Search Results

Search found 8056 results on 323 pages for 'external'.

Page 265/323 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

• Server 2003 and XP Client; Why are HTTP connections being silently dropped.

  - by Asa Yeamans

  On my network, my edge-router, a windows 2003 r2 server router with all the latest updates, will drop packets, but only under specific circumstances. I have troubleshot and isolated it down to the most simple configuration i can. There is NO NAT involved. Only fully-public IP addresses. No Firewalls are running either, all ahve been disabled. no packet filters on any interfaces anywhere either. I have a single Windows XP virtual machine and my edge-router(the windows 2003 r2 server, and also a virtual machine) running on a windows 2008 x64 r2 system (running virtual server 2005 as i dont have Intel-VT compatible chip yet). The edge router can access any external http site just fine, no issues. However the windows XP machine is only able to access certain sites. These work: www.google.com www.txstate.edu www.workintexas.com www.thedailywtf.com . These Dont: www.yahoo.com www.utexas.edu en.wikipedia.org slashdot.org www.bing.com. I have removed all possibility of DNS issues by connecting with net-cat from the XP box and sending GET /\r\nHost: \r\n\r\n and that connection replicates the issue as well. The network setup: My statically assigned IP block: x.x.x.168/29 DSL Modem -----PPPoE Connection---- x.x.x.169[EdgeRouter] [EdgeRouter]x.x.x.170 -----Virtual Ethernet----- x.x.x.174 [Test2] Test2's Default gateway is x.x.x.170 and test2 can ping any and every valid, accessible, public IP address with no packet loss what-so-ever. If i connect directly over PPPoE from test2 (the XP box) everything works just fine... Im at my wits end, i have NO IDEA whats causing this.

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• Completely unintuitive Apache/PHP memory-freeing behavior

  - by David

  Okay, this one's weird. I have a Turnkey Linux server with a gig of dedicated RAM. It's running WP3.2 with a boatload of plug-ins. It's a new site, so it has very limited traffic (other than search engines, maybe 20 hits a week). Now, for a few weeks, every few days, it would max out on main RAM, start eating up virtual RAM, and then crash. It's had this behavior for a while and I've been trying to figure out which element was causing the crash. Nine days ago, I pointed my external server monitor to this server. I wrote a 5-line HTML file (not PHP and not WP) that the server monitor accesses every minute, to see if the server is up. So, now, nine days later, the server has been rock solid, up all the time, no memory leak at all. I changed NOTHING on the server itself to see this behavior change. Have you EVER seen anything like this? All the server monitor is doing is retrieving a single, super-simple HTML file and all the memory leak problems have gone away. Weird, eh?

  Read the article

• Apache vhosts config: Host Name instead of IP Address

  - by Johe Green

  I have a domain (example.com) hosted at an external provider. I directed the subdomain sub.example.com to my ubuntu server (12.04 with apache2). On my ubuntu server I have a vhost setup like this. The rest of the config is basically apache 2 standard: <VirtualHost *:80> ServerName sub.example.com ServerAlias sub.example.com ServerAdmin [email protected] DocumentRoot /var/www/sub.example.com ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined WSGIScriptAlias / /home/application/sub.example.com/wsgi.py <Directory /home/application/sub.example.com> <Files wsgi.py> Order allow,deny Allow from all </Files> </Directory> </VirtualHost> When I enter http://sub.example.com in my browser my application shows up fine. But the domain is replaced by the IP address of my server. Do I have to configure my server somewhere else to deliver all its content under my domain sub.example.com?

  Read the article

• Deploy our own software using Puppet?

  - by Ken

  (Apologies in advance for the stupidity in this question. I'm normally a programmer, not a sysadmin, but I've taken it upon myself to automate some things, and clean up some other things which are automated but not in the prettiest way. :-) I've been looking around at various tools for automation of software deployment to a bunch of servers, like cfengine, Puppet, and Chef. So far, Puppet looks the most appealing, but I've certainly not committed to anything yet. These tools all look like they can do a great job of keeping a bunch of servers up-to-date with prepackaged software. What I don't get is: how does one use a tool (like Puppet) to manage deployments of our own internal software? I think I'm at a loss because I've seen a thousand tutorials showing how to keep Apache ensure => latest (which is pretty cool), but nothing that quite corresponds to my use-case today, which is something more like: when a human being pushes The Button, pull branch A from the version-control repository B run command C to compile it copy the binaries D to servers E1 through E10 on each server, run command F to make all changes take effect Puppet sounds great, and I totally see the advantage of declarative, idempotent configuration over some shell scripts, but I've not seen any tutorials for "you want to update your shell scripts to Puppet (or Chef, or cfengine) so here's what you should do". Is there such a thing? Is it obvious to other people how to take the things provided in the Puppet docs and replicate the behavior I want? Am I just not getting it? What it's sounding like to me, so far, is that the human being (#1) would manually package the software (#2 and #3) external to Puppet, manually update the Puppet config, which would trigger Puppet to update the servers ... maybe? (I'm a little confused here, as I'm sure you can tell.) Thanks!

  Read the article

• Accessing a webpage folder with .htaccess in it via apache webdav?

  - by pingo

  I have setup webdav access in order to enable an external user to upload the content of his web page to his folder on my server that is served by apache to the web. This way he could update his web page via webdav. Now the problem is that the user requires a .htaccess file and of course .htaccess breaks webdav probably because it overrides settings. (new files cannot be uploaded anymore via webdav if below specified .htaccess exists) I am running Apache2.2.17 and this is my webdav config: Alias /folderDAV "d:/wamp/www/somewebsite/" <Location /folderDAV> Order Allow,Deny Allow from all Dav On AuthType Digest AuthName DAV-upload AuthUserFile "D:/wamp/passtore/user.passwd" AuthDigestProvider file require valid-user </Location> This config is part of my naive solution to fixing this problem. The idea was to specify an alias to the web page folder where webdav would be enabled and then set AllowOverride to none so that the .htaccess would have no effect. Of course I then found out that in <Location /> AllowOverride directive is not valid. The .htaccess file looks like this: #opencart settings Options +FollowSymlinks Options -Indexes <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] ErrorDocument 403 /403.html deny from 1.1.1.1/19 allow from 2.2.2.2 What would be the solution here? I would like to have the web page accessible from the web but at the same time be able to access and modify it via apache's webdav (with digest auth). How would I do that? Also if possible I would like a solution that permits the existence of the .htaccess so that the user still has the power to setup access rules for his web page.

  Read the article

• HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

  - by Joan H.

  In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

  Read the article

• implementing NGINX loadbalancer

  - by Alaa Alomari

  I have two servers (ServerA 192.168.1.10, ServerB 192,168.1.11) and DNS of test.mysite.com is pointing to ServerA #in serverA i have this upstream lb_units { server 192.168.1.10 weight=2 max_fails=3 fail_timeout=30s; # Reverse proxy to BES1 server 192.168.1.11 weight=2 max_fails=3 fail_timeout=30s; # Reverse proxy to BES2 } server { listen 80; # Listen on the external interface server_name test.mysite.com; # The server name root /var/www/test; index index.php; location / { proxy_pass http://lb_units; # Load balance the URL location "/" to the upstream lb_units } location ~ \.php$ { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/test/$fastcgi_script_name; } } and ServerB is apache and it has the following <VirtualHost *:80 RewriteEngine on <Directory "/var/www/test" AllowOverride all </Directory DocumentRoot "/var/www/test" ServerName test.mysite.com </VirtualHost but whenever i try to browse test.mysite.com, it serves me from ServerA. also i tried to mark serverA and down server 192.168.1.10 down; in lb_units and still the same, serving me from serverA. any idea what i have done wrong??

  Read the article

• VBA Solution to VLOOKUP with Hyperlinks

  - by Emily2

  I am looking for some help with a VBA solution for preserving hyperlinks when using VLOOKUP on Excel (2010). I have a load of data on Sheet 1 for internal use only, and a cut-down version of this on Sheet 2. Instead of recreating Sheet 2 everytime, I am looking to have a working version which updates everytime Sheet1 is updated. Thus, I have used VLOOKUP on Sheet 2 so that only the desired info is returned on sheet 2. However, the problem was that sheet 1 contained in many cells Hyperlinks to external websites, and this would not pull through to Sheet2 using VLOOKUP. With some help, however, using the following VBA solution the hyperlinks now pull through: Function GetHyperLink(r As Range) As String If r.Hyperlinks.Count Then GetHyperLink = r.Hyperlinks(1).Address End If End Function And I am using the following formula in the relevant cell(s) in Sheet2: =HYPERLINK(GetHyperLink(INDEX('Sheet 1'!$B$1:$B$10001,MATCH(A4,'Sheet 1'!$A$1:$A$10001,0))),(VLOOKUP(A4,'Sheet 1'!$A$1:$B$10001,2,FALSE))) However, the problem is with formatting: every cell on Sheet2 is formatted blue and underlined, even although some of them do not contain a hyperlink! Is someone able to help with a VBA solution/formula to fix this last piece of the puzzle? Many thanks, in anticipation.

  Read the article

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• "Dictionary problem." Error with VMPlayer

  - by George Mauer

  I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

  Read the article

• Two servers, two domains, one ip. mod_proxy beginner

  - by Gutsav

  I run two virtual web servers (both running apache2 on debian). I have just one external IP, but two domains, and I want a domain going to each of the servers. I've understood that I need a Reverse Proxy, and I enabled both the mod_proxy and the mod_proxy_http modules on the "primary server". Do I need to enable anything on the "secondary server"? I also understood that I need to write some things in a virtual host file, but what? On the primary server, I have a virtual host file for one of the domains, and some for subdomains. I want domain1.tld to go to the primary server (port 80 is forwarded to it, so that works) and domain2.tld to go to the other server (internal ip 192.168.0.x). No ports needs to be forwarded to it, right? So, what to add and in which virtual host file? Or a new one? Other questions suggest adding ProxyPass and ProxyPassReverse, but I'm lost anyway, and I just don't understand the apache documentation. Thanks in advance

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• Contacts in Outlook 2003/2007, some questions

  - by Ernst

  If I create a distribution list and then select members, can I see different fields than the default ones? In 2007 there are radio buttons for 'name only' and 'more columns', but the latter does seem to only result in no results at all, regardless of which address book I choose. In 2003 there is no such thing. Is there a plug in that will break up the recipients (whether they be to, cc, or bcc) in groups of X, and send then a number of mails as required? Our host allows only 50 recipients per mail and only 300 total recipients per 5 minutes. I know the email client blat has exactly this functionality, but it does not seem to be able to connect to the exchange server to get the contacts needed. Could I maybe set outlook to send to blat which then does the breaking up as necessary? Can I (or is there a plug in for this) export only part of the contacts instead of all of them? Note that we send mail outside our organisation via our web host where we've got a few mailboxes, and we use our exchange (2000) server only internally, the few people that can send email to the outside world have an external mailbox as well as their exchange account defined. I might be able to convince our general boss that we can simply give (some) people the ability to send outside via exchange, but I might just as well not succeed. Alternatively, is there another program that can connect to exchange to get the contacts (selected based on categories) and then send via smtp in groups with delays between the mails?

  Read the article

• How NumLock is used in Ubuntu?

  - by ???

  I found that, when the NumLock is on, then many key combination won't work. For example, generally Ctrl-A is used to select all, but it won't work when NumLock is on. There are two keyboard: The laptop one (Thinkpad T61), and an external USB keyboard. The logs shown in xev: (no log when pressed Fn+NumLock on the laptop keyboard) Logs when pressed the NumLock on the USB keyboard: (Switch On) KeyPress event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187595, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False PropertyNotify event, serial 40, synthetic NO, window 0xb600001, atom 0x1b8 (XKLAVIER_STATE), time 22187601, state PropertyNewValue KeyRelease event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187723, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False (Switch Off) KeyPress event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187899, (102,107), root:(1198,133), state 0x0, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False PropertyNotify event, serial 40, synthetic NO, window 0xb600001, atom 0x1b8 (XKLAVIER_STATE), time 22187904, state PropertyNewValue KeyRelease event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22188003, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• How to access XAMPP virtual hosts from iPad on local network?

  - by martin's

  Using XAMPP on one machine. Multiple virtual hosts defined. One per project. Format is .local For example: apple.local microsoft.local client-site.local our-own-internal-site.local All works perfectly from that one machine. I now want to have other systems within the network access the various sites. The main reason for wanting to do this is to be able to test site functionality and layout from mobile devices without having to upload partial work to public servers. I can access the main XAMPP default site by simply entering the IP address of the XAMPP machine in, say, Safari on an iPad. However, there is no way to reach .local that I can see. Would this entail setting up a DNS server within the network? We have a mixture of Windows and Mac machines. No Linux. The XAMPP machine is Vista 64. I don't want real external internet access to be affected in any way, just ".local" pointed to the XAMPP machine if that makes sense.

  Read the article

• Windows Not Honoring DHCP Scope

  - by jerhinesmith

  Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

  Read the article

• Exchange 2010 certificate errors

  - by Frederik Nielsen

  I have a problem with my newly setup Exchange environment for our hosted customers. First off, when configuring the outlook client, it gives a certificate warning although the certificate has been bought and setup. I am using a setup like this: autodiscover.CUSTOMERDOMAIN.TLD CNAME autodiscover.exchange.COMPANYDOMAIN.TLD (Companydomain is our company that hosts the exchange servers, customerdomain being the customers domain) Shouldn't that work? I know that Microsoft does something like that for Office365, but I really don't think they buy a certificate for every customer.. So I guess some redirection should be setup somehow - any guidance? Next thing: When we accept that error, and move on to actually starting Outlook, it states that the certificate is not valid for the RPC proxy server exchange.COMPANYDOMAIN.TLD - this domain is not right, as that domain is not included in the certificate. I would instead like this domain to be mail.exchange.COMPANYDOMAIN.TLD I tried to run this script setting both internal and external URL's to be the same, with no luck. Any guidance on this one? I am running Exchange 2010 SP2, with CAS, HT and MBX split up on 3 different servers.

  Read the article

• how do you view / access the contents of a mounted dmg drive through TERMINAL hdiutil diskmount

  - by A. O.

  My external USB drive failed. I made a .dmg image file of the drive using disk utility. Later I was not able to mount the .dmg image. I used terminal hdiutil attach -noverify -nomount name.dmg diskutil list diskutil mountDisk /dev/disk4 then received the following message: Volume(s) mounted successfully However, I cant see the drive or access its contents through Finder. DUtility shows the drive as ghost but I still cant mount it using diskutility. Terminal tells me that the drive is mounted and constantly shows it in the diskutil list. pwd is not the mounted .dmg image. I dont know how to enter into the mounted image drive to see its contents. So in case what I said sounds like I see the files in the mounted image no this is not the case. I do not know how to access or even change the pwd within Terminal. I was hoping to see the mounted drive tru finder but I do not see that. So I need help as to how to find a way to access the mounted image drive if it was really mounted. Terminal says that it was and it shows it under diskutil list as a /dev/disk4. Can someone please help me access the files on this drive?

  Read the article

• Connecting to SVN server from a computer outside of my LAN

  - by Tom Auger

  I've got a Fedora server running Subversion and svnserve on port 3690. My repo is at /var/svn/project_name. I have my router forwarding port 3690 to the local server (as well as port 80, 21, 22 and a few others). When I connect locally to svn://192.168.0.2/project_name it works great. When I connect from an external server to svn://my.static.ip/project_name I get a time out connecting to the host. However, if I http://my.static.ip there is no problem, so port forwarding is working (at least for port 80). I don't want to run WebDAV or svn via HTTP/s. I'd like it to work using svnserve, as documented in the svn book. What have I misconfigured? EDIT Here is the last part of my iptables dump. I'm not an expert, but it looks OK to me: ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:svn ACCEPT udp -- anywhere anywhere state NEW udp dpt:svn ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:6680:6699 ACCEPT udp -- anywhere anywhere state NEW udp dpts:6680:6699 REJECT all -- anywhere anywhere reject-with icmp-host-prohibited EDIT 2 Results from sudo netstat -tulpn tcp 0 0 0.0.0.0:3690 0.0.0.0:* LISTEN 1455/svnserve

  Read the article

• Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

  - by Gleeson9

  Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

  Read the article

• What is the correct authentication mechanism when there are users inside and outside the domain?

  - by Gary Barrett

  We have a Windows 7 enterprise desktop data entry app for mobile (laptop) users with local SQL Express 2008 R2 Express db that syncs data with an SQL Server 2008 R2 Server db. Authentication is required before syncing the data. The existing group of users are part of the organisation's domain so normal scenario and they connect to the Sql Server directly. But there are plans for a second group of app users who belong to various partner organisations so they are outside our domain and have their own various separate domains/accounts. The aim is to deploy the desktop app to them and they will periodically sync data to our SQL Server. What I am uncertain of: Is it possible to authenticate users from another domain? Can permissions be managed via Active Directory etc? Which authentication protocol should be used in this scenario? Windows, Forms, SQL, etc? The IT people are requesting users of the system be managed via Active Directory. Is it possible to manage the external domain users access via Active Directory?

  Read the article

• Import data in Excel that doesn't have a row delimiter, but number of columns is known

  - by Alex B

  So i have this text file that looks something like this: Header1 Header2 Header3 Header4 A1 B1 C1 D1 A2 B2 C2 D2 and so on. When imported, I'd want the data to format itself in 4 columns. I tried the Get External Data from Text, and it successfully imports it, but it doesn't wrap it around, so it just keeps making columns for every space. I'd want it to go on the next line after 4 (in this case) elements have been added. What's the simplest way to achieve this? EDIT: My answer follows, since I'm not yet allowed to answer my own questions yet. The Excel function I needed is called indirect(). Not sure how it actually works though, so hopefully someone can help out with that, but the function call that worked for me is =INDIRECT(ADDRESS((ROW(A1)-1)*4+COLUMN(A1),1)) which i found over here: http://www.ozgrid.com/forum/showthread.php?t=101584&p=456031#post456031 Note: this required me to add the text to excel where i'd get this row full of columns, and then flip it so that i'd have a column full of rows.

  Read the article

• Diagnose remote desktop freezes in Windows 7 when no BSOD?

  - by Paul Smith

  Okay, I'm getting no joy from Asus or Microsoft on this, so hoping for some clues on how to narrow down the cause. I have very frequent OS freezes, always & only when running Remote Destkop Client (mstsc) in Windows 7 x64. I never have a bluescreen, and there is never a minidump. The display & input just freezes -- no keyboard, no mouse, and sound will just continue the last wavelength if any. So far, I can't find a way to trap the hang given that there's no bluescreen; advanced startup & recovery settings for system failure are "Write an event" checked, "Automatically restart" checked, and "Kernel memory dump". I've updated to the lasted BIOS, and tried a few different graphics drivers, both generic & ATI. I've also tried disabling Aero, and everything about the remote desktop experience (incrementally unchecked every box in the mstsc - options - experience tab), even disabled/unplugged external monitor to make sure it wasn't a dual-monitor issue. My specs are: Asus G73jh notebook 8GB RAM ATI Mobility Radeon HD 5800 Series graphics (recently tried driver versions 8.791.0.0, 8.801.0.0) American Megatrends G73jh.211 BIOS (7/27/2010) Windows 7 Home Premium x64 Windows Memory Diagnostic passed all of the following at least 3 times with no errors: MATS+ INVC LRAND Stride6 WMATS+ WINVC This notebook is better than most at removing heat (laudable vent design), so I'm not inclined to suspect thermal causes (especially since running 1080p video for hours has never caused a freeze, but mstsc does, reliably, within 5 minutes to an hour). This did seem to start happening after a Windows Update, but I've since reverted every patch applied since a week before the first occurrence, with no joy. (And I'd only had the PC for a couple weeks before that, so it could have been chance + less actual time spent remoting at the beginning.) I'm at my wits end, and I bought this laptop primarily as a remote terminal client (go figure, right?) Any ideas on how to identify the cause of this? Thanks!

  Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >