user produce the same permissions? Is there some sort of ACL that can set at the root of the file system to allow all files to be created in a similar manner?

  Read the article

• MySQL replication - rapidly growing relay bin logs

  - by Rob Forrest

  Morning all, I've got a really strange situation here this morning much like a reportedly fixed MySQL bug. http://bugs.mysql.com/bug.php?id=28421 My relay bin logs are rapidly filling with an infinite loop of junk made of this sort of thing. #121018 5:40:04 server id 101 end_log_pos 15598207 #Append_block: file_id: 2244 block_len: 8192 # at 15598352 #121018 5:40:04 server id 101 end_log_pos 15606422 #Append_block: file_id: 2244 block_len: 8192 # at 15606567 ... # at 7163731 #121018 5:38:39 server id 101 end_log_pos 7171801 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 # at 7171946 #121018 5:38:39 server id 101 end_log_pos 7180016 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 These log files grow to 1Gb within about a minute before rotating and starting again. These big files are interspersed with 1 or 2 smaller files with just this in /*!40019 SET @@session.max_insert_delayed_threads=0*/; /*!50003 SET @OLD_COMPLETION_TYPE=@@COMPLETION_TYPE,COMPLETION_TYPE=0*/; DELIMITER /*!*/; # at 4 #121023 9:43:05 server id 100 end_log_pos 106 Start: binlog v 4, server v 5.1.61-log created 121023 9:43:05 BINLOG ' mViGUA9kAAAAZgAAAGoAAAAAAAQANS4xLjYxLWxvZwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAEzgNAAgAEgAEBAQEEgAAUwAEGggAAAAICAgC '/*!*/; # at 106 #121023 9:43:05 server id 100 end_log_pos 156 Rotate to mysqld-relay-bin.000003 pos: 4 DELIMITER ; # End of log file ROLLBACK /* added by mysqlbinlog */; /*!50003 SET COMPLETION_TYPE=@OLD_COMPLETION_TYPE*/; We're running a master-master replication setup with the problematic server running mysql 5.1.61. The other server which is, for the moment, stable is running 5.1.58. Has anyone got any ideas what the solution is to this and moreover, what might have caused this?

  Read the article

• Cisco ASA: Routing packets based on where the connections started from

  - by DrStalker

  We have a Cisco ASA 5505 (version 8.2(2)) with three interfaces: outside: IP address 11.11.11.11, this is the default route inside: IP address 10.1.1.1, this is the local subnet newlink: 22.22.22.22, this is a new internet connection. We need to move VPN users from the 11.11.11.11 address to the 22.22.22.22 address, and we're using SSH on the ASA as to test and sort out the routing. The problem we have is this: If we define a particular IP as being on a static route out the newlink interface then it can SSH to 22.22.22.22 fine. If we do not define a static route then the traffic hits the ASA, but the return traffic does not come back over newlink; presumably it gets sent over the outside interfcae as that is the default route. We can't define a static route for each remote endpoint because there are dialup VPN users, who obviously change IP a lot What we need to do is configure the ASA so if a connection comes in on the newlink interface then the outgoing packets for that go over the newlink interface, not the default route. With iptables this should be do-able by marking the connection and doing mark-routing, but what is the equivalent for a Cisco ASA?

  Read the article

• Maximum RAM on Biostar P4M8PM7 Socket775 mATX board

  - by Alex Balashov

  I have a server with a Biostar P4M8PM7 ("Pro-M7") board based on a VIA chipset. It's a strange board to put in a server because it seems like more of a desktop board to me, but alas! It takes DDR2-667 (PC5300) RAM. What I can't figure out is the maximum amount I can put in it, as I cannot find the manual anywhere online. I've found a few marketing broadsheets from online retailers that say, "up to 2 GB of RAM!" but I am not sure whether to believe them. They also do not seem to be quite for the same board, as they indicate DDR2 400/533 RAM, for example: http://www.geeks.com/details.asp?invtid=P4M8P-M7. The manufacturer's web site says the same thing, but does not elaborate. It's a 64-bit CPU and board; is there a technical reason why the board would not be able to address more than 2 GB? Can someone tell me what sort of that reason that would be? I bought this server from someone really hoping I could put 8 to 16 in it, and wanted to do some research before I gave up. On a related note, it's not indicated anywhere whether it can take ECC RAM; the existing chips are not ECC, but most memory sold in the range I'm looking for (e.g. DIMMs with enough chip density to do 8 GB) seems to be server-class and for that reason ECC. Any ideas? Thank you very much for your consideration in advance!

  Read the article

• Logic behind SCCM 2012 required PXE deployments

  - by Omnomnomnom

  I'm in the process of setting up Windows 7 deployment through PXE boot, with Microsoft SCCM 2012. The imaging itself works very well, but I have a question about the logic behind PXE deployments. My setup is the following: My Windows 7 deployment task sequence is deployed to the unknown computers group. (not required, press F12 to start installing) OSDComputerName variable is also set on the unknown computers group, so unknown computers that are being imaged will prompt for a pc name. The computer then becomes known in SCCM and is added to the correct collection(s). But if I want to reïnstall windows on a known computer things are different: I can do a required deployment of the imaging task sequence to the collection of computers. Then windows installs through PXE, without any human interaction, keeping the original computer name. But because the initial deployment was not required, the "required PXE deployment" flag is not set. So as soon as I add a new computer to a collection with a required PXE deployment, it will start to reïnstall windows again. I can also deploy the imaging task sequence to the new unknown computers as required, so the flag gets set initially. But then it does not prompt for a computer name. (and it generates a name like MININT-xxx) Which is also sort of what I want. Because when i want to re-install a machine, I want it to install without interaction. How can I solve this?

  Read the article

• Trying to configure DNS on a Godaddy Virtual Dedicated host, Mediatemple Domain Registration [closed]

  - by dclowd9901

  A client of mine purchased VD hosting with Godaddy and a domain name with Mediatemple. I've never configured DNS from scratch, and I'm finding it very difficult to find any sort of explanation on how to go about it. As of right now, Mediatemple is pointing to the Godaddy's ns1.domaincontrol.com and ns2.domaincontrol.com nameservers. The VD hosting on Godaddy (via their Simple Control Panel) has options to "Add a new domain", which brings you through a wizard of sorts that asks you if the domain has already been registered (yes), what it is (dclowd9901.com for this example), create a system username and password for it (with checkboxes for SSH and FTP access), which level of user can administer it, and whether a mail account should be setup. When complete, it also creates a zone file. In this zone file, the Primary nameserver is ns1.dclowd9901.com; the records are as follow (where 12.23.12.34 is the presumed host): @ A 12.23.12.34 @ NS ns1 @ NS ns2 ns1 A 12.23.12.34 ns2 A 12.23.12.34 @ MX mail www A 12.23.12.34 ftp A 12.23.12.34 ssh A 12.23.12.34 mail A 12.23.12.34 If anyone can shed any light on this for me, explain to me the interactions between the registrar and the host and so on, I'd be very grateful. Thanks in advance for the help.

  Read the article

• Can you "swap" the Sysprep answer file in Windows 7

  - by Ben

  I have a load of new Lenovo laptops which I am due to distribute in my company. We are distributed in multiple locations and I want to ship the laptops "boxed" and untouched by IT hand for distribution. We are using LANDesk to do all the software distribution and provisioning, but are currently falling at the first hurdle as when booted, the laptops kick into the Lenovo mini-setup wizard. I assume this is because they have been sysprepped at Lenovo. In order to keep with our (almost) zero touch strategy I want the users to PXE boot into a PE of some sort, which will run a script on startup which replaces the sysprep answer file with one of my own. (i.e. prepopulated with product key, company info etc.) and then reboot to complete Sysprep. The plan is that this will run, and then install the LANDesk agent as a post-sysprep task, which in turn will complete the provisioning. Anyone have any experience / know any pitfalls to look out for / can suggest a suitable, PXE-bootable PE environment? Apologies for the verbosity of the question - it takes a bit of explaining! Thanks in advance, Ben

  Read the article

• Backing up SQL NetApp Snapshots using TSM

  - by WerkkreW

  In our environment we have a 3 node SQL 2005 Cluster which is on NetApp storage. We are currently using SMSQL (NetApp SnapManager for SQL) to take Snapshot backups of the data. This works great, but due to some audit requirements we are also forced to maintain some copies on tape. We have used NDMP in other places across the enterprise but we do not want to use it in this specific instance. Basically what I need to do is, get the most recent snapshot copy of the databases on tape, via Tivoli Storage Manager (TSM). What I have done is, obtained a basic Windows Server 2003 VM with SnapDrive installed, which is SAN attached and zoned to the NetApp, and I have written a batch file to do the following: Mount the latest __RECENT snapshot lun to the host, using a specific drive letter Perform a TSM based incremental backup Dis-mount the LUN This seems to work fine, except sometimes the LUN's do not mount due to some sort of timeout. Also, due to my limited knowledge of windows batch scripting, I have no way to monitor the success or failure of these backups since I do not know how to send a valid return code back to the TSM scheduling service. Is there a more efficient/elegant way to accomplish this without NDMP?

  Read the article

• MS SQL Server slows down over time?

  - by Dave Holland

  Have any of you experienced the following, and have you found a solution: A large part of our website's back-end is MS SQL Server 2005. Every week or two weeks the site begins running slower - and I see queries taking longer and longer to complete in SQL. I have a query that I like to use: USE master select text,wait_time,blocking_session_id AS "Block", percent_complete, * from sys.dm_exec_requests CROSS APPLY sys.dm_exec_sql_text(sql_handle) AS s2 order by start_time asc Which is fairly useful... it gives a snapshot of everything that's running right at that moment against your SQL server. What's nice is that even if your CPU is pegged at 100% for some reason and Activity Monitor is refusing to load (I'm sure some of you have been there) this query still returns and you can see what query is killing your DB. When I run this, or Activity Monitor during the times that SQL has begun to slow down I don't see any specific queries causing the issue - they are ALL running slower across the board. If I restart the MS SQL Service then everything is fine, it speeds right up - for a week or two until it happens again. Nothing that I can think of has changed, but this just started a few months ago... Ideas? --Added Please note that when this database slowdown happens it doesn't matter if we are getting 100K page views an hour (busier time of day) or 10K page views an hour (slow time) the queries all take a longer time to complete than normal. The server isn't really under stress - the CPU isn't high, the disk usage doesn't seem to be out of control... it feels like index fragmentation or something of the sort but that doesn't seem to be the case. As far as pasting results of the query I pasted above I really can't do that. The Query above lists the login of the user performing the task, the entire query, etc etc.. and I'd really not like to hand out the names of my databases, tables, columns and the logins online :)... I can tell you that the queries running at that time are normal, standard queries for our site that run all the time, nothing out of the norm.

  Read the article

< Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >