Search Results

Search found 19640 results on 786 pages for 'tech support'.

Page 281/786 | < Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >

• System hangs while rebooting on Debian...

  - by Usman

  Hi, I have Debian (Kernel 2.6.26-2-686) installed on two computers. On one of them it reboots quite finely but I am having following problem with rebooting Debian on my second computer. When i type reboot at the Linux prompt, following messages appear and system hangs up after saying "Restarting System": Broadcast message from root@myname (tty1) (Sun Jan 17 11:23:26 2010) The system is going down for reboot NOW! INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Saving system clock Stopping enhanced syslog: rsyslogd. Asking all remaining processes to terminate...done. Deconfiguring network interfaces...done. Cleaning up ifupdown.... Deactivating swap...done. [ 31.789103] Restarting System. _ Normally when the sytem is busy "" sign blinks but "" at the last line above does not blink which shows, the system hanged up. I tried all keys but the screen is still frozen at the same point. The difference that I noted between my two computers is that I don't have ACPI support in the BIOS of the system which is giving me this error whereas the BIOS of my first computer do have ACPI support on which Debain do not give this restart-hanging problem. I have also disabled running the acpid script by running update-rc.d -f acpid remove but the problem still persists on the second computer. Any ideas to solve or get around this problem?

  Read the article

• Win 7 Privilege Level (Run as administrator) via GP or command line

  - by FinalizedFrustration

  Is there a way to set the Privilege Level for legacy software via group policy or on the command line? I have some legacy software, which we unfortunately cannot move away from. This software requires administrator access. I know I can go into the Properties dialog and check "Run this program as an administrator" on every single instance on every single one of my workstations, but that gets old after the 30th install. If I had my way, we would dump this software, find some software that did what we needed, was fully compliant with Win7 security best-practices and give everyone limited user accounts... However, I am not the boss, so everyone gets administrator accounts. Given that, I suppose I could just tell everyone to open the context menu and choose "Run as administrator", but we have some very, very, VERY low-tech users, and half of them might just choose "Delete" instead. Anyone know of a way to set this option on the command line? or better yet, through Group Policy?

  Read the article

• Event Log: atapi - the device did not respond within the timeout period - Freeze

  - by rjlopes

  Hi, I have a Windows Server 2003 that stops working randomly (displays image on monitor but is completely frozen), all I could found on the event log as causes were an error from atapi and a warning from msas2k3. The event log entries are: Event Type: Error Event Source: atapi Event Category: None Event ID: 9 Date: 22-07-2009 Time: 16:13:33 User: N/A Computer: SERVER Description: The device, \Device\Ide\IdePort0, did not respond within the timeout period. For more information, see Help and Support Center at http : // go.microsoft.com / fwlink / events.asp. Data: 0000: 0f 00 10 00 01 00 64 00 ......d. 0008: 00 00 00 00 09 00 04 c0 .......À 0010: 01 01 00 50 00 00 00 00 ...P.... 0018: f8 06 20 00 00 00 00 00 ø. ..... 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 01 00 00 00 ........ 0030: 00 00 00 00 07 00 00 00 ........ Event Type: Warning Event Source: msas2k3 Event Category: None Event ID: 129 Date: 22-07-2009 Time: 16:14:23 User: N/A Computer: SERVER Description: Reset to device, \Device\RaidPort0, was issued. For more information, see Help and Support Center at http : // go.microsoft.com / fwlink / events.asp. Data: 0000: 0f 00 10 00 01 00 68 00 ......h. 0008: 00 00 00 00 81 00 04 80 ......? 0010: 04 00 00 00 00 00 00 00 ........ 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 01 00 00 00 81 00 04 80 ......? Any hints?

  Read the article

• Attempts at NIC teaming on Server 2008 R2 with PRO/1000 MT

  - by Klaus

  I have a Dell PowerEdge 1850 server and a gigabit switch that supports nic teaming (and was configured to do so). The server has a total of four Intel PRO/1000 MT ports, which also support teaming. But.. for some reason Intel does not actually have a version of the drivers/ProSet that will work for these cards on 2008 R2. You have to use the built-in drivers that come with 2008 R2, which do not support the additional features. According to their website, they have no plans to change this. Strangely enough, I experimented with various drivers in an attempt to force it to work. At one point, the teaming was working, but there were side effects (such as the DNS server refusing to start). So now I am back to running just one of the cards, (very) frustrated about the whole situation. I have looked all over to see if there is some way around this, but have not had any success. I know I can probably just get a new network adapter for it, but with the good deal I got, that would cost more than the server! :) While staying with 2008 R2, does anyone know of any possible alternatives? Thanks!

  Read the article

• Can I upgrade my Soltek sl-67a-c motherboard from Pentium II to Pentium III?

  - by jedatu

  I have a Pentium III processor and I thought I would replace the Pentium II on my Soltek SL-67A-C. The motherboard has Slot 1 so the PIII fits in fine, however, when I turn on the computer the bios does not come up. Here's the link to some specs on the board: http://stason.org/TULARC/pc/motherboards/F/FLASH-TECH-INC-Pentium-II-Deschutes-SL-67A-C.html I know that I updated the bios at one time. I see references to a "67af3.zip" bios upgrade file out there but can't find any source to download it. I am thinking I may have to adjust the jumpers on the motherboard to match the speed of the processor, but I am not sure how to go about that. Any suggestions?

  Read the article

• Open Source webapp that shows PC / Projector status in 30+ Lecture rooms

  - by Seanchán

  I am looking for a simple web application that only has a simple graphical representation of the current status of 30+ lecture rooms. I.e. Green = good, Red=bad i.e. PC or Projector not working. With a little message and a ETA as well. I am not looking for monitoring software, merely a way for a tech to flag a room as "technically challenged" until 1PM or until "Friday 10AM". With a message for those lecturers who are interested: "Waiting on replacement bulb" or "Power supply gone" I know this is a simple thing to code up yourself, but I am looking for something that has been around for a few years that has some cool extra little functionality that you wouldn't think of yourself. I just can't find anything like that out there. And just to be clear: not monitoring software, more like lecturer feedback web app.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• Can any iSCSI NAS appliance replicate / clone a LUN to an external drive?

  - by Boden

  I would like to backup using Windows Imaging to some kind of NAS appliance. I believe this will require the NAS to support iSCSI. I would then like the appliance to support the replication of the iSCSI LUN to an external eSATA or USB disk connected directly to the appliance. I've found plenty of NAS appliances that can do iSCSI and replicate to an external drive, but none that I've found thus far can do both at once. That is, the devices can do iSCSI, but then the replication feature doesn't work. The idea here is to backup to an appliance located in a secure office far away from the server room. Offsite backups to external hard drive could be managed from the appliance. The benefits of such a setup would be: 1) very unlikely that fire or random theft would affect both server-room backup and "remote" backup appliance 2) offsite backups could be managed by multiple trusted people without granting access to server room 3) Windows imaging provides poor man's deduplication, so each backup volume can contain a decent backup history. I understand why this would be a non-trivial thing to implement, but I'm wondering if such a thing exists? Preferably a tabletop, low to medium cost device. Alternative solutions welcome. NOTE: I'm backing up very few but very large files, so file replication is not a good option.

  Read the article

• Options for synchronizing Palm Desktop calendars

  - by Al Everett

  My wife and I each have Palm Centro phones and very full calendars. We've been using Palm products for years and are happy with them and are not looking to switch (and don't have the budget for it even if we wanted to). What is a viable way we can synchronize our calendars? Back when we had Palm Z22s we used AirSet. It worked great in synchronizing our desktop calendars. Unfortunately, their sync software does not support Palm Desktop v6 and there is nothing in the pipeline to support it. (The third party vendor is apparently not interested in updating for the newer Palm desktop.) I would love to be able to get back to having each other's appointments appear on the other's calendar. What can we do? Some limitations: A data plan is not an option (so this precludes over-the-air synchronization options) No Microsoft Outlook Edit: Syncing my Palm to my Palm Desktop is not the issue. Being able to sync, in some way, the Palm calendar databases of my wife's and my calendars is what's desired.

  Read the article

• Fighting Spam - What can I do as an: Email Administrator, Domain Owner, or User?

  - by Chris S

  This is a Canonical Question about Fighting Spam. Also related: How to stop people from using my domain to send spam? There are so many techniques and so much to know about fighting SPAM. What widely used techniques and technologies are available to Administrator, Domain Owners, and End Users to help keep the junk out of our inboxes? We're looking for an answer that covers different tech from various angles. The accepted answer should include a variety of technologies (eg SPF/SenderID, DomainKeys/DKIM, Graylisting, DNS RBLs, Reputation Services, Filtering Software [SpamAssassin, etc]); best practices (eg mail on Port 25 should never be allowed to relay, Port 587 should be used; etc), terminology (eg, Open Relay, Backscatter, MSA/MTA/MUA, Spam/Ham), and possibly other techniques.

  Read the article

• Outlook and IMAP - Outlook doesn't allow the Drafts and Trash folders to sync with the respective IMAP folders

  - by Matt

  I'm using Outlook 2007 and Outlook 2010 against an IMAP server (the problem exists across many, like Gmail, you name it). Outlook lets you set your Outlook "Sent" folder to map to the IMAP server's Sent folder (the other choice is to map your Outlook Sent to your Personal Folders Sent) - this is good. When you send a message from Outlook and then look in the sent folder of the IMAP server (e.g. from a different client or from a browser), the messages are there. This is the behavior I want. Outlook does NOT support the same behavior for Drafts and Trash. In both cases, items deleted (or Drafts saved) in Outlook go in to Outlook's local folders and do NOT show on the IMAP server's Trash or Drafts folders. Same problem in reverse. Thunderbird on the other hand does support the proper mapping of Drafts, Sent and Trash. I expected this to be IMAP-specific but it appears to be client specific. What does Outlook implement it this way and is there a workaround?

  Read the article

• Domino to Exchange 2007 (or 2010) Design Concerns?

  - by NickToyota

  Today we got the executive green light to proceed with changing from a Domino platform to Exchange. The business prefers Exchange for a messaging platform. (even though IMO IBM Domino is fine - if it aint broke, don't fix it but it was not my call). I have been put in charge of Domino to Exchange process goes smoothly as possible. I have also been told to put together costs for this project. I have some questions and concerns re: network design, licensing, costs: The current setup is as follows. 1 HQ office (100 users), 1 secondary office (50 users), 5 branch offices (under 10 users). 5 different email domains Windows Server 2003 functional level with a few 2008 R2 Servers Lotus Domino Notes Servers (one in each office) Ironmail Appliance Public Domino Web Mail server Majority G5+ Proliant Servers Domino Blackberry Enterprise license and server No VoIP phones What are the basic hardware requirements for Exchange 2007 or 2010? Can I simply purchase a single physical server? Will each office require an Exchange server or possibly additional servers (roles)? How is email routed to the smaller branch offices? Standard or Enterprise licenses? The business has been running Domino (messaging and application services) for over 10 years and also want Exchange to support email services, Blackberry, Outlook Web Access, possibly support for iPhone devices. Thank you Serverfault universe.

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• IIS seems to send email twice

  - by David Brunelle

  Hi, we have a request page in our website that send email to confirm the request. It seem that whenever this page is accessed, some (not all of them) are sent more than once at different time, sometime hours apart. The code (which is an old ASP page) looks fine as it sends only once to the recipient. So I doubt it's a programming related problem. When looking at the Exchange server, the tech told me that he seems to be receiving the request twice at different time, so the problem comes from what's between the code and Exchange. My hypothesis is that IIS seem to 'remember' the page and rerun it for some reason. Any hint on where to start? We have IIS 6 (in french if it makes any difference) with Exchange 2007. IIS is running on a Windows Server 2003 machine (virtual machine I believe) in a DMZ. I don't know about Exchange. Thank you.

  Read the article

• Program to print gCal or iCal calendars in a monthly one calendar per column format

  - by David Smith

  I'm moving my family off of using the low tech "Boynton Mom's Family Calendar" to schedule things but I'd like to be able to create a monthly printout of the calendar in the same "Boynton" format (I'm sure it has an official name). The format is kind-of like a spreadsheet where each row of the calendar is a different day of the month and there is a separate column for each person in the family. I have all our calendars on Google but they are also accessible from iCal on the Mac. Is there a Mac program that can get the data from gCal or iCal print out the calendars in the Boynton format?

  Read the article

• What is the crappiest network build you've ever seen?

  - by Ivan Petrushev

  This is only about networks you have seen personaly, not heared from others or seen on pictures at the web. Cables hanging from the ceiling lamps? Cables going trough culverts and other tubes? Switches and other equipment in the cleaner's closet? Cleaning lady's rags drying hanging from the cables? Key to the main node door possesed only by the janitor (or other non-tech and completely non-network-related guy)? Switches powered by foreign power adapters (cheaper and providing non-specified voltage or amperage)? All of this was in my old dormitory. Tell us about your bad experience.

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• Windows 7 : Any way to disable "show caracter" in WIFI network properties?!

  - by Fox

  Hi everyone, Here's my issue. I'm working in a school as IT Tech and I'm currently planning to roll out Windows 7 on students laptop. The issue is : When you go to the properties of a WIFI network, you have the fields to input the WIFI key, WPA2 key here in my case, and you also have a checkbox that allow you to "unmask" the caracters of the wifi key. This is actually the problem. Anyone who can access the WIFI network properties, will be able to see the WIFI key, which is really an issue in a school envrironnement where student are all eager to get the key for their precious IPod Touch, what I don't want to happen for obvious reasons... So, is there a way to disable that checkbox or else, make the field cleared out when the checkbox is checked, just like it was on Windows XP or Vista? Thanks all for your answer.

  Read the article

• Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

  - by D.S.

  I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

  Read the article

• Linux Sound Drivers - Recompiling kernel with ehcd-hcd module

  - by jhome

  I just installed Linux Mint and I am trying to get my usb soundcard to work. I am completely new to Linux so I have only been learning about all the important parts of the OS this afternoon. No one I know has compiled kernel so I can't ask anyone. I am following instructions on this site: http://wiki.ubuntuusers.de/Benutzer/BigMc#Final-setup-of-US-122L-US-144 "Recompile your Kernel with ehcd-hcd as a module: Instructions for Ubuntu (german) Change "Device Drivers - USB support - EHCI HCD (USB 2.0) support)" to "M" when configuring. Make sure you also install the kernel headers." I know how to do any of these processes. Someone mentioned a package manager. Is recompiling basically in layman's terms reinstallation? Where do I go to the change device drivers? Cheers Edit: I am attempting to be able to use my Tascam US-144 on Linux Mint. Apparently, to use it properly it has to regress to functionality of a former unit (US-122), so according to the instructions a USB port has to be USB 1.0, rather than USB 2.0. I've tried using that ndis** programme for wireless drivers but with no success.

  Read the article

• How do I export address book from N97

  - by mplungjan

  Hi, I need to copy my numbers from my private Nokia to my office BB. I have not found a way to export my phone numbers from ovi or elsewhere. On Mac iSync stopped working with snow leopard and OVI on windows does not export. I do not mind using a windows suggestion. I lost a description on how to use the ovi backup files in another program. What I have done so far terminal: sudo open -a iSync.app - it launched but iSync said "this device is not supported by iSync" went here http://europe.nokia.com/support/product-support/isync/compatibility-and-download found a plugin (I am sure that was not there a while ago :| ) Checked software version 22.0.110 installed plugin Ran iSync which found and installed my N97 device successfully. synced. It stopped with The connection was lost while talking to the phone. http://discussions.europe.nokia.com/t5/Nseries-and-S60-Smartphones/N97-iSync-Multimedia-Transfer-Modem/m-p/568560 no news since Jan 2010. Tried to download and install http://best-vcard.en.softonic.com/symbian but the installer fails :( I simply do not understand why Nokia is giving us such a hard time. I would not have considered switching from Nokia if Mac had been better supported. It is so frustrating that they just seem not to care losing Nokia fanbois like me - especially since I am this outspoken on the net and what i say on popular forums gets indexed by google fast. I am very close to just go iPhone here. Hope someone has Nokia's ears UPDATE: I Downloaded NbuExplorer from sourceforge. It will extract everything from an OVI backup into VCF, VCS and VMG files. Very useful software and free.

  Read the article

• Problem with TL-R480T+ and static routes

  - by Globulopolis

  Hi! I've some question about this router. Before starting, some configurations, specified by my provider. Wan1 VPN IP - 192.168.172.84 Mask - 255.255.255.0 Gateway - 192.168.172.253 DNS - 195.110.6.7 Wan2 Dynamic IP DHCP - 168.120.1.34 Mask - 255.255.255.0 Router IP 192.168.1.1 Computer IP 192.168.1.7 Routes: route -p add 192.168.0.0 mask 255.255.0.0 192.168.172.253 route -p add 195.110.6.0 mask 255.255.254.0 192.168.172.253 route -p add 88.135.112.0 mask 255.255.240.0 192.168.172.253 route -p add 178.219.160.0 mask 255.255.240.0 192.168.172.253 For first provider I need to provide a routes. 'Cause router does not support different routes for different WAN interfaces I put them in "Static routes". But when I try to save them I've got an error: Destination IP address can not be set in a same subnet with the WAN or LAN IP address. If I change IP's to local like 192.168.x.x router tell me: Gateway must be set in a same subnet with WAN or LAN IP address. Changing mask on WAN1 interface to 255.255.0.0 doesn't help. Any ideas? PS! Or maybe I'm must email to TP-Link support?

  Read the article

• Enable Soap for PHP 5.5.x on CentOS 6.5

  - by Chris Mancini

  Unfortunately I have to support soap on my server for the Fedex webservice. I recompiled PHP enabling support and it works via CLI but not PHP-fpm. They both point to the same ini file and both show the module loaded, but only CLI shows the configuration values. Output of php -i | grep -i soap Configuration File (php.ini) Path => /usr/local/etc Loaded Configuration File => /usr/local/etc/php.ini Configure Command => './configure' '--prefix=/usr/local' '--with-config-file-path=/usr/local/etc' '--with-config-file-scan-dir=/usr/local/etc/php_user/' '--enable-fpm' '--enable-ftp' '--enable-libxml' '--enable-mbstring' '--enable-pdo' '--enable-soap' '--enable-sockets=shared' '--enable-zip' '--with-curl' '--with-fpm-group=nginx' '--with-fpm-user=nginx' '--with-freetype-dir=/usr/lib64/' '--with-gd' '--with-jpeg-dir=/usr/lib64/' '--with-libdir=lib64' '--with-mcrypt' '--with-openssl' '--with-pdo-mysql' '--with-pear' '--with-readline' '--with-tidy' '--with-xsl' '--with-zlib' '--without-pdo-sqlite' '--without-sqlite3' soap Soap Client => enabled Soap Server => enabled soap.wsdl_cache => 1 => 1 soap.wsdl_cache_dir => /tmp => /tmp soap.wsdl_cache_enabled => 1 => 1 soap.wsdl_cache_limit => 5 => 5 soap.wsdl_cache_ttl => 86400 => 86400 Output from php-fpm phpinfo(): Configuration File (php.ini) Path /usr/local/etc Loaded Configuration File /usr/local/etc/php.ini SOAP Brad Lafountain, Shane Caraveo, Dmitry Stogov Please help, I have tried so many things...

  Read the article

• Pitfalls to using Gluster as a home/profile directory server?

  - by Bart Silverstrim

  I was asking recently about options for divvying up access to file servers, as we have a NAS solution that gets fairly bogged down when our users (with giant profiles, especially) all log in nearly simultaneously. I ran across Gluster and it looks like it can cluster different physical storage media into a single virtual volume and share it out like a virtual NAS from the client perspective and it support CIFS. My question is whether something like this would be feasible to use for home and profile directories in an active directory environment. I was worried about ACL's, primarily, as I didn't think CIFS was fine-grained enough to support NTFS permissions and it didn't look like Gluster exports those permission levels, just the base permissions for basic file sharing. I got the impression that using Gluster would allow for data to be redundant across multiple servers and would speed up access to the files under heavy load, while allowing us to dynamically boost storage capacity by just adding another server and telling Gluster's master node to add that server. Maybe I'm wrong with my understanding of it though. Anyone else use it or care to share how feasible this is?

  Read the article

• Enable hardware virtualization in BIOS?

  - by rhon

  I am running a FOXCONN AM2+ M61PMV with an AMD Athlon II X2 240 Windows 7 ultimate 64 bit. From startup I have hit the del key and the options for enabling the hardware virtualization are not there. I have checked the Microsoft tool that says I can run virtual and i have checked SecurAble, that says yes. But I have an open case w/microsoft (they've been trying for a week [7 tech support people later]) and they're saying that I need to ensure that the hardware is enabled. Where do I go to see? Is there another way besides from the startup?

  Read the article

< Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >