Search Results

Search found 8839 results on 354 pages for 'optional parameters'.

Page 283/354 | < Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >

  • Figuring out the Nyquist performance limitation of an ADC on an example PIC microcontroller

    - by AKE
    I'm spec-ing the suitability of a dsPIC microcontroller for an analog-to-digital application. This would be preferable to using dedicated A/D chips and a separate dedicated DSP chip. To do that, I've had to run through some computations, pulling the relevant parameters from the datasheets. I'm not sure I've got it right -- would appreciate a check! (EDITED NOTE: The PIC10F220 in the example below was selected ONLY to walk through a simple example to check that I'm interpreting Tacq, Fosc, TAD, and divisor correctly in working through this sort of Nyquist analysis. The actual chips I'm considering for the design are the dsPIC33FJ128MC804 (with 16b A/D) or dsPIC30F3014 (with 12b A/D).) A simple example: PIC10F220 is the simplest possible PIC with an ADC Runs at clock speed of 8MHz. Has an instruction cycle of 0.5us (4 clock steps per instruction) So: Taking Tacq = 6.06 us (acquisition time for ADC, assume chip temp. = 50*C) [datasheet p34] Taking Fosc = 8MHz (? clock speed) Taking divisor = 4 (4 clock steps per CPU instruction) This gives TAD = 0.5us (TAD = 1/(Fosc/divisor) ) Conversion time is 13*TAD [datasheet p31] This gives conversion time 6.5us ADC duration is then 12.56 us [? Tacq + 13*TAD] Assuming at least 2 instructions for load/store: This is another 1 us [0.5 us per instruction] Which would give max sampling rate of 73.7 ksps (1/13.56) Supposing 8 more instructions for real-time processing: This is another 4 us Thus, total ADC/handling time = 17.56us (12.56us + 1us + 4us) So expected upper sampling rate is 56.9 ksps. Nyquist frequency for this sampling rate is therefore 28 kHz. If this is right, it suggests the (theoretical) performance suitability of this chip's A/D is for signals that are bandlimited to 28 kHz. Is this a correct interpretation of the information given in the data sheet in obtaining the Nyquist performance limit? Any opinions on the noise susceptibility of ADCs in PIC / dsPIC chips would be much appreciated! AKE

    Read the article

  • How to import data to SAP

    - by Mehmet AVSAR
    Hi, As a complete stranger in town of SAP, I want to transfer my own application's (mobile salesforce automation) data to SAP. My application has records of customers, stocks, inventory, invoices (and waybills), cheques, payments, collections, stock transfer data etc. I have an additional database which holds matchings of records. ie. A customer with ID 345 in my application has key 120-035-0223 in SAP. Every record, for sure, has to know it's counterpart, including parameters. After searching Google and SAP help site for a day, I covered that it's going to be a bit more pain than I expected. Especially SAP site does not give even a clue on it. Say I couldn't find. We transferred our data to some other ERP systems, some of which wanted XML files, some other exposed their APIs. My point is, is Sql Server's SSIS an option for me? I hope it is, so I can fight on my own territory. Since client requests would vary a lot, I count flexibility as most important criteria. Also, I want to transfer as much data as I could. Any help is appreciated. Regards,

    Read the article

  • Unable to display wap version during "Extended permission"

    - by Mickey Cheong
    Hi, Im trying to redirect to facebook to request permission to publish stream. However, it only works when i did not specify any display parameters, it shows me a web version of it. I wanted a wap version instead. What should I do? Here's the code: <form method="post" action="https://graph.facebook.com/oauth/authorize"> <input type="hidden" name="client_id" value="1XXXXXXXXXXXXXX" /> <input type="hidden" name="scope" value="publish_stream" /> <input type="hidden" name="redirect_uri" value="http://www.redirect.com/" /> <input class="button" type="submit" value="Request..." /> </form> When i submit this form, it will redirect to http://www.facebook.com/connect/prompt_ … y=page.... If I were to change the "redirected url"'s display param to "wap" it will works. However, if I were to submit to https://graph.facebook.com/oauth/authorize?display=wap. Nothing will happen and it will redirect back to the source url. Any help/hint will be grateful. Thanks a mil, Mickey

    Read the article

  • Retrieve Flash file post in ASP.NET

    - by Quandary
    Question: In ASP.NET, I retrieve a JPEG-file as Flash post data like this Sub ProcessRequest(ByVal context As HttpContext) Implements IHttpHandler.ProcessRequest context.Response.ContentType = "text/plain" ' Retrieve a bytearray from the post buffer Dim myBuffer As Byte() = context.Request.BinaryRead(Convert.ToInt32(context.Request.InputStream.Length)) System.IO.File.WriteAllBytes("c:\temp\test.jpg", myBuffer) End Sub In Flash, I send it to an asp.net handler like this var jpgSource:BitmapData = cPrint.TakeSnapshot(MovieClip(cGlobals.ccPlanZoomView)); var bmpThisBitmap:Bitmap = new Bitmap(jpgSource); var nQuality:Number = 100; var jpgEncoder:JPGEncoder = new JPGEncoder(nQuality); var jpgStream:ByteArray = jpgEncoder.encode(jpgSource); var header:URLRequestHeader = new URLRequestHeader ("Content-type", "application/octet-stream"); // Make sure to use the correct path to jpg_encoder_download.php var strFileName:String="test.jpg"; var jpgURLRequest:URLRequest = new URLRequest("http://localhost/raumplaner_new/raumplaner_new/cgi-bin/SavePDF.ashx"); //var scriptVars:URLVariables = new URLVariables(); //scriptVars.fn = strFileName; //var myarr:Array= new Array(); //myarr.push(jpgStream); //scriptVars.Files = myarr; jpgURLRequest.requestHeaders.push(header); jpgURLRequest.method = URLRequestMethod.POST; //jpgURLRequest.data = scriptVars; jpgURLRequest.data = jpgStream; var loader:URLLoader = new URLLoader(); loader.dataFormat = URLLoaderDataFormat.BINARY; loader.load(jpgURLRequest); It works but I want to send a few additional variables along, via scriptVars (commented out here). How do I retrieve the JPEG file in that case ? Because if I use parameters, there is no more BinaryRead... Aspecially, how would I read an array of jpeg files (several files) ?

    Read the article

  • Use localeURL middleware with apache prefix

    - by Olivier R.
    Good morning everyone, I Got a question about localeURL usage. Everything works great for me with url like this : www.mysite.com/ If I type www.mysite.com/ in adress bar, it turns correctly in www.mysite.com/en/ for example. If I use the view change_locale, it's also all right (ie change www.mysite.com/en/ in www.mysite.com/fr/). But my application use apache as server, and use a prefix for the site, that gives url like this : www.mysite.com/prefix/ If I type www.mysite.com/prefix/ in the adress bar, the adress turns into www.mysite.com/en/ without prefix (so 404) I change code of view to manage our settings.SERVER_PREFIX value : def change_locale(request) : """ Redirect to a given url while changing the locale in the path The url and the locale code need to be specified in the request parameters. O. Rochaix; Taken from localeURL view, and tuned to manage : - SERVER_PREFIX from settings.py """ next = request.REQUEST.get('next', None) if not next: next = request.META.get('HTTP_REFERER', None) if not next: next = settings.SERVER_PREFIX + '/' next = urlsplit(next).path prefix = False if settings.SERVER_PREFIX!="" and next.startswith(settings.SERVER_PREFIX) : prefix = True next = "/" + next.lstrip(settings.SERVER_PREFIX) _, path = utils.strip_path (next) if request.method == 'POST': locale = request.POST.get('locale', None) if locale and check_for_language(locale): path = utils.locale_path(path, locale) if prefix : path = settings.SERVER_PREFIX + path response = http.HttpResponseRedirect(path) return response with this customized view, i'm able to correctly change language, but i'm not sure that's the right way of doing stuff. Is there any option on localeURL to manage prefix of apache ?

    Read the article

  • Python: How to execute a SQL file or command

    - by Mestika
    Hi, I have this Python script: import sys import getopt import timeit import random import os import re import ibm_db import time from string import maketrans runs=5 queries=50 file = open("results.txt", "a") for r in range(5): print "Run %s\n" % r os.system("python reads.py -r1 -pquery1.sql -q50 -sespec") file.write('END QUERY READ 01') file.close() os.system("python query_read_02.py") Everything here is working, it is creating the results.txt file, it run the os.system("python reads.py...") file and that file is doing everything it's suppose to, but the problem comes when go and run the query_read_02.py file. In this file, it should execute a SQL command or a SQL file on my database, so I can create an index and see what the performance of that input is, but how do i do it? I create the connection to the database in the reads.py file, but it's hard to create the queries in there because I doesn't keep track of which file it has reached, it just execute commands from what the parameters are. I hope I've explained myself clear enough, otherwise please let me know. I just want to execute a SQL command or file which each query_read_0x.py file. Sincerely Mestika

    Read the article

  • Proper DateTime Format for a Web Service

    - by user48408
    I have a webservice with a method which is called via a xmlhttprequest object in my javascript. The method accepts a datetime parameter which is subsequently converted to a string and run against the database to perform a calculation. I get the value from m_txtDateAdd and send off the xmlHttprequest <asp:textbox id=m_txtDateAdd tabIndex=4 runat="server" Width="96px" Text="<%# Today %>"> </asp:textbox> which has a validator attacted to it <asp:CustomValidator id="m_DateAddValidator" runat="server" ErrorMessage="Please Enter a Valid Date" ControlToValidate="m_txtDateAdd">&#x25CF;</asp:CustomValidator> My webmethod looks something like this [WebMethod] public decimal GetTotalCost(DateTime transactionDate) { String sqlDateString = transactionDate.Year+"/"+transactionDate.Month+"/"+transactionDate.Day; I use sqlDateString as part of the commandtext i send off to the database. Its a legacy application and its inline sql so I don't have the freedom to set up a stored procedure and create and assign parameters in my code behind. This works 90% of the time. The webservice is called on the onchange event of m_txtDateAdd. Every now and again the response i get from the server is System.ArgumentException: Cannot convert 25/06/2009 to System.DateTime. System.ArgumentException: Cannot convert 25/06/2009 to System.DateTime. Parameter name: type --- System.FormatException: String was not recognized as a valid DateTime. at System.DateTimeParse.Parse(String s, DateTimeFormatInfo dtfi, DateTimeStyles styles) at System.DateTime.Parse(String s, IFormatProvider provider) at System.Convert.ToDateTime(String value, IFormatProvider provider) at System.String.System.IConvertible.ToDateTime(IFormatProvider provider) at System.Convert.ChangeType(Object value, Type conversionType, IFormatProvider provider) at System.Web.Services.Protocols.ScalarFormatter.FromString(String value, Type type) --- End of inner exception stack trace --- at System.Web.Services.Protocols.ScalarFormatter.FromString(String value, Type type) at System.Web.Services.Protocols.ValueCollectionParameterReader.Read(NameValueCollection collection) at System.Web.Services.Protocols.HtmlFormParameterReader.Read(HttpRequest request) at System.Web.Services.Protocols.HttpServerProtocol.ReadParameters() at System.Web.Services.Protocols.WebServiceHandler.CoreProcessRequest()

    Read the article

  • Turning off hibernate logging console output

    - by Jared
    I'm using hibernate 3 and want to stop it from dumping all the startup messages to the console. I tried commenting out the stdout lines in log4j.properties but no luck. I've pasted my log file below. Also I'm using eclipse with the standard project structure and have a copy of log4j.properties in both the root of the project folder and the bin folder. ### direct log messages to stdout ### #log4j.appender.stdout=org.apache.log4j.ConsoleAppender #log4j.appender.stdout.Target=System.out #log4j.appender.stdout.layout=org.apache.log4j.PatternLayout #log4j.appender.stdout.layout.ConversionPattern=%d{ABSOLUTE} %5p %c{1}:%L - %m%n ### direct messages to file hibernate.log ### log4j.appender.file=org.apache.log4j.FileAppender log4j.appender.file.File=hibernate.log log4j.appender.file.layout=org.apache.log4j.PatternLayout log4j.appender.file.layout.ConversionPattern=%d{ABSOLUTE} %5p %c{1}:%L - %m%n ### set log levels - for more verbose logging change 'info' to 'debug' ### log4j.rootLogger=warn, stdout #log4j.logger.org.hibernate=info log4j.logger.org.hibernate=debug ### log HQL query parser activity #log4j.logger.org.hibernate.hql.ast.AST=debug ### log just the SQL #log4j.logger.org.hibernate.SQL=debug ### log JDBC bind parameters ### log4j.logger.org.hibernate.type=info #log4j.logger.org.hibernate.type=debug ### log schema export/update ### log4j.logger.org.hibernate.tool.hbm2ddl=debug ### log HQL parse trees #log4j.logger.org.hibernate.hql=debug ### log cache activity ### #log4j.logger.org.hibernate.cache=debug ### log transaction activity #log4j.logger.org.hibernate.transaction=debug ### log JDBC resource acquisition #log4j.logger.org.hibernate.jdbc=debug ### enable the following line if you want to track down connection ### ### leakages when using DriverManagerConnectionProvider ### #log4j.logger.org.hibernate.connection.DriverManagerConnectionProvider=trac5

    Read the article

  • ColdFusion 8: Database Connection Reset Error

    - by Gavin
    I have been getting these intermittent ColdFusion Database connection reset errors and was wondering if anyone had experience with this and had a particular solution that worked? Here is the error: Error Executing Database Query.[Macromedia][SQLServer JDBC Driver]A problem occurred when attempting to contact the server (Server returned: Connection reset). Please ensure that the server parameters passed to the driver are correct and that the server is running. Also ensure that the maximum number of connections have not been exceeded for this server. This doesn't happen with any particular query, the code breaks in different queries every time, returning a SQLState error 08s01. These query's logic are fine, no logic errors etc. I checked the network logs and there were no database server connection refusals at the time of the error. Once the first error occurs, it keeps happening for no more than a minute or so at random times of the day, every few days. I've googled this thing and so far anyone that has had this issue was only on CF6 or 7, which the fixes coldFusion put out are only for CF6 or 7. Server configuration wise: The ColdFusion server is version 8 The database server is SQL Server 2005 Standard The database connections allowed setting is set to unlimited on both SQL Server and ColdFusion Any help would be greatly appreciated, Thanks!

    Read the article

  • Parsing SOAP XML in Oracle

    - by user258587
    Hi I am new to Oracle and I am working on something that needs to parse a SOAP request and save the address to DB Tables. I am using the XML parser in Oracle (XMLType) with XPath but am struggling since I can't figure out the way to parse the SOAP request because it has multiple namespaces. Could anyone give me an example? Thanks in advance!!! edit It would be a typical SOAP request similar to the one below. <soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/" xmlns:soap="http://soap.service.****.com"> <soapenv:Header /> <soapenv:Body> <soap:UpdateElem> <soap:request> <soap:att1>123456789</soap:att1> <soap:att2 xsi:nil="true" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" /> <soap:att3>L</soap:att3> ..... </soap:request> </soap:UpdateElem> </soapenv:Body> </soapenv:Envelope> I need to retrieve parameters att1, att2... and save them in to a DB table.

    Read the article

  • Mac OS X: Getting detailed process information (specifically its launch arguments) for arbitrary run

    - by Jasarien
    I am trying to detect when particular applications are launched. Currently I am using NSWorkspace, registering for the "did launch application" notification. I also use the runningApplications method to get apps that are currently running when my app starts. For most apps, the name of the app bundle is enough. I have a plist of "known apps" that I cross check with the name of that passed in the notification. This works fine until you come across an app that acts as a proxy for launching another application using command line arguments. Example: The newly released Portal on the Mac doesn't have a dedicated app bundle. Steam can create a shortcut, which serves as nothing more than to launch the hl2_osx app with the -game argument and portal as it's parameter. Since more Source based games are heading to the Mac, I imagine they'll use the same method to launch, effectively running the hl2_osx app with the -game argument. Is there a nice way to get a list of the arguments (and their parameters) using a Cocoa API? NSProcessInfo comes close, offering an `-arguments' method, but only provides information for its own process... NSRunningApplication offers the ability to get information about arbitrary apps using a PID, but no command line args... Is there anything that fills the gap between the two? I'm trying not to go down the route of spawning an NSTask to run ps -p [pid] and parsing the output... I'd prefer something more high level.

    Read the article

  • sqrt(int_value + 0.0) -- Does it have a purpose?

    - by Earlz
    Hello, while doing some homework in my very strange C++ book, which I've been told before to throw away, had a very peculiar code segment. I know homework stuff always throws in extra "mystery" to try to confuse you like indenting 2 lines after a single-statement for-loop. But this one I'm confused on because it seems to serve some real-purpose. basically it is like this: int counter=10; ... if(pow(floor(sqrt(counter+0.0)),2) == counter) ... I'm interested in this part especially: sqrt(counter+0.0) Is there some purpose to the +0.0? Is this the poormans way of doing a static cast to a double? Does this avoid some compiler warning on some compiler I do not use? The entire program printed the exact same thing and compiled without warnings on g++ whenever I left out the +0.0 part. Maybe I'm not using a weird enough compiler? Edit: Also, does gcc just break standard and not make an error for Ambiguous reference since sqrt can take 3 different types of parameters? [earlz@EarlzBeta-~/projects/homework1] $ cat calc.cpp #include <cmath> int main(){ int counter=0; sqrt(counter); } [earlz@EarlzBeta-~/projects/homework1] $ g++ calc.cpp /usr/lib/libstdc++.so.47.0: warning: strcpy() is almost always misused, please use strlcpy() /usr/lib/libstdc++.so.47.0: warning: strcat() is almost always misused, please use strlcat() [earlz@EarlzBeta-~/projects/homework1] $

    Read the article

  • undefined method `content_type' for nil:NilClass /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2

    - by Y Kamesh Rao
    Strange error in diagnostics.erb file about _set_controller_content_type. Please help. NoMethodError in Timelines#public_timeline Showing /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/templates/rescues/diagnostics.erb where line # raised: undefined method `content_type' for nil:NilClass Extracted source (around line #): RAILS_ROOT: /Volumes/DATA/Source/Rails/tvider Application Trace | Framework Trace | Full Trace /opt/local/lib/ruby1.9/gems/1.9.1/gems/activesupport-2.3.5/lib/active_support/whiny_nil.rb:52:in method_missing' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/base.rb:331:in_set_controller_content_type' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/renderable.rb:32:in block in render' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/base.rb:306:inwith_template' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/renderable.rb:30:in render' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/template.rb:205:inrender_template' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_view/base.rb:265:in render' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/rescue.rb:134:inrescue_action_locally' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/rescue.rb:152:in rescue_action_without_handler' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/rescue.rb:74:inrescue_action' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/rescue.rb:162:in rescue in perform_action_with_rescue' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/rescue.rb:160:inperform_action_with_rescue' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/flash.rb:146:in perform_action_with_flash' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/base.rb:532:inprocess' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/filters.rb:606:in process_with_filters' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/base.rb:391:inprocess' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/base.rb:386:in call' /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib/action_controller/routing/route_set.rb:437:incall' Request Parameters: None Show session dump Response Headers: {"Cache-Control"="no-cache", "Content-Type"=""}

    Read the article

  • Question about mixing MEF and Unity

    - by Dave
    I'm finally diving into Unity head first, and have run into my first real problem. I've been gradually changing some things in my app from being MEF-resolved to Unity-resolved. Everything went fine on the application side, but then I realized that my plugins were not being loaded. I started to look into this issue, and I believe it's a case where MEF and Unity don't mix. Plugins are loaded by MEF, but each plugin needs to get access to the shared libraries in my application, like app preferences, logging, etc. Initially, my plugin constructor had the ImportingConstructor attribute. I then replaced it with InjectionConstructor so that Unity could resolve its shared library dependencies. But because I did that, MEF no longer loaded it! Then I used both attributes, which compiled, but then I got a composition error (MEF). I figured that this was because the constructor takes a parameter that was once resolved by a MEF Import, so I removed all parameters. As expected, now MEF was able to load my plugin, but because the constructor needs to call into the interface that was once passed in, construction fails. So now I'm at a point where I can get MEF to start to load my plugin, but can't do anything with it because the plugin relies on shared libraries that are registered with Unity. For those of you that have successfully mixed MEF and Unity, how do you go about resolving the references to the shared libraries with Unity? It seems like a catch-22, where in order to have Unity work with the plugin, I'd have to create the plugin via Resolve, but then it's impossible to use MEF. UPDATE I can work around this problem by using an ImportingConstructor for the plugin that takes an IUnityContainer, and then call Resolve for each interface that I need, but although it works, it is incredibly lame to do it this way, as this would require all plugin authors to remember to save a reference to the passed in IUnityContainer...

    Read the article

  • simple jquery fetch from mysql

    - by JPro
    I am trying to use jQuery with MYSQL and I wrote something like this : <html> <head> <script type="text/javascript" src="http://ajax.googleapis.com/ajax/libs/jquery/1.3.2/jquery.min.js"></script> <script> function example_ajax_request() { $('#example-placeholder').html('<p>Loading results ... <img src="ajax-loader.gif" /></p>'); $('#example-placeholder').load("loadres.php"); } </script> </head> <body> <div id="query"> <select name="show" id="box" > <option value="0">Select A Test</option> <option value="All">--All--</option> <option value="M1">Model1</option> </select> <input type="button" onclick="example_ajax_request()" value="Click Me!" /> </div> <div id="example-placeholder"> <p>Placeholding text</p> </div></body> </html> Basically I want to pass parameters to the loadres.php file. But unable to figure out the exact way to do. Any help is appreciated. Thanks.

    Read the article

  • Why is an Add method required for { } initialization?

    - by Dan Tao
    To use initialization syntax like this: var contacts = new ContactList { { "Dan", "[email protected]" }, { "Eric", "[email protected]" } }; ...my understanding is that my ContactList type would need to define an Add method that takes two string parameters: public void Add(string name, string email); What's a bit confusing to me about this is that the { } initializer syntax seems most useful when creating read-only or fixed-size collections. After all it is meant to mimic the initialization syntax for an array, right? (OK, so arrays are not read-only; but they are fixed size.) And naturally it can only be used when the collection's contents are known (at least the number of elements) at compile-time. So it would almost seem that the main requirement for using this collection initializer syntax (having an Add method and therefore a mutable collection) is at odds with the typical case in which it would be most useful. I'm sure I haven't put as much thought into this matter as the C# design team; it just seems that there could have been different rules for this syntax that would have meshed better with its typical usage scenarios. Am I way off base here? Is the desire to use the { } syntax to initialize fixed-size collections not as common as I think? What other factors might have influenced the formulation of the requirements for this syntax that I'm simply not thinking of?

    Read the article

  • Multiple dynamic timers

    - by Rickard
    I am working on a project where I need to let the user create one (or more) timers to fire off an event. The user is supposed to define variables such as if the timer should be active and how often the timer will fire along with some other variables of what will happen when the timer is fiering. All these variables are stored in a dictionary (Disctionary) where the object holds all the variables the user has set and the string is the name that the user has chosen for this timer. I then want my program to loop through this dictionary and search for all objects which has the variable t_Active set to true (this I have already achieved). What I need help with figuring out is the follwoing: When it detects the variable, and if it's set to true, I need the program to see if there is already a timer created for this. If it isn't, it should create one and set the relevant parameters for the timer. The two variables t_num and t_period should decide the interval of the timer. t_num is an int and t_period is a string which will be set to either minutes, hours or days. Combining t_num with 60000 (minutes), 3600000 (hours) or 86400000 should give the corrct interval. But how would I go on about programatically create a timer for each user-defined active object? And how do I get the program to detect wether or not a timer has already been created? I have been searching both here and on google, but so far I haven't come across something that makes sense to me. I am still learning C#, so what make sense to you guys may not neccessarilly make sense to me yet. :) I hope I have explaned what I need good enough, please do ask me to clarify if you don't get me. Edit: Maybe I should also mention that the mentioned dictionary will also be saved to an XML file to that the user can pick up all the settings they made at any time.

    Read the article

  • How to get interpolated message in NHibernate.Validator

    - by SztupY
    Hi! I'm trying to integrate NHibernate.Validator with ASP.NET MVC client side validations, and the only problem I found is that I simply can't convert the non-interpolated message to a human-readable one. I thought this would be an easy task, but turned out to be the hardest part of the client-side validation. The main problem is that because it's not server-side, I actually only need the validation attributes that are being used, and I don't actually have an instance or anything else at hand. Here are some excerpts from what I've been already trying: // Get the the default Message Interpolator from the Engine IMessageInterpolator interp = _engine.Interpolator; if (interp == null) { // It is null?? Oh, try to create a new one interp = new NHibernate.Validator.Interpolator.DefaultMessageInterpolator(); } // We need an instance of the object that needs to be validated, se we have to create one object instance = Activator.CreateInstance(Metadata.ContainerType); // we enumerate all attributes of the property. For example we have found a PatternAttribute var a = attr as PatternAttribute; // it seems that the default message interpolator doesn't work, unless initialized if (interp is NHibernate.Validator.Interpolator.DefaultMessageInterpolator) { (interp as NHibernate.Validator.Interpolator.DefaultMessageInterpolator).Initialize(a); } // but even after it is initialized the following will throw a NullReferenceException, although all of the parameters are specified, and they are not null (except for the properties of the instance, which are all null, but this can't be changed) var message = interp.Interpolate(new InterpolationInfo(Metadata.ContainerType, instance, PropertyName, a, interp, a.Message)); I know that the above is a fairly complex code for a seemingly simple question, but I'm still stuck without solution. Is there any way to get the interpolated string out of NHValidator?

    Read the article

  • XML Comparison?

    - by CrazyNick
    I got a books.xml file from http://msdn.microsoft.com/en-us/library/ms762271(VS.85).aspx and just saved it with two different names, removed few lines from the second file and tried to compare the files using the below powershell code: clear-host $xml = New-Object XML $xml = [xml](Get-Content D:\SharePoint\Powershell\Comparator\Comparator_Config.xml) $xml.config.compare | ForEach-Object { $strFile1 = get-Content $.source; $strFile2 = get-Content $.destination; $diff  = Compare-Object $strFile1 $strFile2; $result1 = $diff | where {$.SideIndicator -eq "<=" } | select InputObject; $result2 = $diff | where {$.SideIndicator -eq "=" } | select InputObject; Write-host "nEntries are differ in First web.config filen"; $result1 | ForEach-Object {write-host $.InputObject}; Write-host "nEntries are differ in Second web.config filen" ;$result2 | ForEach-Object {write-host $.InputObject}; $.parameters | ForEach-Object { write-host $.parameter } } and it is working perfectly and giving me the below results: Entries are differ in First web.config file < price36.95< /price < descriptionMicrosoft Visual Studio 7 is explored in depth, looking at how Visual Basic, Visual C++, C#, and ASP+ are integrated into a comprehensive development environment.< /description Entries are differ in Second web.config file < price< /price < description< /description however I wan to know the root node of the above mentioned nodes, is that possible to find? if so, how?

    Read the article

  • Covariance and Contravariance type inference in C# 4.0

    - by devoured elysium
    When we define our interfaces in C# 4.0, we are allowed to mark each of the generic parameters as in or out. If we try to set a generic parameter as out and that'd lead to a problem, the compiler raises an error, not allowing us to do that. Question: If the compiler has ways of inferring what are valid uses for both covariance (out) and contravariance(in), why do we have to mark interfaces as such? Wouldn't it be enough to just let us define the interfaces as we always did, and when we tried to use them in our client code, raise an error if we tried to use them in an un-safe way? Example: interface MyInterface<out T> { T abracadabra(); } //works OK interface MyInterface2<in T> { T abracadabra(); } //compiler raises an error. //This makes me think that the compiler is cappable //of understanding what situations might generate //run-time problems and then prohibits them. Also, isn't it what Java does in the same situation? From what I recall, you just do something like IMyInterface<? extends whatever> myInterface; //covariance IMyInterface<? super whatever> myInterface2; //contravariance Or am I mixing things? Thanks

    Read the article

  • Mysql latin1 turkish data and delphi 2010 utf8

    - by sabri.arslan
    Hello, I have tables collating latin1_general_ci and have turkish character values. And i can use this data on delphi 7+zeos with no problem. but i want to upgrade my delphi to 2010 version but zeos too slow as i saw. so i want to use odbc+ado or dbexpress solution. dbexpress solution works fine , display my data as entered and write as entered table without any change to column charset. but dbexpress has problems as i saw. for example when i select * from table which has column types as varchar,decimal,int,tinyint,text give av errors on xp systems. vista and 7 does not give any error and work fine(not fully tested). ado solution(dbgo) works fine but its not show my data as entered.its want everything be utf. but i don't want to convert my data to utf before test everything. how can i see my data as entered and write client side utf and store latin1(as zeos or dbexpress do). i was tried many other options. eg. mysql side collation and charset parameters. sorry for my bad english. i hope someone understand me. thanks.

    Read the article

  • Problems running Ruby on Rails apps on shared hosted server

    - by Evgeny
    I have problems installing any Ruby On Rails app on my shared hosted server. Mongrel shows html as plain text for all pages. The problem occurs for any app, even if I create a test empty app and add a scaffolded view without changing anything. It appears that the Mongrel crashes when trying to put cookies to the response header. The HTTP header looks incomplete, the Content-type and other parameters are missing: curl 127.0.0.1:12002/users -I HTTP/1.1 200 OK Connection: close Date: Wed, 26 May 2010 09:46:50 GMT Content-Length: 0 Here is the output from mongrel.log Error calling Dispatcher.dispatch #<NoMethodError: You have a nil object when you didn't expect it! You might have expected an instance of ActiveRecord::Base. The error occurred while evaluating nil.[]> /usr/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/cgi.rb:108:in `send_cookies' /usr/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/cgi.rb:136:in `out' /usr/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/http_response.rb:65:in `start' ruby 1.8.7 rails 2.3.8 mongrel 1.1.5 Here is the link to the test page. Has anyone seen anything like this?

    Read the article

  • How can I scale an OSMF player in ActionScript 3/Flex

    - by Greg Hinch
    I am trying to create a simple video player SWF using the open source media framework in Flex 4. I want to make it dynamically scale based on the dimensions of the video, input by the user. I am following the directions on the Adobe help site, but the video does not seem to scale properly. Depending on the size, sometimes videos play larger than the space allotted on the webpage, and sometimes smaller. The only way I have been able to get it to work properly is by including a SWF metadata tag hardcoding the width and height, but I can't use that if I want to make the player dynamically sized. My code is : package { import flash.display.Sprite; import flash.events.Event; import org.osmf.media.MediaElement; import org.osmf.media.MediaPlayer; import org.osmf.media.URLResource; import org.osmf.containers.MediaContainer; import org.osmf.elements.VideoElement; import org.osmf.layout.LayoutMetadata; public class GalleryVideoPlayer extends Sprite { private var videoElement:VideoElement; private var mediaPlayer:MediaPlayer; private var mediaContainer:MediaContainer; private var flashVars:Object; public function GalleryVideoPlayer() { if (stage) init(); else addEventListener(Event.ADDED_TO_STAGE, init); } private function init(e:Event = null):void { removeEventListener(Event.ADDED_TO_STAGE, init); flashVars = loaderInfo.parameters; mediaPlayer = new MediaPlayer(); videoElement = new VideoElement(new URLResource(flashVars.file)); mediaContainer = new MediaContainer(); var layoutMetadata:LayoutMetadata = new LayoutMetadata(); layoutMetadata.width = Number(flashVars.width); layoutMetadata.height = Number(flashVars.height); videoElement.addMetadata(LayoutMetadata.LAYOUT_NAMESPACE, layoutMetadata); mediaPlayer.media = videoElement; mediaContainer.addMediaElement(videoElement); addChild(mediaContainer); } }}

    Read the article

  • WYSIHAT Photos upload not working - Paperclip - Ruby on Rails

    - by bgadoci
    I just successfully installed WysiHat in my rails blog. Seems that the 'add a picture' feature is not working. It successfully allows me to find and select a picture from my desktop but upon clicking save, it does nothing. I also have Paperclip successfully installed. I am wondering if this may have something to do with it. Perhaps Paperclip is getting in the way, or, perhaps I need to connect Paperclip and WysiHat somehow. Any ideas? (let me know if I need to post any code). Also, WysiHat-engine uses facebox, not sure if that is relevant. UPDATE: Added Server Log, looks like paperclip is saving it so not sure what else is going wrong. Processing PostsController#update (for 127.0.0.1 at 2010-04-23 16:42:14) [PUT] Parameters: {"commit"=>"Update", "post"=>{"body"=>"<p>Duis autem vel eum iriure dolor in hendrerit in vulputate velit esse molestie consequat, vel illum dolore eu feugiat nulla facilisis at vero eros et accumsan et iusto odio dignissim qui blandit praesent luptatum zzril delenit augue duis dolore te feugait nulla facilisi. Lorem ipsum dolor sit amet, consectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat.</p>", "title"=>"Rails Code for Search"}, "authenticity_token"=>"hndm6pxaPLfgnSMFAmLDGNo86mZG3XnlfJoNOI/P+O8=", "id"=>"105"} Post Load (0.2ms) SELECT * FROM "posts" WHERE ("posts"."id" = 105) Post Update (0.3ms) UPDATE "posts" SET "updated_at" = '2010-04-23 21:42:14', "body" = '<p>Duis autem vel eum iriure dolor in hendrerit in vulputate velit esse molestie consequat, vel illum dolore eu feugiat nulla facilisis at vero eros et accumsan et iusto odio dignissim qui blandit praesent luptatum zzril delenit augue duis dolore te feugait nulla facilisi. Lorem ipsum dolor sit amet, consectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat.</p>' WHERE "id" = 105 [paperclip] Saving attachments. Redirected to http://localhost:3000/posts/105 Completed in 12ms (DB: 0) | 302 Found [http://localhost/posts/105]

    Read the article

  • Lazarus - why I can't assign event to run-time component?

    - by Garret Raziel
    Hello, I have this Lazarus program: unit Unit2; {$mode objfpc}{$H+} interface uses Classes, SysUtils, FileUtil, LResources, Forms, Controls, Graphics, Dialogs, StdCtrls, ComCtrls; type { TForm2 } TForm2 = class(TForm) procedure OnTlacitkoClick(Sender: TObject); procedure FormClose(Sender: TObject; var CloseAction: TCloseAction); procedure FormCreate(Sender: TObject); tlac:TButton; private { private declarations } public { public declarations } end; var Form2: TForm2; implementation { TForm2 } procedure TForm2.OnTlacitkoClick(Sender: TObject); begin showmessage('helloworld'); end; procedure TForm2.FormCreate(Sender: TObject); var i,j:integer; begin tlac:=TButton.Create(Form2); tlac.OnClick:=OnTlacitkoClick; tlac.Parent:=Form2; tlac.Left:=100; tlac.Top:=100; end; initialization {$I unit2.lrs} end. but compiler says: unit2.pas(63,32) Error: Wrong number of parameters specified for call to "OnTlacitkoClick" in tlac.OnClick:=OnTlacitkoClick; expression. I have searched and think that this is legal expression in Delphi. I want simply to registrate OnTlacitkoClick as tlac.OnClick event,not to call this procedure. Is there somethink wrong with the code or must I do it different in Lazarus/Freepascal? Thanks.

    Read the article

< Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >