Search Results

Search found 25397 results on 1016 pages for 'network map'.

Page 278/1016 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• ZoneAlarm Internet Security Suite

  Five interlocking security services for the ultimate in network protection

  Read the article

• NetSetMan

  A handy freeware tool for helping you efficiently view and manage all your network settings

  Read the article

• Windows Not Sleeping All Night

  - by John Paul Cook

  Having a computer wake up when you don’t want it to wastes electricity and drains the battery on mobile devices. My desktop had been waking up at night, so I assumed it was some network traffic on my home network. I unchecked Allow this device to wake the computer on my network adapters . Figure 1. Network adapter Power Management tab. That didn’t solve the problem. I included the screen capture in Figure 1 because it could be part of the solution for someone else. To identify the root cause instead...(read more)

  Read the article

• Wireless Not Working with Drivers Installed

  - by Haoran

  I'm new to Linux. I installed Ubuntu 12.10 on my old Compaq/Hp Preario V3000 to replace Windows XP. Every thing works fine except I'm getting no wireless network options in the network drop down menu. I'm using a cable at the moment. Wirless chipset is: 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02) I ran rfkill: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no I also ran iwconfig and got this lo no wireless extensions. eth0 no wireless extensions. In the additional drivers it says: "Using Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source (proprietary)" Any help to resolve the problem would be greatly appreciated.

  Read the article

• No Internet Connection - ubuntu 11.10

  - by emersonhsieh

  I installed Ubuntu 11.10 recently. After the first bootup the computer freezes so I have to force-quit my computer. Then I turned on my computer after that. I tried connecting to the internet. My (and my neighbor's) wireless networks shown up, but no matter how many times I tried, I can't connect to my home network. I checked the password and the other laptop's internet works (a MacBookPro). It was a wireless network. What's weird is that the Wireless network worked when I was installing ubuntu How can I connect to the internet now? I don't have a wired network. Please Help! Any help will be appreciated Specs: ASUS F81Se, Windows 7 Dual-boot, I remember the wireless card was made by Atheros, 4GB RAM

  Read the article

• Regulating outgoing traffic on ubuntu VM

  - by DazSlayer

  I am making a virtual network setup for my high school cybersecurity team to practice. I am connecting all the VMs together through a VPN and then people who are practicing will VPN in and ssh/remote desktop into the different VMs. The problem is that for practicing, they will need root access into the VMs and because the VMs are connecting to my personal network, the VMs pose a security risk to my personal network. Is there any way in either VMWare or VirtualBox or even making an unchangeable iptable (I can make all the windows VMs go thru a linux VM) to prevent people from connecting to my local network via the VM?

  Read the article

• Ubuntu Connect Button Disabled, cannot connect

  - by CSharperWithJava

  I'm trying to connect to my school network from Ubuntu 12. The network is WPA encrypted and I can connect just fine if the network manager establishes a connection automatically. However, when I get disconnected and try to reconnect a username and password prompt pops up. The credentials are already stored and are autofilled in correctly, but the Connect button is disabled so I can't actually connect to the network. What can I do? The only guess I've found so far is the password is too short and Ubuntu is expecting a full WPA key. I don't administer the school network though so I certainly can't change that.

  Read the article

• Internet Magic (Proxy sever) windows application

  Windows application which create proxy server to share Internet over any TCP/IP network

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• Why are my scene's depth values not being written to my DepthStencilView?

  - by dotminic

  I'm rendering to a depth map in order to use it as a shader resource view, but when I sample the depth map in my shader, the red component has a value of 1 while all other channels have a value of 0. The Texture2D I use to create the DepthStencilView is bound with the D3D11_BIND_DEPTH_STENCIL | D3D11_BIND_SHADER_RESOURCE flags, the DepthStencilView has the DXGI_FORMAT_D32_FLOAT format, and the ShaderResourceView's format is D3D11_SRV_DIMENSION_TEXTURE2D. I'm setting the depth map render target, then i'm drawing my scene, and once that is done, I'm the back buffer render target and depth stencil are set on the output merger, and I'm using the depth map shader resource view as a texture in my shader, but the depth value in the red channel is constantly 1. I'm not getting any runtime errors from D3D, and no compile time warning or anything. I'm not sure what I'm missing here at all. I have the impression the depth value is always being set to 1. I have not set any depth/stencil states, and AFAICT depth writing is enabled by default. The geometry is being rendered correctly so I'm pretty sure depth writing is enabled. The device is created with the appropriate debug flags; #if defined(DEBUG) || defined(_DEBUG) deviceFlags |= D3D11_CREATE_DEVICE_DEBUG | D3D11_RLDO_DETAIL; #endif This is how I create my depth map. I've omitted error checking for the sake of brevity D3D11_TEXTURE2D_DESC td; td.Width = width; td.Height = height; td.MipLevels = 1; td.ArraySize = 1; td.Format = DXGI_FORMAT_R32_TYPELESS; td.SampleDesc.Count = 1; td.SampleDesc.Quality = 0; td.Usage = D3D11_USAGE_DEFAULT; td.BindFlags = D3D11_BIND_DEPTH_STENCIL | D3D11_BIND_SHADER_RESOURCE; td.CPUAccessFlags = 0; td.MiscFlags = 0; _device->CreateTexture2D(&texDesc, 0, &this->_depthMap); D3D11_DEPTH_STENCIL_VIEW_DESC dsvd; ZeroMemory(&dsvd, sizeof(dsvd)); dsvd.Format = DXGI_FORMAT_D32_FLOAT; dsvd.ViewDimension = D3D11_DSV_DIMENSION_TEXTURE2D; dsvd.Texture2D.MipSlice = 0; _device->CreateDepthStencilView(this->_depthMap, &dsvd, &this->_dmapDSV); D3D11_SHADER_RESOURCE_VIEW_DESC srvd; srvd.Format = DXGI_FORMAT_R32_FLOAT; srvd.ViewDimension = D3D11_SRV_DIMENSION_TEXTURE2D; srvd.Texture2D.MipLevels = texDesc.MipLevels; srvd.Texture2D.MostDetailedMip = 0; _device->CreateShaderResourceView(this->_depthMap, &srvd, &this->_dmapSRV);

  Read the article

• Upgrade from 11.04 to 11.10, getting "W:Failed to fetch gzip..."

  - by Michael Durrant

  Error during update A problem occurred during the update. This is usually some sort of network problem, please check your network connection and retry. W:Failed to fetch gzip:/var/lib/apt/lists/partial/us.archive.ubuntu.com_ubuntu_dists_oneiric_universe_i18n_Translation-en Encountered a section with no Package: header , E:Some index files failed to download. They have been ignored, or old ones used instead. I can browse web sites normally during this time though (my network is ok).

  Read the article

• How do I bridge my wireless to my wired connection?

  - by gatoatigrado

  I want to bridge the wireless connection with the wired connection. The wireless is the host and the wired is the client, so to speak. Internet sharing (inet <--> wifi <--> ethernet) I tried to bridge my ethernet connection by going to network manager edit connections wired edit IPv4 settings shared to other computers Screenshots However, it seems to automatically disconnect half a second after it says "connection established"! edit 2 got the network manager logs, it seems the address is in use. See http://pastebin.com/DjqRshxW , line 45. nm-tool output is here: http://pastebin.com/x5Aci5V1 . I tried firestarter, as mentioned in another thread, and no luck. I don't have time to bother with a dozen command line tricks, unless is copy & pasting a shell script... so please suggest ways that use GUIs and/or won't leave my computer in a confused state (e.g. disabling network manager, manually connecting to a WPA network, installing brutils, etc.). edit: one idea that would work, if it's possible -- is there a way to share connections via SSH and SOCKS5? I'd need to do this at a system-wide level though; I only know how to do it through the browser now. Then, I could run ifconfig eth0 192.168.4.1 on the computer sharing the inet, and ifconfig eth0 192.168.4.2 on the computer I'm trying to share with; I know this does work for host-to-host transfers. edit 3 If I run sudo killall dnsmasq, then nothing is using the 10.42.43.1 address the network manager sharing wants to use. But now it just takes longer to die, with error "NetworkManager[5935]: dnsmasq died with signal 9" [ http://pastebin.com/4FNtpugi ]. Looking at just the commands [ http://pastebin.com/1vrtQeWk ], maybe it's trying to route eth0 to itself? I'm not that familiar with networking things though.

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• Deep-protocol analysis of UNIX networks

  <b>developerWorks: </b>"Whether you are monitoring your network to identify performance issues, debugging an application, or have found an application on your network that you do not recognize, occasionally you need to look deep into the protocols being used on your UNIX network to understand what they are doing."

  Read the article

• Setting Default Ubuntu eth port

  - by No1_Melman

  Background: I have a desktop computer running Ubuntu 12.04. I have installed DRBL to handle DHCP server and Clonezilla Server. I have a network card in my desktop with 2 ports in it. These 2 ports are bonded together and are used by DRBL. There is a 3rd port integrated in the motherboard. I want to use this 3rd port for internet. DRBL knows that this is set for internet. Ubuntu Network-Manager has stopped recognising the connections (device not managed). It use to say that eth1 was default (first port in the network card) I want eth0 to be default as that is the Internet port. Question: How do I make network-manager see eth0 as the defualt port?

  Read the article

• Bonding and default gateway problem (CentOS)

  - by lg

  I configured network bonding on two machine with centos 5.5. Bonding works well, but the problem is default gateway: it is not configured! I follow this tutorial. I added GATEWAY in both (and either) /etc/sysconfig/network and /etc/sysconfig/network-scripts/ifcfg-bond0. But, when I restart network (or server) there is no default gateway (route command). This is ip route ls output after network restart: 10.0.0.0/16 dev bond0 proto kernel scope link src 10.0.0.88 Where is my mistake?

  Read the article

• No WIFI on Ubuntu 12.04 LTS after today software update

  - by Adchara

  I just got new dell inspiron3537 with Ubuntu 12.04 LTS (no windows O/S). It got some wireless (hard block) yesterday. So, this morning, I ran the software update all the security update. After that I can't see "Wireless" in system setting. So, I updated all the software update and looked thru several web site and found "sudo lshw -c network" command. I tried and found the result below. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: 74:86:7a:40:5d:48 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.10 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:60 ioport:4000(size=256) memory:c0700000-c0700fff memory:c0400000-c0403fff *-network UNCLAIMED description: Network controller product: QCA9565 / AR9565 Wireless Network Adapter vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0600000-c067ffff memory:9fb00000-9fb0ffff Please suggest what I should do to fix it. Thx in advance

  Read the article

• How to make a backup VPN server?

  - by akalenuk

  I have a small VPN network with a bunch of clients working mostly with each other and a VPN server. Everything works fine, except, obviously I can't shut VPN server down without breaking the network. I have a spare machine, which worked as an VPN server for the same network before so it is signed with the same SA as the first one and basically configured just the same as the first one. Technically I can make my clients work with it with little adjustment (by setting remote in etc/openpvn/clientx.conf), but it would be great make this switch automated. So basically I want two VPN servers running in the same network to work completely interchangeable without clients even knowing this. Can I do this with VPN or should I dig deeper into physical network layer?

  Read the article

• Wireless does not work 12.10

  - by superkoop

  My primary issue is that my wireless does not work after I installed 12.10. The output to rfkill list all: 5: hci0: Bluetooth Soft blocked: no Hard blocked: no The output to lshw -class network is: *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 12 serial: 00:21:9b:d6:46:51 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:fe8fc000-fe8fffff ioport:de00(size=256) *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:17 memory:fe7fc000-fe7fffff The output to lspci -nn for the pertinent information is: 0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Thus, it seems the solution would be to run: sudo apt-get install linux-headers-generic sudo apt-get install --reinstall bcmwl-kernel-source sudo modprobe wl However, I do not currently have access to an ethernet connection, as I am currently only able to use verizon wireless 3g internet. Thus, is there a way to set up ICS with a Vista machine so that I can access the internet by using the Vista machine as the host? Or, is it possible to fix this by downloading the important packages in vista and moving them to ubuntu via USB drive?

  Read the article

• After upgrade to 12.04 wireless keeps dropping on BCM4312

  - by Sheket

  I know there are plenty of questions very similar to these, but I've tried practically everything and it still isn't working. Some solutions get the wireless connection working, but it goes very slow and drops after a few minutes. Then it won't reconnect and keeps asking for password. Hope you can help me. Thanks in advance. This is the output for sudo lshw -C network *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:f0300000-f0303fff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: c0 serial: 00:23:5a:9b:6e:b1 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:f0200000-f023ffff ioport:a000(size=128) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:24:2c:83:f0:81 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-30-generic firmware=478.104 link=no multicast=yes wireless=IEEE 802.11bg And for lsmod | grep b43 b43 342643 0 mac80211 436455 1 b43 cfg80211 178679 2 b43,mac80211 bcma 25651 1 b43 ssb 50691 1 b43 And for rfkill list 5: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• ZoneAlarm FREE

  Five interlocking security services for the ultimate in network protection

  Read the article

• Fluent NHibernate Mapping and Formulas/DatePart

  - by Alessandro Di Lello

  Hi There, i have a very simple table with a Datetime column and i have this mapping in my domain object. MyDate is the name of the datetime column in the DB. public virtual int Day { get; set; } public virtual int Month { get; set; } public virtual int Year { get; set; } public virtual int Hour { get; set; } public virtual int Minutes { get; set; } public virtual int Seconds { get;set; } public virtual int WeekNo { get; set; } Map(x => x.Day).Formula("DATEPART(day, Datetime)"); Map(x => x.Month).Formula("DATEPART(month, Datetime)"); Map(x => x.Year).Formula("DATEPART(year, Datetime)"); Map(x => x.Hour).Formula("DATEPART(hour, Datetime)"); Map(x => x.Minutes).Formula("DATEPART(minute, Datetime)"); Map(x => x.Seconds).Formula("DATEPART(second, Datetime)"); Map(x => x.WeekNo).Formula("DATEPART(week, Datetime)"); This is working all great .... but Week Datepart. I saw with NHProf the sql generating for a select and here's the problem it's generating all the sql correctly but for week datepart.. this is part of the SQL generated: ....Datepart(day, MyDate) ... ....Datepart(month, MyDate) ... ....Datepart(year, MyDate) ... ....Datepart(hour, MyDate) ... ....Datepart(minute, MyDate) ... ....Datepart(second, MyDate) ... ....Datepart(this_.week, MyDate) ... where this_ is the alias for the table that nhibernate uses. so it's treating the week keyword for the datepart stuff as a column or something like that. To clarify there's no column or properties that is called week. some help ? cheers Alessandro

  Read the article

• Android: How to obtain Mac Address of WiFi Network Interface?

  - by Gubatron

  It seems the java.net.NetworkInterface implementation of android does not have a byte[] getHardwareAddress() method http://developer.android.com/reference/java/net/NetworkInterface.html I've found several forums of people trying to do this with no definitive answer, I need to get a somewhat cross-device UUID, so I can't rely on phone numbers or in ANDROID_ID (which can be overwritten and which I think depends on the user having a google account) http://developer.android.com/reference/android/provider/Settings.Secure.html#ANDROID_ID In linux you can use ifconfig or read from /proc/net/arp and you can easily get the Hardware address. Is there a file in android that I can read? There has to be a way to get this address since it's shown in the "Settings About Phone Status" of the phone.

  Read the article

• Howto use Windows Authentication with SQL Server 2008 Express on a workgroup network?

  - by mbadawi23

  I have two computers running SQL Server 2008 Express: c01 and c02, I setup both for remote connection using windows authentication. Worked fine for c02 but not for c01. This is the error message I'm getting: TITLE: Connect to Server Cannot connect to ACAMP001\SQLEXPRESS. ADDITIONAL INFORMATION: Login failed. The login is from an untrusted domain and cannot be used with Windows authentication. (Microsoft SQL Server, Error: 18452) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=18452&LinkId=20476 BUTTONS: OK I don't know if I'm missing something, here is what I did: Enabled TCP/IP protocol for client from Sql Server Configuration Manager. Modified Windows firewall exceptions for respective ports. Started the Sql Browser service as a local service Added Windows user to this group: "SQLServerMSSQLUser$c01$SQLEXPRESS" From Management Studio, I added "SQLServerMSSQLUser$c01$SQLEXPRESS" to SQLEXPRESS instance's logins under security folder, and I granted sysadmin permissions to it. Restarted c01\SQLEXPRESS Restarted Sql Browser service. There is no domain here. It's only a workgroup. Please any help is appreciated, Thank you.

  Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >