Search Results

Search found 1073 results on 43 pages for 'firmware'.

Page 27/43 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• How to know which revision or router I do have?

  - by Rosamunda

  I´m trying to update my D-link Dir-600 router with the dd-wrt firmware. I´ve searched for it at the site and found that: Revision A1, B1 and B2 are supported, while C isn´t. Now my router has this information on the back: P/N IIR600GNA .... C1G H/W Ver: C1 F/W Ver: 3.01 So I guess the H/W Ver is the revision, and it´s C... so it´s a lost cause? Or maybe because it´s not just C but C1 I could do something with it? Thanks!

  Read the article

• Windows 8 to 8.1 Pro Upgrade SecureBoot Error

  - by Alexandru

  I upgraded from Windows 8 to Windows 8.1. I have an Alienware Aurora R4 with the latest BIOS firmware version, A09. Ever since I did the upgrade, I get a watermark on my desktop saying, "SecureBoot isn't configured correctly"...I would like to get rid of this watermark the correct way (not by hacking system DLLs). My BIOS shows me booting in UEFI mode, and I see that SecureBoot is actually disabled from there. I cannot enable SecureBoot, in either UEFI mode or Legacy Boot mode. Note, I can't even get Legacy Boot mode working without re-formatting my system which I really don't plan on doing, so my question is this...what has changed in the way Windows handles SecureBoot? As far as I can tell, I do not have SecureBoot enabled, and it is trying to tell me that it isn't configured correctly. Why does it even care to check if my BIOS doesn't have it on anyways?! Its so frustrating!

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Startech SVx41HDI Series Server Remote Control Usage Question - How do I switch away from a dead por

  - by tajh

  We have a Startech KVM over IP model SV841HDI and it was stuck pointing a port where the machine has been removed. We ended up having to physically plug something into that port in order to switch ports again, meaning that if someone in support accidentally switches to an empty port, we need to have a documented solution for making it useable again. The unit is old, no longer under warranty, firmware updates for it are no longer available (interestingly it runs a powerPC version of busybox). Since it does work well except for this one catch, we would like to avoid replacing it. Reading the manual, you have a several recommended methods. I tried them. Hit the left CTRL key a few times (as well as all the other popular KVM keys I could think of). The VNC GUI offers lots of buttons - none of them switch away from a dead port. The question is: how do I switch away from a dead port on this particular KVM remotely?

  Read the article

• Windows 7 on 1st Gen MacbookPro Unibody (Q4-2008) - power problems.

  - by typemismatch

  I have the first generation macbook pro, purchased Q4 2008. I've been trying to run Windows 7 and can get it all installed great with the BootCamp 3.1 64 bit drivers however ... power management isn't great. The screen and keyboard don't automatically dim - the laptop gets too hot. I noticed on some newer macbook pros that windows 7 works perfectly and the above doesn't happen. Does anyone know if there really is a hardware issue with this 1st gen or is there some firmware update I can use to fix this? Thanks!

  Read the article

• What is the formula for HughesNet FAP calculation?

  - by JohnFx

  I am somewhat frustrated with the only FAP monitor I have found on the net and discovered because it relies on a running count of bandwidth usage which (1) requires a service in the background; and (2) Tends to get inaccurate over time. Given that there is a diagnostics page on the firmware of the modem that tells the exact usage per hour, I was planning on writing a more accurate version with a better UI. However, it appears that HughesNet keeps the exact formula for calculating whether you are in FAP a secret. I have no idea why they wouldn't be more forthcoming with this information. Wondering if anyone out in SU-land had done some trial and error testing to reverse engineer the formula or had some inside knowledge to share.

  Read the article

• VPN Router + LDAP/RADIUS?

  - by MrZ

  Hello all! I need a VPN-capable router, preferably with a web interface, that should be able to authenticate against my LDAP server which is behind the router. The problem stems from the fact that I'm utterly unable to configure that setup for the Linksys RVS4000 that I own. Anything exists that is both cheap and easy to setup? Flashing the firmware is an option, as long as it is a well-documented option. Would it be viable/doable? [Edit] Okay, I've been looking at custom firmwares, any way to know which ones will work with my router before nuking its present one to oblivion? Anyone has experimented with that? My needs are quite simple, I want a DHCP router, an LDAP authenticated VPN, and basic firewall capabilities. I'm using DynDNS from the RVS4000 for now, but I guess I could setup something on the servers instead, that's only a minor problem...

  Read the article

• Can't downgrade or update jailbroken iPhone

  - by showline2

  I can't update or downgrade my iPhone 3GS, Firmware 4.3.5 tethered with redsn0w. Whenever I try to update it, I get a "device isn't eligible" error. I researched on how to do that, like changing host files, but none of them worked for me. I use OS X Snow Leopard. ## # Host Database # # localhost is used to configure the loopback interface # when the system is booting. Do not change this entry. ## 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 74.208.10.249 gs.apple.com This is my host file – not sure if it's the orginal one or not.

  Read the article

• Maximum hard drive space for an Xserve G5

  - by wjlafrance

  At my college we're upgrading an Xserve G5 (RackMac3,1) to be a file server for some courses. Currently it has one sled with a 75GB drive. Obviously, this isn't enough. I've tried some Googling on this matter and I'm hearing a ton of different stuff - custom firmware, size issues, etc. So, for anyone who knows, what's the actual lowdown on this machine. We want to put in three 2TB drives using three standard sleds, replaced with third-party drives. Is this possible?

  Read the article

• Automated VLAN creation with residential Wireless devices

  - by Zephyr Pellerin

  We've got a few WRT devices from Linksys here, and the issue has arisen to deploy them in a relatively small environment, However, in the interest of manageability we'd like to be able to automatically VLAN (ideally NOT subnet) every user from one another. It seems obvious to me that the default firmware isn't capable of this - can OpenWRT/Tomato/DD-WRT support any sort of functionality such that new users are automatically VLANed or otherwise logically separated from other users? It seems like there's an easy IPtables or PF solution here, but I've been wrong before. (If that seemed a little ambiguous, heres an example) User 1 sends DHCP request to server, new VLAN (We'll call VLAN 1) is created, user is placed in that VLAN. Then, user 2 sends a DHCP request and is placed in VLAN 2 etc. etc.

  Read the article

• Reinstall default apps on Galaxy S3 before updating to Jelly Bean [migrated]

  - by Bruno-P

  I want to update my Galaxy S3 to Jelly Bean but after downloading the firmware using Kies, it starts updating, but then it stops with a "dead" Android with a red triangle icon. I think it's because I have removed some default apps like ChatOn and Yahoo widgets. Is there any way to get them back or to install the official Jelly Bean update without a factory reset? I don't want to reinstall my apps again and lose my settings each time I need to update the OS (I also don't want bloatware apps that are pre-installed). Any ideas?

  Read the article

• Losing WLAN connections but maintaining internet connections on WIndows 7 Workgroup

  - by Di

  I have 4 computers all running Windows 7 networked in a Work group through Billion 7404vgp-m wireless router. All drivers and firmware for wireless adapters and router are up to date. Windows Firewall and Defender disabled. Disconnected ipv6. Running Nod 32 anti virus software. All have own static IP address 192.XXX.X.XXX. When I Reset the router all computers have Internet and LAN access for about 1 hour and then they will lose the LAN connection but maintain Internet connection. Resetting wireless adapters or restarting computers does nothing to fix this but resetting router will. What is causing this? How do I fix it?

  Read the article

• How to check the OS is running on bare metal and not in virtualized environment created by BIOS?

  - by Arkadi Shishlov

  Is there any software available as a Linux, *BSD, or Windows program or boot-image to check (or guess with good probability) the environment an operating system is loaded onto is genuine bare metal and not already virtualized? Given recent information from various sources, including supposed to be E.Snowden leaks, I'm curious about the security of my PC-s, even about those that don't have on-board BMC. How it could be possible and why? See for example Blue Pill, and a number of papers. With a little assistance from network card firmware, which is also loadable on popular card models, such hypervisor could easily spy on me resulting in PGP, Tor, etc. exercises futile.

  Read the article

• Can a consumer wireless router act as both a wireless client and access point?

  - by glibdud

  I'm going to be moving in the future, and integrating my home network into that of my landlord. I wish to maintain an isolated network while using his internet connection, so I'm planning on cascading my router off of his (WAN-to-LAN type configuration). Unfortunately, it looks like it might not be feasible to run a wire between the two. Therefore, I'd like to send my WAN connection over WiFi to his router. At my disposal, I have a WRT54GL (running Shibby's Tomato mod), and I just bought an Asus RT-N66U (I can be flexible with the firmware). My first thought was to set up the WRT as a wireless bridge, then run a wire between that and the N66U's WAN port. I'm reasonably sure I could make that work, but can I eliminate the WRT from the equation altogether? Can the N66U connect to the landlord's WiFi as a client, effectively using that as the WAN port, while simultaneously providing wireless access to my devices on an altogether different WLAN?

  Read the article

• Mirror network packets from WiFi to Ethernet in an ASUS Router RT N53

  - by fazineroso

  I have an ASUS RT N53 router, running the default firmware (Linux 2.6.22 with busybox and uclibc). I need to capture data packets from some Wi-Fi devices I have connected to that router (iPad and some smartphones), but the router is not forwarding any package coming from Wi-Fi devices to the Ethernet Ports. Any idea how can I proceed? Available tools in the router are iptables (no tee option, though), ebtables, brctl... Currently the ethernet and Wifi devices are forming a bridge: # brctl show bridge name bridge id STP enabled interfaces br0 8000.50465dc06be2 no vlan0 eth1 No ebtables rules: # ebtables -L Bridge table: filter Bridge chain: INPUT, entries: 0, policy: ACCEPT Bridge chain: FORWARD, entries: 0, policy: ACCEPT Bridge chain: OUTPUT, entries: 0, policy: ACCEPT

  Read the article

• How to know which revision or router I do have? [migrated]

  - by Rosamunda

  I´m trying to update my D-link Dir-600 router with the dd-wrt firmware. I´ve searched for it at the site and found that: Revision A1, B1 and B2 are supported, while C isn´t. Now my router has this information on the back: P/N IIR600GNA .... C1G H/W Ver: C1 F/W Ver: 3.01 So I guess the H/W Ver is the revision, and it´s C... so it´s a lost cause? Or maybe because it´s not just C but C1 I could do something with it? Thanks!

  Read the article

• Force RAID to read exiled disk?

  - by user198847

  user user197015 asked on 1th of November the following question: "We have a RAID 6 array (Infortrend EonStor DS S16F) that recently had two disks fail. Immediately prior to replacing these two disks, a third, good, disk was accidentally ejected from the array. After reinserting this disk it is marked as "exiled" by the array's firmware, and so even after replacing the two failed disks with new ones the array refuses to rebuild the logical volume and remains inaccessible. Since the temporarily-ejected disk is still functional and nothing has been written to the array since it was ejected, it seems that it should theoretically be possible to recover all the data on the array, but how can we convince the array to use the data from the "exiled" disk? Thanks for any help or advice you can offer." Now I've got quite the same problem. The post has been deleted by the user, so I don#t know if he was successful. Is there anybody who can help me? Thank you!

  Read the article

• How to use a D-Link usb network adapter on debian

  - by Barranka

  I have a Debian (squeeze) desktop, and I need to use a D-Link 150 USB Wireless Network Adapter. So far I've done this: $ lsusb ... Bus 001 Device 006: ID 2001:3c18 D-Link Corp. ... After looking for a solution in google, I found that I needed to install the following package: firmware-ralink_0.28+squeeze1_all.deb I've installed it, but Debian doesn't want to find the adapter. When I run lsmod, I can't find what I'm supposed to find: rt2870sta Can you point me in the right direction?

  Read the article

• Is 50% download speed on a wireless G network normal?

  - by Bartlomiej Skwira

  I have a wired connection of about 36Mb/s, but my wireless speed is max at about 18-19Mb/s. I have a WRT54G-TM (T-Mobile, 802.11G) router with DD-WRT firmware - I've upgraded it to latest build. Done some settings changes: changed channel - 13 wireless network mode - G-only ACK Timing - 0 Fragmentation Threshold and RTS Threshold - 2304 Basic Rate - All Signal/Noise ratio: -46/-94, signal quality ~50-60%. Is this normal with G networks? Edit: The AP is located about 2 meters from laptop, no walls or metal objects, but its next to a TV. I've done a channel scan (had problems locating it, go to "Status - Wireless - Site survey" - lame naming) and everybody else is on channels 1 and 6. Switched to channel 11 but it didn't help. As for trasmit power I got best results with default 71mw. The antenna might be a factor, I'm using the default 2 antennas.

  Read the article

• Macbook not connecting to WIFI

  - by Model Reject

  I have been having this problem all week. My Macbook aluminium can't see my wifi network. I have changed the channel to one that isn't being used by neighbours and my iphone picks it up straight away. In other words, the router is fine. It's just the macbook can't see it. This is driving me nuts if anyone can help... My airport card details... Card Type: AirPort Extreme (0x14E4, 0x8D) Firmware Version: Broadcom BCM43xx 1.0 (5.10.131.36.1) Locale: ETSI Supported PHY Modes: 802.11 a/b/g/n Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Wake On Wireless: Supported The funny thing is that is was intermitent on Saturday. I had to keep restarting router and it worked for about 5 minutes, now it doesn't connect or see it at all. Tried using kisMAC and it can't see network either. Thanks, C

  Read the article

• My Router is fast when i reset it but slows down seconds later

  - by hglocke

  I have a Belkin N wireless router which until recently worked perfectly fine. Now i have to reset the router every few minutes, otherwise it slows down to a crawl. What can I do? I have tried turning the routers firewall off, but it does not make any difference. As far as I'm aware there have been no recent firmware updates. EDIT: The other devices on my network (laptop and iphone) do not have this problem. I connect to the router using a TP-Link wireless network card and I have already tried uninstalling and installing the driver. Hopefully this will narrow down the problem significantly.

  Read the article

• How to edit the Boot Graphics Resource Table / Edit windows 8 BOOT LOGO?

  - by user144773

  I want to edit the screen which is displayed when windows 8 (starts) loads (/loading). As for now it has the Toshiba logo, I want my custom logo or the windows default logo. I have found that UEFI has something called "Boot Graphics Resource Table" and that it overides the default logo if there is a image present (source) How can I edit the logo stored in UEFI firmware or Boot Graphics Resource Table? if it's in the "bootres.dll", which does UEFI use? My disk (spread across a few system/usefi/windows/etc partitions) has around twenty bootres.dlls. The bootres.dll is signed by Microsoft, but I don't have to worry because I can sign the file I edit myself with my own certificate.

  Read the article

• Windows 7 - all usb devices go to sleep im idle mode

  - by dvdx

  A strange thing happened after a few updates to the system: Intel rapid storage SSD firmware update Intel Ethernet adapter update GPU Intel update When the computer turns off the screen (after 5 min), an unknown time later, all the USB devices stop working. Sound card Mouse Keybord etc. I can't turn them back on, so I can't wake up the screen or do anything except turn the computer off and back on. I checked my power save profile and all is OK there. I changed in the Device Manager, the Allow USB to sleep in all the hubs. How can I fix this??

  Read the article

• Driver proboems for SH-S203N Samsung DVD drive

  - by dircowander

  My father jsut bought me a dvd burner Samsung SH-S202N OEM and installed it into my computer. The drive seems to be able to burn media fine. But when it comes to reading dvd's, audio cd's, it just skips. It can read them it is just skipping so badly to the point where the dvd's are unwatchable and cd's skip rather bad. I am looking for the latest firmware or driver for the Samsung SH-S202N OEM. Any advice? Thanks in advance. :)

  Read the article

• Check SSD stability before returning it as broken?

  - by data_jepp

  I have the Transcend SSD 720 256GB 2,5" 7mm disk. And randomly I get disk IO in utorrent and large files copying to external will fail. I have removed it from my laptop since I need max stability. I use my laptop on exams. How can I really bench/make-it-sweat whilst connected to my desktop? I want to re-create some of the fails as I need proof if I am to return it. Firmware is updated. BIOS on laptop is updated. I could just completely nul the disk and then check for bad sectors, but is there anything else I could use for testing? Edit: It has 7 bad sector replacement operations. What does it mean?

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >