Search Results

Search found 25397 results on 1016 pages for 'network map'.

Page 281/1016 | < Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >

• Linux Mounting Problem

  - by Sam

  I have an Iomega Network Attached Storage device on my Windows network. I am trying to use a clonezilla live USB flash drive to backup my netbook to my Iomega Network Attached Storage device. The clonezilla USB flash drive runs linux. I'm having trouble getting the Network Attached Storage unit to mount using the following command: mount -t cifs -o username="myUsername" //192.168.1.100/backup /home/partimg The response from linux is: [134.730738] CIFS VFS: cifs_mount failed w/return code = -6 retrying with upper case share name [134.788461] CIFS VFS: cifs_mount failed w/return code = -6 mount error(6): No such device or address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) I also tried adding the following to my username: username="myUsername,domain=workgroup" but that did not change the error. I am able to ping the network attached storage unit from linux on my netbook. I also booted from a Slax Live USB Flash Drive and Slax auto-mounted my network attached storage unit via Samba. Unfortunately, I don't believe that I can run clonezilla from inside the Slax installation. Does anyone have any insight about what is wrong with my mount statement? Or is there something peculiar about Iomega drives which makes this impossible?

  Read the article

• Local DNS and Apache Server Configuration Interferring - example.com / www.example.com

  - by nicorellius

  I have a domain for my site: example.com I am also running local DNS with these lines: www IN CNAME server.<host_provider>.com. dev IN CNAME server.<host_provider>.com. So www.example.com and dev.example.com go to production and development sites, respectively, that are hosted by a host company. In my Apache configuration for the main site, I'm running a rewrite rule like this: RewriteEngine ON RewriteCond %{HTTP_HOST} ^example\.com$|!dev\.example\.com$ [NC] RewriteRule ^(.*)$ http://www\.%{HTTP_HOST}/$1 [R=302,L,NE] This rule seems to work, as when you are off the network and go to example.com in the browser, you get redirected to www.example.com. The problem is when I'm on the network, and I go to example.com I get an error page, saying page can't be found. No server errors; just a page can't be found, as if the local DNS is causing it to stop looking at that point. I'm also using Nettica for DNS service and have this A record in place: example.com Host (A) Default xxx.xx.xxx.xx This handles the external DNS, but my problem seems to be related to my internal DNS. For example, inside my network, I can go to servers on the network with addresses like this: server.example.com server1.example.com server2.example.com These are configured in my local DNS. I'm just not sure how to get past the "empty" subdomain and go to example.com. Adding to this since it might not be clear. If I'm out side the example.com network, on another network, like example123.com, then when I go to example.com I'm redirected to www.example.com as expected, eg, the Apache rewrite rule is working. Thanks in advance for any information.

  Read the article

• When I restart my LXC environment, the container does not re-bind to the IP address

  - by RoboTamer

  The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

  Read the article

• Updating Cisco VPN config to add vpnc support

  - by Igor Kuzmitshov

  I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access (PPTP) — using vpdn-group with accept-dialin protocol pptp. Now, a new partner wants to connect using vpnc client. The latter needs IPSec ID (group name) and IPSec secret in addition to username and password. I guess that IPSec secret is pre-shared key that can be specified in crypto isakmp key on Cisco. But I could not find any VPN tutorials involving groups. Hence, my questions: How to add IPSec ID (group name) and IPSec secret on Cisco router for vpnc connections? Should I add a new crypto map matching all addresses as well? Is it possible to add this configuration without breaking the existing setup? Thank you.

  Read the article

• flowchart for debugging a slow/unresponsive server

  - by davidosomething

  So the server is slow: Roll back to the previous known working build - Success? Code problem - Fail? Go on. Ping ip address - Success? maybe a DNS problem, go on. - Fail? Server or connection problem, go on. Ping and tracert your domain.com from inside your network - previous success - fail: DNS problem - success? go on. - previous fail and: - Fail? Go on, could be you or network. - Success? Go on. Try it from outside your network (http://centralops.net/co/) - Fail? The server's network connection sucks. - Success? If inside network was fail, your network sucks. Check the server load: CPU/RAM usage. Is it overloaded? - Yes. Who's the culprit? Kill some processes/reboot. - No? Go on. what other steps should i add?

  Read the article

• Block Skype on Cisco IOS

  - by ensnare

  I'm trying to block skype via policy routing but it's not working ... here's my configuration: class-map match-any block match protocol skype policy-map QoS-Priority-Input class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop policy-map QoS-Priority-Output class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop interface FastEthernet4 description WAN service-policy input QoS-Priority-Input service-policy output QoS-Priority-Output

  Read the article

• ffmpeg add two audio streams to video

  - by Tossin Hausen

  I tried this: ffmpeg -i /sdcard/video/transcode/video.avi -map 0:0,0 -i /sdcard/video/transcode/first.mp3 -map 1:0,1 -i /sdcard/video/transcode/second.mp3 -map 2:0,2 -acodec copy -vcodec py /sdcard/video/transcode/Output.avi to add two audio streams to one video file. But ffmpeg says the number of mappings should match the number of output streams. What is wrong here? I'm trying to work with an Android build of FFmepg "ffmpeg for android beta". "Does not work" means that this uncommunicative Android build of FFmpeg just stops without giving any error message. The -codec copy option does not work with this build. Now I tried the same set of files with the FFmpeg called command line tool that comes with Ubuntu 10. Something (can't say where it is from). The -codec copy option does not work with this FFmpeg too. Here the complete output: m30x:~/movie/Film$ ffmpeg -i input.avi -i first.mp3 -i second.mp3 -map 0 -map 1 -map 2 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x93cfd10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Input #2, mp3, from 'second.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #2.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Number of stream maps must match number of output streams Merging only one audio stream with the video stream works with Ubuntu and Android version of FFmpeg. Here the complete output: ffmpeg -i input.avi -i first.mp3 -map 0 -map 1 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x9bfad10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Output #0, avi, to 'output.avi': Stream #0.0: Video: mpeg4, yuv420p, 576x432, q=2-31, 90k tbn, 25 tbc Stream #0.1: Audio: libmp3lame, 22050 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding frame= 6157 fps=6156 q=-1.0 size= 31667kB time=246.28 bitrate=1053.3kbits/s Do you have an idea why it does not work with two audio streams? By the way, ffmpeg -i input_with_first_audio_stream.avi -i second.mp3 -acodec copy -vcodec copy output_two_audio_streams.avi -newaudio works with both versions of ffmpeg that I use, but the first audio stream is played too fast (x10 or more), while the second audio stream is played correct. Many thanks in advance and sorry for my unconventional question and outdated versions of ffmpeg. But I am a lamer and it is not so easy for me to compile from the source (especially for the Android version). I will try to compile an up to date version of ffmpeg with Ubuntu, but I don't have much free time.

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• Unable to ping gateway via bridge nic

  - by Ara

  I'm trying to install KVM on Ubuntu 12.04 server. We have multiple nic on this server of which we primarily use eth0. The server network runs fine(i'm able to ping gateway, ping dns server and ping servers on internet) with eth0 /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local I installed bridge-utils and configured br0 as below /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off Post which i'm able to ping servers on the same ip range 192.168.22.2-254 except for 192.168.22.1 (which is the gateway) also i'm not able to ping any other servers. I'm not able to ping this machine from network. The output for route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.22.1 0.0.0.0 UG 100 0 0 br0 192.168.22.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 I've been struggling with this issue for past 5 days, would be of help if anyone can point me in the right direction to fix this issue. Thanks in advance

  Read the article

• pfsense, active directory, local domain

  - by Dalton Conley

  First things first, I have no idea what I'm doing. Certainly not afraid to admit that.. but here is my network setup. I have 2 servers, one of them in a domain controller. Both are running windows server 2008. They have replicated directories. Each server is at a different location and has its own firewall for the network at that location. Both firewalls are using pfsense. Recently a firewall went down and my coworker reinstalled pfsense, and everything seems setup correctly. Again, I have no idea what I'm doing so I'm not sure. I have records from when the previous IT person had setup this network and the firewall settings are the same but those records could have been extremely old. Now, I have a domain name for my network.. we'll call it "mydomain.net". I use to be able to access this domain name and it would bring up the servers replicated drives(i.e. \\mydomain.net). Now I cannot. I can however access the servers individual host names on my network(i.e. \\server1 , \\server2). We didn't change anything on the server which is what makes me think its something to do with the firewall. I know this is probably a very general question and I don't have a lot of detail to add but could anyone give me some insight on to what could be causing this, or some debugging techniques I can apply to this? I'm a programmer, not a network administrator.

  Read the article

• Anonymous access to SMB share hosted on Server 2008 R2 Enterprise

  - by bwerks

  Hi all, First off, I have read through this post and a whole slew of non-SF posts which seem to address the same or a similar problem, however I was still unable to fix my problem. I've got three machines in this situation: a domain-joined server that runs Server 2008 R2 Enterprise ("share server") a domain-joined workstation running XP Pro SP3 ("test server") a domain-unjoined test server running Server 2003 R2 SP2 ("workstation") The share server is exposing a share on the network that the test server must access--it's a Source/Symbol Server share for our debugging purposes. I believe visual studio simply accesses the the share with its own credentials in this case, meaning that the share must be accessible anonymously since the test server isn't joined to the domain and there's no opportunity to supply domain authentication. I've attempted a lot of things to avoid the authentication window when accessing the share: I've enabled the Guest account on the share server and given Guest full sharing/NTFS permissions for the share. I've given ANONYMOUS LOGON full sharing/NTFS permissions for the share. I've added my share to “Network Access: Shares that can be accessed anonymously” in LSP. I've disabled “Network access: Restrict anonymous access to Named Pipes and Shares” in LSP. I've enabled “Network access: Let Everyone permissions apply to anonymous users” in LSP. Added ANONYMOUS LOGON to “Access this computer from the network” in LSP. Added the Guest account to “Access this computer from the network” in LSP. Attempted to provision the share using the Share and Storage Management MMC snap-in. Unfortunately when I attempt to access the share from the test server, I still see the prompt and I'm forced to enter "Guest" manually. I also tried this workflow using the local administrator account on a workstation, and the same thing happens both with and without XP Simple File Sharing enabled. Any idea why I'm getting these results, or what I should have done differently?

  Read the article

• how to setup a bridge with 2 NICs and few virtual machines

  - by Bond

  Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

  Read the article

• Intranet Setup for Small business any resources?

  - by Rogue

  Want to setup an intranet for a small business setup. Current Setup 28 computers running Windows ( few older pc's run Windows Xp but most run Windows 7) Spare Dell Pentium 3 which can run as a server. 6 switches spare NIC's and lots of lan cable available for networking. 3 Independent Internet connections Currently we have 3 independent networks which share internet connections, each network uses a different internet connection. Current network is setup solely to share the internet connection. What I need to achieve in this intranet Setup one common network. Instant file transfer via local network (maybe setup a file server?) Local text and voice messenger software Bridge the 3 internet connections and route all the internet connections from the main server Ability to allow or deny internet access to any computer on the network. Remote access from the main server to the client pc's on the network to debug software issues What operating system should I use on the main server? Do I need a hardware firewall? Any setup guides / resources or how-to's on how I can achieve the above requirements.

  Read the article

• Linux wireless disconnect every 20 minutes

  - by james

  My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

  Read the article

• DHCP Relay setup in ubuntu server

  - by jerichorivera

  I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

  Read the article

• Wireless router setup for 1-1 NAT

  - by Carlos

  What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

  Read the article

• How do I Implement VLAN Rate Limiting or QOS for a Cisco 2960?

  - by evolvd

  I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

  Read the article

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• How do I Implement Per VLAN Rate Limiting or QOS for a Cisco 2960?

  - by evolvd

  I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

  Read the article

• Ubuntu IP Configuration - multiple subnets & interfaces

  - by HaydnWVN

  Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

  Read the article

• Debian Wheezy IPv6 isn't configured with ifup post-up hook

  - by aef

  We recently set up a server on Debian Wheezy Beta 3 (x86_64) which has a native IPv6 connection. We configured the eth0 interface to get the IPv6 configuration through some post-up hook commands in /etc/network/interfaces. The result is, that after the booting the system up, there is only IPv4 and an auto-configured link-local IPv6 address configured on the interface, as if the command has never been executed. When we additionally place the commands after the call to ifup -a inside the /etc/init.d/networking init script, everything works as expected and we have a fully configured interface after booting up. This is quite an ugly way to configure the interface. What are we doing wrong with the ifup post-up hooks? Or is this a bug? The section from /etc/network/interfaces looks like this (IP-addresses changed): allow-hotplug eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld post-up ip -6 addr add 2001:db8:100:3022::2 dev eth0 post-up ip -6 route add fe80::1 dev eth0 post-up ip -6 route add default via fe80::1 dev eth0 I also tried it in this alternative way: auto eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld iface eth0 inet6 static address 2001:db8:100:3022::2 netmask 64 gateway fe80::1 What we added to /etc/init.d/networking: … case "$1" in start) process_options check_ifstate if [ "$CONFIGURE_INTERFACES" = no ] then log_action_msg "Not configuring network interfaces, see /etc/default/networking" exit 0 fi set -f exclusions=$(process_exclusions) log_action_begin_msg "Configuring network interfaces" if ifup -a $exclusions $verbose && ifup_hotplug $exclusions $verbose # Our additions ip -6 addr add 2001:db8:100:3022::2 dev eth0 ip -6 route add fe80::1 dev eth0 ip -6 route add default via fe80::1 dev eth0 then log_action_end_msg $? else log_action_end_msg $? fi ;; …

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• What can be done to improve time synchronization on networks with sporadic internet access?

  - by anregen

  I'm looking for advice setting up time servers for a very non-typical network. I support many closed networks that have occasional access to the internet. A network would get access most days for a few hours, but would frequently go 1-3 weeks blacked-out. The computers/servers on this network are mostly *nix-based, but not all the same flavor. The entire network is mobile, so when it connects, it will have very different hops/latency to internet time servers. The servers on the closed network are powered-off frequently (at least daily). Right now, my gut tells me to use NTP (because I hate re-learning all the stuff that someone else already got working pretty well). But I have several issues, and am looking for someone with experience in this type of strange situation. I currently have no solution in place, I'm simply letting the internal clocks drift. This results in errors of ~600s in a majority of networks. I have seen mismatch worse than 10,000s. Is there something "better" than NTP in this situation? I know NTP likes to have very frequent, consistent access to servers that give nearly identical answers. I won't have that. How many internal NTP servers should I configure, so that during periods of internet blackout, I have internal time that is consistent within the closed network? There is no human access. No matter how large the mismatch, the server(s) must attempt to correct itself. Discrete steps are very bad. No matter how large the mismatch, the correction must be "slewed", not "stepped". I understand that this could take many hours to correct.

  Read the article

• Why is piping dd through gzip so much faster than a direct copy?

  - by Foo Bar

  I wanted to backup a path from a computer in my network to another computer in the same network over a 100MBit/s line. For this I did dd if=/local/path of=/remote/path/in/local/network/backup.img which gave me a very low network transfer speed of something about 50 to 100 kB/s, which would have taken forever. So I stopped it and decided to try gzipping it on the fly to make it much smaller so that the amount to transfer is less. So I did dd if=/local/folder | gzip > /remote/path/in/local/network/backup.img.gz But now I get something like 1 MB/s network transfer speed, so a factor of 10 to 20 faster. After noticing this, I tested this on several paths and files and it was always the same. Why does piping dd through gzip also increase the transfer rates by a large factor instead of only reducing the bytelength of the stream by a large factor? I'd expected even a small decrease in transfer rates instead, due to the higher CPU consumption while compressing, but now I get a double plus. Not that I'm not happy, but just wondering. ;)

  Read the article

< Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >