Search Results

Search found 38274 results on 1531 pages for 'getting started'.

Page 292/1531 | < Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Percona-server time out on /etc/init.d/mysql start

  - by geekmenot

  Every time I start mysql, using /etc/init.d/mysql start or service mysql start, it always times out. * Starting MySQL (Percona Server) database server mysqld [fail] However, I can get into mysql. Just wanted to know if there is a problem with the install because it happens all the time, not a one off error. mysql-error.log shows: 121214 11:25:56 mysqld_safe Starting mysqld daemon with databases from /data/mysql/ 121214 11:25:56 [Note] Plugin 'FEDERATED' is disabled. 121214 11:25:56 InnoDB: The InnoDB memory heap is disabled 121214 11:25:56 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121214 11:25:56 InnoDB: Compressed tables use zlib 1.2.3 121214 11:25:56 InnoDB: Using Linux native AIO 121214 11:25:56 InnoDB: Initializing buffer pool, size = 14.0G 121214 11:25:58 InnoDB: Completed initialization of buffer pool 121214 11:26:01 InnoDB: Waiting for the background threads to start 121214 11:26:02 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.2 started; log sequence number 9333955393950 121214 11:26:02 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121214 11:26:02 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121214 11:26:02 [Note] Server socket created on IP: '0.0.0.0'. 121214 11:26:02 [Note] Slave SQL thread initialized, starting replication in log 'mysql-bin.005163' at position 624540946, relay log '/data/mysql/mysql-relay-bin.000043' position: 624541092 121214 11:26:02 [Note] Slave I/O thread: connected to master '[email protected]:3306',replication started in log 'mysql-bin.005180' at position 823447620 121214 11:26:02 [Note] Event Scheduler: Loaded 0 events 121214 11:26:02 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.2-log' socket: '/data/mysql/mysql.sock' port: 3306 Percona Server (GPL), Release 29.2

  Read the article

• Error during SSL installation cPanel/WHM

  - by baswoni

  I have a dedicated server and I am using the install wizard via WHM to install an SSL certificate. I have the following keys: Certificate key RSA private key CA certificate I paste these three elements into the wizard along with the domain, IP address and username but I get this error: SSL install aborted due to error: Unable to save certificate key. Certificate verification passed Have I missed a step? I have given it another go to make sure I am copying and pasting the info correctly and I am now getting the following error: SSL install aborted due to error: Sorry, you must have a dedicated ip to use this feature for the user: username! If you are intending to install a shared certificate you must use the username "nobody" for security and bandwidth reporting reasons. Even though I am using a dedicated IP address, I am getting this problem. I thought I would also add that this SSL certificate has been installed on a shared hosting environment with my previous hostig provider. The account with them is still active, however the domain and its contents now reside on the dedicated server - could this cause problems?

  Read the article

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• How to create a new background process in a KSH "while read" loop?

  - by yael

  The following test script has a problem. When I add the line (sleep 5 ) & in the script then the "while read" loop does not read all lines from the file, but only prints the first line. But when I remove the ( sleep 5 ) & from the script, then the script prints all lines as defined in the file. Why the ( sleep 5 ) & causes this? And how to solve the problem? I want to create a new process (for which the sleep is just an example) in the while loop: $ more test #!/bin/ksh while read -r line ; do echo Read a line: echo $line ( sleep 5 )& RESULT=$! echo Started background sleep with process id $RESULT sleep 1 echo Slept for a second kill $RESULT echo Killed background sleep with process id $RESULT done < file echo Completed On my Linux, when using the following contents of file: $ more file 123 aaa 234 bbb 556 ccc ...running ./test just gives me: Read a line: 123 aaa Started background sleep with process id 4181 Slept for a second Killed background sleep with process id 4181 Completed

  Read the article

• Fresh 12.04 Install - mySQL not starting

  - by Lee Armstrong

  I have a freshly installed Ubuntu 12.04 x64 server and I installed Percona server from their official repositories. Trouble is it will not start! mysql-error.log shows nothing obvious. 121129 12:16:54 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql/ 121129 12:16:54 [Note] Plugin 'FEDERATED' is disabled. 121129 12:16:54 InnoDB: The InnoDB memory heap is disabled 121129 12:16:54 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121129 12:16:54 InnoDB: Compressed tables use zlib 1.2.3 121129 12:16:54 InnoDB: Using Linux native AIO 121129 12:16:54 InnoDB: Initializing buffer pool, size = 12.0G 121129 12:16:54 InnoDB: Completed initialization of buffer pool 121129 12:16:54 InnoDB: highest supported file format is Barracuda. 121129 12:16:55 InnoDB: Waiting for the background threads to start 121129 12:16:56 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.1 started; log sequence number 1598476 121129 12:16:56 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121129 12:16:56 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121129 12:16:56 [Note] Server socket created on IP: '0.0.0.0'. 121129 12:16:56 [Note] Event Scheduler: Loaded 0 events 121129 12:16:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.1-log' socket: '/var/run/mysqld/mysql.sock' port: 3306 Percona Server (GPL), Release 29.1 121129 12:16:56 [Note] Event Scheduler: scheduler thread started with id 1 And the syslog shows... Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: #007/usr/bin/mysqladmin: connect to server at 'localhost' failed Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: The socket file is being created and I can access the server NOT using the socket using mysql -h 127.0.0.1 -P 3306 -u root --pPASSWORD

  Read the article

• Disk usage on IIS, PHP5, performance problems.

  - by Jacob84

  Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

  Read the article

• How to go about rotating logs which are arbitrary named and placed in deeply nested directories?

  - by Roman Grazhdan

  I have a couple of hosts which are basically a playground for developers. On these hosts, each of them has a directory under /tmp where he is free to do all he wants - store files, write logs etc. Of course, the logs are to be rotated, or else the disc will be 100% full in a week. The files can be plenty, but I've dealt with it with paths like /tmp/[a-e]*/* and so on and lived happily for a while, but as they try new cool stuff on the machine logrotate rules grow ugly and unmanageable, and it's getting more difficult to understand which files hit the glob. Also, logrotate would segfault if asked to rotate a socket. I don't feel like trying to enforce some naming policies in that environment, I think it's going to take quite a lot of time and get people annoyed and still would fail at some point. And I still need to manage the logs, not just rm the dirs at night. So is it a good idea in circumstances like these to write a script which would handle these temporary files? I prefer sticking with standard utilities whenever possible, but here I think logrotate is getting less and less manageable. And probably someone heard of some logrotate alternatives which would work well in such an environment? I don't need emailing logs or some other advanced features, so theoretically some well commented find | xargs would do. P.S. I do have a log aggregator but this stuff is not going to touch my little cute logstash machine.

  Read the article

• SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

  - by eulerfx

  I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

  Read the article

• Very slow context menu in Windows 8

  - by burzum

  I've installed Windows 8 Pro on a blank new SSD, the system is on c:\. I do not think this problem was existent when I started using Windows 8 but I think it started to happen after I've symlinked (mklink /D) a folder from another drive, a SATA drive, to c:\xampp\htdocs. When I right click a file or folder inside the symlinked folder it always takes at least ~5-10 seconds until the context menu comes up. This also happens sometimes, but not all the time for files and folder outside of the symlinked folder. Also when I delete folders the delete folder dialog seems to get locked and does not continue. When I delete a folder using rmdir from the command line it works fine and pretty fast. It appears to me like the file explorer in Windows 8 is pretty bad compared to any other Windows I've used before? Any idea how to get these problems solved? I've already removed a lot of context menu entries; the only ones left are the tortoise git context menus but I'm sure that's not the problem.

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• Terminal emulation has stopped working. Garbage escape chars

  - by oligofren

  To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

  Read the article

• dom0 enable IPv6 for guests

  - by user98651

  I am looking at deploying IPv6 to my virtual machines. Right now I have v6 working great on the dom0 using a 6in4 provided by Hurricane Electric as I do not have native v6. However, I would like to distribute some of the /48 I am receiving to the domUs (/64 per machine would be ideal, but I am open to your suggestions). Static configuration on the domU side is fine. All I want to accomplish is getting the traffic to pass through the dom0 to the domU. To say the least, I'm still trying to wrap my head around all the virtual interfaces and bridges Xen creates. Yes, I have Googled around for this a bit and have not found anything great. I tried using two "vif-route6" bash scripts with no luck (possibly due to my ignorance with Xen networking). I am still stuck (mainly in how to configure the dom0). I would like to imagine this problem is relatively easy to solve and I look forward to your suggestions and help! Edited post to clarify my end goal: getting IPv6 to domU guests. I am completely open to suggestions but am hoping for something other than setting up a tunnel for every guest.

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• Ngix rewrite is not working as expected

  - by SamFisher83

  I am trying to learn how to use nginx and how to use its rewrite functionality Nginx seems to be doing the rewrite: 2012/03/27 16:30:26 [notice] 16216#0: *3 "foo.php" matches "/foo.php", client: 61.90.22.223, server: localhost, request: "GET /foo.php HTTP/1.1", host: "domain.com" 2012/03/27 16:30:26 [notice] 16216#0: *3 rewritten data: "img.php", args: "", client: 61.90.22.223, server: localhost, request: "GET /foo.php HTTP/1.1", host: "domain.com" but in my access log I am getting the following: 61.90.22.223 - - [27/Mar/2012:16:26:54 +0000] "GET /foo.php HTTP/1.1" 404 31 "-" "Mozilla/5.0 (Windows NT 6.1; rv:11.0) Gecko/20100101 Firefox/11.0" 61.90.22.223 - - [27/Mar/2012:16:30:26 +0000] "GET /foo.php HTTP/1.1" 404 31 "-" "Mozilla/5.0 (Windows NT 6.1; rv:11.0) Gecko/20100101 Firefox/11.0" There is an img.php in the root directory so I am not sure why I am getting a 404 error Here is part of the configuration block: rewrite foo.php img.php last; location / { try_files $uri $uri/ /index.html; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; }

  Read the article

• Virus cleanup; Windows Automatic Updates service crashes in esent.dll

  - by quack quixote

  Background I'm doing system recovery on an old WinXP SP1 system brought to me on suspicion of virus infection. After taking preliminary backups, I used MalwareBytes to detect and clean the infection. I might've even gotten it all. In the process, I've discovered (a) the system drive is showing signs of impending failure, and (b) the owner has been using the system's old crusty IE-6 instead of the up-to-date Firefox I've provided for him. So naturally, thinking I had a relatively stable system, I tried to hit the Windows Update site to install IE-8, in case further training doesn't stick. The update site told me it needed to update the installer, and I started that process. Soon after, wuauclt.exe started crashing, reporting addresses in module esent.dll. There's a Microsoft KB (910437) on a problem with that DLL, so I downloaded the hotfix and installed. The crashing did not stop. I attempted to install SP3 from the offline installer, but that didn't fix the issue either. The system is reporting a few hard drive / IDE controller errors, but they don't correlate to the crashes, so they aren't the direct cause. I've also attempted to rollback to the time between the infection removal and the first crashes, but that doesn't help. Question The hotfix I tried to install dealt with problem in transaction logs of the Extensible Storage Engine (ESE) database. I suspect this issue is similar, but that the database itself (whatever the ESE database is) is corrupted. Is there a way to clean or clear this database so that system operation returns to normal? Can someone enlighten me as to what the ESE database actually is, and where it resides? Can I just locate some files and delete them to bring this under control?

  Read the article

• Managing persistent data on an Amazon EC2 web server

  - by Derek

  I've just started trying out Amazon's EC2 service for running an asp.net web app which uses a SQL Server 2005 Express database. I have some questions about how to configure and operate it best for reliability, and I'm hoping to tap into some collective wisdom here as this is my first foray into EC2. Here's how I have it configured currently: OS: Windows 2003 SQL Server Express 2005 Web content stored on an EBS Volume (E Drive) Database Data stored on an EBS Volume (E Drive) Database backups to "C Drive" and then copied off to S3. Elastic IP Address attached to the production instance. Now when I make a change to the OS configuration, I make a new AMI using the bundle feature. Unfortunately, I found that this results in significant downtime. While the bundle is created and the new instance is started. It seems that when I'm ready to make a new AMI, I should: Start up a new temporary instance. Detach the EBS volume from the production instance. Detach the IP Address from the production instance. Attach the IP Address to the temporary instance. Attach the EBS volume to the temporary instance. Create an AMI from the production instance. After the production instance restarts, reverse the attach/detach steps to put it back in production. Is this the right order of events to prevent any chance to corrupt the EBS volume? Will the EBS volume become corrupt if I detach it while a database Write is taking place? Should I snapshot the EBS volume of the production instance and attach it to the temporary instance instead? Or could taking a snapshot of the EBS volume while it's in use cause corruption? Any suggestions to improve the reliability and operations?

  Read the article

• Strange sound behavior

  - by caarlos0

  First of all, sorry for the tittle. English isn't my native language, and I can't find a word to describe the strange behavior I'm getting here. In the most simple explanation, is like sound keeps going down and up again... Think in a kid with that old radios that have a circled volume button. Think like these kid keeps "turning" the volume button. That is the behavior I'm getting here. At first, I believed that it was a pulseaudio issue, but, it isn't. I followed the wiki part I think that should be my problem, but it didn't work. After that, as I'm using XFCE, I didn't really need pulseaudio, so I removed it and stays with a clean alsa, hopping that will fix my problem. Sweet mistake. It really looks like a kid looking for trouble. I believed it worked, and, suddenly, here is the same issue again. BTW: I have a full-upgraded testing system (yeah, I upgraded to testing hopping for new pulseaudio version which fix the issue), no pulseaudio at all, just xfce, started with startxfce. What can I do to fix this? It's extremely annoying... sometimes I just want to throw my laptop in the wall because of this. Any extra info you need, please, tell me. Thanks in advance -- EDIT: My alsamixer is like this: And here is a video with the sound behavior.

  Read the article

• No boot device found. Press any key to continue

  - by Andrew Banks

  I took out the hard drive from my Dell Latitude E5420 notebook, put in an ADATA S599 solid state drive, and installed Ubuntu 11.10. When I boot, the Dell BIOS splash screen appears with a progress bar, which quickly fills up, and the screen goes black. All of this is like it was before. At this point, the OS splash screen should fade in. Instead, I was dismayed to see simply the following, in white text on a black screen: No boot device found. Press any key to continue After looking around for the Any key (just kidding) I press a key, and the Dell BIOS splash screen appears again with a progress bar, which quickly fills up, and the screen goes black. This time, however, the Ubuntu splash screen shows up, Ubuntu opens up, and all is normal. Every time I shut down, however, this happens again. It's like a game the computer and I play together. The computer has never started up without first saying: No boot device found. Press any key to continue and it has always started up after I press any key to continue. It also starts up fine if I click Restart instead of Shut Down. Thoughts?

  Read the article

• Exclamation 403 forbidden for cgi-bin/ and cannot protect site with password

  - by gasgdasdgasdg

  First problem i have is i am getting 403 forbidden error for cgi-bin/ I have created a new /var/www2/ i can access it fine. php runs fine. Second problem is I cannot password protect it. i first tried doing htpasswd, it asks for login but everytime i login it keeps asking for new one. its getting frustrating, i have tried all tricks. and doesn't seem to work. this is a virtual host config inside sites-available. httpd.conf is empty but i have apache2.conf Code: NameVirtualHost 12.12.12.12. <VirtualHost 12.12.12.12> ServerAdmin webmaster@localhost DocumentRoot /var/www2/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www2/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /var/www2/cgi-bin/ <Directory "/var/www2/cgi-bin/"> AllowOverride Options Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch AddHandler cgi-script cgi pl Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost>

  Read the article

• Salary Survey Entry Level network position [closed]

  - by will

  Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

  Read the article

• Windows shutting down, CPU maxing out in Windows-7 32-bit? [closed]

  - by Vivek Sharma

  I have no idea, what is happening to my laptop. For last 5-6 times it has automatically shutdown while running, without doing anything serious. And I even do get the message during boot which says - Start windows normal - Start in safe mode It just boots up normal. Few days ago, my screen blinked and it the PC shutdown immediately. After that I was not able to get it started. I got it repaired, the guy said he has replaced the display chip (nVidia-nvs-140), but i seriously doubt that. Now it started working, but would shutdown every 20 mins or so. I have a dual boot, ubuntu-11.10 works just fine. Virus scan on windows shows nothing. I am pasting my perfmon output. My CPU for reason is maxing out to 100% continously, for windows internal processes. Please have a look at the attached file. Strangly now for last 2 hours it is working fine, but i am just writing emails and reading excels. ThinkPad T61 | t9300 | 3gb | nVidia 140 nvs-quadro (latest driver 296.10) What do you suggest?

  Read the article

• BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

  - by DontCare4Free

  I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

  Read the article

• Enter network credentials as part of batch script

  - by Michael

  WinXP: I have several system services that are needed to run some machinery in my lab. The machine these services are running uses a lab login that has administrator rights. Our IS department, unfortunately, has it set up where at some point during the night the login "loses" the privilege level to start/stop these services. The account stays logged in, but the software controlling my hardware becomes unresponsive. In order to get things back up and running, I have to stop the system services and restart them. Because of the security settings, however, I have to re-enter the user password to start the service (even though the user was never logged out). That, I get the "This service cannot be started due to a logon failure" and I have to enter the password. What would be ideal is to have a batch script run before anyone gets into work that stops all of the necessary services, enters the user credentials when prompted, and then restarts them so that everything is ready for first shift to run. I assumed that using the Task Scheduler in Windows would work as it allows you to run batch files with a user's name and password, but this didn't seem to do the trick. With this setup I would arrive to find that all the services are stopped but not started again. (Presumably because the authentication failed.) The batch file is about as simple as it gets, all I have is: net stop "Service1" net stop "Serivce2" etc., then restart in reverse order based on dependency: net start "Service2" net start "Serivce1" What would it take to accomplish what I'm trying to do and restart the services?

  Read the article

• HP tx2510us shuts down without warning, now won't boot, no BIOS codes, screen doesn't light

  - by Tim S

  Hey all, HP tx2150us worked great for a year and a half, rarely it would shut down instead of sleeping. It started running hot sometimes, I installed Win7, worked great, still running hot. Before Xmas, it gave me evidence of video errors - jagged lines, rows missing. That same night, it started rebooting, then it shut off and wouldn't boot. It gave me a BIOS code, I shut it off to look up the code online. When I turned it on again, it won't boot at all. The LEDs all light up, the fan, HD, and optical all spin up, but the screen never lights up and it doesn't try to boot, nor does it blink any BIOS codes. It just acts like it's sleeping, and won't wake up. I suspected heat problems, so I disassembled it, cleaned the crap out of the fan, and reassembled it, breaking the stereo mic connector. Oh well. When I reassembled it, it booted up into Win7 again, but kept shutting down for no discernible reason. After a dozen or so random reboots like that, it is now back to where it was - turns on but doesn't boot or give BIOS codes. The screen never lights, and everything spins up then idles. Any ideas? I really can't afford to buy a new one and I use(d) it to take ALL my notes, that's why I got a tablet in the first place.

  Read the article

< Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >