Search Results

Search found 20313 results on 813 pages for 'batch size'.

Page 282/813 | < Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >

  • Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

    - by Shoshomiga
    I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

    Read the article

  • wireless blocked after installing ubuntu 12.04

    - by Cornelia Frank
    I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

    Read the article

  • Sound card not detected in 13.04

    - by Ganessh Kumar R P
    I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

    Read the article

  • How to efficiently dump a huge MySQL innodb database?

    - by Jagbir
    I got an Ubuntu 10.04 production MySQL database server where total size of database is 260 GB while size of root partition is itself 300 GB where DB is stored, essentially means around 96% of / is full and there's no space left for storing dump/backup etc. No other disk is attached to server as of now. My task is to migrate this database to other server sitting in different datacenter. Question is how to do that efficiently with minimum downtime? I'm thinking in line of: Request to attach an extra drive to server and take a dump in that drive. Transfer dump to new server, restore it and make new server slave of existing one to keep data in sync When migration is needed, break replication, update slave config to accept read/write requests and make old server read-only so it won't entertain any write requests and tell app developers to update there config with new IP address for db. What's your suggestions to improve this or any alternate better approach for this task?

    Read the article

  • unable to send mail from postfix on Ubuntu 12.04

    - by gilmad
    I'm trying to send an email through Google from my localhost. (via PHP5.3) But Google keeps on blocking my requests. I tried to follow the solutions given to a few similar questions, but for some reason they do not work. I followed these instructions to configure it - http://www.dnsexit.com/support/mailrelay/postfix.html Now for the config data: my main.cf file looks like that: relayhost = [smtp.gmail.com]:587 smtp_fallback_relay = [relay.google.com] smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = my sasl_passwd looks like that: [smtp.gmail.com]:587 [email protected]:password and that is how the mail.log rows look like: Dec 14 10:24:50 COMP-NAME postfix/pickup[5185]: 1C3987E0EDD: uid=33 from= Dec 14 10:24:50 COMP-NAME postfix/cleanup[5499]: 1C3987E0EDD: message-id=<[email protected] Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: 1C3987E0EDD: from=, size=483, nrcpt=1 (queue active) Dec 14 10:24:50 COMP-NAME postfix/smtp[5501]: 1C3987E0EDD: to=, relay=smtp.gmail.com[173.194.70.109]:587, delay=0.61, delays=0.19/0/0.32/0.1, dsn=5.7.0, status=bounced (host smtp.gmail.com[173.194.70.109] said: 530 5.7.0 Must issue a STARTTLS command first. w3sm8024250eel.17 (in reply to MAIL FROM command)) Dec 14 10:24:50 COMP-NAME postfix/cleanup[5499]: C20677E0EDE: message-id=<[email protected] Dec 14 10:24:50 COMP-NAME postfix/bounce[5502]: 1C3987E0EDD: sender non-delivery notification: C20677E0EDE Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: C20677E0EDE: from=<, size=2532, nrcpt=1 (queue active) Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: 1C3987E0EDD: removed

    Read the article

  • Importing video from a videotape recorded on Sony Handycam

    - by Akhil Langer
    I used Windows Movie Maker to import videos from a videotape recorded on Sony handycam. I imported the video in .avi format( as it was giving the best video quality), but the size of the video is very large (8GB for just 1 hour). Moreover, it takes a lot of time to import the video in Windows Movie Maker (approx. 2.5 hrs. for 1 hour video). Please suggest some other software which is more robust in the sense that it can give good quality video in lesser size and also it should be able to import the video quickly(as I have to import many video cassettes).

    Read the article

  • XNA 2D Spritesheet drawing rendering problem

    - by user24092
    I'm making a tile-based game, using one spritesheet containing all tile graphics. Each tile has a size of 32x32 pixels. The main problem is: when I draw the tile to the screen, if the tile position x and y are not rounded or if scale is activated in spriteBatch.Draw() method (scale != 1.0f), I get some lines of adjacent tiles on the spritesheet into the current tile drawed. I already tried setting SamplerState to PointClamp, removing AntiAlias, but still doesn't work. Here I'll show images of some tests that I made, with a test sprite sheet that I've created (I made a 9x9 spritesheet, with each sprite of size 32x32 containing a unique solid color). Tests: http://img6.imageshack.us/img6/5946/testsqj.png SpriteSheet used: http://imageshack.us/a/img821/1341/tilesm.png Already tried to remove anti-alias, set PointClamp as sampler state, but still getting this issue, XNA keeps drawing part of the adjacent pixels of the texture on the screen. What I want is to get the correct area of the tilesheet texture (as seen in the first test, that gets just the yellow pixels). My question is: Is there any way that I can fix this, WITHOUT adding tile spacing or any other modification involving the tilesheet? Maybe disabling a texture filtering that is done by XNA, or something like that.

    Read the article

  • Accessing second hard drive

    - by Jonathan
    So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris @djeykib So very close to fixing it.. unfortunately on the last command you gave it says this: $ sudo apt-get install linux-lts-backport-natty Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-lts-backport-natty Checking on http://www.ubuntuupdates.org/ppas reveals that it is only available for 10.04. Looks like I'll have to unplug and re-plug hardware if I want it working still :(

    Read the article

  • OpenGL - Rendering from part of an index and vertex array depending on an element count

    - by user1423893
    I'm currently drawing my shapes as lines by using a VAO and then assigning the dynamic vertices and indices each frame. // Bind VAO glBindVertexArray(m_vao); // Update the vertex buffer with the new data (Copy data into the vertex buffer object) glBufferData(GL_ARRAY_BUFFER, numVertices * sizeof(VertexPosition), m_vertices.data(), GL_DYNAMIC_DRAW); // Update the index buffer with the new data (Copy data into the index buffer object) glBufferData(GL_ELEMENT_ARRAY_BUFFER, numIndices * sizeof(unsigned short), indices.data(), GL_DYNAMIC_DRAW); glDrawElements(GL_LINES, numIndices, GL_UNSIGNED_SHORT, BUFFER_OFFSET(0)); // Unbind VAO glBindVertexArray(0); What I would like to do is draw the lines using only part of the data stored in the index and vertex buffer objects. The vertex buffer has its vertices set from an array of defined maximum size: std::array<VertexPosition, maxVertices> m_vertices; The index buffer has its elements set from an array of defined maximum size: std::array<unsigned short, maxIndices> indices = { 0 }; A running total is kept of the number of vertices and indices needed for each draw call numVertices numIndices Can I not specify that the buffer data contain the entire array and only read from part of it when drawing? For example using the vertex buffer object glBufferData(GL_ARRAY_BUFFER, numVertices * sizeof(VertexPosition), m_vertices.data(), GL_DYNAMIC_DRAW); m_vertices.data() = Entire array is stored numVertices * sizeof(VertexPosition) = Amount of data to read from the entire array Is this not the correct way to approach this? I do not wish to use std::vector if possible.

    Read the article

  • Worthless Anti-Spam (What can we learn)

    - by smehaffie
    I recently can across a site that had a “anti-spam” field at the bottom of the entry from.  The first issue I had with it was that at 1280X800 you could not read the value you were suppose to enter (see below).  You tell me, should you enter div, dlv, piv, or plv. But even worse than not being readable at high resolutions is the fact that the programmer who coded it really did not understand what this was used for.  An anti-spam (aka: catpcha) entry field should not be able to be read by looking at the HTML DOM object (so entry of value cannot be scripted).  In this case the value is simply a disabled text input filed that has the value you need to type.  So a hacker would simply need to search for text input field named “spam2” and then they could flood the site with spam. 1: <td> 2: <label> 3: <input name="spam1" type="text" class="small" id="spam1" size="6" maxlength="3" /> 4: <input name="spam2" type="text" class="small" id="spam2" value="plv" 5: disabled="disabled" size="6" maxlength="3" /> 6: * <span class="small">- Anti-SPAM key - please enter matching value</span> 7: </label> 8: </td>   There are some things to learn from this example: 1) Always make sure you understand why you are coding a feature/function for any program you write.  Just following the requirements without realizing the “why” will sooner or later come back to bite you.  I think the above example appears to be an example of this. 2) Always check how the screen appears in different resolutions.  In this case it was pretty much unreadable in 1280x800, but you could read it in 800X600 (but most people I know do not have their resolution set that low).  Lucky for me I could “View Source” and get the value I needed to enter.

    Read the article

  • Ubuntu Linux: Process swap memory and memory usage

    - by David Halter
    My Ubuntu eats more memory than the task manager is showing: sudo ps -e --format rss | awk 'BEGIN{c=0} {c+=$1} END{print c/1024}' 1043.84 free -m total used free shared buffers cached Mem: 3860 1878 1982 0 20 679 -/+ buffers/cache: 1178 2681 Swap: 2729 1035 1693 That's strange. Can someone explain this difference? But what is more important: I'd like to know how much memory a process is really using. I don't want to know the virtual memory size, but rather the resident memory plus swap of a process. I have also tried to output the format param "sz" of 'ps', but the sum of this is to high (5450 MB) (param 'size' gives 8323.45 MB). Are there any other options? I really want to use this, to determine which programs/processes are eating to much memory (and swap), to kill them, because hibernate might not be working if the swap partition is to little.

    Read the article

  • How do I stop cropping in iMovie?

    - by Javoid
    I'm not certain if 'crop' is the right term. I'm new to iMovie so I may have some of the terminology wrong. When I import a movie, I allow it to resize to the recommended settings instead of full size. Then I drag it from the lower event pane into the project pane. In the 'preview' pane where the movie can be played, the top and bottom of the movie are cut off a little. It's like its converting it to widescreen by cutting off the top and bottom. After I publish the movie in mobile format (it won't allow any larger) it still has the top and bottom removed. How can I stop this? I even tried importing full (original) size and it still didn't help.

    Read the article

  • Desktop Fun: Mountains Theme Wallpapers

    - by Asian Angel
    Do you love to go on hikes in the mountains and enjoy the scenery? Bring those sweeping views and a touch of the great outdoors to your desktop with our Mountains Theme Wallpaper collection. Note: Click on the picture to see the full-size image—these wallpapers vary in size so you may need to crop, stretch, or place them on a colored background in order to best match them to your screen’s resolution.         For more fun wallpapers be certain to visit our new Desktop Fun section. Similar Articles Productive Geek Tips Windows 7 Welcome Screen Taking Forever? Here’s the Fix (Maybe)Desktop Fun: Starship Theme WallpapersDesktop Fun: Underwater Theme WallpapersDesktop Fun: Forest Theme WallpapersDesktop Fun: Fantasy Theme Wallpapers TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Monitor Applications With Kiwi LocPDF is a Visual PDF Search Tool Download Free iPad Wallpapers at iPad Decor Get Your Delicious Bookmarks In Firefox’s Awesome Bar Manage Photos Across Different Social Sites With Dropico Test Drive Windows 7 Online

    Read the article

  • Mercurial says "nothing changed", but it did. Sometimes my software is too clever.

    - by user12608033
    It seems I have found a "bug" in Mercurial. It takes a shortcut when checking for differences in tracked files. If the file's size and modification time are unchanged, it assumes its contents are unchanged: $ hg init . $ cp -p .sccs2hg/2005-06-05_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg add nicstat.c $ hg commit -m "added nicstat.c" $ cp -p .sccs2hg/2005-07-02_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg diff $ hg commit nothing changed $ touch nicstat.c $ hg diff diff -r b49cf59d431d nicstat.c --- a/nicstat.c Fri Aug 24 11:21:27 2012 -0700 +++ b/nicstat.c Fri Aug 24 11:22:50 2012 -0700 @@ -2,7 +2,7 @@ * nicstat - print network traffic, Kb/s read and written. Solaris 8+. * "netstat -i" only gives a packet count, this program gives Kbytes. * - * 05-Jun-2005, ver 0.81 (check for new versions, http://www.brendangregg.com) + * 02-Jul-2005, ver 0.90 (check for new versions, http://www.brendangregg.com) * [...] Now, before you agree or disagree with me on whether this is a bug, I will also say that I believe it is a feature. Yes, I feel it is an acceptable shortcut because in "real" situations an edit to a file will change the modification time by at least one second (the resolution that hg diff or hg commit is looking for). The benefit of the shortcut is greatly improved performance of operations like "hg diff" and "hg status", particularly where your repository contains a lot of files. Why did I have no change in modification time? Well, my source file was generated by a script that I have written to convert SCCS change history to Mercurial commits. If my script can generate two revisions of a file within a second, and the files are the same size, then I run afoul of this shortcut. Solution - I will just change my script to apply the modification time from the SCCS history to the file prior to commit. A "touch -t " will do that easily.

    Read the article

  • Using photoshop actions to decide if an image needs to be rotated

    - by voxobscuro
    I have Photoshop CS3 and I need to do a batch on a lot of pictures before I upload them. The pictures need to fit in an 600x800 box, yet be as big as possible within that box. Some of them are much wider than taller and others are more tall than wide. I am trying to put together a photoshop action that will rotate, resize, and fill pictures as needed to make them as big as possible while staying within the 600x800 box. The only thing I haven't gotten sorted out is how to tell photoshop to rotate the image 90 degrees if that will allow the picture to be bigger within the constraints. Any ideas?

    Read the article

  • Calculating the correct particle angle in an outwards explosion

    - by Sun
    I'm creating a simple particle explosion but am stuck in finding the correct angle to rotate my particle. The effect I'm going for is similar to this: Where each particle is going outwards from the point of origin and at the correct angle. This is what I currently have: As you can see, each particle is facing the same angle, but I'm having a little difficulty figuring out the correct angle. I have the vector for the point of emission and the new vector for each particle, how can I use this to calculate the angle? Some code for reference: private Particle CreateParticle() { ... Vector2 velocity = new Vector2(2.0f * (float)(random.NextDouble() * 2 - 1), 2.0f * (float)(random.NextDouble() * 2 - 1)); direction = velocity - ParticleLocation; float angle = (float)Math.Atan2(direction.Y, direction.X); ... return new Particle(texture, position, velocity, angle, angularVelocity, color, size, ttl, EmitterLocation); } I am then using the angle created as so in my particles Draw method: spriteBatch.Draw(Texture, Position, null, Color, Angle, origin, Size, SpriteEffects.None, 0f);

    Read the article

  • Make the most of yourself and your team during Ramadan

    - by swalker
    Normal 0 false false false EN-GB X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} To remain competitive, you and your staff need training. The forthcoming Ramadan period adds even more restrictions to those like project deadlines, travel approval and increasing workloads. With Training On Demand these interferences that prevent the attendance of training courses disappear: you and your staff can learn any place, any time. You can find more information here. For assistance with bookings contact your local Oracle University Service Desk. Stay Connected to Oracle University: LinkedIn OracleMix Twitter Facebook Google+

    Read the article

  • Banshee gapless playback does not work when playing mp3s

    - by ComputerGuy505
    Even though I have gapless playback enabled in Banshee's settings menu, there is a very short pause between songs. This might be due to the fact that my hard drive's partitions seem wierd. fdisk -l produces this output: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4a73c3cb Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 724153740 361872070+ 7 HPFS/NTFS/exFAT /dev/sda3 1456826368 1465145343 4159488 c W95 FAT32 (LBA) /dev/sda4 724154366 1456826367 366336001 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 1440159744 1456826367 8333312 82 Linux swap / Solaris /dev/sda6 724154368 1440159743 358002688 83 Linux Partition table entries are not in disk order Playing mp3's from /dev/sda2 or /dev/sda6 produces this problem. I don't seem to have gapless playback on Rhythmbox or Clementine either, if those media players are supposed to have it. I'm not sure what other info to provide. This is just annoying to me. Thanks for any help.

    Read the article

  • Application windows have colossal fonts in Enlightenment 17, while system windows are untouched

    - by Matt
    I'm trying to get used to using Enlightenment instead of KDE on my Slackware64 multilib computer, but I'm having a terrible time getting one problem fixed. My fonts are HUGE on application windows - from Firefox to Gimp to Xchat to anything else, all the fonts are 3x the size they should be. But at the same time, the system menu is the correct size. I'm at a loss - I want the applications to have the same DPI as the system menu. When I'm in KDE, they all look normal. I've included a screenshot to show what I'm talking about.

    Read the article

  • Wireless connection disconnects and reconnects with a Netgear WNA1000

    - by William Berkenkamp
    Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

    Read the article

  • game play strategy in an arena

    - by joulesm
    I am writing a player's behavior for an arena game, and I'm wondering if you can offer some strategies. I'm writing it in Python, but I'm just interested in the high level game play. Here are the game aspects: Arena is a circle of a given size. The arena size shrinks every round to help break ties. Players are much smaller circles, can be on teams of 1 or 2 players. Players attack by colliding with other players, and based on the physics of the collision (speed of both players, angle), one could force another player out of the arena. Once a player is out of the arena, they are out of the game (for that round). The goal is to be the only team with players left in the arena. All other players have been pushed (through collisions or mistakes) out of the arena. It is possible for there to be no winner if the last two players exit the arena at the same time. Once the player has been programmed, the game just runs. There is no human intervention in the game. I'm thinking it's easiest to implement a few simple programmatic rules for my player to follow. For example, stay close to center of the arena, attack opponents from the inner side of the arena, etc. Are there any good simple game strategies? Would adding a random aspect to the game help? For example, to avoid predictability by the other team or something. Thanks in advance.

    Read the article

  • Is there a way to tell if a file is done copying?

    - by Mike Cooper
    The scenario is this: Machine A has files I want to copy to Machine C. Machine A can't access C directly, but can access Machine B that can access Machine C. I am using scp to copy from Machine A to B, and then from B to C. Machine B has limited storage space, so as files come in, I need to copy them to C and delete them from B. The second copy is much faster, so this is no problem with bandwidth. I could do this by hand, but I am lazy. What I would like is to run a script on B or C that will copy each file to C as each one finishes. The scp job is running from A. So what I need is a way to ask (preferably from a bash script) if file X.avi is "done" copying. Each of these files is a different size, and I can't really predict size or time of completion. Edit: by the way, the file transfer times are something about 1 hour from A to B and about 10 minutes from B to C, if time scale matters at all.

    Read the article

  • NTFS write speed really slow (<15MB/s)

    - by Zulakis
    I got a new Seagate 4TB harddrive formatted with ntfs using parted /dev/sda > mklabel gpt > mkpart pri 1 -1 mkfs.ntfs /dev/sda1 When copying files or testing writespeed with dd, the max writespeed I can get is about 12MB/s. The harddrive should be capable of atleast 100MB/s. top shows high cpu usage for the mount.ntfs process. The system has a AMD dualcore. This is the output of parted /dev/sda unit s print: Model: ATA ST4000DM000-1F21 (scsi) Disk /dev/sda: 7814037168s Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 2048s 7814035455s 7814033408s pri The used kernel is 3.5.0-23-generic. The ntfs-3g versions I tried are ntfs-3g 2012.1.15AR.1 (ubuntu 12.04 default) and the newest version ntfs-3g 2013.1.13AR.2. When formatted with ext4 I get good write speeds with about 140MB/s. How can I fix the writespeed?

    Read the article

  • Adding delay between damage

    - by iQue
    I have a bunch of enemies chasing my main-character, and if they intersect I want them to damage him and that's all good. The problem is that right now they damage him as long as they stand around him, every frame! and since it gets called every frame my character's HP reaches 0 almost instantly. I've tried adding delay and I've tried a timertask, but can't get it to work. This is the code I use to check for intersection: private void checkCollision(Canvas canvas) { synchronized (getHolder()) { Rect h1 = happy.getBounds(); for (int i = 0; i < enemies.size(); i++) { for (int j = 0; j < bullets.size(); j++) { Rect b1 = bullets.get(j).getBounds(); Rect e1 = enemies.get(i).getBounds(); if (b1.intersect(e1)) { enemies.get(i).damageHP(5); bullets.remove(j); } if(e1.intersect(h1)){ happy.damageHP(5); // this is the statement that needs some sort of delay, I want them to damage him every 2 seconds they intersect him. } if(enemies.get(i).getHP() <= 0){ enemies.get(i).death(canvas, enemies); score.incScore(5); break; } if(happy.getHP() <= 0){ score.incScore(-50); //end-screen } } } } } If anyone knows the logic to do this please do tell.

    Read the article

  • Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

    - by jindrichm
    I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

    Read the article

< Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >