Search Results

Search found 16836 results on 674 pages for 'power management'.

Page 266/674 | < Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >

  • Lockup when unlocking screen saver

    - by chris
    I've had this happen a couple of times - screen saver kicks in, locks the screen, and when I put my password in to unlock it the system just seems to hang. Cursor turns to the busy, HDD light flickers occasionally, but the only thing I can do at that point is power down. This is on a desktop, not a laptop and according to the bios all the power saving is turned off. Has anyone else seen this? Is there a way to prevent it, or at least diagnose the cause?

    Read the article

  • Laptop not charging when connected to mains outlet

    - by Josh
    I've had this laptop for a few weeks now, it's a Sony Vaio. I went to charge it a few days ago and plugged in the power cable, but it's not charging. The battery icon in the Windows taskbar to the bottom right says it's plugged in and charging, but the charge level never goes above 2%. I have checked and I don't have a hcarging switch on the laptop anywhere, so it should be charging. If I unplug the cable, the laptop runs out of power within 30 seconds or so, further fueling my thought that it's a faulty battery. Anyone have any bright ideas? If this doesn't get fixed I'll just ring up Sony and get them to send me a replacement battery or something. Thanks.

    Read the article

  • Wake on Lan/Wan won't work after some time has passsed

    - by Vian Esterhuizen
    I have the following set up: Gigabyte Z77X-UD5H Wake On Lan Enabled Asus N66U Port Forwarding Static IP assigned to my computer Windows 7 Advanced Power Management - PCI Express - Off Intel 82579V - All options under Power Management checked I'm trying to set this up for Wake on Wan capabilities. If I shut down my computer and immediately try to Wake on Wan (and Lan) it works and starts up. While the computer is on, I've used a few WOL specific packet sniffers and the packet comes through on the correct port. After any period of time over a few minutes, waking on Wan or Lan won't work. The back "activity" light is blinking on my ethernet port on my computer, as well as on the router, so I would assume the network card is on and able to receive a signal. Any ideas? Suggestions? What can I do to troubleshoot the problem?

    Read the article

  • Sparx Enterprise Architect for SQL Server modeling?

    - by Tone
    I have used MS SQL Server Management Studio for most of my database modeling to this point in my career. I am a database developer (not a DBA), but interested in the benefits with using Sparx systems Enterprise Architect for data modeling. I do not have the need to generate scripts for different databases, other than that what does using Sparx EA buy me that SQL Management Studio does not?

    Read the article

  • Problem in SQL Server 2005

    - by megala
    I Know how to create table in SQL server 2005.But due to system problem i reinstalled SQL SErver 2005.After that I select the option like that start - programs - microsoft sql server 2005 - sql server management studio express My problem is in that sql server management studio express is not exits.How to solve the above problem Thanks in advance

    Read the article

  • working on lists in python

    - by owca
    I'm trying to make a small modification to django lfs project, that will allow me to deactivate products with no stocks. Unfortunatelly I'm just beginning to learn python, so I have big trouble with its syntax. That's what I'm trying to do. I'm using method 'has_variants' which returns true if product has any. Then I'm building a list from variants for this product. Next for every product in this list (I've called it 'set') I check it's stock and set bool variable 'inactive' to true if product has no stocks and to false if there are any. Finally if 'inactive' is false I'm setting self.active to 0. Code fails in line with: set[] = s How to correct it ? def deactivate(self): """If there are no stocks, deactivate the product. Used in last step of checkout. """ if self.has_variants(): for s in self.variants.filter(active=True): set[] = s for var in set: if var.get_stock_amount() == 0: inactive = True else: inactive = False else: if self.get_stock_amount() == 0: inactive = True if inactive: self.active = False return 0 error log : Traceback (most recent call last): File "manage.py", line 11, in <module> execute_manager(settings) File "/home/purplecow/rails/purpledev/site-packages/django/core/management/__i nit__.py", line 362, in execute_manager utility.execute() File "/home/purplecow/rails/purpledev/site-packages/django/core/management/__i nit__.py", line 303, in execute self.fetch_command(subcommand).run_from_argv(self.argv) File "/home/purplecow/rails/purpledev/site-packages/django/core/management/bas e.py", line 195, in run_from_argv self.execute(*args, **options.__dict__) File "/home/purplecow/rails/purpledev/site-packages/django/core/management/bas e.py", line 213, in execute translation.activate('en-us') File "/home/purplecow/rails/purpledev/site-packages/django/utils/translation/_ _init__.py", line 73, in activate return real_activate(language) File "/home/purplecow/rails/purpledev/site-packages/django/utils/translation/_ _init__.py", line 43, in delayed_loader return g['real_%s' % caller](*args, **kwargs) File "/home/purplecow/rails/purpledev/site-packages/django/utils/translation/t rans_real.py", line 205, in activate _active[currentThread()] = translation(language) File "/home/purplecow/rails/purpledev/site-packages/django/utils/translation/t rans_real.py", line 194, in translation default_translation = _fetch(settings.LANGUAGE_CODE) File "/home/purplecow/rails/purpledev/site-packages/django/utils/translation/t rans_real.py", line 180, in _fetch app = import_module(appname) File "/home/purplecow/rails/purpledev/site-packages/django/utils/importlib.py" , line 35, in import_module __import__(name) File "/home/purplecow/rails/purpledev/lfs/caching/__init__.py", line 1, in <mo dule> from listeners import * File "/home/purplecow/rails/purpledev/lfs/caching/listeners.py", line 10, in < module> from lfs.cart.models import Cart File "/home/purplecow/rails/purpledev/lfs/cart/models.py", line 8, in <module> from lfs.catalog.models import Product File "/home/purplecow/rails/purpledev/lfs/catalog/__init__.py", line 1, in <mo dule> from listeners import * File "/home/purplecow/rails/purpledev/lfs/catalog/listeners.py", line 5, in <m odule> from lfs.catalog.models import PropertyGroup File "/home/purplecow/rails/purpledev/lfs/catalog/models.py", line 589 set[] = s ^ SyntaxError: invalid syntax

    Read the article

  • How does operating system software maintains time clocks?

    - by Neeraj
    Hi everyone, This may sound a bit less relevant but I couldn't think of a better place to ask this question. Now consider this situation, you install an OS on your system, set the timezone and time, do some stuff and turn it off. (Note that there is no power going in to the computer). Now next time (say after some hours or days) you turn it on again, and you see the updated time. How is this possible even when my computer is not connected to the internet and was consuming no power during the period it was down.(Is there some kind of hardware hack?) please clarify!

    Read the article

  • Why Kiln is based on Mercurial, and not other (D)VCS

    - by Jakub Narebski
    What were the reason for chosing Mercurial as a basis of FogCreek Kiln, a source control management system with tightly integrated code review, and FogBugz integration? Why Mercurial, and not other (distributed) version control system, like Bazaar, Git or Monotone, or creating own version control system like Fossil (distributed software configuration management, including bug tracking and wiki) did? What were features that make FogCreek choose Mercurial as Kiln engine?

    Read the article

  • Old notebook internal display randomly not recognized

    - by jfcfar
    I have an old Acer TM4001 notebook. If the laptop is powered-off, with the lid closed, when I power it on, it generally works. Then, without touching anything, if I reboot the computer the internal display wil not work anymore. To make it working again I need to shut down the pc, close and reopen the lid and then turn it on. If I close and reopen the lid if it is not working after power the pc on, it won't work. When the screen is working, closing and opening it has no effect (the data cable seems ok). The external monitor always works as expected: If the internal display is not detected, the external will be the main (and only) display. This is not OS-related. When the screen is not working I cannot see the POST. What could be the cause for this?

    Read the article

  • Getting a black laptop screen

    - by Vivek
    I get a black screen when I boot my laptop. The laptop was in sleep mode initially, so when I pressed the power button, it looked as if it woke up from sleep mode, but the screen was blank. So, I held down the power button to force shutdown the laptop and then removed the battery. But after booting the laptop the screen still remains black. The bios/boot screen remains black as well. I have tried connecting it to external hdmi/vga/s-video devices and booting still no go. Windows loads fine, as I can type the password and get the 'Ding', then alt-f4 and shutdown windows. If it helps, the laptop model is Asus G1S-A1. Thanks in advance!

    Read the article

  • Suggestions for a SOHO/Home Asterisk system

    - by James
    I would like to buy a small embedded system that runs Linux and Asterisk. I would like two FXS ports ( to plug analogue phones into ) and one FXO port ( to plug in to my real line to allow access to the POTS ). I would like it to have a USB port to hold storage for voicemail. I really want it for home use so I would like it to be under £150 ( say $250 ), given that you can buy ADSL routers for around this much can any of them be made to run Linux and Asterisk? I don't want a PC as the power usage would be too high. I am looking for something like this ASDL router but open and able to run Asterisk or another open PBX. At worst I would like a box which had one FXO and two FXS and just made them completely available over IP to a full Asterisk system on a low power Atom system.

    Read the article

  • Output to TV only works if monitor is plugged in

    - by Greg Sansom
    I am trying to use my TV as the sole output for a computer. The computer has a graphics card with 2 outputs - one RGB and one DVI. I have the RGB output going to the TV, and when the DVI output is connected to a monitor, display works fine on both the monitor and the TV. If I turn off the monitor, or even turn off power to the monitor, the TV continues to display the desktop. If I unplug the DVI cable from the monitor (remember that the monitor doesn't have any power at this point), the TV stops presenting the desktop and displays a "Not Accepted" message. When starting up the computer, the TV displays fine, but stops working at the "press ctrl-alt-delete" screen unless the monitor is connected. How can I make the TV show the display without the monitor? The TV is an LG RT-42PZ45V. The graphics card is an ATI Radeon series HD4350 512MB GDDR2. The computer is running Windows Server 2008 r2.

    Read the article

  • Problem with intel chipset 4 serie and centos dealing with dual head

    - by Antoine
    I've a fujitsu lifebook S7220, it's been a while since i try to configure it to use a dual head with centos 5.4 x86_64. Everytime I try, the xserver crash... I've got an intel chipset mobile 4 serie (GMA 4500MHD, if I recall good!) When I do an lspci -v i've got these : 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller]) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0, IRQ 177 Memory at f2000000 (64-bit, non-prefetchable) [size=4M] Memory at d0000000 (64-bit, prefetchable) [size=256M] I/O ports at 1800 [size=8] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 3 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0 Memory at f2400000 (64-bit, non-prefetchable) [size=1M] Capabilities: [d0] Power Management version 3 My question is, anyone already got this problem and how did you fix it? Thank you for your answer!

    Read the article

  • 13-inch Macbook Pro Battery Not Charging

    - by hkhalidz
    I have a 13 inch Macbook Pro. From last night on, it says 'Battery Not Charging'. The charger's light is always green and if I remove the charger it turns off(means the battery is completely empty). I tried reseting the PRAM and SMC, but not dice. I also tried using different chargers with out any success. The Macbook Pro is from the new generations and is over a year old. The Power Information section indicates 458 for the Power Cycles. Any help would be greatly appreciated.

    Read the article

  • AMD FX 8350 potentially overheating

    - by rhughes
    I am worried that my CPU is overheating when running at maximum capacity. I have not overclocked the machine. The machine often powers down after a couple of minutes of max CPU usage. I get the following events in the Event Log after the crash: Log Name: System Source: Microsoft-Windows-Kernel-Power Date: 11/10/2013 12:05:40 Event ID: 41 Task Category: (63) Level: Critical Keywords: (2) User: SYSTEM Computer: home-pc Description: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. What can I do to confirm this or further narrow down this issue? Due to the sudden nature of the crash, no MEMORY.DMP is created I believe. I am happy to post any extra information that is needed.

    Read the article

  • High fan speed after return from suspend (on Ubuntu)

    - by Bolo
    Hi, I've got a HP ProBook 5310m laptop with Ubuntu 10.04 (32 bit). When I return from suspend, the fan speed is usually very high: FDTZ sensor reports "90 °C". Yes, the units are wrong, since FDTZ does not report temperature, but fan speed – that's probably just a small bug in reporting. Interestingly, when I plug or unplug the power cable for a moment, the fan speed returns back to normal. My questions: Where can I report this problem? Is it about ACPI support in the kernel? What is the address of the relevant bug tracker? As a workaround for now, how can I programmatically trigger a behavior equivalent to (un)plugging the power cable. More generally, how can I force ACPI to recalculate fan speed? Ideally, I'm looking for something like echo foo > /proc/bar. Thanks in advance!

    Read the article

  • The cable of my USB port hub is too short - what to do?

    - by Anna
    Hi, I just bought a new USB port hub "MSY USB 2.0 4-port hub". It has two inputs: A small USB entrance input for external power (?) The problem is that the cable that comes with the hub (small USB on one end, large USB on the other - to input into my computer), is too short for my needs. Is there a solution to this? buying a longer cable might be risky, I know that it might cause problems with power. Is there anything else I can do to make it work? Thanks.

    Read the article

  • Solution for storing sata drives outside of case

    - by Jeffrey Kevin Pry
    I have a system that has 8 sata disks in a software raid 5 array using mdadm. My issue is that I want to move the drives from inside of the computer case in order to cool more efficiently. I have looked all over the web and only seem to find enclosures that hide the drives connectors behind an estata port or some other internal raid controller. Basically what I want is an enclosure or equivalent that I can run independent sata cables to and either power as well, or have it have its own power supply. I have the sata ports on the motherboard available and don't want to limit io by using one port with a multiplier or the like. One final caveat, I am a college student on a budget and don't have a fortune to spend on such an enclosure. Thanks in advance for your help and advice.

    Read the article

  • external HDD with SATA & USB interface?

    - by Greg
    Anyone know of an external HDD that would have (in addition to USB) a SATA (eSATA) port/cable? i.e. Brand/Model. Preferably one of the name brands so I have a better change of finding it here or locally if possible. Background - In one location I want to use it is I would like to increase the performance by cabling it directly to the PC SATA port, HOWEVER I don't want to have to open up the PC to do this each time. I was thinking of running a SATA cable out through the PC case so I just plug it directly into the external HDD in question. Perhaps it should be also externally powered too so I don't need to run a power cable out from the PC power supply.

    Read the article

  • Virtual Machine files on ramdisk doesn't run faster than on physical disk

    - by Landy
    I installed total 36G memory (4x8G + 2x2G) in the host (Windows 7) and I used ImDisk to create a 32G ramdisk and format it to NTFS file system. Then I copied the virtual machine (in VMware Workstation format) folder, including vmx, vmdk, etc... to the new created ram disk. Then I tried to power on it in VMware Workstation. What made me surprised is that the performance is not better than before. It cost almost the same time to power on the Windows 7 VM. I check the Resource Monitor in the Windows 7 host, and the statistics of CPU, disk, network are rather normal. The memory has reported 3000+ hard fault/sec when guest OS boot then drop to 0 after the guest powered on. Any idea about this issue? I had thought the performance of ramdisk will be better than physical disk in this case. Am I wrong? Thanks.

    Read the article

  • Good hosted sites to manage quality testing?

    - by Chirag Patel
    Basically, I would like to manage quality testing with an issue management system focused on quality testing? I can't use the typical issue management system such as Lighthouse, FogBugz because each test is written as a ticket and 20 to 30 tickets need to be duplicated (w/ no history) every time we start a quality cycle. Do any (hosted) sites exist? We're currently using a Google Spreadsheet so it can be collaboratively edited.

    Read the article

  • Identify SATA hard drive

    - by Rob Nicholson
    Very similar question to: Physically Identify the failed hard drive But for Windows 2003 this time. Scenario: Four identical SATA hard drives plugged into motherboard (no RAID controller here) Configured as single drive in Windows as a spanned volume One of them is starting to fail with error "The driver detected a controller error on \Device\Harddisk3" How do you cross-reference Harddisk3 to the physical SATA connection on the motherboard so you know which drive to replace? I know replacing this drive will trash the spanned array requiring it to be rebuilt anyway so my rough and ready solution is: Delete the spanned partition Create individual partitions on each drive labelled E: F: G: and H: and work out which one is Harddisk3 Power down, remove each disk one at a time, power-up until the drive letter disappears But this seems a rather crude method of identifying the drive. The SATA connectors will be numbered on the motherboard but I appreciate this might not cross-match to what Windows calls them. Thanks, Rob.

    Read the article

  • Windows Home Server Passwords Do Not Match

    - by Ben Fulton
    I have a Windows Home Server that chunks along just fine most of the time. I've never bothered to put it on a UPS and so it's vulnerable to power outages that happen a few times a year. This most recent time, it came back and seemed to be fine, but whenever I try to access a shared folder I get "Passwords do not match". They matched before the power went out, and I couldn't update the WHS password since I apparently didn't know the old one. How do I fix this? (I asked this on ServerFault and they recommended it be asked here instead)

    Read the article

  • Computer not working, motherboard is suspect

    - by Arlen Beiler
    I have a problem with my computer. I have a GeForce 6100 M9 Motherboard, which I suspect is broke. The capacitors beside the CPU are corroded and the computer doesn't do anything except start the fans when I push the power button. The problem is that I can't find another motherboard as they apparently don't sell this model anymore. I have tested the Power Supply and it appears to be working. Any advice would be appreciated. Different forums have mentioned that you can replace the capacitors. Any help on this would be appreciated.

    Read the article

< Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >