Search Results

Search found 12144 results on 486 pages for 'old'.

Page 278/486 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

• configuring USB modem( Huawei EC156) in ubuntu 13.10

  - by user205427

  I am facing difficulty in installing my USB modem in Ubuntu 13.10. Contrary to what many have suggested,it does not get detected automatically, nor does setting a new connection help. USB Device is listed in lsusb, but not under network manager or Devices, it is detected as a CD-ROM, what I understood from the web was that usb-modeswitch can be used to switch it to a USB device. Even 'Enable Mobile Broadband' option is not shown in network manager. What was interesting is when I start laptop with windows 7 and use the USB modem and after that restart with Ubuntu, both Enable Broadband and the mobile broadband connection can be seen. Sadly, internet connection could not be installed. I tried using USB-modeswitch command as suggested somewhere, but it does not seem to work. Following is the message. Take all parameters from the command line * usb_modeswitch: handle USB devices with multiple modes * Version 2.0.1 (C) Josua Dietze 2013 * Based on libusb1/libusbx ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1505 HuaweiMode=1 NeedResponse=0 InquireDevice enabled (default) Look for default devices ... found USB ID 8087:0020 found USB ID 1d6b:0002 found USB ID 0461:4db6 found USB ID 12d1:1505 vendor ID matched product ID matched found USB ID 138a:0007 found USB ID 03f0:231d found USB ID 8087:0020 found USB ID 1d6b:0002 Found devices in default mode (1) Access device 005 on bus 001 Get the current device configuration ... OK, got current device configuration (1) Use interface number 0 Use endpoints 0x08 (out) and 0x87 (in) Inquire device details; driver will be detached ... Looking for active driver ... OK, driver detached INQUIRY message failed (error -9) USB description data (for identification) ------------------------- Manufacturer: HUA?WEI TECHNOLOGIES Product: HUAWEI Mobile Serial No.: ??????????????????? ------------------------- Send old Huawei control message ... -> Run lsusb to note any changes. Bye! I am stuck with this problem for 4 days now, any help would be appreciated

  Read the article

• Site Web Analytics not updating Sharepoint 2010

  - by Rohit Gupta

  If you facing the issue that the web Analytics Reports in SharePoint 2010 Central Administration is not updating data. When you go to your site > site settings > Site Web Analytics reports or Site Collection Analytics reports  You get old data as in the ribbon displayed "Data Last Updated: 12/13/2010 2:00:20 AM" Please insure that the following things are covered: Insure that Usage and Data Health Data Collection service is configured correctly. Log Collection Schedule is configured correctly Microsoft Sharepoint Foundation Usage Data Import and Microsoft SharePoint Foundation Usage Data Processing Timer jobs are configured to run at regular intervals One last important Timer job is the Web Analytics Trigger Workflows Timer Job insure that this timer job is enabled and scheduled to run at regular intervals (for each site that you need analytics for). After you have insured that the web analytics service configuration is working fine and the Usage Data Import job is importing the *.usage files from the ULS LOGS folder into the WSS_Logging database, and that all the required timer jobs are running as expected… wait for a day for the report to get updated… the report gets updated automatically at 2:00 am in the morning… and i could not find a way to control the schedule for this report update job. So be sure to wait for a day before giving up :)

  Read the article

• Removing 301 redirect from site root

  - by Jon Clements

  I'm having a look at a friends website (a fairly old PHP based one) which they've been advised needs re-structuring. The key points being: URLs should be lower case and more "friendly". The root of the domain should be not be re-directed. The first point I'm happy with (and the URLs needed tidying up anyway) and have a draft plan of action, however the second is baffling me as to not only the best way to do it, but also whether it should be done. Currently http://www.example.com/ is redirected to http://www.example.com/some-link-with-keywords/ using the follow index.php in the root of the Apache2 instance. <?php $nextpage = "some-link-with-keywords/"; header( "HTTP/1.1 301 Moved Permanently" ); header( "Status: 301 Moved Permanently" ); header("Location: $nextpage"); exit(0); // This is Optional but suggested, to avoid any accidental output ?> As far as I'm aware, this has been the case for around three years -- and I'm sorely tempted to advise to not worry about it. It would appear taking off the 301 could: Potentially affect page ranking (as the 'homepage' would disappear - although it couldn't disappear because of the next point...) Introduce maintainance issues as existing users would still have the re-directed page in their cache Following the above, introduce duplicate content Confuse Google/other SE's as to what the homepage actually is now I may be over-analysing this but I have a feeling it's not as simple as removing the 301 from the root, and 301'ing the previous target to the root... Any suggestions (including it's not worth it) are sincerely appreciated.

  Read the article

• How do I find a programming internship / practice?

  - by user828584

  I'm taking the SAT soon, and quickly heading toward the chaos of figuring out which college's I will be able to attend, and how on Earth I'll be able to afford it. I would like to be able to gain some experience in programming or web development, but I don't know where to look. I've been trying my best to learn over the past year, and have been doing alright in C# and the web languages (HTML, PHP, CSS, javascript). I have no idea where to look though. I've asked similar questions and rummaged through old questions on here, and they all say nothing specifically. The main two points are always "Contribute to open source projects" and "Find a company and ask to be a part of it." I don't know how to find either of the two. I've looked online at github and source forge, and the like, but all the projects are already so progressed and I just don't have the experience needed to bring myself up to speed with their code. I don't have much experience in code management, and I don't know how to get it. I would be ecstatic to be able to start a project with a group of more experienced members, but, like I said, I have no clue how to find these people.

  Read the article

• What is the best way to track / record the current programming project you work on? [duplicate]

  - by user2424160

  This question already has an answer here: Methodology for Documenting Existing Code Base 6 answers When do you start documenting the code? 13 answers Where should a programmer explain the extended logic behind the code? 5 answers I have been in this problem for long time and I want to know how it's done in real / big companies project? Suppose I have the project to build a website. Now I divide the project into sub tasks and do it. But you know that suppose I have task1 in hand like export the page to pdf. Now I spend 3 days to do that , came across various problems, many Stack Overflow questions and in the end I solve it. Now 4 months after someone told me that there is some error in the code. Now by that I completely forgot about (60%) of how I did it and why I do this way. I document the code but I can't write the whole story of that in the code. Then I have to spend much time on code to find what was the problem so that I added this line etc. I want to know that is there any way that i can log steps in completing the project. So that I can see how I end up with code, what errors I got, what questions I asked on SO and etc. How people do it in real time? Which software to use? I know in our project management software called JIRA we have tasks but that does not cover what steps I took to solve that tasks. What is the best way so that when I look back at my 2 year old project, I know how I solve particular task?

  Read the article

• Java ME SDK 3.0.5 Integrated with NetBeans 7.1.1

  - by SungmoonCho

  NetBeans 7.1.1 now integrates Java ME SDK 3.0.5, so you do not have to download them separately. Java ME SDK was packaged in NetBeans Mobility Pack, a mobile application development toolkit for NetBeans. Therefore, Java ME SDK is no longer a separate menu on NetBeans. For those who have not downloaded Java ME SDK yet, please simply visit NetBeans website and download the latest version. For those who already have Java ME SDK integrated with NetBeans 7.1 or earlier, and want to update NetBeans IDE to 7.1.1, don't worry. They can co-exist. To use NetBeans plug-ins such as Device Selector, profiler, and Internationalization Resource Manager, you have to install "Java ME SDK Tools" from NetBeans. Here is how. 1.  Go to "Tools - Plug-ins" from NetBeans menu. You can find all the plug-ins you can install into NetBeans. Locate "Java ME SDK Tools" from the list. 2. Follow the instruction to install Java ME SDK Plug-ins. 3. Once completed, you will see new menu options. For example, you can find Device Selector under Tools - Java ME. (If you used old version of Java ME, you will notice that there is not 'Java ME' menu any more. This is because all the sub-menus were integrated into appropriate places in NetBeans.) There is one thing to keep in mind; Since NetBeans 7.1.1 already includes Java ME SDK 3.0.5 and Java ME SDK 3.0.5 plug-ins must be installed through NetBeans plug-in menu, you should not download Java ME SDK 3.0.5 separately and try to integrate it with NetBeans. This may cause issues.

  Read the article

• Strategy for backwards compatibility of persistent storage

  - by Baqueta

  In my experience, trying to ensure that new versions of an application retain compatibility with data storage from previous versions can often be a painful process. What I currently do is to save a version number for each 'unit' of data (be it a file, database row/table, or whatever) and ensure that the version number gets updated each time the data changes in some way. I also create methods to convert from v1 to v2, v2 to v3, and so on. That way, if I'm at v7 and I encounter a v3 file, I can do v3-v4-v5-v6-v7. So far this approach seems to be working out well, but I haven't had to make use of it extensively yet so there may be unforseen problems. I'm also concerned that if the objects I'm loading change significantly, I'll either have to keep around old versions of the classes or face updating all my conversion methods to handle the new class definition. Is my approach sound? Are there other/better approaches I could be using? Are there any design patterns applicable to this problem?

  Read the article

• Ubuntu 10.04 LTS Server - fresh install - failed apt-get update

  - by user87227

  Good day and greetings to all, I just did a fresh installation of Ubuntu 10.04 LTS server without any issues. However, the apt-get update or aptitude update is giving the following errors: a. bzip2:(stdin) is not bzip2 file.ign for all lines plus the following errors : etched 3,582B in 0s (74.1kB/s) Reading package lists... W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used.GPG error: //security.ubuntu.com lucid-security Release: The following signatures were invalid: NODATA 1 NODATA 2 W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used.GPG error: //in.archive.ubuntu.com lucid Release: The following signatures were invalid: NODATA 1 NODATA 2 W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used.GPG error: in.archive.ubuntu.com lucid-updates Release: The following signatures were invalid: NODATA 1 NODATA 2 W: Failed to fetch security.ubuntu.com/ubuntu/dists/lucid-security/Release W: Failed to fetch in.archive.ubuntu.com/ubuntu/dists/lucid/Release W: Failed to fetch in.archive.ubuntu.com/ubuntu/dists/lucid-updates/Release W: Some index files failed to download, they have been ignored, or old ones used instead. Please guide in resolving this error. TIA Regards Venu

  Read the article

• Ubuntu Lenove OCZ Agility3 - No Grub after install

  - by Michael

  I've tried a dualboot (Win7 + Ubuntu) installation it on a Lenovo E330 with Agility3 240 Gigs... Conclusions: Ubuntu:: Ubuntu 12.04 x86_64 ( 21.06.2012 ) is not able to install grub in a bootable way. Grub will be installed and does update-grub during Installation, recognizes also the Win OS. But after a restart it boots directly to Windows.This is directly connected to the OCZ Agility3. On a good old fashion harddisk (those with the moving parts) Ubuntu is capable to install grub with no problem in a bootable manner. PinguyOS:: PinguyOS 12.04 LTS x86_64 (which is a Ubuntu based distro) is able to handle the Grub installation on OCZ Agility3. However they both use Grub 1.99... What i did:: Installed Windows. Installed Ubuntu. Installed PinguyOS. Grub Updates:: Grub updates are only through Pinguy OS possible, this means you have to edit the Ubuntu Grub entries manually after Kernelupdates on Ubuntu, in the PiguyOS sytem.. What i've already tried: Firmwareupgrade OCZ (livestick, successfull) Install Ubuntu Grub to sda Install Ubuntu Grub to sdc (Ubuntu Partion) Install Ubuntu Grub to /boot update-grub manually after install restore grub any ideas appreciated..

  Read the article

• What are the most commonly used and basic Apache htaccess redirects?

  - by bybe

  This question is here so we can offer users who are looking for information on how to make one or more common or basic redirects in Apache using the htaccess file. All future questions pertaining to finding information that is that is covered by the question should be closed as a duplication of this question. As per this Meta question. Whats the point in this question? The idea while not perfect is catch the most commonly asked questions regarding redirects using the htaccess on the Apache platform either on some type of lamp or a live server. The type of answers should be generally those that you could imagine are used by 100,000’s of sites world-wide and are constantly asked here at Pro Webmasters repeatedly over and over in various forms. A few examples of the type of answers we are looking for: How can I redirect non-www to www? How can I redirect a sub domain to the main domain? How can I redirect a sub folder from domain to a root or a subdomain? How can I redirect an old URL to a new URL? A few examples of the types of answers that we are not looking for: Answers that do not involve a redirect. Any answers relating to NGinx, IIS or any other non-Apache platform. Answers that involve custom and complex string or query removals. Resources for Advanced to Complex Mod_Rewrite Rules: Everything you ever wanted to know about mod rewrite rules but were afraid to ask Please note: that this question is still in construction and may need some refining either by myself or a real moderator of Pro Webmasters, if you have any concerns or questions please use the meta page I made a few days back here.

  Read the article

• Intel graphic chipset and NVIDIA Geforce GTX560

  - by antoine

  I have an NVIDIA Geforce GTX560 with two video projectors and I would like to use the onboard Intel Graphic Chipset to plug an additional monitor. I saw the question : How can I use both Intel onboard and Nvidia graphics at the same time? but the answer is so short that I was not convinced. My motherboard (GIGABYTE GA-H61M-D2P-B3 (rev. 1.0)) equipped with Intel H61 Chipset allow shared memory between onboard and PCIe cards. And Windows 7 allow me to use the three outputs thanks to Intel's driver. I'm able to use the onboard graphic card but without graphical interface for now. I think i need intel driver for that. But I would like to know if I can setup my displays in xorg.conf with something like : Section "Device" Identifier "Device0" Driver "intel" EndSection Section "Device" Identifier "Device1" Driver "nvidia" EndSection Section "Device" Identifier "Device2" Driver "nvidia" EndSection Does anyone have successfully setup something like that ? Or should I burn my head experimenting it by myself ? Or is there any good reasons to discouraged me to try ? Thanks for your help. Antoine PS : i'm using Ubuntu 10.10 for now, but I could switch to another version. PS2 : i also read this : Use 3 monitors w/built-in intel adapter + two old nvidia PCI cards on 10.10? which doesn't tell me more about the possibilities to use Intel Graphic and Nvidia at the same time EDIT : according to that : Can not get Dual Monitors to work on Different GPUs, I should be able to run two Xserver one on Intel the other on Nvidia. I will try and post the result here.

  Read the article

• What is the advantage to using a factor of 1024 instead of 1000 for disk size units?

  - by Joe Z.

  When considering the disk space of a storage medium, normally the computer or operating system will represent it in terms of powers of 1024 - a kilobyte is 1,024 bytes, a megabyte is 1,048,576 bytes, a gigabyte is 1,073,741,824 bytes, and so on. But I don't see any practical reason why this convention was adopted. Usually when disk size is represented in kilo-, mega-, or giga-bytes, it has to be converted into decimal first. In places where a power-of-two byte count actually matters (like the block size on a file system), the size is given in bytes anyway (e.g. 4096 bytes). Was it just a little aesthetic novelty that computer makers decided to adopt, but storage medium vendors decided to disregard? Whenever you buy a hard drive, there's always a disclaimer nowadays that says "One gigabyte means one billion bytes". It would feel like using the binary definition of "gigabyte" would artificially inflate the byte count of a device, making drive-makers have to pack 1.1 terabytes into a drive in order to have it show up as "1 TB", or to simply pack 1 terabyte in and have it show up as "931 GB" (and most of them do the latter). Some people have decided to use units like "KiB" or "MiB" in favour of "KB" and "MB" in order to distinguish the two. But is there any merit to the binary prefixes in the first place? There's probably a bit of old history I'm not aware of on this topic, and if there is, I'm looking for somebody to explain it. (Apologies if this is in the wrong place. I felt that a question on best practice might belong here, but I have faith that it will be migrated to the right place if it's incorrect.)

  Read the article

• Can no longer boot with rEFIt and Grub on early 2006 MacBook Pro

  - by Don Quixote

  I don't know what happened to cause this. I have Snow Leopard, Ubuntu 11.04 Natty Narwhal and Windows XP SP3 on my early 2006 MacBook Pro. It is a Core Duo unit, NOT Core 2 Duo, so it is 32-bit only - Model Identifier MacBookPro1,1. I use rEFIt 0.14 for my boot menu. For some reason neither XP nor Ubuntu would boot anymore. I'd just get a black screen with a rapidly flashing underscore in the top-left corner. Having both those OSes failing to boot suggested a problem with the boot loader in my MBR. The rEFIT partition tool verified that my MBR partitions were still synced with my GPT partitions, so I rewrote my MBR partition table with fdisk while booted from Parted Magic: # fdisk /dev/sda (fdisk warns about the disk having a GPT. I press on anyway.) p (Print the existing partition table to make sure it's OK.) w (Write the old partition table back to disk. This also writes a new MBR boot loader.) After this XP would boot but Ubuntu would not, with the same symptom. Now I used update-grub while chrooted into Ubuntu from Parted Magic: # mount /dev/sda3 /mnt # mount --bind /dev /mnt/dev # mount --bind /sys /mnt/sys # mount --bind /proc /mnt/proc # chroot /mnt Chroot issues some warnings about not being able to identify some group IDs. I don't know why that happens, or whether it is a problem. At this point while I am still booted off of Parted Magic's kernel, I am running from Natty's filesystem. # update-grub Update-grub detects each of my operating systems then claims to complete successfully, but still won't boot. I asked this same question over at rEFIt's Sourceforge support forum but there have been no replies yet. I also Googled quite a bit, and see many who have the same black screen problem, but none of their situations seem quite like mine. Thanks for any help you can give me. -- Don Quixote

  Read the article

• Failed to download repository information (Maveric)

  - by Rhiannon

  I have been through most of the duplicates for this question, and still can't find an answer. I may have missed one but hopefully this isn't a duplicate! Having a problem with updates. I get the "failed to download..."message followed by "Check your internet connection", which is clearing working fine as I am on it now. I click details and get the following **W:Failed to fetch http://archive.ubuntu.com/ubuntu/dists/maverick-updates/multiverse/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http://archive.ubuntu.com/ubuntu/dists/maverick-updates/universe/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-updates/multiverse/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-updates/universe/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/multiverse/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/universe/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/multiverse/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/universe/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , E:Some index files failed to download. They have been ignored, or old ones used instead.** All the faults have "maveric" somewhere in them, so I have gone to settings and unticked all the Mavarics I can find, but this problem is still happening. Any ideas? Many thanks

  Read the article

• 1.5 TB USB Drive failed to mount

  - by user89348

  Seagate 1.5Tb FreeAgent USB Hard Drive. Formatted FAT32. I figure it is 75% full. Used to work fine in XUBUNTU it shows up in Cairo Dock but when I click on it I get "failed to mount drive'. Nautilus does not display the icon nor does Thunar. Windows Vista will no longer recognise drive either. Back Track 5R3 also no longer fails to mount it. BUT and here is the BIG BUT my Pioneer DV-410 reads the files and plays the everything just fine. I believe this all happened after an unclean shutdown / XUbuntu 12.10 system freeze. Why can't XUBUNTU mount this drive when a crappy 13 year old DVD player can mount it. I am desperate to back up the data before just in case the drive becomes completely unreadable. Using XUBUNTU 12.10 Quantal current 3.5.0.17 Kernel (past 3 Kernels wont read it either) and all newest apt-get update / dist-upgrade are applied. I will post any other info you folks request as needed. Additional info as requested by githlar. $ sudo fsck.vfat /dev/sdb dosfsck 3.0.13, 30 Jun 2012, FAT32, LFN Read 512 bytes at 0:Input/output error $ lsusb Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter Bus 002 Device 002: ID 0bc2:3001 Seagate RSS LLC Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Boot existing ubuntu installation on uefi, GPT BTRFS

  - by user204720

  I have looked through many of the questions, and haven't found anything that quite satisfies this problem. I have an ssd hard drive that is bootable from my old computer. It is a standard BIOS, however, I built a new computer with Z87 motherboard that is a UEFI. What I'd like to do is boot from this hard drive without wiping out the hard drive. I've tried booting from legacy mode, doesn't seem to work. Part of the multitude of problems is my partitioning scheme, which is GPT. sdx1 is the btrfs system, sdx2 swap, sdx3 is bios_grub. I've tried setting the UEFI/BIOS to boot in legacy mode, I've tried turning my swap partition into a Grub EFI boot, I've tried copying the file system onto a new drive installed on the new system. However, copying the information doesn't keep the filesystem or subvolumes intact. I've also tried boot-repair which is when I overwrote the swap space. I'd really rather not start over on a new install, so any other suggested trees to bark up would be appreciated. For the record, I hate you Microsoft, and ASUS I understand complying with microsoft, but make it optional... I'm really disappointed in that I have to deal with Windows 8 when I have nothing to do with it. Something I think I could try, but would like to hear from more experienced users. Moving the sdx1 (btrfs /@/@home) partion and opening up a 100 MB partition on the beginning sectors and install efi compatible Grub2 installation. Would it work? How to move a partition?

  Read the article

• What triggered the popularity of lambda functions in modern mainstream programming languages?

  - by Giorgio

  In the last few years anonymous functions (AKA lambda functions) have become a very popular language construct and almost every major / mainstream programming language has introduced them or is planned to introduce them in an upcoming revision of the standard. Yet, anonymous functions are a very old and very well-known concept in Mathematics and Computer Science (invented by the mathematician Alonzo Church around 1936, and used by the Lisp programming language since 1958, see e.g. here). So why didn't today's mainstream programming languages (many of which originated 15 to 20 years ago) support lambda functions from the very beginning and only introduced them later? And what triggered the massive adoption of anonymous functions in the last few years? Is there some specific event, new requirement or programming technique that started this phenomenon? IMPORTANT NOTE The focus of this question is the introduction of anonymous functions in modern, main-stream (and therefore, maybe with a few exceptions, non functional) languages. Also, note that anonymous functions (blocks) are present in Smalltalk, which is not a functional language, and that normal named functions have been present even in procedural languages like C and Pascal for a long time. Please do not overgeneralize your answers by speaking about "the adoption of the functional paradigm and its benefits", because this is not the topic of the question.

  Read the article

• DPKG errors after upgrade to 12.10

  - by James Wulfe

  So I was doing fine then i upgraded my system to 12.10 and now i cant get my system to update all of its packages properly. no matter what i do, cleaning apt cache, manual install using dpkg, etc, i just cant get them to install. what is happening here and how do i fix this. if i would have thought 12.10 would be this much of a hassle i would have never upgraded..... here is a sampling of the code that returns from "apt-get -f install" Preparing to replace usb-modeswitch-data 20120120-0ubuntu1 (using .../usb-modeswitch-data_20120815-1_all.deb) ... /var/lib/dpkg/info/usb-modeswitch-data.prerm: 4: /var/lib/dpkg/info/usb-modeswitch-data.prerm: dpkg-maintscript-helper: Input/output error dpkg: warning: subprocess old pre-removal script returned error exit status 2 dpkg: trying script from the new package instead ... /var/lib/dpkg/tmp.ci/prerm: 4: /var/lib/dpkg/tmp.ci/prerm: dpkg-maintscript-helper: Input/output error dpkg: error processing /var/cache/apt/archives/usb-modeswitch-data_20120815-1_all.deb (--unpack): subprocess new pre-removal script returned error exit status 2 /var/lib/dpkg/info/usb-modeswitch-data.postinst: 7: /var/lib/dpkg/info/usb-modeswitch-data.postinst: dpkg-maintscript-helper: Input/output error dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: /var/cache/apt/archives/network-manager_0.9.6.0-0ubuntu7_i386.deb /var/cache/apt/archives/pcmciautils_018-8_i386.deb /var/cache/apt/archives/unity-common_6.10.0-0ubuntu2_all.deb /var/cache/apt/archives/whoopsie_0.2.7_i386.deb /var/cache/apt/archives/usb-modeswitch_1.2.3+repack0-1ubuntu3_i386.deb /var/cache/apt/archives/usb-modeswitch-data_20120815-1_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) It is also just these 6 packages only. no other packages have given me this kind of trouble. well i should say as of now. It was just 5, but them i got an update for unity, and now unity-common is added to the trouble makers. which prevents me from further upgrading the actual unity package as this package is a dependancy.....

  Read the article

• Transitioning from a mechanical engineer to software developer. What path to take?

  - by Patrick

  Hi all, I am 24 years old and have a BS in mechanical engineering from Mizzou. I have been working as a mechanical engineer in a big corporation for about 2 years since graduation. In this time, I have decided that I'm just not that interested in mechanical engineering topics, and I'm much more excited about web technology, website design, etc. I do a very small amount of freelance web design just to get experience, but I have no formal training yet. Ultimately I could see myself being very excited about working for a small startup in web technology, or creating and selling my own programs in more of an entrepreneurial role. What path do you recommend for transitioning into this field? Go back to school and get a BS in CS? MS in CS? Tech school for classes? Self study? I'm feeling overwhelmed by the options available, but the one thing I know for sure is that I'm excited to make a change. Thanks!

  Read the article

• Problems with Maverick upgrade

  - by altenuta

  I upgraded to Maverick 10.10 from Lucid. I have an old Toshiba Satellite with a 1.1 MHz and 256MB RAM. Initially I couldn't get my wireless to work. That solved itself after installing various updates and programs. The problems that remain are: I have to authorize at least 2 times at start-up. This machine is Ubuntu only. No boot load screen. I have a ton of programs and system directories that are in my home folder. Is this normal? It is difficult to wake the computer from sleep. Usually I just shut it down and restart. Tonight I waited and got a message about corrupt memory. The computer takes forever to do just about everything. Slow to start programs or doing things on the web. I am a longtime Mac user (since 1986). I also manage a network of several windoze machines. I am definitely a GUI guy and do very little in the terminal so I really need to know where to begin to get things straightened out. Can I rescue this machine without wiping it and doing a fresh install? This is basically a hobby machine. Aside from all the programs and upgrades I've installed, I have almost no files or documents to worry about saving. Anyone have any ideas about the problems I'm having and the best way to proceed? Thanks, Al

  Read the article

• How to dissuade a customer who just learned a technology and wants to use it everywhere?

  - by MainMa

  My customer recently discovered what is URL Rewriting, without completely understanding what it is, how it works and the pros and cons of it. Now, he asks for lots of strange changes in actual requirements of current projects and changes in old projects in order to implement what he believes is URL Rewriting. On one hand, I'm annoyed being asked to do things which doesn't make any sense instead of doing real work. On the other hand, I can't tell my customer that he doesn't understand anything in the subject despite his interest in it. I think many people have had situations when their manager or their customer just learned a new buzzword or a new technology, and he loved it so much than he wanted to use it in every project, everywhere, rewrite the whole codebase just to use this new thing, etc. Also, I've recently read something related on Programmers.SE where people told about their experiences when there was a huge buzz around XML, and some managers would ask to introduce XML in every project just to show to everyone that they have used it. So those who have been in similar situation, how have you managed it?

  Read the article

• How to create an Orthographic display in OpenGL (ES) that handles different screen sizes and orientations?

  - by Piku

  I'm trying to create an iPad/iPhone game using GLES2.0 that contains a 3D scene with a heads-up-display/GUI overlaid on the top. However, this problem would also apply if I were to port my game to a computer and run the game in a resizable window, or allow the user to change screen resolutions... When trying to make the 2D GUI/HUD work I've made the assumption that all I'm really doing is drawing a load of 2D textured 'quads' on the screen and am trying to treat the orthographic projection as an old-style 2D display with 0,0 in the upper left and screenWidth,ScreenHeight in the lower right. This causes me all sorts of confusion when I rotate my ipad into Landscape mode since I can't work out what to put into my projection and modelview matrices to turn everything around the right way. It also gets messy if I want to support the iPad's large screen, an iPhone or a Retina display since I have to then draw three sets of textures for everything and work out which ones to use. Should I be trying to map the 2D OpenGL co-ords 1:1 with the screen? While typing out this question it occurs to me that I could keep my origin in the centre, still running -1/+1 along the axes. This would let me scale my 2D content appropriately on the different screen sizes, but wouldn't I end up with the textures being scaled and possibly losing quality? I'm using OpenGLES 2.0 and have a matrix library that has equivalents to the GLES1.1 glOrthof() and glFrustrum() calls.

  Read the article

• Rotate canvas along its center based on user touch - Android

  - by Ganapathy

  I want to rotate the canvas circularly on its center axis based on user touch. i want to rotate based on center but its rotating based on top left corner . so i am able to see only 1/4 for rotation of image. any idea.. Like a old phone dialer . I have tried like as follows onDraw(Canvas canvas){ canvas.save(); // do my rotation canvas.rotate(rotation,0,0); canvas.drawBitmap( ((BitmapDrawable)d).getBitmap(),0,0,p ); canvas.restore(); } @Override public boolean onTouchEvent(MotionEvent e) { float x = e.getX(); float y = e.getY(); updateRotation(x,y); mPreviousX = x; mPreviousY = y; invalidate(); } private void updateRotation(float x, float y) { double r = Math.atan2(x - centerX, centerY - y); rotation = (int) Math.toDegrees(r); }

  Read the article

• Sudden drop in Total Indexed pages and increase in 'Not Selected' number.

  - by Pravin

  My blog is around 1 year old and have PR2. The average daily pageviews upto last 1 week were 1800. The total number of posts are 180. Though I have only 180 total posts, the total number of Indexed URL was increasing and it was as high as 510. But in the month of Sept2012, the total number of Indexed pages dropped from 510 to 214. The drop was sudden and it is now increasing very slowly. Also, the other main concern is huge increase in 'Not Selected' number. It is currently 814. I have never posted any post again and never copied any idea from any other blog. But I do use internal linking to some older post those are related to the new posts. The questions are:; Why there is sudden drop in the 'Total Indexed' pages. Why there was increase in total indexed pages to 500 even though the total posts were only 180. As the drop in 'Total Indexed' was in the month of sept2012, I was getting same organic traffic and it was steadily increasing till last week and then there was a 50 drop in the total pageviews. Why. Now, again the traffic is becoming to normal but still there is a problem. Is increase in the 'Not selected' number is a cause of drop in 'Total Indexed'? How to prevent or reduce the number of 'Not Selected' even though I do not have any duplicate post withing blog. Is the 'internal linking' to older post creating 'Not selected' problem? Should I edit my 'Robot.txt' to avoid crawling of labes that may be creating duplicate posts or something like that, if so, what is correct robot.txt. I have uploaded the screenshot of the graph of Webmaster Tools. Please take a look and give suggestions. Please help. Thank you in advance.

  Read the article

• What You Said: How You Find New Books

  - by Jason Fitzpatrick

  Earlier this week we asked you to share your tips and tricks for finding fresh books to enjoy. Now we’re back with tips ranging from the old school to the digital. SJ highlights several of the most popular web-based tools for finding new books: Goodreads.com is quick and easy. Yournextread.com is fun and helps a lot. But I gotta be honest, Amazon’s suggestions are probably the most useful to me. TheFu suggests checking out award-winning lists and one rather quirky way to pick a good Sci-Fi book: For scifi, see Hugo winning books. Life is too short to read bad books. Sometimes that leads to an author with an entire series of books to enjoy. I really enjoy some of the scifi from the 40s and 50s. Wells stuff is always timeless too (and free). I’m less happy with Nebula winners–-different type of writers and not my personal taste. Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

  Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >