Search Results

Search found 8166 results on 327 pages for 'seven year liberal arts degree'.

Page 274/327 | < Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >

• K8NDRE motherboard in server fails to complete BIOS load with error 0078

  - by John

  K8NDRE motherboard with 4 sata drives, was running fine. Drives had raid-0 and raid-1 partitions, using mdadm. The onboard raid is disabled. Upon reformatting the drives, setting a new partition structure and new raid partitions, the bios fails to finish loading, with 0078 in the bottom right corner. Tried using completely new set of drives, and bios worked fine. Able to boot from a usb, format the drives, partition them, start raid, and then installed os. Reboot and received the same error from the bios, 0078. Works fine if I unplug the sata drives. Any thoughts? Physical inspection reveals no damage cables, connectors, or capacitors. Server was running happily for over a year, and this is the first problem it has had. Per Michael Hampton's answer: The drives, unjumpered and supporting sata III worked fine originally, and worked fine for formatting and having new partitions and raid installed on them. I did try jumpering one, with no change. If I put a brand new unformatted drive in, the motherboard recognizes it and I can proceed with formatting and installing. When I reboot, I get the 0078. I have 4 sata cables-the board supports 4 drives, so I tried each and no change. I am close to calling the motherboard done.

  Read the article

• Adding more drives to a drive array

  - by Mystere Man

  I have a friend who has two servers, a Dell 1800 and an HP 350 ML G5, both have SAS drive arrays. The Dell is a 3.5" and the HP is a 2.5". They currently only have 3 drives in each array. We want to add additional drives, but they do not appear to have caddies, just "fake" covers. I haven't been able to take a good look at them, so I'm not sure what I need to do here. Are the "sockets" just there, and I can buy additional caddies and just stick them in? Or do I have to buy some kind of caddy adapter? Also, i'm thinking of just going 2.5" in the new server, so is there a 2.5" adapter caddy that will fit in the 3.5" chassis for the Dell, so I can use 2.5" drives in the 3.5" chassis? Can I buy 6GB/s drives and add them to the 3GB/s controller? The reason is that we're going to replace both computers in a year or so, and we want to bring the drives with. So rather than buy 3GB/s drives, we just want to buy 6GB/s drives so they can be used in the new server.

  Read the article

• i7 Windows 7 laptop or Macbook Pro 15" (For making 3D model and Animation)

  - by sppdhs

  Hi everyone, I'm thinking of buying a new laptop as my current one will be 5 years old next year and it currently gives me a blue screen everytime I run a heavy software to make 3D models and animation. Question is: Should I buy Macbook Pro or a Windows 7 laptop? I tried to research and some say that Windows would be better, especially because you can buy a very high spec laptop with cheaper price. While some other say Macbook Pro is the better choice as it can run bootcamp with windows 7 100% performance on every software even though it's a mac. Is this true? Which one is actually better? Btw, the software that I usually use is 3Ds Max, Maya, and ZBrush. To note as well, I have never used a Mac before. I've checked around some stores and budget wise, I'll need around AU$3000+ to buy a Macbook pro, and AU$2000+ to buy a windows laptop. Quite a big difference in price range. Thanks in advance for your help.

  Read the article

• The BitLocker encrypted logical drive of my laptop is not accessible. On clicking error appears,"Application not found"

  - by Nauman Khan

  I had an important personal data that was stored in my laptop drive 'F'. My 4 year old son also uses my laptop to play games. To secure my data I used bitlocker software that was already there in my windows 7 ultimate 32 bit. I am using a Dell D 630 Core2Duo laptop. The thing worked fine for me and I have been able to access my data in drive 'F' as and when I required. But today, when I tried to open my 'F' drive, an error box appeared saying "Application not found". I right clicked and checked 'properties' of 'F' drive. It showed me Used Space = 0 bytes and Free Space = 0 bytes. I opened 'Disk Management' which showed my 'F' drive file system as 'Unknown (Bitlocker Encrypted). 'Disk Management' is also showing my 'F' drive as healthy logical drive. I opened 'Manage bitlocker' and found that my 'F' drive was being shown locked and 'Unlock Drive' was displayed against it, however, when i click on 'Unlock Drive', it does not function. I opened 'TPM Administration' and found an information that 'Compatible TPM cannot be found'. My bitlocker encryption was working fine which means that I had a compatible TPM in my laptop. Where has it gone? How can I enable it? Is my 'F' Drive lost forever and thus the data in there as well?

  Read the article

• using i7 "gamer" cpu in a HPC cluster

  - by user1219721

  I'm running WRF weather model. That's a ram intensive, highly parallel application. I need to build a HPC cluster for that. I use 10GB infiniband interconnect. WRF doesn't depends of core count, but on memory bandwidth. That's why a core i7 3820 or 3930K performs better than high-grade xeons E5-2600 or E7 Seems like universities uses xeon E5-2670 for WRF. It costs about $1500. Spec2006 fp_rates WRF bench shows $580 i7 3930K performs the same with 1600MHz RAM. What's interesting is that i7 can handle up to 2400MHz ram, doing a great performance increase for WRF. Then it really outperforms the xeon. Power comsumption is a bit higher, but still less than 20€ a year. Even including additional part I'll need (PSU, infiniband, case), the i7 way is still 700 €/cpu cheaper than Xeon. So, is it ok to use "gamer" hardware in a HPC cluster ? or should I do it pro with xeon ? (This is not a critical application. I can handle downtime. I think I don't need ECC?)

  Read the article

• Computer won't start after installing new video card

  - by Vercas

  So, 1 year and 340 days ago I bought a desktop computer. Since then, it has served me well. But lately, I wanted an upgrade, so I bought a new video card. I documented myself about the compatibility, and it is okay. So I opened the case, cleaned up that... dust elemental living inside of it. Unscrewed the plastic thingie on the outside to unscrew the old video card. Because of the stupid arrangement of the ports, I had to unscrew the motherboard to unplug it. So I unscrewed it, removed the old card, put in the new one, moved the motherboard back, screwed it back in, screwed the video card on the holder... thingie, and screwed the plastic thingie back in. Everything went smoothly, nothing had to be forced in/out. I connected the external power supply, closed the computer case, put the tower back in it's place and all the cables back in. When I pressed the power button, the LED turned... some color I can't distinguish. It stayed that way for a second, and then it went off. I tried a bunch of things, including permuting the external power supply arrangement (1 connection, 2 connections and no connections), with no success. And here are some of the specifications: Motherboard manufacturer: Asrock Processor: AMD Athlon II X2 3.0 GHz RAM: 2 x 2GB (had only 1 initially, bought the second plate a bit later) OLD video card: AMD Radeon HD 5450 NEW video card: Gigabyte nVidia GeForce GTX 650 GPU, 1GB GDDR5 128bit PCI-E, Dual-link DVI-Dx2 / HDMI / D-Sub Power supply: 450W + all the requirements I managed to find on the internet are met (+12V 18A or something) More specific information is stored... On that computer. If required, I may open the case again and read the stickers to find more specific information. I can also provide photos if necessary. Any ideas? Suggestions? Something? :|

  Read the article

• how to diagnose a hard system seizure? Dell+Ubuntu

  - by rob

  I've got Ubuntu 9.10 on a Dell Vostro 420 desktop, a little over a year old, which I use for plain vanilla work stuff (email, web, terminal, text editor). Every now and then, at totally random times, it completely freezes on me. Hard. Mouse and keyboard stop working, cursor stops blinking, clock stops moving. All I can do is hold down the power button on the front of the box to shut it off. Sometimes it happens after several months of continuous uptime; sometimes it happens a few minutes after a reboot, while all I've done is open a terminal to look at log files, or maybe firefox to do a google search. Each time, there is nothing at all in /var/log/messages at the time of the crash. This makes it seem like a hardware problem, and indeed a few months ago I opened the box and wiggled everything and the problem went away for a while. But now it's back. I went in and checked everything, took out each RAM card and reseated. No luck. I ran all the system diagnostics (the long version) and everything passed with flying colors. Something is messed up in this box, but without any useful logs or failed tests, how in the world am I going to find it? And of course, Dell's not gonna help me cause I went and replaced Windows with Ubuntu. What steps would you take next to track down this problem?

  Read the article

• Why did you start with Linux ? And why did you continue using it ?

  - by Stefano Borini

  I'd like to know the reasons that moved you towards Linux. Personally, I started because we had to use a Digital for the Fortran 77 exercises during my first year at the university. Linux was installed on many university computers, and I got interested in it. I always liked to code (on the C64) in basic and assembler, but I knew nothing about other languages. I soon discovered a chat engine called NUTS, and the idea of becoming proficient in C appealed me, so I started hacking the code. To do so, I needed a Unix at home, so I bought a Slackware 3.4 and installed it on my Pentium 166. I then continued using it for many years, reason being that I had pleasure in learning new things and the openness of information about the internals. It was a great learning platform. I then moved to osx because I enjoy the power of Unix with the beauty and efficiency of its interface. I am interested in your answer because I believe that the panorama has changed somehow. Although I still guess to find many "hackers" interested in Linux for the sake of knowledge, I also believe that there are other reasons (work, friends, bought a netbook).

  Read the article

• How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

  - by user31575

  Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

  Read the article

• Replacement for public folder workflow, I'm confused as to how sharepoint does it.

  - by RodH257

  For years Microsoft has been slowly phasing out public folders, perhaps exchange 2010 really is the LAST TIME they'll be shipped... I've heard sharepoint is the replacement, but I don't understand full, can someone give me an idea of how to replace this workflow? In our office, we have projects, they have a project number, ie 10353. Each job folder has a public folder, organized in a hierachy like Projects Year Folder Subfolders The main subfolder we use is for genera correspondence. When an email is received that relates to a project, it is dragged and dropped (or right click move to) a public folder. Adding public folder favourites for each user helps this. When an email is sent, we have a custom email form, which is the default email form, but with a project number field next to the subject line. When you enter the job number in there, it carbon copies our filing system in, which reads the job number and puts the email in the public folder for you. if you need to refer to emails, you go to public folder and find them there. This isn't the best with large jobs, but it works ok. Now, I have limited experience with sharepoint (well, WSS), we've used it to do some neat discussion boards/polls etc as an intranet site, but I haven't seen much of its integration with outlook. The great thing about our solution is how tightly it integrates with outlook which is exactly where the emails are. If you want to forward an old email, you go to public folder and forward it, simple. Any solution that replaces it should be at least as easy as this. Improvements we would like would be to have better searching of emails, better support in exchange (ie future version) and also, custom forms in outlook are being phased out (the VBA kind), so avoiding these would be good. Does sharepoint do this? or what solutions do this kind of thing?

  Read the article

• Display stretches 4:3 ratios; Adds scrolling to other ratios

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

  Read the article

• How does voltage fluctuation affect a laptop

  - by user45535

  I own an Acer Aspire 3680. In the past 2 years, I have given, my laptop for service due to the same kind of problem. Last year at the same time, I gave my laptop to the service center. They repaired it and I managed to ask them this question: Why does this problem happen. How can I prevent it? They said, that due to voltage fluctuations, something has gone wrong in your laptop. They actually were hesistant in mentioning as to which part they changed/repaired. Now recently the same problem happened and again I gave it to a service center to get it repaired and they also said, this is caused due to voltage fluctuation. My Question is: Due to Voltage fluctuation which part of the laptop can get affected. How can I prevent this from happening. Laptop Symptoms before I gave to service: When I plug in the adapter for charging the Green Light blinks and the laptop doesn't turn on. Neither does the charging indicator indicates the light, while charging.

  Read the article

• Clone a Windows Installation to a 3TB Hard Drive; MBR to GPT

  - by DanBlakemore

  I have Windows 7 Professional 64-bit installed on my desktop. Unfortunately for me and my wallet my hard drive is failing. I have purchased a 3TB hard drive as a replacement for my current 2TB drive. I would like to avoid as much hassle as possible in moving to this new drive so I would like to copy my current partition to the new drive using Gparted. The problem is that I suspect that my current partition is MBR, and I need GPT on my new drive since it is 3TB. Can I simply copy the MBR partition onto the new disk and then convert it to GPT after the fact (can you even convert the type of a partition)? Or would I need to somehow copy the contents of the partition into a GPT partition on the new drive? How do I go about making this transistion? Also, are there any issues I should be wary of booting to a GPT partition? If it matters, my motherboard is 1 year old as of May, 2012. Edit: My motherboard is 1 day old. My old one does not have UEFI compatibility, so I decided to make an upgrade to Intel today given that I would need a UEFI motherboard to use my new HDD. How much can I use a dying hard drive (bad sectors according to Hitachi Drive Fitness Test)? I have assumed not at all, to be safe.

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• 4.4.1 Timeout in 10 minute intervals SMTP on batch email jobs

  - by TEEKAY

  I am running a job that uses SMTP and it can run in excess of an hour, emailing the entire time. It's not my code but a workflow based app so I just get a form to configure the mail server, subj, msg, etc and can't see it's implementation. I know it is .NET and SmtpClient. I have been seeing 4.4.1 timeouts every 10 minutes being reported by the application as the response from the server. The # of emails in those 10 minute sessions are variable, between 100 and below 150 which leads me to ask about the 10 minute timeout time specifically. I have found there are several exchange properties (though I don't know what version they are running) that set timeout limits. (http://technet.microsoft.com/en-us/library/bb232205%28v=exchg.150%29.aspx) Would those values for ConnectionInactivityTimeOut and ConnectionTimeout be the controlling the timeouts? and finally I would like to ask if exchange considers the consistent connection(s) it kept receiving from the same source as one continuous connection and cause the timeout each 10 minutes and cause the timeout? I am using a static ip of the mail server. Thanks if anyone can shed any light on my problem. EDIT - It is my belief that the library is just keeping the connections around and isn't wrapped in any cleanup code or using statement. That said, I still haven't made any progress on this issue in the last year and just requeue the failed ones as I see them.

  Read the article

• DNS lookup fails when with all the MAC workstations

  - by user39564

  Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• Low-traffic WordPress website on Apache keeps crashing server

  - by OC2PS

  I have recently moved my low-moderate traffic (1000 UAUs, 5000 pageviews on a busy day) website from shared hosting to a Centos 6 64-bit VPS with Apache and cPanel running on 4 quad-core processor (likely oversold) and 3GB memory (Xen). We've had problems from the beginning. The server keeps crashing. It seems PHP keeps expanding till it consumes all the memory and crashes the server. Some folks have suggested that I should abandon Apache/cPanel/PHP/mySQL and go with nginX/Varnish/PHP-FPM/SQLite. But that's just not possible for me as I am not very tech savvy and need a simple GUI like cPanel to be able to manage the mundane management tasks (can't afford to hire system administrator or get fully managed hosting). I have come across several posts discussing optimization of Apache for WordPress. But all of these lead to articles that are pretty dated such as this ~4 year old one from Jan 2009 - http://thethemefoundry.com/blog/optimize-apache-wordpress/ The article is pretty detailed and seems helpful, but I stumble even on the first step. My httpd.conf only has 2 loadmodule commands LoadModule fastinclude_module modules/mod_fastinclude.so LoadModule bwlimited_module modules/mod_bwlimited.so So I go total bust right there. Further, my httpd.conf says Direct modifications to the Apache configuration file may be lost upon subsequent regeneration of the configuration file. To have modifications retained, all modifications must be checked into the configuration system by running: /usr/local/cpanel/bin/apache_conf_distiller I am having trouble finding where to change the modules in WHM. Please can someone help me with updated guidelines on how to optimize Apache for WordPress? Many thanks! P.S. The WordPress installation also has WP Super Cache installed. P.P.S. I also have phpBB, OpenCart, and Menalto Gallery installed.

  Read the article

• Computer not finding hard drives on boot -sometimes-

  - by todd.pund

  Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

  Read the article

• Apache2.2 not responding or logging anything on Win 7

  - by Adam

  I'm having some trouble with Apache2.2 on Windows 7. For over a year it's been running no problem, but all of a sudden requests have just stopped responding. They don't time out as such, the browser just keeps on waiting forever. Nothing is recorded in either the error log (set to debug level), the access log, or Windows' Event Log. The problem showed up when I added a new VHost and restarted, however a syntax check has shown there's no problem with the config (from the little I changed), and the service does actually start error free. I've also disabled VHosts and tried with just localhost. I've tried to telnet to the web server, and it connects, but nothing happens. The prompt just goes blank and I can't type anything, and effectively become stuck. I've ensured there's a rule within Windows Firewall for Apache, and I've even disabled the entire thing just to check it wasn't the cause. Still the same. If I stop Apache however, the request fails immediately. I've uninstalled and reinstalled Apache, in the hope it might magically fix something using the default config, but still no joy. I've tried using a different port but nothing different. Does anybody have any suggestions to fix this? Or to perhaps try and figure out either if it's Apache itself not responding or something sitting between the two that's holding things up? I'm not too savvy on debugging Windows issues like this and I've been searching for hours but not found anything of use to me. Cheers Adam

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Frequent freezes with constant disk activity on SSD netbook

  - by SamsLembas

  I am running Arch Linux on an HP Mini 1000 with a SSD. The machine is a little under a year old and fairly heavily used. About a month ago the machine started freezing up. During the freezes, the system is almost completely unresponsive, seemingly especially for disk-intensive tasks such as launching an application for the first time since reboot. The disk activity led is always constantly illuminated during the freezes. After somewhere between 30 sec and 3 minutes, the machine returns to normal operation. I am pretty sure that the SSD is the source or the problem. Iotop reports a disk transfer rate of 0 during the freezes, so I think it must be getting "stuck" and simply not performing any r/w during the time. I can't seem to find any information on these symptoms on the Internet, so any input on exactly what might be the cause of this would be greatly appreciated. The machine is under warranty, but I would rather not deal with HP until I actually know what is going on. Thanks.

  Read the article

• iCloud backup merges or overwrites?

  - by Joe McMahon

  The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• Windows - Decrypt encrypted file when user account is destroyed

  - by dc2

  I have a Virtual Machine running on my Windows Server 2008 computer that originally was received by me encryped, as the builder of the VM did it on a MAC, which decrypts files by default. I never thought to decrypt these files, as they automatically 'decrypt' when you have permission over them, so the VM has been running for over a year despite the encryption. I just upgraded my computer to Domain Controller (dcpromo.exe). Now when I try to access/run the VM, I can't because I don't have permission to decrypt the files as that was on another logon (local administrator) and now I am the domain administrator. Apparently the local admin is totally nuked when you upgrade to domain controller. I have tried EVERYTHING - taking ownership of the files, which works. Doesn't do anything for me. Adding full control to everyone on the files. I go to File Properties Advanced Details (under encryption) Users who can access this file. The only user is administrator@localcomputername, and there is a cert number. I try adding a new cert, I don't have permission. I don't have permission to: Decrypt the file (access is denied). Copy the file (to another computer) - access denied. I am totally stumped and this VM is a production machine and needs to get up right now. Does anyone have any ideas?

  Read the article

< Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >