static variables - Page 264

Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

- by LaserBeak

Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

Read the article

Can connect to WAN via PC but router doesnt.

- by user16877

I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

Read the article

Binding BoundingSpheres to a world matrix in XNA

- by NDraskovic

I made a program that loads the locations of items on the scene from a file like this: using (StreamReader sr = new StreamReader(OpenFileDialog1.FileName)) { String line; while ((line = sr.ReadLine()) != null) { red = line.Split(','); model = row[0]; x = row[1]; y = row[2]; z = row[3]; elements.Add(Convert.ToInt32(model)); data.Add(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z))); sfepheres.Add(new BoundingSphere(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z)), 1f)); } I also have a list of BoundingSpheres (called spheres) that adds a new bounding sphere for each line from the file. In this program I have one item (a simple box) that moves (it has its world matrix called matrixBox), and other items are static entire time (there is a world matrix that holds those elements called simply world). The problem i that when I move the box, bounding spheres move with it. So how can I bind all BoundingSpheres (except the one corresponding to the box) to the static world matrix so that they stay in their place when the box moves?

Read the article

Good design for class with similar constructors

- by RustyTheBoyRobot

I was reading this question and thought that good points were made, but most of the solutions involved renaming one of the methods. I am refactoring some poorly written code and I've run into this situation: public class Entity { public Entity(String uniqueIdentifier, boolean isSerialNumber) { if (isSerialNumber) { this.serialNumber = uniqueIdentifier; //Lookup other data } else { this.primaryKey = uniqueIdentifier; // Lookup other data with different query } } } The obvious design flaw is that someone needed two different ways to create the object, but couldn't overload the constructor since both identifiers were of the same type (String). Thus they added a flag to differentiate. So, my question is this: when this situation arises, what are good designs for differentiating between these two ways of instantiating an object? My First Thoughts You could create two different static methods to create your object. The method names could be different. This is weak because static methods don't get inherited. You could create different objects to force the types to be different (i.e., make a PrimaryKey class and a SerialNumber class). I like this because it seems to be a better design, but it also is a pain to refactor if serialNumber is a String everywhere else.

Read the article

Managing many draw calls for dynamic objects

- by codetiger

We are developing a game (cross-platform) using Irrlicht. The game has many (around 200 - 500) dynamic objects flying around during the game. Most of these objects are static mesh and build from 20 - 50 unique Meshes. We created seperate scenenodes for each object and referring its mesh instance. But the output was very much unexpected. Menu screen: (150 tris - Just to show you the full speed rendering performance of 2 test computers) a) NVidia Quadro FX 3800 with 1GB: 1600 FPS DirectX and 2600 FPS on OpenGL b) Mac Mini with Geforce 9400M 256mb: 260 FPS in OpenGL Now inside the game in a test level: (160 dynamic objects counting around 10K tris): a) NVidia Quadro FX 3800 with 1GB: 45 FPS DirectX and 50 FPS on OpenGL b) Mac Mini with Geforce 9400M 256mb: 45 FPS in OpenGL Obviously we don't have the option of mesh batch rendering as most of the objects are dynamic. And the one big static terrain is already in single mesh buffer. To add more information, we use one 2048 png for texture for most of the dynamic objects. And our collision detection hardly and other calculations hardly make any impact on FPS. So we understood its the draw calls we make that eats up all FPS. Is there a way we can optimize the rendering, or are we missing something?

Read the article

Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

- by Lorenzo

I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

Read the article

BoundingSpheres move when they should not

- by NDraskovic

I have a XNA 4.0 project in which I load a file that contains type and coordinates of items I need to draw to the screen. Also I need to check if one particular type (the only movable one) is passing in front or trough other items. This is the code I use to load the configuration: if (ks.IsKeyDown(Microsoft.Xna.Framework.Input.Keys.L)) { this.GraphicsDevice.Clear(Color.CornflowerBlue); Otvaranje.ShowDialog(); try { using (StreamReader sr = new StreamReader(Otvaranje.FileName)) { String linija; while ((linija = sr.ReadLine()) != null) { red = linija.Split(','); model = red[0]; x = red[1]; y = red[2]; z = red[3]; elementi.Add(Convert.ToInt32(model)); podatci.Add(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z))); sfere.Add(new BoundingSphere(new Vector3(Convert.ToSingle(x), Convert.ToSingle(y), Convert.ToSingle(z)), 1f)); } } } catch (Exception ex) { Window.Title = ex.ToString(); } } The "Otvaranje" is an OpenFileDialog object, "elementi" is a List (determines the type of item that would be drawn), podatci is a List (determines the location where the items will be drawn) and sfere is a List. Now I solved the picking algorithm (checking for ray and bounding sphere intersection) and it works fine, but the collision detection does not. I noticed, while using picking, that BoundingSphere's move even though the objects that they correspond to do not. The movable object is drawn to the world1 Matrix, and the static objects are drawn into the world2 Matrix (world1 and world2 have the same values, I just separated them so that the static elements would not move when the movable one does). The problem is that when I move the item I want, all boundingSpheres move accordingly. How can I move only the boundingSphere that corresponds to that particular item, and leave the rest where they are?

Read the article

Make iMovie text overlay remain on screen after in-transition

- by Kit

My idea of a text overlay has the following timeline: In-transition Static display Out-transition For this project, I am particularly fond of iMovie's Organic Main text overlay. I want it to display for an extended period. The problem is, when I set its display time for 3:20 (minutes:seconds), it performs its transition over the whole period. The text would won't be fully seen until the next 3 minutes. This is what I want: In-transition for 1 second Static display for 3:18 minutes Out-transition for 1 second Is that possible with iMovie?

Read the article

All invalid hosts gets resolved to "com.org"

- by Vi

vi@vi-server:~$ nslookup nonexistent.itransition.com Server: 8.8.8.8 Address: 8.8.8.8#53 ** server can't find nonexistent.itransition.com: NXDOMAIN vi@vi-server:~$ cat /etc/resolv.conf nameserver 8.8.8.8 It does not exist. The same result from dig nonexistent.itransition.com. vi@vi-server:~$ ping nonexistent.itransition.com PING nonexistent.itransition.com.org (216.234.246.153) 56(84) bytes of data. 64 bytes from 99.f6.ead8.static.theplanet.com (216.234.246.153): icmp_seq=1 ttl=46 time=128 ms 64 bytes from 99.f6.ead8.static.theplanet.com (216.234.246.153): icmp_seq=2 ttl=46 time=128 ms It catches all invalid hostnames? Why? How to prevent?

Read the article

Logging Output of Azure Startup Tasks to the Event Log

- by Your DisplayName here!

This can come in handy when troubleshooting: using System; using System.Diagnostics; using System.Text; namespace Thinktecture.Azure { class Program { static EventLog _eventLog = new EventLog("Application", ".", "StartupTaskShell"); static StringBuilder _out = new StringBuilder(64); static StringBuilder _err = new StringBuilder(64); static int Main(string[] args) { if (args.Length != 1) { Console.WriteLine("Invalid arguments: " + String.Join(", ", args)); _eventLog.WriteEntry("Invalid arguments: " + String.Join(", ", args)); return -1; } var task = args[0]; ProcessStartInfo info = new ProcessStartInfo() { FileName = task, WorkingDirectory = Environment.CurrentDirectory, UseShellExecute = false, ErrorDialog = false, CreateNoWindow = true, RedirectStandardOutput = true, RedirectStandardError = true }; var process = new Process(); process.StartInfo = info; process.OutputDataReceived += (s, e) => { if (e.Data != null) { _out.AppendLine(e.Data); } }; process.ErrorDataReceived += (s, e) => { if (e.Data != null) { _err.AppendLine(e.Data); } }; process.Start(); process.BeginOutputReadLine(); process.BeginErrorReadLine(); process.WaitForExit(); var outString = _out.ToString(); var errString = _err.ToString(); if (!string.IsNullOrWhiteSpace(outString)) { outString = String.Format("Standard Out for {0}\n\n{1}", task, outString); _eventLog.WriteEntry(outString, EventLogEntryType.Information); } if (!string.IsNullOrWhiteSpace(errString)) { errString = String.Format("Standard Err for {0}\n\n{1}", task, errString); _eventLog.WriteEntry(errString, EventLogEntryType.Error); } return 0; } } } You then wrap your startup tasks with the StartupTaskShell and you’ll be able to see stdout and stderr in the application event log.

Read the article

VM clients can not access WAN

- by Saariko

I have a new VM host on my network, on a Dell R620. The dedicated iDrac is connected with static IP of: 192.168.3.x NIC #1 is connected to my router The eSXI 5.1 host is with IP of 192.168.3.250 The vSphere appliance has a static IP of 192.168.3.241 All the clients on the new host are in the same network 192.168.3.x All clients are Windows 2008 R2 My problem is that non of the clients can access the WAN. I can't ping anything which is beyond my router. I CAN ping anything within my router, even if it's on a different subnet - 192.168.0.x (Router rules are in tact and working) I can ping the gateway (192.168.3.254) One thing that I checked, and is bothering my (but don't know if it has any relevance) is that on the Host Networking properties, there is a vmnic0 (picture) that shows as if it only recognizes 192.168.0.x network - is that so? The command: route print shows me the following details, where I have a duplicate entry for 0.0.0.0 (and one is wrong) - which is probably also why it's not working

Read the article

Cached css/javascript files on Sun Java System Web Server

- by Derp

I'm doing front-end web development in a Solaris 10 / Sun Java System Web Server 7.0U2 environment. I have noticed that changes to static css or javascript files often do not take effect immediately, whereas changes to static html files always do. My best guess is that a default setting in the web server causes it to cache certain file types in order to provide reasonable performance out of the box. I don't have the admin server running--I'll need to edit the config files by hand. What change(s) can I make so that all of my css and javascript edits take effect immediately? Thanks!

Read the article

ERROR #342: DEVICE_SHADER_LINKAGE_SEMANTICNAME_NOT_FOUND

- by Telanor

I've stared at this for at least half an hour now and I cannot figure out what directx is complaining about. I know this error normally means you put float3 instead of a float4 or something like that, but I've checked over and over and as far as I can tell, everything matches. This is the full error message: D3D11: ERROR: ID3D11DeviceContext::DrawIndexed: Input Assembler - Vertex Shader linkage error: Signatures between stages are incompatible. The input stage requires Semantic/Index (COLOR,0) as input, but it is not provided by the output stage. [ EXECUTION ERROR #342: DEVICE_SHADER_LINKAGE_SEMANTICNAME_NOT_FOUND ] This is the vertex shader's input signature as seen in PIX: // Input signature: // // Name Index Mask Register SysValue Format Used // -------------------- ----- ------ -------- -------- ------ ------ // POSITION 0 xyz 0 NONE float xyz // NORMAL 0 xyz 1 NONE float // COLOR 0 xyzw 2 NONE float The HLSL structure looks like this: struct VertexShaderInput { float3 Position : POSITION0; float3 Normal : NORMAL0; float4 Color: COLOR0; }; The input layout, from PIX, is: The C# structure holding the data looks like this: [StructLayout(LayoutKind.Sequential)] public struct PositionColored { public static int SizeInBytes = Marshal.SizeOf(typeof(PositionColored)); public static InputElement[] InputElements = new[] { new InputElement("POSITION", 0, Format.R32G32B32_Float, 0), new InputElement("NORMAL", 0, Format.R32G32B32_Float, 0), new InputElement("COLOR", 0, Format.R32G32B32A32_Float, 0) }; Vector3 position; Vector3 normal; Vector4 color; #region Properties ... #endregion public PositionColored(Vector3 position, Vector3 normal, Vector4 color) { this.position = position; this.normal = normal; this.color = color; } public override string ToString() { StringBuilder sb = new StringBuilder(base.ToString()); sb.Append(" Position="); sb.Append(position); sb.Append(" Color="); sb.Append(Color); return sb.ToString(); } } SizeInBytes comes out to 40, which is correct (4*3 + 4*3 + 4*4 = 40). Can anyone find where the mistake is?

Read the article

Do I need to recompile PHP to make use of CURL API?

- by amn

I have both Apache and PHP set up manually, albeit the latter without CURL. There is this jungle of instructions and explanations on extensions for PHP. I have a very straightforward question - what do I need to do to enable CURL in a more dynamic way. I resent the idea of static linking, in fact I hate and avoid static linking like the plague. Is it possible to have my Apache and PHP understand that there is CURL in town? I can compile CURL if necessary. Package management may be out of the question, because I built PHP myself - I am on Ubuntu, and it does not provide PHP without Suhosin and a a whole lot of time, so I removed it and built PHP myself. The whole slew of related questions simply propse installing "php5-curl" package, which is exactly one thing I CANNOT do since it installs it in a completely unrelated directory, which my PHP does not even seem to bother linking to.

Read the article

Enterprise Portal Issue with the Ax Demo VPCs

- by ssmantha

Microsoft’s Ax Demo VPC is basically configured for a static IP address 192.168.0.1, this is due to the fact that the VPC has Domain Controlller configured in it which requires a static IP. When we put this VPC on a network with a different subnet and change the IP you can observer that the site http://sharepoint and http://sharepoint/EP cease to function and show “Page Not Found” errors in the browser. This is mainly due to the DNS configuration which is not updated. Below is the screen shot of the changes that needs to be done to make the site functioning properly. Change the following entries in the Forward Lookup Zones of DNS management: These websites default, SharePoint and projectserver are all mapped to a single port in the IIS i.e. port number 80. These websites are recognised with host headers. These host headers are configured in DNS with incorrect IP address entries in DNS when you change the IP address of the VPC. Just change these values to point to the Local Loop Adapter (127.0.0.1) and change the DNS to point to this address in the TCP/IP properties as shown below: This will resolve the issue with the website rendering. Initially you may get time out errors while browsing these website. be patient and try again this would work.

Read the article

Improving Windows Authentication performance on IIS

- by flalar

We're struggling with performance issues with a ASP.NET MVC site that is using Windows Authentication. Response time is very slow on the first request to the site when the user is being authenticated. Further, every time the Authorization header is sent from the browser the response time increases with many seconds. The same issue occurs for both executed files and static content like CSS and JS. Access to the application is restricted to users within a certain role and we are now planning to allow access to static files for all authenticated users to see if that helps. The authentication method in use is NTLM. How should we go forward in pinpointing why authentication decreases performance drastically?

Read the article

JAVA Gui on Hello World [closed]

- by user58892

I am designing, implementing, testing, and debuging a GUI-based version of a “Hello, World!” program in a JFrame that includes a JLabel that reads “Hello, World!” and I am trying to use a layout manager, and an Exit button to close the program. Here's what I have so far, I would really apreciate if you could help on it syntax. I am 90% done but tried hard and it couldn't run. import java.awt.*; // Needed for flow layout manager import javax.swing.*; //All swing components live in the javax.swing package import javax.swing.JButton; //to recognize buttons import javax.swing.JFrame; import javax.swing.JPanel; import javax.swing.JTextField; public class HelloWorld { public static void main(String[] args) { //creates the label. The JLabel constructor //takes an optional argument which set the text of the label /* The text will be aligned with the center of the frame * otherwise it will align on the left. */ JLabel label= new JLabel("Hello World!"); new FlowWindow(); label.setHorizontalAlignment (SwingConstants.CENTER); JFrame frame = new JFrame("Hello"); //create exit button JButton button1 = new JButton("Exit"); //Add exit button to the content pane. add(button1); frame.add(label); frame.setSize(300, 300); frame.setVisible(true); frame.setLocationRelativeTo(null); frame.toFront(); } public static void FlowWindow() { //Add a new FlowLayout()); frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); } }

Read the article

My work isn't being used... what can/ should I do?

- by Matt

Several months ago I was approached by a small business, who had seen my work previously and asked me to create a website for them. Since then, the website hasn't changed one bit and I haven't heard a word from them. This sucks for them as they paid for a website and haven't used it. It''s frustrating for me because I spent a huge amount of time on the website and feel that all of that effort has been wasted, furthermore, I don't feel I can use the website on my portfolio/ CV. I was thinking of offering to go round to their office for one day, and update the website for them then and there; but I'd need their support whilst there (to get the content for the about page, to get information for on their products etc.) and I don't want to disrupt their work day, nor do I want to sit there like a spare tyre and get nowhere. Furthermore, if I were to do this, should I expect to receive money for it? It's a day of my life, but I'm doing it for my benefit rather than theirs (but they benefit as well). Has anyone else had experience of a client not using their product; how did you handle it? Additional background for those who want it: The company is a local travel agent, and the website lets them CRUD offers and locations, and has several other static pages (about, contact, etc.) At the time of creating the website, I filled the static pages with lipsum, and the offers and locations with fake information, so that I could give the business an idea about what the final pages would look like; during the hand over, I guided them through the CRUD forms (they made notes) and said if they sent me the text for the pages, I'd update it.

Read the article

Encapsulating code in F# (Part 2)

- by MarkPearl

In part one of this series I showed an example of encapsulation within a local definition. This is useful to know so that you are aware of the scope of value holders etc. but what I am more interested in is encapsulation with regards to generating useful F# code libraries in .Net, this is done by using Namespaces and Modules. Lets have a look at some C# code first… using System; namespace EncapsulationNS { public class EncapsulationCLS { public static void TestMethod() { Console.WriteLine("Hello"); } } } Pretty simple stuff… now the F# equivalent…. namespace EncapsulationNS module EncapsulationMDL = let TestFunction = System.Console.WriteLine("Hello") () Even easier… lets look at some specifics about F# namespaces… Namespaces are open. meaning you can have multiple source files and assemblies can contribute to the same namespace. So, Namespaces are a great way to group modules together, so the question needs to be asked, what role do modules play. For me, the F# module is in many ways similar to the vb6 days of modules. In vb6 modules were separate files and simply allowed us to group certain methods together. I find it easier to visualize F# modules this way than to compare them to the C# classes. However that being said one is not restricted to one module per file – there is flexibility to have multiple modules in one code file however with my limited F# experience I would still recommend using the file as the standard level of separating modules as it is very easy to then find your way around a solution. An important note about interop with F# and other .Net languages. I wrote a blog post a while back about a very basic F# to C# interop. If I were to reference an F# library in a C# project (for instance ‘TestFunction’), in C# it would show this method as a static method call, meaning I would not have to instantiate an instance of the module.

Read the article

VirtualBox Port Forward not working when Guest IP IS specified (while doc says opposite)

- by Patrick

Trying to port forward from host (Mac OS X) 127.0.0.1:8282 - guest (CentOS)'s 10.10.10.10:8080. Existing port forwards include 127.0.0.1:8181 and 9191 to guest without any IP specified (so whatever it gets through DHCP, as explained in the documentation). Here is how the non-working binding was added: VBoxManage modifyvm "VM name" --natpf1 "rule3,tcp,127.0.0.1,8282,10.10.10.10,8080" Here is how the working ones were added: VBoxManage modifyvm "VM name" --natpf1 "rule1,tcp,127.0.0.1,8181,,80" VBoxManage modifyvm "VM name" --natpf1 "rule2,tcp,127.0.0.1,9191,,9090" And by "non-working", I of course mean not listening (as a prerequisite to forwarding): $ lsof -Pi -n|grep Virtual|grep LISTEN VirtualBo 27050 user 21u IPv4 0x2bbdc68fd363175d 0t0 TCP 127.0.0.1:9191 (LISTEN) VirtualBo 27050 user 22u IPv4 0x2bbdc68fd0e0af75 0t0 TCP 127.0.0.1:8181 (LISTEN) There should be a similar line above but with 127.0.0.1:8282. Just to be clear, this port is listening perfectly fine on the guest itself. And when I remove the guest IP (i.e., clear the 10.10.10.10) the forward works fine, albeit to eth0 (not eth1 where I need it). I can tcpdump and watch the traffic flow back and forth. And yes, I've disabled iptables entirely while testing -- it's not getting blocked anywhere on the guest. As VirtualBox writes in their documentation, you are required to specify the guest IP if it's static (makes sense, no DHCP record it keeps): "If for some reason the guest uses a static assigned IP address not leased from the built-in DHCP server, it is required to specify the guest IP when registering the forwarding rule:". However, doing so (as I need to), seems to break the port forward with nary a report in any log file I can find. (I've reviewed everything in ~/Library/VirtualBox/). Other notes: While I used the above command to add the third rule, I've also verified it showed up correctly in GUI and then removed/re-added from there just to make sure). This forum link -- while very dated -- looks somewhat related in that a port forward to a static IP was not appearing (perhaps they think due to lack of gratuitous arp being sent for host to know IP is there/avail?). Anyway, what gives? Is this still buggy? Any suggestions? If not, easy enough workarounds? What's interesting is that this works perfectly fine on another user's Mac, however he's running a slightly older version (4.3.6 v. 4.3.12).

Read the article

Kubuntu 11.10 Lot of Networking problems

- by Cobraone

Since I upgrade to 11.10 I have a lot of problems with KDE. First of all there are problems in configuring a static IP address. Just to explain @home I have a normal fiber ADSL and I use a DHCP. When I go to a customer I must insert a static IP address. With ifconfig everything seems ok but there is something wrong in searching DNS names. (I have installed Ubuntu and was going ok again). Now I Have reinstalled again Kubuntu 11.10 and I have the same problem in addition today I have discovered that if I connect to a network in another customer office the desktop freezes and I could only switch between windows with alt+tab. No FN key or right click to open run command works. So i unplugged network (configuration is just DHCP here) and tried on another position in office. It was the same. My Laptop freezes when connected, a fedora 14 of a friend works. So I decided to connect my Galaxy S II as USB network device. Everything is ok for like 3 minutes. When I noticed a little loss of signal again the desktop freezes and i must work (like now) just switching between windows with alt+tab). Additional information: Unplugging network or restarting it via Konsole does not not solve the freezing problem. Every time I must open a console and reboot. Any idea of what tests to do ? Just a recommendation: If I must post here logs or something else please guide me. I use Linux since Ubuntu 9 but I am not an "expert".

Read the article

Laptop display not working unless DVI cable is plugged in

- by marien

I have a Lenovo ThinkPad T420 with an i5 processor and integrated graphics. I dropped the laptop and now the screen is not working. I replaced the screen and it is still not working. It shows the BIOS and then at Windows login the screen gets all static looking. But if I plug in a DVI-to-HDMI cable the laptop starts and works fine. Even the external display works and the laptop display works too. As soon as I unplug the cable the screen crashes and is all static. I cannot figure out the problem. The video works because the external screen still works. How can I fix this?

Read the article

Configuring bridged network connection --- Windows 7 host, Ubuntu 10.04 guest --- VMWare Workstation 8

- by H3br3wHamm3r81

Here is my IPCONFIG /ALL from the host (Windows 7 64-bit): Here is my IFCONFIG from the guest (Ubuntu 10.04): To be honest, I don't have experience configuring a network between a host and a guest in VMWare (a virtual machine). I've searched high and low on the internet, but I haven't seen anything that can help. Perhaps I'm just not using the right keywords when I search. Nevertheless, does anyone here have any experience with establishing a network connection? Edit: One important note. I don't use DHCP to provide private addresses to the hosts on my LAN. I use "static" IP addresses on my internal network by configuring each IP address manually in the host's network configuration utility (I have TV's, XBOX 360, and a few PC's). I would like to configure the IP on the virtual machine guest manually as well. The reason is because my XBOX 360 only works properly using a static IP address. It will kick me off XBOX Live if it has one given by the router (via DHCP).

Read the article

Dependency Inversion Principle

- by Chris Paine

I have been studying also S.O.L.I.D. and watched this video: https://www.youtube.com/watch?v=huEEkx5P5Hs 01:45:30 into the video he talks about the Dependency Inversion Principle and I am scratching my head??? I had to simplify it(if possible) to get it through this thick scull of mine and here is what I came up with. Code on the marked My_modified_code my version, code marked Original DIP video version. Can I accomplish the same with the latter code? Thanks in advance. Original: namespace simple.main { class main { static void Main() { FirstClass FirstClass = new FirstClass(new OtherClass()); FirstClass.Method(); Console.ReadKey(); //tempClass temp = new OtherClass(); //temp.Method(); } } public class FirstClass { private tempClass _LastClass; public FirstClass(tempClass tempClass)//ctor { _LastClass = tempClass; } public void Method() { _LastClass.Method(); } } public abstract class tempClass{public abstract void Method();} public class LASTCLASS : tempClass { public override void Method() { Console.WriteLine("\nHello World!"); } } public class OtherClass : tempClass { public override void Method() { Console.WriteLine("\nOther World!"); } } } My_modified_code: namespace simple.main { class main { static void Main() { //FirstClass FirstClass = new FirstClass(new OtherClass()); //FirstClass.Method(); //Console.ReadKey(); tempClass temp = new OtherClass(); temp.Method(); } } //public class FirstClass //{ // private tempClass _LastClass; // public FirstClass(tempClass tempClass)//ctor // { // _LastClass = tempClass; // } // public void Method() // { // _LastClass.Method(); // } //} public abstract class tempClass{public abstract void Method();} public class LASTCLASS : tempClass { public override void Method() { Console.WriteLine("\nHello World!"); } } public class OtherClass : tempClass { public override void Method() { Console.WriteLine("\nOther World!"); } }

Read the article

Making WatiN Wait for JQuery document.Ready() Functions to Complete

- by Steve Wilkes

WatiN's DomContainer.WaitForComplete() method pauses test execution until the DOM has finished loading, but if your page has functions registered with JQuery's ready() function, you'll probably want to wait for those to finish executing before testing it. Here's a WatiN extension method which pauses test execution until that happens. JQuery (as far as I can see) doesn't provide an event or other way of being notified of when it's finished running your ready() functions, so you have to get around it another way. Luckily, because ready() executes the functions it's given in the order they're registered, you can simply register another one to add a 'marker' div to the page, and tell WatiN to wait for that div to exist. Here's the code; I added the extension method to Browser rather than DomContainer (Browser derives from DomContainer) because it's the sort of thing you only execute once for each of the pages your test loads, so Browser seemed like a good place to put it. public static void WaitForJQueryDocumentReadyFunctionsToComplete(this Browser browser) { // Don't try this is JQuery isn't defined on the page: if (bool.Parse(browser.Eval("typeof $ == 'function'"))) { const string jqueryCompleteId = "jquery-document-ready-functions-complete"; // Register a ready() function which adds a marker div to the body: browser.Eval( @"$(document).ready(function() { " + "$('body').append('<div id=""" + jqueryCompleteId + @""" />'); " + "});"); // Wait for the marker div to exist or make the test fail: browser.Div(Find.ById(jqueryCompleteId)) .WaitUntilExistsOrFail(10, "JQuery document ready functions did not complete."); } } The code uses the Eval() method to send JavaScript to the browser to be executed; first to check that JQuery actually exists on the page, then to add the new ready() method. WaitUntilExistsOrFail() is another WatiN extension method I've written (I've ended up writing really quite a lot of them) which waits for the element on which it is invoked to exist, and uses Assert.Fail() to fail the test with the given message if it doesn't exist within the specified number of seconds. Here it is: public static void WaitUntilExistsOrFail(this Element element, int timeoutInSeconds, string failureMessage) { try { element.WaitUntilExists(timeoutInSeconds); } catch (WatinTimeoutException) { Assert.Fail(failureMessage); } }

Search Results

Search found 20786 results on 832 pages for 'static variables'.

Page 264/832 | < Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271 | Next Page >

- by LaserBeak

- by user16877

- by NDraskovic

- by RustyTheBoyRobot

- by codetiger

- by Lorenzo

- by NDraskovic

- by Kit

- by Vi

- by Your DisplayName here!

- by Saariko

- by Derp

- by Telanor

- by amn

- by ssmantha

- by flalar

- by user58892

- by Matt

- by MarkPearl

- by Patrick

- by Cobraone

- by marien

- by H3br3wHamm3r81

- by Chris Paine

- by Steve Wilkes

< Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271 | Next Page >