Search Results

Search found 38274 results on 1531 pages for 'getting started'.

Page 288/1531 | < Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >

  • Slow network file transfer (under 20KB/s) on newly built x64 Win7

    - by Mangoshake
    I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

    Read the article

  • Open Source Chef Server can't upload cookbook

    - by veilig
    I just setup the open source chef server on an Ubuntu 12.04 EC2 instance, I've setup my webui and am able to get responses from my knife commands ie: knife node list, knife client list, knife user list, etc... I'm able to update roles, databags, environments, etc... but I cannot upload any cookbooks. I'm running my workstation on Mac OSX. I keep getting this output at the end of my command knife cookbook upload -VV curl. Doesn't matter what cookbook I upload, or if I upload them all - I keep getting the same response DEBUG: Chef::HTTP calling Chef::HTTP::ValidateContentLength#handle_response DEBUG: Chef::HTTP calling Chef::HTTP::RemoteRequestID#handle_response DEBUG: Chef::HTTP calling Chef::HTTP::Authenticator#handle_response DEBUG: Chef::HTTP calling Chef::HTTP::Decompressor#handle_response DEBUG: Chef::HTTP calling Chef::HTTP::CookieManager#handle_response DEBUG: Chef::HTTP calling Chef::HTTP::JSONToModelOutput#handle_response /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http/json_output.rb:51:in `handle_response': undefined method `chomp' for nil:NilClass (NoMethodError) from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:229:in `block in apply_response_middleware' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:227:in `each' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:227:in `inject' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:227:in `apply_response_middleware' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:144:in `request' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/http.rb:118:in `put' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/cookbook_uploader.rb:123:in `block in uploader_function_for' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/util/threaded_job_queue.rb:52:in `call' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/util/threaded_job_queue.rb:52:in `block (3 levels) in process' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/util/threaded_job_queue.rb:50:in `loop' from /usr/local/lib/ruby/gems/2.1.0/gems/chef-12.0.0.alpha.1/lib/chef/util/threaded_job_queue.rb:50:in `block (2 levels) in process'INFO: HTTP Request Returned 204 No Content:

    Read the article

  • Problem with PXE boot

    - by user70523
    I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

    Read the article

  • Windows XP restarting repeatedly after a fresh restore

    - by DWilliams
    I don't normally deal with Windows but someone wanted me to fix their computer with Windows XP on it. It was just restarting every time it tried to boot. It would not go into safe mode, the result was the same regardless of the selected mode. The computer is like 4 years old and has been running the same installation for that entire time, so I figured the easiest solution was just to back up their files and re-install. I loaded the computer up with a live CD and copied their files off to a USB drive, then proceeded to run HP's "factory restore" feature (which I'm not particularly fond of, I'd rather have a disk to install from than reload all the crapware HP gets paid to install for you). It restored, and I put all their files back, installed their programs, and started the full windows update process. Everything seemed great so I left and told them what to do once it finished. A few hours pass, and my phone rings. Apparently it started doing the exact same thing as before once the updates finished. I don't have the computer sitting in front of me now so I can't really provide any more information than that. What could be causing this and, more importantly, how do I fix it? The fact that the same problem resurfaced after the restore makes me think it's either a hardware problem or an update breaking the computer.

    Read the article

  • Failed to su after making a chroot jail

    - by arepo21
    On a 64 bit CentOS host I am using script make_chroot_jail.sh to put a user in a jail, not permitting it to see anything expect it's home at /home/jail/home/user1. I did it typing this: sudo ./make_chroot_jail.sh user1 after, when trying to connect to user1 first i was getting an error like: /bin/su: user guest does not exist i have fixed this by copying some missed libraries: sudo cp /lib64/libnss_compat.so.2 /lib64/libnss_files.so.2 /lib64/libnss_dns.so.2 /lib64/libxcrypt.so.2 /home/jail/lib64/ sudo cp -r /lib64/security/ /home/jail/lib64/ But now, when trying to connect to user1 typing su user1 and then typing it's password, i am getting this error: could not open session So the question is how to connect to user1 in this situation? P.S. Here are the permissions of some files, this might be helpful in order to provide a solution: -rwsr-xr-x 1 root root /home/jail/bin/su drwxr-xr-x 4 root root /home/jail/etc -rw-r--r-- 1 root root /home/jail/etc/pam.d/su -rw-r--r-- 1 root root /home/jail/etc/passwd -rw------- 1 root root /home/jail/etc/shadow UPDATE1 After some modifications i managed to connect to user1, but the session closes immediately! I guess this a PAM issue, however cant find a way to fix it. Here the log entry for close action from /val/log/secure: Oct 6 15:19:42 localhost su: pam_unix(su:session): session closed for user user1 What makes the session to exit immediately after launching?

    Read the article

  • Server extremely lags and logs bunch of 'internal dummy connection'

    - by Dmitry
    Having a web-server (don't know actually whoset it up, it's my heritage). Few hours ago it started working very (extremely!) slow, mysqld oftenly fails requests. /var/log/mysqld.log is empty (well, it says, mysqld started, and so on, but nothing regarding today) /var/log/apache2/access_log is full of such lines: ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" ::1 - - [30/Nov/2011:10:15:05 +0100] "GET / HTTP/1.0" 200 1 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)" Guys, what's that? How to heal this? I read internal dummy connections happen sometimes, but sending internal requests at 1000/sec frequency isn't freaking normal!How to find out the reason of this?

    Read the article

  • django : Serving static files through nginx

    - by PlanetUnknown
    I'm using apache+mod_wsgi for django. And all css/js/images are served through nginx. For some odd, reason when others/friends/colleagues try accessing the site, jquery/css is not getting loaded for them, hence the page looks jumbled up. My html files use code like this - <link rel="stylesheet" type="text/css" href="http://x.x.x.x:8000/css/custom.css"/> <script type="text/javascript" src="http://1x.x.x.x:8000/js/custom.js"></script> My nginx configuration in sites-available is like this - server { listen 8000; server_name localhost; access_log /var/log/nginx/aa8000.access.log; error_log /var/log/nginx/aa8000.error.log; location / { index index.html index.htm; } location /static/ { autoindex on; root /opt/aa/webroot/; } } There is a directory /opt/aa/webroot/static/ which have corresponding css & js directories. The odd thing is that the pages show fine when I access them. I have cleared my cache/etc, but the page loads fine for me, from various browsers. Also, I don't see any 404 any error in the nginx log files. Actually the logs for nginx are not getting refreshed at all. I restarted the nginx server using root, is that incorrect ? There is a user www-data defined in the nginx configuration file. Any pointers would be great.

    Read the article

  • I am under DDoS. What can I do?

    - by Falcon Momot
    This is a Canonical Question about DoS and DDoS mitigation. I found a massive traffic spike on a website that I host today; I am getting thousands of connections a second and I see I'm using all 100Mbps of my available bandwidth. Nobody can access my site because all the requests time out, and I can't even log into the server because SSH times out too! This has happened a couple times before, and each time it's lasted a couple hours and gone away on its own. Occasionally, my website has another distinct but related problem: my server's load average (which is usually around .25) rockets up to 20 or more and nobody can access my site just the same as the other case. It also goes away after a few hours. Restarting my server doesn't help; what can I do to make my site accessible again, and what is happening? Relatedly, I found once that for a day or two, every time I started my service, it got a connection from a particular IP address and then crashed. As soon as I started it up again, this happened again and it crashed again. How is that similar, and what can I do about it?

    Read the article

  • OpenSwan (IPSEC) on Fedora 13 with Snow Leopard as a client

    - by sicn
    I recently installed OpenSwan on my Fedora 13 machine. I want to use it to connect with Mac OS X with L2TP over IPSEC, unfortunately I am already stuck on the IPSEC-negotation part. My server is running behind a NATted firewall so my external IP differs from the server's IP. The server has a fixed IP on the network and the same is almost always valid for the clients (they are usually behind a NATted firewall). I installed OpenSwan on Fedora 13 and have following configuration: config setup protostack=netkey nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=my.servers.external.ip leftprotoport=17/1701 right=%any rightprotoport=17/0 IPSEC starts fine and listens to UDP 500 and 4500. These two ports are opened in the firewall and are forwarded fine to the server. In my /etc/ipsec.secrets file I have my.servers.external.ip %any: "LongAndDifficultPassword" And finally in my sysctl.conf (the redirect-entries are there because OpenSwan was strongly protesting about send/accept_redirects being active) I have net.ipv4.ip_forward = 1 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_redirects = 0 Running "ipsec verify" gives me "all greens" (except Opportunistic Encryption Support, which is DISABLED), however, when trying to connect my Mac gives me following in the logs: Nov 1 19:30:28 macbook pppd[4904]: pppd 2.4.2 (Apple version 412.3) started by user, uid 1011 Nov 1 19:30:28 macbook pppd[4904]: L2TP connecting to server 'my.servers.ip.address' (my.servers.ip.address)... Nov 1 19:30:28 macbook pppd[4904]: IPSec connection started Nov 1 19:30:28 macbook racoon[4905]: Connecting. Nov 1 19:30:28 macbook racoon[4905]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Nov 1 19:30:31 macbook racoon[4905]: IKE Packet: transmit success. (Phase1 Retransmit). Nov 1 19:30:38: --- last message repeated 2 times --- Nov 1 19:30:38 macbook pppd[4904]: IPSec connection failed Any ideas at all?

    Read the article

  • Hubs/switches taking out switches?

    - by Bart Silverstrim
    Here's the issue...we have a network with a lot of Cisco switches. Someone plugged in a hub on the network, and then we started seeing "weird" behavior; errors in communication between clients and servers, or network timeouts, dropping network connections, etc. It seemed that somehow that hub (or SOHO switch) was particularly freaking out our Cisco 3700 series switches. Disconnect that hub or netgear-type SOHO switch and things settled down again. We're in the process of trying to get a centralized logging server for SNMP and management, etc., to see if we can trap errors or narrow down when someone does this sort of thing without our knowledge because things seem to work, for the most part, without issue, we just get freaky oddball incidents on particular switches that don't seem to have any explanation until we find out someone decided to take matters into their own hands to expand available ports in their room. Without getting into procedure changes or locking down ports or "in our organization they'd be fired" answers, can someone explain why adding a small switch or hub, not necessarily a SOHO router (even a dumb hub apparently caused the 3700's to freak out) sending DHCP request out, will cause issues? The boss said it's because the Cisco's are getting confused because that rogue hub/switch is bridging multiple MAC's/IP's into one port on the Cisco switches and they just choke on that, but I thought their routing tables should be able to handle multiple machines coming into the port. Anyone see that behavior before and have a clearer explanation of what's happening? I'd like to know for future troubleshooting and better understanding that just waving my hand and saying "you just can't".

    Read the article

  • Is it possible to use rsync over sftp (without an ssh shell)?

    - by Tom Feiner
    Rsync over ssh, works great every time. However, trying to rsync to a host which allows only sftp logins, but not ssh logins, provides the following error: rsync -av /source ssh user@remotehost:/target/ protocol version mismatch -- is your shell clean? (see the rsync man page for an explanation) rsync error: protocol incompatibility (code 2) at compat.c(171) [sender=3.0.6] Here's the relevant section from the rsync man page: This message is usually caused by your startup scripts or remote shell facility producing unwanted garbage on the stream that rsync is using for its transport. The way to diagnose this problem is to run your remote shell like this: ssh remotehost /bin/true > out.dat then look at out.dat. If everything is working correctly then out.dat should be a zero length file. If you are getting the above error from rsync then you will probably find that out.dat contains some text or data. Look at the contents and try to work out what is producing it. The most com- mon cause is incorrectly configured shell startup scripts (such as .cshrc or .profile) that contain output statements for non-interactive logins. Trying this on my system produced the following in out.dat: ssh-dummy-shell: Command not allowed. As I thought, the host is not allowing ssh logins. The following link shows that it is possible to accomplish this task using fuse with sshfs - however it is extremely slow, and not fit for production use. Is there any chance of getting rsync sftp to work?

    Read the article

  • What is the fastest way to resize a large partition?

    - by Jook
    Due to a new HDD-Configuration I am currently handling larger backup/resize tasks with partitions between around 900MB, wich are 70-90% full. some background: First thing I've noticed was, that the Acronis-WesternDigital TrueImage was extremly slow while running it under Windows 7, even though on high priority. To create a normal backup for 650gb of data (900gb partition), it would have taken 3 days! The same task done with the boot-cd version of this acronis version took about 2 hours (SATA3 copy from one disk to another, both around 110MB/s). Now, after I have done all my backups, I've wanted to remove some obsolete partitions and resize the leftovers to full hdd size. Of course, usually this takes quite some time - in this case for this 900gb partition, to extend it to 931 (30gb+ from front, 1gb+ from end), it will take around 6 hours (using gparted)! Had I new that erlier, I would have just restored the image. But no - first it showed a reasonable time of 1:45h and 0 of 1 operations, but after finishing 1:45h it started again, only this time with 4h to go, still 0 of 1 operations, but now it was copying instead of moving. Question: However, why has it to be this slow to resize a partition? I am asking for a good explanaition. This has bugged me, since I started partitioning - why does it require to copy all the data around, can't it just stay in place?!

    Read the article

  • SQL Server Agent refuses to start

    - by Geo Ego
    I'm having a problem with SQL Server 2005 where the SQL Server Agent suddenly refuses to start. If I attempt to start it through Services, I get the error "SQL Server Agent (MSSQLSERVER) service on Local Computer started and then stopped." In the Application log, I have the following entry: Event Type: Error Event Source: SQLSERVERAGENT Event Category: Service Control Event ID: 103 Date: 5/20/2010 Time: 11:07:07 AM User: N/A Computer: SHAREPOINT Description: SQLServerAgent could not be started (reason: Unable to connect to server 'SHAREPOINT'; SQLServerAgent cannot start). This database has been running fine for four months. It contains a SharePoint configuration database, which two days ago stopped working, throwing me a message that the configuration database cannot be reached. It was then that I realized the SQL Server Agent was not running, and I have been unable to restart it. I have tried running it with both the local system account and the network service account, with the same results. So far, I have tried: Granting the administrators group, network service, and SharePoint SQL Server Agent account public and sysadmin roles on the database. Granting the administrators group, network service, and SharePoint SQL Server Agent account full permissions to the entire MSSQL directory and all files within. I still have no joy.

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • How do I repair a Windows 7 installation damaged by Windows 8 sleep mode

    - by Mat
    I'm experimenting with a Windows 8 installation which is on a separate SSD. My actual Windows 7 installation I'm working with is on my old HDD. While Windows 8 was in sleep mode I swapped the hard disks and put in the Windows 7 HDD (I thought the computer was off). When I started the computer, Windows 8 started back up to the login screen – then it was stuck and some seconds later the computer rebooted. Now the Windows 7 Installation is damaged. When I boot, after the Windows 7 startup logo appears, a bluescreen shows up for few seconds stating: STOP: c000021a {Fatal System Error} The verification of KnownDLL failed. System process terminated unexpectedly with a status of 0xc000012f (0x00f0bb90 0x00000000). The system has been shut down. and then the computer reboots. The same happens in safe mode. 'Windows startup repair' cannot repair the issue. Any idea what could have happened exactly and/or how to repair this Windows 7 Installation?

    Read the article

  • Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

    - by raid question
    I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

    Read the article

  • postfix says mail sent ok, message does not arrive in ISPs inbox? no reject in log?

    - by Nick
    When I send a test message from my mail server to my @bellsouth.net email, The postfix log shows it was sent OK, but the message never arrives in my bellsouth inbox. Shouldn't I get a failure notice or a bounce if At&T is blocking the messages? I'm trying to troubleshoot why some customers aren't getting emails, but if there's nothing in mail.log to say the message is rejected, how do I know which messages were delivered successfully? The log shows: Feb 27 09:02:36 MyHOSTNAME postfix/pickup[26175]: D53A72713E5: uid=0 from=<root> Feb 27 09:02:36 MyHOSTNAME postfix/cleanup[26487]: D53A72713E5: message-id=<[email protected]> Feb 27 09:02:36 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: from=<[email protected]>, size=878, nrcpt=1 (queue active) Feb 27 09:02:37 MyHOSTNAME postfix/smtp[26490]: D53A72713E5: to=<[email protected]>, relay=gateway-f1.isp.att.net[204.127.217.16]:25, delay=0.57, delays=0.11/0.03/0.23/0.19, dsn=2.0.0, status=sent (250 ok ; id=20120227140036M0700qer4ne) Feb 27 09:02:37 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: removed The AT&T server accepted the message, right? I happen to have an At&T/Bellsouth email, but I don't have an account with every ISP we send to. I need some way of knowing if a message is getting to its destination or not. Is there any setting in my main.cf file that would affect whether or not we get reject/bounce notices?

    Read the article

  • Mustek 1200 CP driver SFC4.SYS bluescreens with BAD_POOL_HEADER

    - by Slink84
    I have Windows XP SP2. Recently it started bluescreening right after starting up with 'BAD_POOL_HEADER', 0x00000019 error caused by SFC4.SYS driver. After googling for a while I've found out that this is my Mustek's 1200 CP scanner driver. Booting in safe mode and uninstalling it solved the problem... And created another one: now I can't use my scanner. The weird thing is, that it has been working for a while on this PC without any problems. It all started suddenly, and I can't remember installing anything that might have affected it. Reverting to several earlier system restore points didn't help. I've tried re-installing it from the Mustek website, just in case if my copy got corrupted or infected by a virus, but it did not help - it still bluescreens. Also, I've installed Avast and scanned my PC - there were no viruses found. If anyone had such a problem before or has an idea what might have caused it, please help. ED: @Michael Todd: ...try installing on another PC... I've installed it on my friends PC. He has the same OS version, with the latest updates just like mine (he wasn't too happy, even after I've assured him that it is easy to fix by uninstalling that driver :] ). It worked fine - no bluescreens or whatsoever. So I think I've narrowed it down to either BIOS settings, or some wicked driver conflict. Next thing I'm going to try is to re-install XP, or install windows 7. I'm not too happy with a prospect of mucking about with BIOS settings...

    Read the article

  • error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)

    - by ArunS
    We have online shopping site. When I am going to checkout page i am getting a error like this "error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)" From the apache error log i can see some attempts to connect to api.paypal.com. Here is the part of my apache error log * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.123... * connected * Connected to api.paypal.com (66.211.168.123) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 When i tried to connect to api.paypal.com using curl i am getting a error like this curl -iv https://api.paypal.com/ * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.91... connected * Connected to api.paypal.com (66.211.168.91) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Request CERT (13): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS alert, Server hello (2): * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 curl: (35) error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure Can anyone help me to figure out this. Thanks in Advance. Arun S

    Read the article

  • Massive SQL issue shutting down our site.

    - by Pselus
    Our website has started timing out like crazy today. All of our clients are finding it unusable. The only error we can seem to trace down as a potential problem is this: SQLAllocHandle on SQL_HANDLE_DBC failed Error ASP Description Error Category Microsoft OLE DB Provider for ODBC Drivers I have no idea what it means or how to go about fixing it. Anyone ever encountered this error before? Currently, you can log in to our site, but then once you go to do anything else, you find yourself logged out or nothing happens. We have a lot of Ajax going on so the "nothing happens" probably has to do with the Ajax pages not loading properly due to logouts and so nothing displays to the user. Like I said, I'm at a loss. Anyone have any advice on this error? EDIT I realize that this isn't necessarily a programming question, but we are a small startup company that just yesterday started talking about how we need to get a backup server running. Apparently we talked about it too late. We don't have a DBA, just 2 mid level programmers trying their hardest to keep our clients happy. So please, if you have any assistance give it but please don't close my question right now. EDIT 2 Turns out we had something on our server running called "ServerMask" that makes our IIS server look like Apache to the outside world. Shutting it down fixed our issue. Still no idea why it was messing up but it was the problem apparently. Thanks to everyone who tried to help.

    Read the article

  • ASA Slow IPSec Performance with Inconsistent Window Size

    - by Brent
    I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

    Read the article

  • Windows Virtual Machines will not run

    - by jlego
    I'm trying to setup a few virtual machines to use for testing websites in the various old versions of IE. I had Microsoft Virtual PC working on an older machine using XP mode and 2 other VHD's from Microsoft that allowed me to test in IE6-IE8. I've recently gotten a new work machine and am trying to set up the VMs again for testing, however nothing seems to be working. Both the old and the new system run Windows 7 64-bit Ultimate with AMD processors. I downloaded Virtual PC & XP mode from here http://www.microsoft.com/windows/virtual-pc/download.aspx and go through the installation process. XP mode is installed, but when I try to run it it goes through the initial setup process only to fail when it is almost complete with the error "Cannot Complete Setup". (After googling I see that this might be a conflict with my processor) I download other VHD's from here http://www.microsoft.com/windows/virtual-pc/download.aspx in order to get the other versions of IE and try to set those up in Virtual PC as well. I click on them to start the machine and both Windows 7 with IE8 and Windows Vista with IE7 just hang at a black screen. I try to use Virtual Box instead, and I get Windows XP with IE6 running, but I have no internet connection in the VM. I try all different settings and try to google the correct settings but nothing seems to work. When I load the VM, XP shows that its found new hardware but it needs the drivers. One of these pieces of hardware is the network adapter, but I can't connect to the internet to download the driver in the guest OS. VirtualBox tells me I need to install extensions in order for things to function properly. I go through the installation process in the guest OS and restart the VM, however now XP is asking for validation and I can't access the VM. I try installing the other 2 OS (Vista & 7) but I get a BSOD right after the startup screen appears and the VM restarts itself. I'm getting so frustrated trying to make this work, I would really appreciate any assistance on getting the VMs up and running or any alternatives for testing websites in Internet Explorer.

    Read the article

  • BackupPC - why does it use rsync --sender --server ... ?

    - by Jakobud
    I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Apache is spawning more and more processes!!

    - by erotsppa
    We have a LAMP setup that is working prety good for half a year. All of a sudden today the apache server (mysql servers are not on this box) started to die. It seems to have started to spawn more and more processes over time. Eventually it will consume all the memory and the server would just die. We are using prefork. In the mean time what we are doing is just added more ram and increased the MaxClients and ServerLimit parameter to 512. We're just prolonging the crash. The number still goes up slowly. Maybe in a day, it would reach that limit. What is going on? We only have around 15-20 request per second. We have 1Gb memory and it's not half used, there's no swapping going on. Why is apache creating more and more processes? It's almost like theres a leak somewhere! The database boxes are fine, they are not causing a delay to requests. We tested some queries everything is quick!

    Read the article

< Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >