Search Results

Search found 14821 results on 593 pages for 'device driver'.

Page 278/593 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• 2008 Sever Randomly reboots.

  - by Jeff

  I'm out of ideas here. We have a 2008 Server that keeps rebooting 2-3 times a day at completely random times with an "Unexpected Shutdown" event. There are no Dumps, no events leading to it just like it loses power then comes back online. I ran a Diagnostic of the power supply and it has had continuous power for months. In addition, the temperature of the processors are maxing out at 40 degrees Celsius. Anyone have any ideas how to figure out why this is restarting all the time? This is a DMZed Web server so it doesn't do too much process wise. Here are the specs: Host Name: ~~~ OS Name: Microsoft Windows Server 2008 R2 Standard OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Server OS Build Type: Multiprocessor Free Registered Owner: Windows User Registered Organization: Product ID: ~~~ Original Install Date: 5/27/2010, 4:25:47 PM System Boot Time: 2/14/2011, 5:35:01 PM System Manufacturer: HP System Model: ProLiant DL380 G6 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 26 Stepping 5 GenuineIntel ~1586 Mhz BIOS Version: HP P62, 8/16/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume1 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 4,086 MB Available Physical Memory: 2,775 MB Virtual Memory: Max Size: 8,170 MB Virtual Memory: Available: 6,691 MB Virtual Memory: In Use: 1,479 MB Page File Location(s): C:\pagefile.sys

  Read the article

• Constant beeping

  - by Bogi Juul Peterson

  My computer has a problem with beeping. I'll first tell you how it started: One night I decided to watch a cartoon, and I took some water and food with me to eat while I watch. I fell asleep and when I woke up I had spilled water all over my keyboard. I didn't react quickly, because it went unnoticed for about 1 and a half hours. When I noticed, I quickly put my laptop on a radiator to try to dry it. When I turned the computer on there was a constant beeping sound. I didn't know what caused it, and I'm still not sure, but I think it has something to do with the USB hub. If I let the computer stand for some hours without any USB connections, it's fine, but when I put any kind of USB device in, it starts beeping. The laptop keyboard doesn't work so I have to have some kind of USB device connected to use the computer. The beeping is going on while I'm writing this and it makes my computer lag so much that it can make delays from the keyboard be from 1 second to 10 seconds. I need this computer because I don't have the money to buy a new one, and I have to use this computer for homework and games. The beeping is constant, with less than a second between beeps. If anyone has a solution, please help.

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• 100% iowait + drive faults in dmesg

  - by w00t

  Hi, I have a server on which resides a fairly visited web app. It has a raid1 of 2 HDDs, 64MB Buffer, 7200 RPM. Today it started throwing out errors like: kernel: ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen kernel: ata2.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in kernel: res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) kernel: ata2.00: status: { DRDY } kernel: ata2: hard resetting link kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: configured for UDMA/133 kernel: sd 1:0:0:0: timing out command, waited 7s kernel: ata2: EH complete kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) kernel: sda: Write Protect is off kernel: SCSI device sda: drive cache: write back All day long it has been in load higher than 10-15. I am monitoring it with atop and it gives some bizarre readings: DSK | sda | busy 100% | read 2 | write 208 | KiB/r 16 | KiB/w 32 | MBr/s 0.00 | MBw/s 0.65 | avq 86.17 | avio 47.6 ms | DSK | sdb | busy 1% | read 10 | write 117 | KiB/r 17 | KiB/w 5 | MBr/s 0.02 | MBw/s 0.07 | avq 4.86 | avio 1.04 ms | I frankly don't understand why only sda is taking all the hit. I do have one process that is constantly writing with 1-2megs but what the hell.. 100% iowait?

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• Millions of files in php's tmp error - how to delete?

  - by Jonatan Littke

  Hey. I've got a tmp-folder with 14 million php session files in my home directory. At least that's what I think it is, it's not like I could ls it or anything. How can I empty this folder? I've tried using find with the -exec rm {} \; commands but that didn't work. ls 'sess_0*' | xargs rm did neither. I'm currently running rm -rf tmp but after two hours the folder appears to be the same size. REFERENCE INFO: I suddenly encountered an error where SESSIONS could no longer be written to disk: [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: open(/var/www/clients/client1/web1/tmp/sess_8e12742b62aa68a3f9476ec80222bbfb, O_RDWR) failed: No space left on device (28) in Unknown on line 0 [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/www/clients/client1/web1/tmp) in Unknown on line 0 I ran: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 457G 126G 308G 29% / tmpfs 1.8G 0 1.8G 0% /lib/init/rw udev 10M 664K 9.4M 7% /dev tmpfs 1.8G 0 1.8G 0% /dev/shm But as you can see, the disk isn't full. So I had a look in the syslog which says the following 20 times per second: kernel: [19570794.361241] EXT3-fs warning (device md0): ext3_dx_add_entry: Directory index full! This led me thinking to a full folder, obviously, but since my web folder only has 60k files (having counted them), I guessed it was the tmp folder (the local one, for this instance of php) that messed things up. Some commands I ran: $ sudo ls sess_a* | xargs rm -f bash: /usr/bin/sudo: Argument list too long find . -exec rm {} \; rm: cannot remove directory '.' find: cannot fork: Cannot allocate memory I'm running Debian Lenny, php5, ISPConfig, SuEXEC and Fast-CGI.

  Read the article

• Dual Monitor setup issues between laptop and external led monitor

  - by Julian

  I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

  Read the article

• Using public interfaces on a server connected through a GRE tunnel

  - by Evan

  I'm pretty new to networking so please forgive any terminology mistakes. I have 2 servers connected with a GRE tunnel. Server1 (10.0.0.1) ---- Server2 (10.0.0.2) I want to be able to bind to the public IPs on Server2 using Server1. To do this, I setup virtual interfaces with Server2's public IPs on Server1 and then used routing rules on Server1 to route the packets through the GRE tunnel. On Server1: ip rule add from [Server2's first public IP] table gre ip rule add from [Server2's second public IP] table gre ip route add default via 10.0.0.2 dev gre1 table gre This works great and I can see the packets arriving via GRE on Server2. I can see the packet exiting the tunnel on Server2's gre1 device as shown: From Server1: ping -I [Server2's public ip] google.com tcpdump from Server2's GRE tunnel device: 12:07:17.029160 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) [Server2's public ip] > 74.125.225.38: ICMP echo request, id 6378, seq 50, length 64 This is exactly the packet I want. However, I'm not seeing it go out at all on eth0:0 (where Server2's public IP is bound to). I've tried to use routing rules to get packets coming from Server2's public IP (which would be coming out of dev gre1) to go through dev eth0 on the public default gateway and that doesn't work either. I'm at a loss, thank you to anyone who can help.

  Read the article

• RAID administration in Debian Lenny

  - by Siim K

  I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

  Read the article

• No sound through headset - only mic is working

  - by Kristis

  I noticed that no sound is being played to my headphones. The laptop has a conexant sound card together with the sounds apps provided. But the thing is that I also noticed that now instead of one playback device - 2 are presented: speakers and headphones. And while speakers do play sound nicely - even test sound are not played through headphone output. Also, headphone output does not have a jack assigned to it, while speakers have L R Rear panel Analog Jack(my laptop does not have a jack on the back - only on the right). Also - my headphones have a mic as well - and when I plug it in - the mic is working(using top panel digital jack),but the headphones themselves are not. And laptop is recognizing when audio device is plugged in. And I checked the headset on other devices - the headphones are working. I have tried updating drivers, rolling back drivers and completely uninstalling drivers and then restarting - nothing helped. I imagine that I somehow need to reconfigure the jack configuration just have no idea how and where. Any suggestions? Thanks

  Read the article

• How to best tune my SAN/Initiators for best performance?

  - by Disco

  Recent owner of a Dell PowerVault MD3600i i'm experiencing some weird results. I have a dedicated 24x 10GbE Switch (PowerConnect 8024), setup to jumbo frames 9K. The MD3600 has 2 RAID controllers, each has 2x 10GbE ethernet nics. There's nothing else on the switch; one VLAN for SAN traffic. Here's my multipath.conf defaults { udev_dir /dev polling_interval 5 selector "round-robin 0" path_grouping_policy multibus getuid_callout "/sbin/scsi_id -g -u -s /block/%n" prio_callout none path_checker readsector0 rr_min_io 100 max_fds 8192 rr_weight priorities failback immediate no_path_retry fail user_friendly_names yes # prio rdac } blacklist { device { vendor "*" product "Universal Xport" } # devnode "^sd[a-z]" } devices { device { vendor "DELL" product "MD36xxi" path_grouping_policy group_by_prio prio rdac # polling_interval 5 path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And iscsid.conf : node.startup = automatic node.session.timeo.replacement_timeout = 15 node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 10 node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 After my tests; i can barely come to 200 Mb/s read/write. Should I expect more than that ? Providing it has dual 10 GbE my thoughts where to come around the 400 Mb/s. Any ideas ? Guidelines ? Troubleshooting tips ?

  Read the article

• How can I format an SD card with a more robust Linux-usable filesystem with a specific cluster size for better write performace?

  - by Harvey

  Goal: microSD card formatted... for best write performance for use only with embedded Linux for better reliability (random power failures may occur) using an 64kB cluster size I'm using an 8GB microSD card for data storage inside an embedded Linux/ARM device. The SD card is not removable. I've been using ext3 instead of the pre-installed FAT32 because it seems to better handle random power failures during writes. However, I kept noticing that my write performance is always best with the pre-installed FAT32 from Kingston. If I reformat the card with FAT32, the performance still suffers. After browsing wikipedia, I stumbled upon the following comment saying that some cards are optimized for specific cluster sizes. In my case, the Kingston comes pre-formatted for an 64kB cluster size. Risks of reformatting Reformatting an SD card with a different file system, or even with the same one, may make the card slower, or shorten its lifespan. Some cards use wear leveling, in which frequently modified blocks are mapped to different portions of memory at different times, and some wear-leveling algorithms are designed for the access patterns typical of the file allocation table on a FAT16 or FAT32 device.[60] In addition, the preformatted file system may use a cluster size that matches the erase region of the physical memory on the card; reformatting may change the cluster size and make writes less efficient.

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

• Event Log "Wake Source" when system wakes from sleep

  - by Doltknuckle

  So I've been troubleshooting sleep timers for our systems and have run across an interesting issue. I need a way to report how long a system was awake after a number of different inputs. Now, I've discovered that the System Log tracks wake and sleep events and even tells you the times that everything happens at. The thing is doesn't tell you is what triggered the wake event. It does give you a numerical code however. Here are some examples of what I am finding. Index : 2901 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T23:20:06.097488100Z Wake Time: 2010-10-03T17:41:12.796400500Z Wake Source: 0 Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter -- Index : 2841 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T19:19:37.239789600Z Wake Time: 2010-10-01T21:28:48.921200800Z Wake Source: 4HID Keyboard Device Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter So here's my question: Does anyone know what the different numerical codes for the "Wake Source" mean? I think "0" is a magic packet and "4" is a USB device. Does anyone have any idea if there is any documentation out there on this for Windows 7? Thanks in advance

  Read the article

• No apparent reason for high load average

  - by Oz.

  We have several web servers running on Amazon (ec2) c1.xlarge, over Amazon AMI. The servers are duplicates of each other, running the exact same hardware and software. Each server spec is: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge A couple of weeks ago we have run a yum upgrade on one of the servers. Starting on this upgrade the upgraded server started showing a high load average. Needless to say, we did not update the other servers and we can not do so until we understand the reason for this behavior. The strange thing is that when we compare the servers using top or iostat, we can not find the reason for the high load. Note that we have moved traffic from the "problematic" server to the others, which have made the "problematic" server less crowded in terms of requests, and still his load is higher. Do you have any idea what could it be, or where else can we check? Many thanks for the help! Oz. # # proper server # w command # 00:42:26 up 2 days, 19:54, 2 users, load average: 0.41, 0.48, 0.49 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/1 82.80.137.29 00:28 14:05 0.01s 0.01s -bash pts/2 82.80.137.29 00:38 0.00s 0.02s 0.00s w # # proper server # iostat command # Linux 3.2.12-3.2.4.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 9.03 0.02 4.26 0.17 0.13 86.39 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.63 1.50 55.00 367236 13444008 xvdfp1 4.41 45.93 70.48 11227226 17228552 xvdfp2 2.61 2.01 59.81 491890 14620104 xvdfp3 8.16 14.47 94.23 3536522 23034376 xvdfp4 0.98 0.79 45.86 192818 11209784 # # problematic server # w command # 00:43:26 up 2 days, 21:52, 2 users, load average: 1.35, 1.10, 1.17 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/0 82.80.137.29 00:28 15:04 0.02s 0.02s -bash pts/1 82.80.137.29 00:38 0.00s 0.05s 0.00s w # # problematic server # iostat command # Linux 3.2.20-1.29.6.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 7.97 0.04 3.43 0.19 0.07 88.30 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.10 1.49 76.54 374660 19253592 xvdfp1 5.64 40.98 85.92 10308946 21612112 xvdfp2 3.97 4.32 93.18 1087090 23439488 xvdfp3 10.87 30.30 115.14 7622474 28961720 xvdfp4 1.12 0.28 65.54 71034 16487112

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• Does btrfs balance also defragment files?

  - by pauldoo

  When I run btrfs filesystem balance, does this implicitly defragment files? I could imagine that balance simply reallocates each file extent separately, preserving the existing fragmentation. There is an FAQ entry, 'What does "balance" do?', which is unclear on this point: btrfs filesystem balance is an operation which simply takes all of the data and metadata on the filesystem, and re-writes it in a different place on the disks, passing it through the allocator algorithm on the way. It was originally designed for multi-device filesystems, to spread data more evenly across the devices (i.e. to "balance" their usage). This is particularly useful when adding new devices to a nearly-full filesystem. Due to the way that balance works, it also has some useful side-effects: If there is a lot of allocated but unused data or metadata chunks, a balance may reclaim some of that allocated space. This is the main reason for running a balance on a single-device filesystem. On a filesystem with damaged replication (e.g. a RAID-1 FS with a dead and removed disk), it will force the FS to rebuild the missing copy of the data on one of the currently active devices, restoring the RAID-1 capability of the filesystem.

  Read the article

• The Network folder specified is currently mapped using a different user name and password

  - by Frank Thornton

  I have a NAS device, it has 3 shares. On one computer I have access to all 3 of the shares. On another computer I keep getting this error when try and add a 2nd one. The Network folder specified is currently mapped using a different user name and password [...] That is the message I keep getting. What causes that? EDIT: Every share has it's own username and password. EDIT: NET USE on the one running 3 from the same NAS device New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK T: \\192.168.2.5\SHARE1 Microsoft Windows Network OK X: \\Nas-1dsho-abc\SHARE2 Microsoft Windows Network Disconnected Y: \\192.168.2.9\backups Microsoft Windows Network OK Z: \\Nas-1dsho-abc\cbackups Microsoft Windows Network The command completed successfully. NET USE on the other: New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK Y: \\192.168.2.5\SHARE1 Microsoft Windows Network Unavailable Z: \\192.168.2.5\SHARE2 Microsoft Windows Network The command completed successfully.

  Read the article

• Google Chrome warning that Javascript is disabled

  - by kirchoffs415

  I hope somebody can help. I keep getting the following message when I log on: Your Javascript is disabled. Limited functionality is available. It will stay for maybe a day sometimes two. I have uninstalled javascript and reinstalled but still the same. I am using chrome. Any help would be grateful many thanks Dominic My system spec is as follows System InformationOS Name Microsoft® Windows Vista™ Home Premium Version 6.0.6002 Service Pack 2 Build 6002 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name DOM-PC System Manufacturer Dell Inc. System Model Inspiron 1545 System Type X86-based PC Processor Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, 2000 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Dell Inc. A05, 25/02/2009 SMBIOS Version 2.4 Windows Directory C:\Windows System Directory C:\Windows\system32 Boot Device \Device\HarddiskVolume3 Locale United Kingdom Hardware Abstraction Layer Version = "6.0.6002.18005" User Name DOM-PC\DOM Time Zone GMT Standard Time Installed Physical Memory (RAM) 3.00 GB Total Physical Memory 2.96 GB Available Physical Memory 1.38 GB Total Virtual Memory 5.89 GB Available Virtual Memory 4.25 GB Page File Space 3.00 GB Page File C:\pagefile.sys My System Specs

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• DRBD setup problem

  - by cuthieu

  I'm so new to DRBD, please help me fixing the problem below. Enclosed my drbd.conf. Many thanks [root@skonkwerks1 ~]# drbdadm create-md all open(/dev/hdb3) failed: No such file or directory Command 'drbdmeta /dev/drbd0 v08 /dev/hdb3 internal create-md' terminated with exit code 20 drbdsetup exited with code 20 [root@skonkwerks1 ~]# vi /etc/drbd.conf global { usage-count no; } resource repdata { protocol C; startup { wfc-timeout 0; degr-wfc-timeout 120; } disk { on-io-error detach; } # or panic # net { cram-hmac-alg "hdd1"; shared-secret "testing"; } syncer { rate 10M; } on skonkwerks1 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.1:7788; meta-disk internal; } on skonkwerks2 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.2:7788; meta-disk internal; } }

  Read the article

• Is USB supported in safe mode on XP?

  - by Hugh Allen

  According Microsoft, "Universal Serial Bus Devices Do Not Work in Safe Mode" under XP. However, in my testing this is incorrect. USB keyboards, mice and flash drives seem to work fine in safe mode (I made sure the BIOS was not providing support). This makes sense because a failure of a standard input device would be, in Microsoft parlance, a "bad user experience". So, Is USB supported in safe mode on XP? If your answer is no (agreeing with Microsoft), please provide a test case, preferably in a virtual machine, where a standard HID keyboard or mouse fails. Please state hardware / BIOS / OS configuration. Note that you will need a PS/2 keyboard attached in addition to your USB device(s) in order to use the boot menu. Virtual machine software usually emulates a PS/2 keyboard. Alternatively, you could add the /safeboot switch to boot.ini. If your answer is yes, please provide a link to some supporting documentation (either from Microsoft or someone authoritative). Your answer might be "devices X, Y and Z are supported but nothing else", in which case also give a link.

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• Should tripwire be entering /proc?

  - by dsadinoff

  When initializing the db with tripwire --init it spat out a bunch of errors pertaining to /proc: ### Warning: File system error. ### Filename: /proc/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: Duplicate object encountered. ### /proc/sys/net/ipv6/neigh This feels like noise. The twpol.txt file has the following clause: # # Critical devices # ( rulename = "Devices & Kernel information", severity = $(SIG_HI), ) { /dev -> $(Device) ; /proc -> $(Device) ; } Which, if I understand it right, is going to cause tripwire to care deeply about the entire contents of /proc. Shouldn't it just care about the static parts of /proc like the drivers and such, and not the per-pid stuff? Why does it ship like this?

  Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >