Search Results

Search found 14821 results on 593 pages for 'device driver'.

Page 280/593 | < Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• dd on entire disk, but do not want empty portion

  - by Jonathan Henson

  I have a disk, say /dev/sda. Here is fdisk -l: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0000e4b5 Device Boot Start End Blocks Id System /dev/sda1 * 1 27 209920 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 27 525 4000768 5 Extended Partition 2 does not end on cylinder boundary. /dev/sda5 27 353 2621440 83 Linux /dev/sda6 353 405 416768 83 Linux /dev/sda7 405 490 675840 83 Linux /dev/sda8 490 525 282624 83 Linux I need to make an image to store on our file server for use in flashing other devices we are manufacturing so I only want the used space (only about 4gb). I want to keep the mbr etc... as this device should be boot ready as soon as the copy is finished. Any ideas? I previously had been using dd if=/dev/sda of=[//fileserver/file], but at that time, my master copy was on a 4gb flash ide.

  Read the article

• Where is my problem? The P6X58D Premium Mobo, Windows 7, or other?

  - by Dylan Yaga

  I was having problems with my USB devices for an hour last night, and I am unable to determine the root cause of the problem. The two symptoms are: At seemingly random times (not consistently spaced by time or caused by any detectable event) my USB devices become "detached". Windows will play the USB disconnect sound and then the reconnect sound. The devices disconnected and then reconnected. My USB Keyboard will "stick" on one key for several seconds before processing any other keystroke made. The mouse also does not respond to clicks. I do not lose mouse movement or USB device connectivity. And after a moment of this several beeps will be emitted from the speakers. Hardware Specs: GFX Card: EVGA GeForce GTX 470 Superclocked 1280MB DDR5 PCIe Motherboard: ASUS P6X58D Premium Intel X58 Socket LGA1366 MB Processor: Intel Core i7-920 2.66Ghz 8M LGA1366 CPU Memory: Corsair Dominator 6144MB PC12800 DDR3 Storage: Hitachi 1TB Serial ATA HD 1600MHz 7200/32MB/SATA-3G Cooling: Corsair Hydro H50 CPU Liquid Cooler Case: Corsair Obsidian 800D Full Tower Case Power Supply: Corsair HX1000W 1000W Modular Power Supply Steps I have taken to narrow down the problem: Restarted the computer. - No change Changed USB port the Hub was connected to on the CPU. - No change Removed all devices from USB Hub and connected directly to CPU. - No change Used a different USB keyboard both in USB Hub and directly to CPU. - No change Disconnected and reconnected all cables. - No change Disassembled the Tower and determined if the USB headers were firmly connected. - No change Checked device manager for errors. Checked all USB devices. - Nothing flagged After an hour of frustration trying to narrow down the problem it appeared to disappear. But I am torn between it being a Mobo problem or an OS problem. Is there anything else I can do to narrow down the problem before a reformat and then eventually exchanging the Mobo?

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Dell Vostro Desktop error

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• How to set TV-out options under Linux of an Geforce 9600 GT video card

  - by polemon

  I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

  Read the article

• Unable to sync iPod Touch with my PC

  - by alex

  I'm trying to sync a first gen iPod Touch to my PC running Windows 7 64 bit. The problem is that whenever I connect the iPod, iTunes completely freezes (if I start iTunes after connecting the iPod it will simply hang until it's physically disconnected from the PC). I reinstalled iTunes thinking that it had been corrupted, but without any luck. I've had this problem with all the latest versions of iTunes. I've also tried using MediaMonkey and DoubleTwist. None of these apps see the iPod as being connected; DoubleTwist also freezes, just like iTunes. The really strange thing is that I was able to sync the iPod with this PC a while back, but I now seem to have lost that ability. I don't know what changed. Windows detects the device every time it's plugged in (I can see it in Device Manager and I can browse all photos on iPod as if it were a camera). Also, I can sync it to iTunes on Mac OS X without any major problems.

  Read the article

• How to backup a large FreeNAS?

  - by Ze'ev

  We have a 12TB FreeNAS box in the office, and are looking for a way to keep a backup of it offsite. We're considering (1) tape; (2) a bunch of bare drives (popped into a spare hotswap bay); (3) external drives. Any advice on which solution is best? (Online backup is not an option because our internet connection is too slow.) And, is there some software that will keep track of which files have been backed up and which haven't? So that when one backup unit fills up, we can continue the backup on the next? (We don't want to have to back up to a 12TB device.) This software could run, preferably, on the NAS itself; or from one of our Mac clients. Our goal is a situation where we attach some backup device; it automatically fills up with stuff from the server; the contents of this unit are catalogued somewhere something prompts us to replace with a fresh drive/tape; backup continues until full, including any files that have changed since being backed up.

  Read the article

• Boot records messed on dual boot (win7 and ubuntu) machine with SSD and HDD

  - by Michael

  i have a lenovo ideapad y570 with two hard drives: SSD and normal HDD both managed by RapidDrive and windows 7 pre-installed. First, i have shrunk my 500 GB HDD a little bit to make some place for a linux installation. Then i installed linux mint 12 to it, also installed grub onto the drive (dev/sdb). Installation programm has not allowed me to install grub on sda. Then i replaced linux mint with ubuntu 12.04 but installed grub onto the SSD (which is dev/sda and was the default-option). After that i could boot into my windows, only ubuntu worked. So i did a research, and tried: rewriting mbr of windows into sda1, reinstalling grub, replacing grub2 with grub-legacy, and now i think my partitions table are totally messed. Here is fdisk -l output: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /dev/sda2 411648 1009430959 504509656 7 HPFS/NTFS/exFAT Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5e5d1cc8 Device Boot Start End Blocks Id System /dev/sdb1 * 1979 884389887 442193954+ 12 Compaq diagnostics /dev/sdb2 884391934 976771071 46189569 5 Extended /dev/sdb5 884391936 937705471 26656768 83 Linux /dev/sdb6 937707520 967006207 14649344 83 Linux /dev/sdb7 967008256 976771071 4881408 82 Linux swap / Solaris I also cant mount any windows partitions to recover data. And when i open gparted, the whole sda-disk appears unallocated and it states "can not have a partition outside the disk!", also the end-sector address of /dev/sda2 confuses me. If i boot from the SSD, it throws some mbr error and wont boot, if i boot from the HDD, i only get the grub bash. How do i restore the partition tables? I can boot only from a live-cd at the machine. Thanks for any help.

  Read the article

• Booting an Asus EeePC from a LiveCD USB stick

  - by Bryan

  I have two identical Asus EeePC netbooks that are both installed with Ubuntu. One of them was sitting on the closet shelf and the battery went completely dead. When I charged the battery and tried to boot the it, I got the "No init found" error. In trying to follow the suggested way to fix it posted here, I used the Startup Disk Creator on my Ubuntu 11.10 desktop machine to create a USB stick with a bootable Ubuntu 11.10 live CD on it (the netbook doesn't have a CD drive). I plugged the USB stick into the netbook with the init issues, went into the BIOS and selected the USB stick as the 1st choice to boot from, and did a hard restart. It then just stuck at the flashing underscore. Not knowing why it wasn't working, I tried booting my working netbook from the USB stick. When I got into the BIOS on the working netbook, I noticed the description in the boot order section for the USB device was different. On the non-working netbook, the description was SWISSBIT (the name of the USB stick) but on the working netbook it was just "Rem. Drive". I also noticed on the working netbook there was an additional option under the bootable order section that allowed me to choose which hard drive to boot from. This section showed two hard drives, one of them being my USB stick. So, rather than changing the device boot order, I selected the USB stick as the hard drive to boot from first and it worked like a champ - I was able to boot into the LiveCD on the USB stick. Seems to me the working netbook is seeing the LiveCD USB stick as a hard drive, where-as the non-working netbook is seeing it as a plain ol' USB stick. The BIOS is the exact same version on both netbooks... any idea why it works on one and not on the other?

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• Extending ext4 partition on debian7.0 on vsphere

  - by VoidPointer

  I have allocated thin provisioning of 15GB when i found 8GB as insufficient. Now debian guest is not able to recognize the change of size. root@debian7-x64:~# lvdisplay --- Logical volume --- LV Path /dev/debian7-x64/root LV Name root VG Name debian7-x64 LV UUID EU6mg0-XTXC-ci3D-bQJi-7XN6-r8Hp-SYxcj0 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 1 LV Size 7.39 GiB Current LE 1892 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:0 --- Logical volume --- LV Path /dev/debian7-x64/swap_1 LV Name swap_1 VG Name debian7-x64 LV UUID xDNtoz-tJUq-M5D6-GGCN-gzcD-fwUv-fYYDR1 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 2 LV Size 376.00 MiB Current LE 94 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:1 root@debian7-x64:~# pvdisplay --- Physical volume --- PV Name /dev/sda5 VG Name debian7-x64 PV Size 7.76 GiB / not usable 2.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 1986 Free PE 0 Allocated PE 1986 PV UUID SehkzH-Gq8Y-jI2f-27Tb-uv1Z-tR1R-5OnTxR root@debian7-x64:~# sfdisk -s /dev/sda: 15728640 /dev/mapper/debian7--x64-root: 7749632 /dev/mapper/debian7--x64-swap_1: 385024 total: 23863296 blocks Help me to extend this partition. No problem in rebooting. I dont have any live CD. Environment : debian 7, with lvm, on vsphere, ext4 partition. Can provide more details when needed.

  Read the article

• Configuring MySQL for Power Failure

  - by Farrukh Arshad

  I have absolutely no experience with databases and MySql. Now the problem is I have an embedded device running a MySQL database with a web based application. The problem is when I shutdown my embedded device it just cut off the power, and I can not have a controlled shutdown. Given this situation how can I configure MySql to prevent it from failures and in case of a failure, I should have maximum support to recover my database. While searching this, I came across InnoDB Engine as well as some configuration options to set like sync_binlog=1 & innodb_flush_log_at_trx_commit=1. I have noticed my default Engine is InnoDB and binary logs are also enabled. What are other configurations to make for best possible failure & recovery support. Updated: I will be using InnoDB engine which supports Transactions. My question is how best I can configure it (InnoDB + MySQL) so that it can provide best possible fail-safe as well as crash recovery mechanism. One configuration option I came across is to enable binary logging which InnoDB uses at the time of recovery. Regards, Farrukh Arshad

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• Exchange 2007 with Android activesync

  - by lbanz

  A few of our users noticed that it will stop working intermittently for them. I didn't believe it at first until I changed my android phone and it started occuring for me. It will just stop syncing completely, it looks like the server is blocking the device completely. This mainly occurs when they are using the wifi. I've done some testing. If I switch off the wifi and use the phone data plan it will work fine. When it's on the wifi network, I try and browse to the webmail/owa page and it says page not found! I did a dns lookup and they resolve correctly. If I use another device on the same wifi network, it can access the exchange servers fine. Sometimes the wifi network will just work without any issues. But when it fails, it looks like the phone constantly checks the server every second to see if it is online even though I've got it on manual sync. I was wondering whether it tries to sync too many times and exchange thinks its a denial service attack. My old android phone that works is Froyo and the new one is Icecream. People who have reported issues seems to be newer phones. They also tested their own wifi network at home and experience the same problem. We haven't patch our exchange recently before seeing this problem. Anyone has seen this issue?

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Wireless keeps shutting off in Windows 7

  - by Nathan Adams

  I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

  Read the article

• ownership of hard drive recoveery of files Windows 7

  - by Jeff

  Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

  Read the article

• Dell Vostro Desktop error.

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• HTC Diamond Touch sync problem

  - by Anders

  I have a HTC Diamond Touch with all my contacts etc. on it. Did however not use it for 6mo while being abroad. When I start the phone now I realize that the touch screen has stopped working. I have tried restarting, soft resetting, shutting it off etc but the touch just wont follow commands. However, I can manage the phone by buttons so it's not frozen. Hence I can get into the phone and watch contacts but not use it to call etc. The problem is, how do I get my 300 contacts out of the thing!? When I'm plugging in the phone, it lets me choose between "Sync with Outlook" and "Use as storage device". It automatically selects "Use as storage device". Now, I cannot choose to sync it with the buttons. I can not change this option afterwards either. In short, I have a phone with all of my contact data and am completely unable to get that out of it. Any tips/help/suggestions? If possible, preferably one that does not including sending the phone to a hardware workshop for three weeks in order to get it fixed:)

  Read the article

• SATA DVD drive refuses to read movie DVDs

  - by poke

  Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

  Read the article

< Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >