Search Results

Search found 17847 results on 714 pages for 'virtual disk'.

Page 277/714 | < Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >

• Motherboard/PSU crippling USB and Sata

  - by celebdor

  I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

  Read the article

• Warning message in boot.ini

  - by MA1

  Hi everyone, I have a dual boot system with Windows XP Pro and Windows 7. Following are the contents of my system's boot.ini. ;Warning: Boot.ini is used on Windows XP and earlier operating systems. ;Warning: Use BCDEDIT.exe to modify Windows Vista boot options. ; [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /NOEXECUTE=OPTIN /FASTDETECT I just want to know about first two warning lines, whether these two lines are always present in dual boot system when the boot process is different for installed operating systems, for example xp + vista/w7 or windows2000 + vista/w7 etc? Regards,

  Read the article

• Rebooting Guest OS on a Hyper-V 2008 R2 Cluster results in a Shutdown

  - by S_Kuwahara

  Hi Folks, I have an interessting issue here. Sometimes when I manually reboot some of my guest OS (W2K3 / W2K8) on my Hyper-V 2008 R2 Cluster it does not reboot, it just shuts down. When I'm talking about a manual reboot, I mean connecting with RPD to the virtual server and use the shutdown funktion in the OS itself. I than have to start the virtual machine again via SCVMM / Hyper-V manager and it works just fine. There is nothing special in the eventlog of the host or guest OS. There is also nothing special logged in SCVMM. The guest OS all have the integration tools installed. Any hints? Thanks in Advance

  Read the article

• Exchange 2007 Standard Edition

  - by Phrontiste

  We Have : Exchange 2007 Standard Edition IBM System X3650 2 x Intel Xeon 5430 2.66 GHz Version 8.1 Build 240.6 Mailbox, Hub Transport, Client Access Role Installed on One Box Total Number of Mailboxes : 110 - 130 6 Physical Disks Disk 0,1 (68 GB) = Raid-1, OS Partition ( C: Partition) Disk 2,3 (279GB) = Raid-1, Exchange Database (First and Second Storage Groups) ( D: Partition ) Disk 4,5 (68 GB) = Raid-1, Exchange Transaction Logs ( E: Partition ) Setup: Storage Groups : D:\First Storage group\Mailbox database.edb Storage Groups : D:\Second Storage Group\Public Folder Database.edb Transaction Logs : E Partition Problem 1: On our D Partition (Mailbox Database Partition), total size is 279 GB, free space remaining is 64.7 GB, when I select the first storage group and second storage group folders and right click properties they report a size of 165 GB. Mailbox database reports a size of 157GB when right clicked Properties. where as the size displayed in the folder is 164,893,456 KB So, we are missing around 50-54 GB, there is nothing else on these drives, no page file, nothing at all. The partition housing the Transaction logs is reporting the sizes accurately. Any suggestions / fixes on the above ? Problem 2: As you may have already read in Problem 1, the size of the mailbox database is 157GB or 164GB reported; which is not recommended, a) What would you suggest we should do to divide mailboxes in storage groups on this same server ? b) How would we move mailboxes into different storage groups ? c) This is the information store size ? (Am I right in thinking that this is not recommended) d) Having multiple storage groups with one Mailbox DB in each, would that reduce the size of the Information Store? e) Any suggestions / how-to reduce the size of information store ? We didn't install this, we have inherited this - what other recommendations you can make in order to keep ourselves better prepared for any server disaster? We are backing up with Yosemite Backup on RD1000 (320GB) at the moment, which is backing up successfully, flushing the logs daily. We haven't done a test restore YET. I have tried to provide as much info as possible, please let me know if you need further info. Also, we haven't yet faced any problems in mailflow, access speeds, everything is working fine, we have two to five people accessing OWA or Outlook via vpn only. Thanks for your time to read the above - will look forward to your expert suggestions.

  Read the article

• Memory cache Ubuntu 9.10 server x86 doesn't work as expected

  - by Matthijs

  We're using an Ubuntu 9.10 server to transfer Ghost-image files. We configured it only with Samba. And the DOS-clients connect to Samba. The latest updates are installed and so far the servers is running fine. When we image 10 pc's with the same image of 2 files of 2GB there's no disk activity. Everything is loaded in the RAM. There's 4GB in the server. But when we use 2 pc's with 2 different image files of 500 MB (8x) files then there's a lot of continuous disk activity. The speed is lower. So it seems that Ubuntu doesn't cache more then one big file. Are there settings to change this behaviour?

  Read the article

• Volume group disappeared, LVs still available

  - by Ben

  I've run into an issue with my KVM host which runs VMs on a LVM volume. As of last night the logical volumes are no longer seen as such (I can't create snapshots of them even though I have been for months now). Running any scans all result in nothing being found: [root@apollo ~]# pvscan No matching physical volumes found [root@apollo ~]# vgscan Reading all physical volumes. This may take a while... No volume groups found root@apollo ~]# lvscan No volume groups found If I try restoring the VG conf backup from /etc/lvm/backups/vg0 I get the following error: [root@apollo ~]# vgcfgrestore -f /etc/lvm/backup/vg0 vg0 Couldn't find device with uuid 20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt. Cannot restore Volume Group vg0 with 1 PVs marked as missing. Restore failed. /etc/lvm/backups/vg0 has the following for the physical volume: physical_volumes { pv0 { id = "20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt" device = "/dev/sda5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 4292870143 # 1.99902 Terabytes pe_start = 384 pe_count = 524031 # 1.99902 Terabytes } } fdisk -l /dev/sda shows the following: [root@apollo ~]# fdisk -l /dev/sda Disk /dev/sda: 6000.1 GB, 6000069312512 bytes 64 heads, 32 sectors/track, 5722112 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000188b7 Device Boot Start End Blocks Id System /dev/sda1 2 32768 33553408 82 Linux swap / Solaris /dev/sda2 32769 33280 524288 83 Linux /dev/sda3 33281 1081856 1073741824 83 Linux /dev/sda4 1081857 3177984 2146435072 85 Linux extended /dev/sda5 1081857 3177984 2146435071+ 8e Linux LVM The server is running a 4 disk HW RAID10 which seems perfectly healthy according to megacli and smartd. The only odd message in /var/log/messages is the following which shows up every couple of hours: Jun 10 09:41:57 apollo udevd[527]: failed to create queue file: No space left on device Output of df -h [root@apollo ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1016G 119G 847G 13% / /dev/sda2 508M 67M 416M 14% /boot Does anyone have any ideas what to do next? The VMs are all running fine at the moment apart from not being able to snapshot them. Updated with extra info It's not a lack of inodes: [root@apollo ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 67108864 48066 67060798 1% / /dev/sda2 32768 47 32721 1% /boot pvs, vgs & lvs either output nothing or "No volume groups found".

  Read the article

• STOP: c000021a {Fatal System Error} The initial session process or system process terminated unexpectedly

  - by christof

  I'm encountering such an error after expanding disk space on a virtual machine using Hyper-V. STOP: c000021a {Fatal System Error} The initial session process or system process terminated unexpectedly with a status of (0x00000000) (0xc000012d 0x001003f0). The virtual server there is Windows Server 2008 R2 Enterprise Edition, which is also Domain Controller. I've tried to repair Windows but there is no restore point, and using the command line. I've tried the sfc /SCANNOW /OFFBOOTDIR /OFFWINDIR command, but I got the error Windows Resource Protection could not perform the requested operation.

  Read the article

• How can I compact the VHD file with Ubuntu?

  - by AmShegar

  I use windows server 2008r2 with role Hyper-V. The guest system is Ubuntu 12.04 LTC. It is situated on the dynamic virtual hard disk. I want to compact this VHD (The real size is 50 GB, 360 GB on the disk). But I can not do this, because the Ubuntu file system is not NTFS. What do I need (gparted, sdelete, ...) for solving this problem? The main problem is that the filesystem is not NTFS, but ext4.

  Read the article

• What does this IIS memory dump mean? (reserved memory)

  - by Jesse

  My w3wp's are recycling every 60 seconds after using too much virtual memory. I ran the IIS Debug Diagnostic Tool to capture a memory dump before the worker process recycled; the most interesting part seems to be this: Virtual Allocation Summary Reserved memory 4.88 GBytes Committed memory 328.27 MBytes Mapped memory 17.36 MBytes Reserved block count 524 blocks Committed block count 1082 blocks Mapped block count 43 blocks So that 4.88 GBytes of reserved memory seems really big. But neither the DotNetMemoryAnalysis or the regular Memory Pressure Analyzer seems to tell me where that 4.88 GB went. How can I find out?

  Read the article

• Creating a bootable external drive in OSX

  - by Brian Postow

  I want to do some slightly dangerous testing, testing an install package I've written, so I've got an external drive, and I want to make it a bootable OSX disk, then I can boot up on the external, do my install, and if it screws things up, it doesn't actually affect the usability of my machine. The problem is that when I stick the disk that came with my computer (It's actually another computer in the office, but they're both minis) in and try to run the installer, it says "You cannot install OSx 10.6 on this computer". Now, the computer is ALREADY running 10.6, so that's a kind of silly error message... It does this when I boot to the DVDRom as well. Am I doing something really really dumb? or what?

  Read the article

• Nagios3 gives a warning on HTTP service monitoring

  - by Dez

  Already set up my local net configuration to be monitored by Nagios3. I found a problem that Nagios3 reports a warning in the HTTP monitoring service of a Debian server set at ip 192.168.1.52, that has an individual virtual host and a mass virtual host for application development. I get this status message: HTTP WARNING: HTTP/1.1 404 Not Found I used the Nagios tools to check. servername is the name of the vhost server name I used in the Apache configuration. /usr/lib/nagios/plugins/check_http -H servername -I 192.168.1.52 receiving this status message: HTTP OK HTTP/1.1 200 OK - 37900 bytes in 0.504 seconds |time=0.503946s;;;0.000000 size=37900B;;;0 But when I check like this: /usr/lib/nagios/plugins/check_http -I 192.168.1.52 I get the same status message as the warning, so I assume that I don't have Nagios completely well set up because doesn't recognize the vhosts for that server, how it should be as the check_http service shows. Where should I look to fix that warning?

  Read the article

• Windows Server 2003 Synchronize Not Sticking

  - by lkessler

  We have a Windows Server 2003. It had Raid running on 2 disks. One disk failed and the Raid Controller failed. We replaced the disk and controller and restored everything. No data was lost. The users of that server found that there were a number of directories that appeared empty. We found that from their machine, we could right-click on the directory and select "Synchronize" and the files in the directory would now be visible to them. However, when opening Internet Explorer and browsing the web and ftp'ing to a web site, the files in the directory would vanish. We would have to "Synchronize" them again to get them to reappear. What is going on to cause this need to Synchronize and then re-Synchronize again? What do we need to do to fix this so that the directories are permanently visible?

  Read the article

• Automating and deploying new linux servers

  - by luckytaxi

  I'm in the process of developing a method to automate new virtual machines into my environment. 90% of our machines are virtual but the process is similar for both physical and vmware based images. What I do now is I use cobbler to install the base OS. The kickstart script has post hooks to modify the yum repo and installs puppet and func. Once the servers are running, I manually add them into nagios and sign the certificate via the puppetmaster. I've since migrated most of the resources to use mysql as the backend. I wanted to see what others are doing and my goal for 2011 is to have puppet inventory the hardware into mysql, and somehow i'll script a python script to have nagios grab the info and automatically add it for monitoring purposes. It's kind of tedious to have to add each new server into nagios, puppet's dashboard, munin, etc...

  Read the article

• Apache: how to set custom 401 error page and save original behaviour

  - by petRUShka

  I have Kerberos-based authentication with Apache/2.2.3 (Linux/SUSE). When user is trying to open some url, browser ask him about domain login and password like in HTTP Basic Auth. If user cancel such request 3 times Apache returns 401 Authorization Required error page. My current virtual host config is <Directory /home/user/www/current/public/> Options -MultiViews +FollowSymLinks AllowOverride None Order allow,deny Allow from all AuthType Kerberos AuthName "Domain login" KrbAuthRealms DOMAIN.COM KrbMethodK5Passwd On Krb5KeyTab /etc/httpd/httpd.keytab require valid-user </Directory> I want to set nice custom 401 error page with some instructions for users. And I added such line in virtual host config: ErrorDocument 401 /pages/401 It works, when user can't authorize apache redirects him to my nice page. But Apache doesn't ask user login\password as it did before. I want this functionality and nice error page simultaneously! Is it possible to make it works properly?

  Read the article

• Customized windows xp installation

  - by user23950

  How to create a customized version of an xp installation cd. I want a hand's off installation that will install all the themes, drivers , and applications I need without my intervention. How can I do that. I tried to make use of this software called Nlite. But when I tested the iso file using virtual box. The virtual box said that there's a certain file that cannot be copied. And by the way, before I customized the original iso image of windows xp sp3, it doesn't have the file copying problem that I mentioned above.

  Read the article

• Can't launch Oneiric x64 instance on Eucalyptus

  - by Bruno Reis

  EDIT: after many hours, I've found out that the problem has nothing to do with Eucalyptus. It looks like the image is buggy. Very, very buggy. More details in the end. I didn't manage to fix it, and I will file a bug. EDIT 2: I managed to fix it, it apparently works. I have a 4-machine cluster running Ubuntu Server Natty (11.04) x64. I've installed "Ubuntu Enterprise Cloud" from the installtion CD (then updated it) on each of these machines. The cloud seems to work fine, I have lots of virtual machines running Natty servers on them. Now I'd like to run Oneiric in a virtual machine, but somehow I can't. I downloaded Oneiric's (x64) image from http://cloud-images.ubuntu.com/oneiric/current/, published it (uec-publish-tarball oneiric-server-cloudimg-amd64.tar.gz oneiric-server-cloudimg-amd64) exactly as I did with Natty, then tried to launch an instance (euca-run-instances -n 1 -k my-key -t m1.small -z my-cloud emi-XXXXXXXX) using Oneiric's image, but the instance is not able to boot. With euca-get-console-output I get the following: [ 0.461269] VFS: Cannot open root device "sda1" or unknown-block(0,0) [ 0.462388] Please append a correct "root=" boot option; here are the available partitions: [ 0.463855] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 0.465331] Pid: 1, comm: swapper Not tainted 3.0.0-13-generic #22-Ubuntu [ 0.466526] Call Trace: [ 0.466989] [<ffffffff815d3ee5>] panic+0x91/0x194 [ 0.467860] [<ffffffff81ad1031>] mount_block_root+0xdc/0x18e [ 0.468891] [<ffffffff81ad126a>] mount_root+0x54/0x59 [ 0.469829] [<ffffffff81ad13dc>] prepare_namespace+0x16d/0x1a7 [ 0.470883] [<ffffffff81ad0d76>] kernel_init+0x140/0x145 [ 0.471837] [<ffffffff815f38e4>] kernel_thread_helper+0x4/0x10 [ 0.472889] [<ffffffff81ad0c36>] ? start_kernel+0x3df/0x3df [ 0.473884] [<ffffffff815f38e0>] ? gs_change+0x13/0x13 The filesystem is labeled "cloudimg-rootfs", inside the image both /etc/fstab and /boot/grub/grub.cfg always refer to the image by the label, everything seems to be correct, yet the kernel says it can't find the root file system. I've spent many hours googling, but nothing came out. I've asked on #ubuntu-server, but nobody knew what to do. I've asked on #eucalyptus but got no answer at all. Any ideas on why this is happening and how to solve it? Thanks EDIT: after many hours, I've found out that the problem has nothing to do with Eucalyptus. It looks like the image is buggy. Very, very buggy. The first problem is that the Kernel in the image is a -generic kernel, while I suppose it should be a -virtual one. I chrooted into the image, removed the -generic packages, replaced it with the -virtual ones. Then I extracted the new kernel (and replaced the original one (-generic) that came with the tarball) because I need it when I publish and launch an image with Eucalyptus. The problem described above was solved. But then, the console started showing this: mount: mount point ext4 does not exist If you check the /etc/fstab file in the image, it says: LABEL=cloudimg-rootfs ext4 defaults 0 1 Damnt, where's my mount point? Note that it is missing /proc as well. Well, when you think it is over, you will notice that your instance will have no network connectivity. Let's check /etc/network/interface: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback Oh my! It is missing eth0... here I stopped. I can't take no more. I give up. Looks like Canonical has just forgotten to properly set up this image. At first, I though: "have I downloaded a server image by mistake?", but no, I double checked. It is really the cloud image, it has even "cloud-init" installed (which is not, by default, on server images). They just forgot to prepare it. I will file a bug (and reference it here once this is done), and hope they fix it soon! EDIT 2: it looks like the network configuration was the last thing missing. I decided to test it with the fixes above, and it booted properly! However, I haven't got the slightest idea if the image is now good to go...

  Read the article

• MS-DOSdivide overflow

  - by repozitor

  when i want to install my dear application on MS-DOS os, i see error "Divide Overflow" what is the meaning of this error and how to fix it? the procedure of installing is: 1-partitioing my HDD disk 2-format C drive 3-installing MS-DOS 4-add the flowing lines to config.sys "DEVICE=C:\DOS\HIMEM.SYS DEVICE=C:\DOS\EMM386.EXE RAM DEVICE=C:\DOS\RAMDRIVE.SYS 6000 512 64 /e" 5-insert my floppy application and then restart 6-when boot process completed, all of the thing appear correctly and i now how to do the next steps note:for installing my application i need to boot from floppy app when i have ms-dos on my hdd disk i do it successfully on the Virtual machine, Q emulator but i can't do it on the real machine, Vectra HP PC, because of divide overflow

  Read the article

• Bridging VirtualBox over OpenVPN TAP adapter on Windows

  - by Sean Edwards

  I'm trying to configure a virtual machine (VirtualBox guest running Backtrack 4) with a bridged adapter over a VPN connection. The VPN is is hosted by the cybersecurity club at my university, and connects to a sandboxed LAN designed for penetration testing against various servers that the club has built. My host (Windows 7 Ultimate) connects to the VPN fine and is assigned an IP through DHCP, but for some reason the VM can't do the same thing, and I'm not sure why. It's like OpenVPN is filtering out packets from the MAC address it doesn't recognize. I want the virtual machine to bridge over the VPN connection, because our IT office has very strict policies about what you can and can't do on the network. I want to be able to run active attacks (ARP spoofing, nmap, Nessus scans) in the sandbox environment without risking the traffic accidentally going over the university network and getting my internet access revoked. Bridging over the VPN connection and running all attacks from inside the VM would solve that problem. Any idea why the host can use this interface, but the VM can't?

  Read the article

• drive life time

  - by Remus Rigo

  hi all can anyone tell me or send me a ink about the lifetime of drives (floppy,hard disk, CD, DVD, flash...) thanks

  Read the article

• HP Probook 4530s great specs, but lagging. Hard Drive?

  - by Mark

  I have this laptop, which has a i3 processor, 4gb memory, 7200rpm hard drive. So there is nothing wrong with the specs. Even when I have no applications open, simply closing and opening windows, lags. Or opening the start menu, or dragging icons across the desktop. sometimes even the cursor lags. So I checked out the resource monitor, and the resources using disk activity are svchost Avast ------- my antivirus, but not much System (PID 4) ------ This is using a huge chunk The total disk activity fluctuates between %50 - %100

  Read the article

• Time Machine for Windows

  - by Kevin L.

  A simple Google search for "Time Machine for Windows" results in a flurry of different little apps. But instead of relying on forum anecdotes and advertisements, I call on the much wiser Super User beta community for some depth on this one. Having Time Machine running on Leopard is like a warm, fuzzy blanket of comfort that I never got with RAID, rsync, or SyncToy on Windows. I'm not asking the community what the "best" backup software for Windows is, but instead: Is there any true Time Machine clone for Windows, one that includes as many of the following as possible: Completely transparent, "set-it-and-forget-it" backup Incremental backups (changes only) for every hour for a day, every day for a month, and every week until the backup disk is full Ability to rebuild from this backup disk in case of main drive meltdown (the backup doesn't have to be bootable; neither are Time Machine disks) Extremely easy to use UI (target user == wife). Bonus points for a beautiful UI

  Read the article

• Office 2011 Mac - Unable to save Word files, plus normal.dot alert errors

  - by Jeff D

  There are actually 3 errors here. When I open Word, I get: Word cannot open the existing global template. () If I create a file, type a character and try to save to the desktop (that I have no problems writing to otherwise), I get: Word cannot save or create this file. The disk may be full or write-protected. Try one or more of the following: * Free more memory * Make sure that the disk you want to save the file on is not full, write-protected, or damaged. () I am just saving to the desktop, and I can save excel files (or anything else) there. After the failure, if I save again, the default file name becomes: .doc...doc Weird. Finally, when I close word completely, I get: Do you want to replace the existing Normal.dotm.

  Read the article

• Can PHP be run in Apache via mod_php and mod_fcgi side by side?

  - by Mario Parris

  I have an existing installation of Apache (2.2.10 Windows x86) using mod_php and PHP 5.2.6. Can I run another site in a virtual host using FastCGI and a different version of PHP, while stilling running the main site in mod_php? I've made an attempt, but when I add my FCGI settings to the virtual host container, Apache is unable to restart. httpd.conf mod_php settings: LoadModule php5_module "C:\PHP\php-5.2.17-Win32-VC6-x86\php5apache2_2.dll" AddHandler application/x-httpd-php .php PHPIniDir "C:\PHP\php-5.2.17-Win32-VC6-x86" httpd-vhosts.conf fastcgi settings: <VirtualHost *:80> DocumentRoot "C:/Inetpub/wwwroot/site-b/source/public" ServerName local.siteb.com ServerAlias local.siteb.com SetEnv PHPRC "C:\PHP\php-5.3.5-nts-Win32-VC6-x86\php.ini" FcgidInitialEnv PHPRC "C:\PHP\php-5.3.5-nts-Win32-VC6-x86" FcgidWrapper "C:\PHP\php-5.3.5-nts-Win32-VC6-x86\php-cgi.exe" .php AddHandler fcgid-script .php </VirtualHost> <Directory "C:/Inetpub/wwwroot/site-b/source/public"> Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All Order allow,deny Allow from all </Directory>

  Read the article

• Recommended RAM and disc space for Oracle 11g on Windows

  - by Álvaro G. Vicario

  I need to provide the recommended amount of RAM and disc space (divided in two partitions) so the customer can create an appropriate virtual machine to run Oracle. All I could find in the documentation was a brief listing with minimum RAM and typical/advanced install types. The virtual machine will run latest Oracle Standard Edition One (11g release 2 so far) under Windows Server 2008 x64 and will host a reasonably low traffic web application. How much RAM and disc must I ask for in order to be safe? (Feel free to ask for further details if I've omitted something relevant.) Update: Rough estimations: Database size: 10 MB after installation Growth rate: +3MB per day on average Size of database 'active' data: (not sure of what this means, there's not actual archive so I guess all data is current) Amount of data written per second in peak hours: a few KB Number of client sessions: 3 or 4 at most Frequency and response size of most heavy requests: some reports make heavy table JOINS that need up to 20 seconds to complete but they won't return more than a few thousand rows with plain text. The app also handles BLOBs (typical size from 50KB to 200KB)

  Read the article

• Slow file operations, possible I/O error but chkdsk says OK

  - by mikolajek

  I've recently faced a strange problem. I use Directory Opus file manager that suddenly started to report an I/O error when trying to copy files onto one of my disks. The Windows Explorer did copy those files but it was extremely slow. I run chkdsk on this drive (ca. 300GB) and it took it over two days to complete! However it reported no errors found. I run Hard Disk Sentinel that says the drive is OK. But the files still read and write extremely slow! Can anyone advise me what to do? I have a spare space I am copying my files for backup now but should I get rid of this disk? Or can I try to "heal" it somehow? Many thanks for your ideas!

  Read the article

< Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >