Search Results

Search found 11316 results on 453 pages for 'ip geolocation'.

Page 293/453 | < Previous Page | 289 290 291 292 293 294 295 296 297 298 299 300  | Next Page >

• Unable to access VLAN host from VLAN interface in CentOS

  - by Amrit

  I am playing with VLAN (Virtual LAN) configuration on CentOS 6.4. I have 2 interfaces, eth0 and eth1. I have configured 2 VLAN interfaces eth0.20 and eth0.30 as #file: ifcfg-eth0.20 #------------- VLAN=yes DEVICE=eth0.20 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.20.1 GATEWAY=192.168.20.1 NETMASK=255.255.255.0 USERCTL=no #file: ifcfg-eth0.30 #------------- VLAN=yes DEVICE=eth0.30 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.30.1 GATEWAY=192.168.30.1 NETMASK=255.255.255.0 USERCTL=no Then connected a desktop to interface eth0 port using LAN cable and assigned 192.168.30.2/24 IP. When I try to ping 192.168.30.1 from 192.168.30.2 machine, It shows destination host unreachable. I am also not able to ping 192.168.130.2 from 192.168.30.1. However ping -I eth0 192.168.30.2 works fine. Any pointers?

  Read the article

• hosts file ignored, how to troubleshoot?

  - by Superbest

  The hosts file on Windows computers is used to bind certain name strings to specific IP addresses to override other name resolution methods. Often, one decides to change the hosts file, and discovers that the changes refuse to take effect, or that even old entries of the hosts file are ignored thereafter. A number of "gotcha" mistakes can cause this, and it can be frustrating to figure out which one. When faced with the problem of Windows ignoring a hosts file, what is a comprehensive troubleshoot protocol that may be followed? This question has duplicates on SO, such as hosts file seems to be ignored, HOSTS file being ignored, /etc/hosts file being ignored as well as numerous discussions elsewhere. However, these tend to deal with a specific case, and once whatever mistake the OP made is found out, the discussion is over. If you don't happen to have made the same error, such a discussion isn't very useful. So I thought it would be more helpful to have a general protocol for resolving all hosts-related issues that would cover all cases.

  Read the article

• Yahoo flagging mail as spam when using relay server

  - by modulaaron

  I'm using Postfix to relay mail from my site to my mail server. Mail is received properly at my Gmail and Hotmail accounts - only Yahoo is the problem. The Yahoo mail headers state: Received-SPF: none (mta1133.mail.mud.yahoo.com: domain of [email protected] does not designate permitted sender hosts) In contrast, the Gmail headers state: Received-SPF: pass (google.com: domain of [email protected] designates 74.50.xxx.xxx as permitted sender) client-ip=74.50.xxx.xxx; Reverse DNS is set up correctly, as is my SPF record and domainkeys/dkim (both domainkeys and dkim show pass(ok) in the Yahoo mail headers). Does anyone have any suggestions as to what I can do to solve the Yahoo problem (short of contacting Yahoo, as this is a brand new mail server)? Thanks

  Read the article

• Accessing apache on virtual pc

  - by Rick Hensly

  I am using a virtual pc to test my website. I can access all my webpages on the virtual pc. However, images don't load correctly. I can browse to my images folder and view all of them. However, if I click an image it will not load, and the apache log shows the virtual pc's ip trying to view the image: 192.168.0.55 - - [25/Jun/2009:20:10:41 -0400] "GET /images/pic.png HTTP/1.1" 302 220 Now, if I refresh the page it loads. 192.168.0.55 - - [25/Jun/2009:20:10:51 -0400] "GET /images/bg.png HTTP/1.1" 200 214 Also, images won't load in html or css. It seems like a redirecting problem or something, but I have no clue how to fix it. Thanks for any advice

  Read the article

• Unidentified Connection in Compaq CQ61Windows7 OS on DSL cable network connection

  - by Mohammed Thouseef

  I have Dell studio with shared DSL internet connection my router is "NETGEAR DG834" & Network connection discription is "Broadcom netlink tm gigabit ethernet" this connection is working fine with dell laptop with Vista homepremium OS. My Question is? If i connect HPcompaq presario CQ61 in this connection it will automatically select Public network and display unidentified connection i tried several times but not suceeded its OS is Win7 home premium. but wireless networking is working fine only this problem is faceing with DSL cable connection when i diagnos the connection an error will generate "Local Area Connection does not have a valid IP configuration" in LAN Connection status window i noticed IPV4 & IPV6 Connectivity is showing "No Network Access" please can you clarify whats the problem.

  Read the article

• Where Debian Lenny stores initial ifconfig values?

  - by Kuroki Kaze

  With upgrade of VMWare Player I suddenly found my Debian Lenny VM not getting IP address. Some DHCP issue maybe, I don't know. So I have to set it manually every boot in Player window, via: ifconfig eth0 down ifconfig eth0 192.168.175.128 netmask 255.255.255.0 up I usually start up VM and then connect to it via SSH, so this procedure bothers me. Sure I can add it to startup script, but is there some special place to enter these values? Like, some config file or so?

  Read the article

• Automatic subdomain wildcard for DHCP-DDNS additions?

  - by Igor Clark

  I'm running dhcp-4.0.2 server and bind-9.6.1-P3. When a new Mac OSX DHCP client with the name "harry" connects to the network, the DHCP server gives it a lease, and adds appropriate A & PTR records via DDNS. This works fine; harry.my.domain points to (e.g.) 192.168.1.3, the Mac client knows that its name is harry.my.domain, 192.168.1.3 points back to harry.my.domain, and all that is great. Now I want *.harry.my.domain to resolve to 192.168.1.3, and I don't want to have to go in and add wildcard records into zone files. I want the Mac to connect to the network, and have the hostname and wildcard subdomain resolve to the IP address it's been given. Is there a way to do this? Thanks!

  Read the article

• dns service on OS X Snow Leopard Server

  - by Sorin Buturugeanu

  Hello all, I have a Mac Mini (1.83GHz, 1.5 RAM) with a fresh install of OS X Snow Leopard Server and I want to use it for DNS and web hosting. What I have done so far is to go to the domain registrar and configure a new nameserver (ns.domain.tld) to point to my static IP. This Mac Mini is behind a DI-524 router and I have forwarded ports 53 and 80 to the Mini. I have also added the domain name to the DNS configuration pannel (as in the attachment), but intodns.com gives the following error (among others, and obviously the site is not working): "Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records." I don't know where to go from here .. Thank you to anyone willing to take the time to give me a hint!! seems that I can't post images but here's the link: http://i.imgur.com/zWI7Y.png

  Read the article

• Assistance in setting up new APC Smart-UPS RT on a new VMware enviroment

  - by user38085

  I'm new to the realm of setting up a APC Smart-UPS RT 8000VA UPS with a management network card (AP9618). The project calls for the upgrade of the firmware for the network card to the newest and greatest. It also calls for the Powerchute Business Software to be installed with notifications setup per email for temperature, shutdown, and battery low. I know I'll have to use the serial cable to flash the firmware and install the software on one server 2003 box. Also on that server I'll have to install the software and setup the GUI (IP address) interface. Whats confusing the most is the whole process, and steps to use without taking down the network, which would be very bad. In flashing the firmware does it take down the UPS? Do i have to run BOOTP commands to setup the network card? Also no agents will be used on any of the VWware OS's and no SNMP trap will be used.

  Read the article

• Connecting to a remote server through OpenVPN when local network subnet conflicts with remote network's subnet

  - by John Russell

  After connecting to a remote location via OpenVPN, I am trying to access a server on a network that exists on a subnet such as 10.0.1.0/24. However, the network I am trying to access this remote server from is on the same subnet: 10.0.1.0/24. I am unable to connect to my remote server via typing in its IP because of this conflict. I am unable to even access the public internet while connected to the VPN. Does anyone know how to mitigate this issue? I have access to the OpenVPN Access Server.

  Read the article

• Setting up dynamic DNS for linked router

  - by cherrun

  I have a 'main' router that receives the internet signal from the ISP and another one in my room, connected with a cable. The main router is running its original firmware and is very limited in its features, unfortunately I can not change this router, since my phone company has some hardcoded stuff in there and the internet will only work with this router. My second router is running DD-WRT firmware. Now I need to set up dynamic DNS, so I can access my NAS machine remotely, which is connected to the second router. As mentioned, this can't be done with the main router, due to its limited features. DHCP is turned off on the second router, since it gets its IP from the main one. Is there a possibility to set up dynamic DNS on the second router, without changing any (or much) on the main router? Maybe as a side note: I live in Germany, don't know if the set up of the routers are different in other countries.

  Read the article

• Setting up dynamic DNS for linked router

  - by cherrun

  I have a 'main' router that receives the internet signal from the ISP and another one in my room, connected with a cable. The main router is running its original firmware and is very limited in its features, unfortunately I can not change this router, since my phone company has some hardcoded stuff in there and the internet will only work with this router. My second router is running DD-WRT firmware. Now I need to set up dynamic DNS, so I can access my NAS machine remotely, which is connected to the second router. As mentioned, this can't be done with the main router, due to its limited features. DHCP is turned off on the second router, since it gets its IP from the main one. Is there a possibility to set up dynamic DNS on the second router, without changing any (or much) on the main router? Maybe as a side note: I live in Germany, don't know if the set up of the routers are different in other countries.

  Read the article

• What are industry standards and professional best practices in network hosts naming? [closed]

  - by Ivan

  Possible Duplicate: Naming convention for computers It seems an important and difficult dilemma for me how to name network hosts (routers, servers (while a server can be a router and host diverse services at the same time), virtual machines (while they host important services and can migrate), workstations and notebooks (using pc-username is not the best idea as users may change), printers & MFUs, surveillance IP cameras, etc). Are there known and accepted best practices for this task? Excuse me if there already was a similar question here (I think it probably was), I haven't found it.

  Read the article

• DD-WRT VPN error 800?

  - by MrZombie

  I have set up a router with DD-WRT Mega on my Asus WL-500gP V2, and I can't connect to the VPN service. I have set it up according to the configuration on the DD-WRT wiki, so the server IP is set to 192.168.1.1, which is the address of the router, and I set up the client addresses to be 192.168.1.20-29. My chap secrets are set up correctly, and still, I get an error 800 on windows XP. As far as I can tell, it means my network is unreachable. The server responds to ping.

  Read the article

• How to configure wpa_supplicant on RHEL6?

  - by Yang Jy

  I am running a version of RHCE6 on my laptop. I uninstalled the default NetworkManager in order that I could configure the network all in the command line. The Ethernet part is okay, but I have problem bringing up the wireless interface. What I got is: Bringing up interface wlan0: Determining IP information for wlan0... failed; no link present. Check cable? I did exactly what this article says. I am not sure if it is because the article is obsolete or something else. Please help.

  Read the article

• Red 5, First setup "ssl_error_rx_record_too_long" error message

  - by charles horvath

  I am using Windows 7 and I installed Red 5 0.9.1 just recently. After it installed I put 127.0.0.1 as the IP adress and 5080 as http port. After I start the service in windows I try to connect to the localhost in firefox (http://localhost:5080) and get this error An error occurred during a connection to localhost:5080. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) I checked my global flash settings and allowed localhost to pass along with the Red 5 folder in C/programfiles/red5. I currently have the up to date versions of JDK and JRE also. Any tips on what might be wrong?

  Read the article

• Can't ping host from vmware guest using bridged networking

  - by user199421

  Host is Windows 7 Guest is Ubuntu 11.04 Network adapter is wireless I can ping other computers on the network but not the host. No firewall are involved. Sniffing the traffic with wireshark it looks like both the host and the guest are using the same MAC address. My guest simply doesn't receive a reply when asking for 192.168.1.101 (the host) My router has no problem giving both of them different IP addresses but maybe duplicate MAC address is the problem? It seems logical that both will have the same MAC address (from the host point of view) but it strange that there is no work around for this because otherwise I don't see how the host and guess are supposed to communicate.

  Read the article

• Issues configuring CUPS print server for Ubuntu Server 9.10

  - by Tone

  I have a 9.10 Ubuntu Server installed and I want to make it a print server and am trying to get access to the cups browser admin page from a windows client machine. I installed cups: sudo apt-get install cups then I edited the /etc/cups/cupsd.conf file and tried several different listen cominbations: Listen 192.168.1.109:631 #ip my router gives it3 Listen /var/run/cups/cups.sock #already in conf file Listen fileserver:631 #hostname of server Port 631 #listen for all incoming requests on 631? samba is also installed (which I think is necessary to share the printer out? and finally I added my user to the lpadmin group: sudo adduser tone lpadmin but when I try to navigate any of the following I get 403 forbidden http://fileserver:631/admin http://fileserver:631 http://192.168.1.109:631/admin http://192.168.1.109:631 What did I miss?

  Read the article

• Device Manager in read-only remote mode when local

  - by Luke Puplett

  Hello - since configuring a Windows Web Server 2008 R2 x64 to be hardened for an internet-facing deployment I receive this: "Device Manager is running in read-only mode because you are running it on a remote computer." when entering Device Manager. I have tried reversing the changes I have made, such as: Re-adding Client for Microsoft Networks Re-enabling NetBIOS over TCP-IP Re-adding File and Printer Sharing Disabling the Windows Firewall in all profiles (public, domain, private) I get no joy. It looks like a Microsoft ballsup. I'll try and use Process Monitor to have a look. Google returns only 1 page for this error. Luke

  Read the article

• Set up nameserver with multiple domains

  - by Saif Bechan

  Hello, i have a dedicated with a primary ip and domain name. I added nameserver settings for this domain, and mx records. n1.mydomain.com ns2.mydomain.com etc. Now i want to add more domain with websites to my server. Now what is the best way to do this. Should i add the domain, and use the mydomain.com nameserver settings. Shoudl i add the domain and create his own nameserver. I should add the websites have to be optimized for best performance, fastest load time. Thank you for your time

  Read the article

• opening socket to google hangs on SYN_SENT

  - by puchu

  I have 2 computers now: downloader (asus at4nm10t-i) with debian and desktop (asus sabertooth 990fx) with gentoo in the same network under NAT even with the same ethernet card: RTL8111E. driver r8169 is compiled as module on both computers. Sometimes in evenings desktop cannot connect to google and all its services like now: curl -v http://www.google.by on downloader it received server's answer immediately. on desktop it hanged and when I ran in other terminal: netstat -ntp | grep curl >>tcp 0 1 192.168.0.7:54126 173.194.35.191:80 SYN_SENT 4876/curl after 1-2 minutes it received server's answer. I was tried to change ip of network, mac address of desktop but nothing changed. When I was trying to connect to another services except google: curl -v http://www.yahoo.com both computers received answers immediately! Only when I rebooted desktop it begins to work with google services correctly I cant understand what is this bug related to. In which bugtracker should I post this: r8169 or linux kernel or google? PS. Desktop was checked with memtest: 5 passes - no errors

  Read the article

• How to log the actual output in apache?

  - by Oscar Rodriguez

  I am doing LAMP development for a mobile platform. However, the client browser does not allow me to view the source code of visited pages. I consider the source code to be of huge importance for debugging, so I would like to configure my web server so every time a user makes a request, in addition to sending the client a response, that response (the actual contents of the returned page) is also stored in a file with a filename I can cross-relate with access_log (maybe ip-timestamp-filename? or maybe a unique ID in an additional column in access_log?). I've searched quite a bit, but haven't even gotten close to finding what I'm looking for. Has anybody been able to do this?

  Read the article

• VPN for a small organization

  - by user24091

  I am in charge of a small office network that has < 10 users. I want to be able to offer them access to the network from their home internet connections. At the moment we have a regular ADSL-router-firewall to provide local network access and a fixed IP address. I know there are enterprise-level VPN solutions, but these obviously won't be available to us because of the cost and complexity. What small-scale solutions are around that you could recommend, what would we need to deploy on the client side, and what would the clients need to do to access the VPN? Simplicity and low cost need to be the keys here. Thanks

  Read the article

• Adding Facebook IPv6 to Centos, getting CurlException 7

  - by Nick

  I'm correctly get following error. After searching about this issue, correct me if i'm wrong, I believe that adding/configuring IPv6 should solve the problem. PHP Fatal error: Uncaught CurlException: 7: Failed to connect to 2a03:2880:10:8f02:face:b00c:0:26: Network is unreachable\n thrown in /var/www/vhosts/facedex.net/httpdocs/fb/apps/seemyfuture/src/base_facebook.php on line 886 The problem is I dont know the right way to add it. There seems to have may methods. http://tldp.org/HOWTO/Linux+IPv6-HOWTO/x1035.html#AEN1044 http://unix.stackexchange.com/questions/34093/static-ipv4-ipv6-configuration-on-centos-6-2 My netstat show this. Shell doesnt recogize -rn6 though.It shows invalid option -- 6 netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 27.254.38.128 0.0.0.0 255.255.255.128 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 27.254.38.254 0.0.0.0 UG 0 0 0 eth0 FYI: I'm using Centos 5.7. Thank you a lot in advance.

  Read the article

• Windows SBS 2008 - how to diagnose port forwarding problems?

  - by Alt_Doru

  We have a Windows SBS 2008 machine. Several ports need to be forwarded from the router to the server (the machine hosts a FTP server, a Web server, and we need to be access it through Remote Desktop). We recently changed routers (from SpeedTouch to Huawei EchoLife HG520s). With the previous router, port forwarding worked fine. Now, after setting up port forwarding on the new router, nothing works anymore. Can anybody help me with directions on how to diagnose/troubleshoot port forwarding problems on the router and in Windows SBS 2008? E.G.: after forwarding a port in the router interface to the internal IP of the server, how can I see in the SBS 2008 logs if the request is properly forwarded to it?

  Read the article

< Previous Page | 289 290 291 292 293 294 295 296 297 298 299 300  | Next Page >