Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 278/1617 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

  • dhcp client service won't start

    - by xyious
    I have a Laptop with 2 network interfaces and neither will get an IP address through dhcp. I found out that the dhcp client service didn't start. Upon manually starting it gives the error 2: File not found. I have checked that the files were there (both svchost and dhcpcore .dll), the local service account has read access to the system32 folder, the path in the registry is also correct and I can access the file. I have tried to netsh winsock reset and ip reset all. I have even added the local service account to the administrators group. sfc /scannow also came up clean. I have no idea what else I can try. Any suggestions are welcome. (side note it's a windows 7 32 bit, atheros wlan, deinstalled avira before any of the other troubleshooting)

    Read the article

  • What is your approach to draw a representation of your network ?

    - by Kartoch
    Hello, I'm looking to the community to see how people are drawing their networks, i.e. using symbols to represent complex topology. You can have hardware approach, where every hardware unit are represented. You can also have "entity" approach, where each "service" is shown. Both are interesting but it is difficult to have both on the same schema (but this is needed, especially using virtualization environment). Furthermore, it is difficult to have complex informations on such representation. For instance security parameters (encrypted link, need for authentication) or specific details (protocol type, ports, encapsulation). So my question is: where your are drawing a representation of your network, what is your approach ? Are you using methodology and/or specific softwares ? What is your recommendations for information to put (or not) ? How to deal with the complexity when the network becomes large and/or you want to put a lot of information on it ? Examples and links to good references will be appreciated.

    Read the article

  • Multiple network cards, controlling where my traffic goes

    - by thefinn93
    This is an Ubuntu 12.04 server install. I have multiple network cards, eth0 and eth1 lets call them. eth0 is connected to the internet, and all of my traffic goes through it, until eth1 gets plugged in. Then the machine tries to send everything through eth1, which for various and sundry reasons does not go out to the Interent. The only traffic it doesn't send through eth1 is traffic on eth0's subnet. It also will not accept inbound connections on eth0 from outside of eth0's subnet. I'd like all outbound traffic to go out eth0, but I'd like incoming connections from to either card from any subnet to work.

    Read the article

  • Network bandwidth usage dashboard?

    - by SkippyFlipjack
    I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

    Read the article

  • Is it better to use a crowded 2.4GHz Wi-Fi channel 1, 6, 11 or "unused" 3, 4, 8, or 9?

    - by Luke
    I understand that 2.4GHz Wi-Fi channels overlap, and that the only non-overlapping channels in the US are 1, 6, and 11. Generally, my signal strength on channels 1, 6, and 11 are much stronger than my neighbors' on the same channel. However, several of the channels may have 4 or 5 others on that same channel. In this scenario, is it better to use 3, 4, 8, or 9? Or is it better to use the crowded channels 1, 6, and 11? As a secondary question, does it even matter that my signal strength is much higher than theirs? Related: Why use wifi channels other than 1, 6 or 11?

    Read the article

  • Windows Server 2003 Is there a limit on number of TCP connections per process?

    - by aceinthehole
    We are running into issues with BizTalk host instance intermittently going down. One of the things that we are worried about is the number of FTP connections a single host instance is making which could easily reach into the hundreds perhaps sometimes thousands, depending on traffic. My question is Windows Server 2003 Is there a limit on number of TCP connections per process? If so would putting each application in it's own host instance potentially solve the problem.

    Read the article

  • Host data transfer limit calculations and network protocol headers

    - by UpTheCreek
    OK, this might be a really stupid question, but... I'm building a web app that utilises websockets. There's fairly rapid messaging going on, so I've been taking a look at the network traffic with wireshark, to see if there's any way of reducing the amount of data we are sending over the wire, and hence costs. A typical message has approx 150 byte data payload, and according to wireshark the lower layer stuff takes up about: Ethernet: 14 bytes IP: 20 Bytes TCP: 20 Bytes My question is, are these network headers included in data transfer calculations? What about TCP ACK messages? (another 54 bytes according to wireshark) This may seem petty, but because we have so much messaging going on, and because the payload is a similar size to these headers, it's significant.

    Read the article

  • Samba+Windows: Allow multiple connections by different users?

    - by rgoytacaz
    Hello there, I have a machine running Ubuntu with Samba that I use to share stuff with my family's Windows machines in our local network. Currently they access a share for movies/music/etc with one user. I want to connect them to another share as a different user (for example, user "goytacaz"). When I try connecting to this new share, Windows gives me "Error 1219" and complains about multiple connections by the same user. How do I get my machine to accept multiple connections by the same user?

    Read the article

  • ssh can't connect after server ip changed

    - by Kery
    I have a server with ubuntu installed. After I change the network configuration and restart server, ssh client can't connect server any more. But in the server I can use ssh client to connect itself and the netstat command shows that sshd is listening port 22. And in my computer (win7) ping command is OK to server's new IP. The configuration in /etc/network/interfaces is: auto eth0 iface eth0 inet static address 10.80.x.x netmask 255.255.255.0 gateway 10.80.x.1 I'm very confused about this. Hope somebody can give me some idea. Thank you in advance!!!

    Read the article

  • Selectively routing traffic via ethernet or wifi, with proper DNS (Mac OS X 10.6)

    - by Dan
    When I'm at work, I access various intranet pages as well as the wider Internet through ethernet. However, the company LAN blocks some ports (e.g. Google Calendar). I can get to those through WiFi. So, I gave the Airport priority, and then using route add, I set up selective routing: all intranet traffic goes through the ethernet and everything else via WiFi: sudo route add 10.0.0.0/8 <intranet gateway>. However, there are a number of intranet sites that have their own DNS; i.e., hr.company.com only resolves on the intranet. The only way that I can get the DNS to work properly is to add the internal DNS server to the Airport DNS listing, however I fear that when I go elsewhere and forget, this will break things. What's the right way to get the DNS to resolve using this setup?

    Read the article

  • Can I make Windows behave like an ethernet hub?

    - by dromedary
    I have two machines A and C mutually connected to NICs on a third machine, B, as follows: A-B-C B is a Windows 7 machine configured with a bridge containing the A-B and B-C NICs, so that A and C can communicate. So far, so good. I need frames from A destined for B to also arrive at C. Essentially, I would like Windows to behave like a hub rather than a switch. Is there any way to do this? If you have any ideas at all, no matter how hacky or roundabout, I would love to hear from you! I have been tearing my hair out over this and by now I am willing to try anything. My only limitations are that I can't touch A or change to a different operating system on B.

    Read the article

  • Outbound ports to allow through firewall

    - by dunxd
    This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support commonly required resources: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working. I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

    Read the article

  • VM connected to network but not to internet in VMware Player 6 on Windows 8.1 host

    - by user1257262
    So I am running Bitnami's MEAN stack in VMware Player 6.0.2 on Windows 8.1 and the VM connects just fine to the network: https://www.dropbox.com/s/xfdzohjuuepz52w/ifconfig.PNG However, I am having a great deal of trouble getting the VM to communicate with the internet. No matter what sort of action I take (even something as simple as apt-get update), the machine just sits there and eventually fails to connect. Here is my VM's Network Adapter configuration: https://www.dropbox.com/s/xfdzohjuuepz52w/ifconfig.PNG On my host Windows 8.1 computer, I actually have the VMware Bridge Protocol enabled but for VMware Network Adapters (VMnet1 and VMnet 8), but they are listed as having No Internet access in my Network and Sharing Center. I am not entirely sure if these adapters are relevant to connecting the VM to the internet, to be honest. This is the first time I have ever had an issue connecting a virtual machine to the internet. This problem is also happening with other VM's I am trying to run. Can someone tell me what I am doing wrong and how I can fix it?

    Read the article

  • How to setup THIS IPv6 network

    - by Revolter
    I have a network mapped like this : just to experiment IPv6 connectivity, i want to configure my LAN network using IPv6, can some one explain me how to convert the connection between the Desktop and the Laptop to IPv6 without loosing the internet connection ? I don't want to access IPv6 internet, I need to keep my v4. So the end result will be something like an full-IPv6 Laptop accesing IPv4 internet over a some-how-configured Desktop that acting as a NAT.

    Read the article

  • How to setup an Openvpn server with two gateways to internet

    - by fourat
    I have an openvpn server behind two wan interfaces: eth1 and eth2 where eth1 is the default gw and eth2 is where openvpn binds to. The problems my ovpn server is replying back to ovpn client via the default gw (through eth1) and the tcp negociation is lost before establishing any tunnel. Here's what's happening: wan client -----> eth2 ----> openvpn -----> eth1 ----> lost and not delivered back to client Is there a way to tell ovpn to stick on eth2 and consider it for all traffic ?

    Read the article

  • how to switch played music when someone enters

    - by ymajoros
    My wife has a small shop, and she plays free licensed music. She can't legally play her own music when people outside of the family circle are present in the shop. How can I automatically switch music when someone enters? I was thinking of some bluetooth door detector and some custom software, but can't seem to find either. I'm a software architect/dev and can write it if necessary, but I'd prefer to use some existing solution. Any ideas on good hardware and software for this?

    Read the article

  • How to stop my wireless adapter from received dhcp from router (windows)

    - by baobeiii
    Hi, I have a windows 7 computer which is connected via vpn to an OpenVpn server which happens to be in another country. I have all internet traffic being routed from my computer through the vpn to the server. However dns queries are not going through the vpn, but are instead going directly to my isp's dns via a route outside of the vpn tunnel. This is happening because my wireless adapter is configured to obtain DNS server address automatically. The router that stands between my computer and the internet happens to have a DCHP server running on it that is assinging my computer with the DNS addresses of the isp. The issue is, i haven't been able to stop my wireless adapter on my computer from receiving the dns settings from the router. I've tried selecting 'use the following dns server addresses' and then just leaving them blank, but ipconfig /all shows me that this hasn't worked and i'm still getting dns form the router. So is there any way to completely stop my windows wireless adapter from receiving these settings from the router? I have the OpenVpn server pushing to my computer's tun adapter the dns that it should be using. I'd rather solve this in a way that doesn't involve disabling the dhcp server on the router or fiddling with the router. The reason is i'm on a laptop and i want my vpn to not leak dns even when i'm out, for example in wireless hotspots. I know if i could just force the wireless adapter to ignore the router's dhcp server then my dns queries would go through the tunnel to the dns address pushed by the OpenVpn server. Sorry, i know thats long winded, if you have any idea's please do tell me. Thanks and merry xmas.

    Read the article

  • How to change the setting for a network device reported by ethtool, specifically Speed, on VM?

    - by Ramadheer Singh
    This is related to these two questions, although they don't answer my question. The machines are RHEL6. 1.ethtool not showing all the properties 2.changing network speed to 1000Mb/s Output on VM: [root@foo ~]# ethtool eth0 Settings for eth0: Current message level: 0x00000007 (7) Link detected: yes Output on Real Hardware: (interested in Speed) # ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes ***Speed: 1000Mb/s*** Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: d Wake-on: d Link detected: yes if there's anyway I can set this in VM, please suggest.

    Read the article

  • Video streaming and internet browsing on different bands/frequency

    - by user47207
    I have a Netgear WDNR37000 which allows clients on a 2ghz or 5ghz to access the internet and see every client and device on the network. I have a computer with two nics, one that is in the 2ghz range and the other on the 5ghz range. My specific problem is that I would like to serve my video streams (hulu, ps3mediaserver, playon) to my ps3 on the 5ghz band while internet browsing is routed to the 2ghz band. This is so that the video streams aren't affected by general internet use. While the easiest solution would be to disable internet access on the 5ghz apn, I would like to know of a solution that would not require that.

    Read the article

  • Windows 7/8 can't connect to an N Router

    - by xenoterracide
    I have a router running OpenWRT backfire, with N and A/B/G being broadcast. A linux laptop, and a Mac laptop can see the N network and connect to it (or at least they could last weekend). But there is now a Windows 7 Desktop with a B/G/N wireless card, and a Windows 8 Laptop with a B/G/N wireless card that can't see the N network only the B/G broadcast. The B/G and N have different SSID's and Encryption ( WEP and WPA2 PSK respectively ). The N SSID isn't even visible. Does anyone have any suggestions as to how to troubleshoot further? Or what might be the cause? update wireless info Desktop Dell Wireless 1502 802.11b/g/n Atheros Communications Inc 9.2.0.412

    Read the article

  • Intranet machines refuse to talk anymore

    - by ashes999
    I have two machines on the local intranet. They used to be able to talk to each other (ping, share files, etc.). Both are not successfully connected to the internet. The problem machine (lets call it test machine) can't talk to my main machine. The test machine can ping other machines on the intranet (at least one of my coworkers), but not mine. Odd. When I try to ping it from my machine, by machine name, I get Destination host unreachable. Both machines are on the intranet, with the network configured as Work Both machines have Windows Firewall disabled temporarily Both machines can talk to the internet (Google, SO, etc.) Neither machine can ping the other I need help resolving this. What I really want to achieve, is to remote into the test machine from my main machine, like I used to be able to do a few weeks ago. Some notes: Tried arp -a on both machines. I don't see the other machine's IP listed. Both machines have stable IPs; neither seems to have an IP conflict The configuration under ipconfig /all on my main machine mathces my coworker's machine. The test machine can ping his machine, but not my machine. The target machine times out trying to ping the main machine; the main machine gives me Destination host unreachable. I have rebooted both machines (several times) to no avail I have /release and /renewed both machines several times

    Read the article

  • Iptables port mapping from two PCs to one

    - by Anton
    We have 3 PCs, two of it are connected to internet (both of it have 2 NIC) PC1: eth0 - 1.0.0.1 (external IP) eth1 - 172.16.0.1 (internal IP) PC2: eth0 - 1.0.0.2 (external IP) eth1 - 172.16.0.2 (internal IP) PC3: eth0 - 172.16.0.3 (internal IP) Now we want to map port 80 from PC1 and PC2 to PC3. But there is the problem: iptables port forwarding works well from PC1 or PC2, but only in case if PC3 have PC1 or PC2 as gateway. So, question is: can we have port mapping from both PC1 and PC2 regardless of gateway settings on PC3? Thank you in advance.

    Read the article

  • Throughput and why do ISPs sell too much bandwidth?

    - by jonescb
    I hope the question made sense how I worded it. :) I've been wondering, maximum theoretical bandwidth is measured as RWIN/RTT (Window size / round trip time) Source 1 and Souce 2 So if a major city only 100 miles away gives me a ping of 50ms, and I have the default 64kb TCP window size then my maximum throughput will be 12.5Mb/s. Everything further away would give me a higher ping and therefore a lower throughput. Is there any reason to buy something like FiOS with a 50Mb/s or greater connection? Will you ever be able to reach that kind of speed? I know you can increase the TCP window size to increase throughput, but it has to be at both ends which is a deal breaker because you can't control the server. I'm assuming other network protocols like UDP aren't quite as affected by latency as TCP is, but how much of overall network traffic does non-TCP make up vs TCP. Am I just misguided about how throughput works? But if the above is correct, then why should a consumer like me buy way more bandwidth than can be realistically used. Maybe the only reason is for downloading multiple things at once, or one thing from multiple servers/peers?

    Read the article

  • Mirror network packets from WiFi to Ethernet in an ASUS Router RT N53

    - by fazineroso
    I have an ASUS RT N53 router, running the default firmware (Linux 2.6.22 with busybox and uclibc). I need to capture data packets from some Wi-Fi devices I have connected to that router (iPad and some smartphones), but the router is not forwarding any package coming from Wi-Fi devices to the Ethernet Ports. Any idea how can I proceed? Available tools in the router are iptables (no tee option, though), ebtables, brctl... Currently the ethernet and Wifi devices are forming a bridge: # brctl show bridge name bridge id STP enabled interfaces br0 8000.50465dc06be2 no vlan0 eth1 No ebtables rules: # ebtables -L Bridge table: filter Bridge chain: INPUT, entries: 0, policy: ACCEPT Bridge chain: FORWARD, entries: 0, policy: ACCEPT Bridge chain: OUTPUT, entries: 0, policy: ACCEPT

    Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >