Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 297/455 | < Previous Page | 293 294 295 296 297 298 299 300 301 302 303 304  | Next Page >

• How to Configure IIS 7.5 to Host Several Classic ASP Sites using 1 IP Address?

  - by SidC

  We are running Windows Server 2008 R2 with IIS 7.5 and have 4-5 Classic ASP sites to install. The main site is stored in wwwroot and the other sites are stored in folders below wwwroot. We have 1 IP address for the server. How do I configure IIS to allow folks to browse/test the sites before domain names are pointed to te server? When I setup one of the sites in a subfolder of wwwroot and assign a separate port to it, I receive a message stating: Config Error Cannot add duplicate collection entry of type 'add' with unique key attribute 'value' set to 'index.asp' How do I remedy this error and permit IIS to render the site?

  Read the article

• Electricity in VAIO laptop ports while plugged in

  - by SRbH

  I have VAIO E series (SVE) laptop. While charger plugged in, touching VGA/HDMI/USB port metal casing gives me burning sensation. So, i checked it with voltmeter and i found that while plugged in there is presences of DC +1.0 V. Same case with my friend's VAIO E Series (VPCEH). Service center says this is normal. But i do not believe them as it is not the case with Dell Inspiron. Please let me know if you are facing same problem with VAIO and is it hazardous to devices which i connect to these ports (like HDD, LED, etc)?

  Read the article

• Smoothwall Express interface issues

  - by Timbermar

  I have a SmoothWall Express box that is currently configured with a Green and Purple interface. Both interfaces are in the same /24 subnet (which seems odd to me). The green interface (address of .254) has a DHCP server that is pushing addresses from .1 to .100 and the purple interface (.253) is pushing addresses from .101 to .120. Every machine here is trusted, and as such is connected to the green interface via a wired connection or wireless APs. Nothing is connected at all (port is physically empty, traffic graphs show no activity) to the purple interface. However, every machine here is pulling addresses from the purple interface. So the question boils down to, how do I remove/stop my machines from pulling from the purple dhcp interface? Also, shouldn't the purple interface (if we were using it for guest Wifi or something) be on a different subnet (i.e. 192.168.100.0/24 instead of 192.168.1.0/24 with all the trusted machines)?

  Read the article

• Strange failure audit in 2003 R2 X64 SP2

  - by Az

  our server is running 2003 R2 X64 SP2, we keep seeing this in clusters of around 4 rapid fire. Sometimes 2 hours, sometimes around 8 hours apart with slight variations. I am also seeing the same blank username and domain in an account locked out message, I have tried disabling all scheduled tasks, if anyone has any idea please let me know! I find these processes running out of svc host: AeLookupSvc, AppMgmt, BITS, Browser, CryptSvc, dmserver, EventSystem, helpsvc, IAS, lanmanserver, lanmanworkstation, Netman, Nla, RasMan, Schedule, seclogon, SENS, SharedAccess, ShellHWDetection, winmgmt, wuauserv, WZCSVC Logon Failure: Reason: Account currently disabled User Name: Domain: Logon Type: 3 Logon Process: Authz Authentication Package: Kerberos Workstation Name: PPCLUBES_TS Caller User Name: PPCLUBES_TS$ Caller Domain: PPCLUBES Caller Logon ID: (0x0,0x3E7) Caller Process ID: 928 Transited Services: - Source Network Address: - Source Port: -

  Read the article

• redirect on a Domino HTTP server?

  - by oidsman

  Simple question but:- We have a server running Domino Http server on port 80. We have another apache server running on 8081. We want to set a DNS entry (say 'Things') to point to a page on the 8081 server. As I see it we need to do some kind of redirect on the Domino server to say that any traffic from hostname 'Things' gets a redirect to "http://server:8081/content/". So, in summary, if I type in "http://Things" on my browser I get redirected to "http://server:8081/content/" Does anyone know how to do this on the Domino Http server? Thanks in advance for your help!

  Read the article

• Visual SVN server Running but cannot access / browse repositories

  - by user1783560

  Operating System: Windows Web Server 2008 R2 Visual SVN Version: 2.5.7 Subversion: 1.7.7 Apache: 2.2.22 I freshly installed the Visual SVN latest version on the server and created one repository in it. In the server management window, it shows that the server is up and running but when I try to browse it in a web browser, it doesn't respond. I am not able to import my existing code into the repository: Error: Cannot connect to server open/browse the repository with either command localhost:81/svn OR http://www.myserver.com:81/svn OR http:// myIPAddress:81/svn Visual SVN log is clean. The last information in the server log is that "The server is listening to port 81.

  Read the article

• Windows Server 2012 Essentials - Trying to setup "Anywhere Access" but the "Computer Access" list for users is blank

  - by tetranz

  I have a new installation of Windows Server 2012 Essentials and I'm trying to setup "Anywhere Access" for both VPN and remote desktop. The basic setup is all working. Shared folders is working but remote desktop has no computers available. On the server, if I edit a user with the Essentials Dashboard and go to "Computer access", the list is empty. The desktop computers have been joined to the domain. I can see them in AD under "Computers". I think our mistake was that we didn't use the connector tool to join the domain. We moved from a previous domain and went to Computer / Properties, changed the domain and started with a new profile. Is there something I can do now to make these desktops available for remote desktop? I can access a desktop directly no problem by going directly to it with the RDP client on port 3389. I do that from the outside world through an SSH tunnel.

  Read the article

• PostgreSQL won't start anymore

  - by Sander Declerck

  Today, my PostgreSQL doesn't start anymore on my windows machine... I've tried to start the service in windows services and got the following error: Windows could not start the PostgreSQL Database Server 8.3 service on Local Computer. Error 1053: The service did not respond to the start or control request in a timely fashion. Then I went to the command line to manually start C:/Program Files (x86)/PostgreSQL/8.3/bin/psql.exe, and then I got this error: psql: Could not connect to server: Connection refused (0x0000274D/10061) Is the server running on host "???" and accepting TCP/IP connections on port 5432? Edit: I found this in the logs: 2011-04-22 13:13:16 CEST LOG: could not receive data from client: No connection could be made because the target machine actively refused it. 2011-04-22 13:13:16 CEST LOG: unexpected EOF on client connection

  Read the article

• Unknown protocol when trying to connect to remote host with stunnel

  - by RaYell

  I'm trying to set up a stunnel for WebDav on Windows. I want to connect 80 port on my local interface to 443 on another machine in my network. I can ping the machine remote machine. However when I use the tunnel, I'm getting this error all the time SSL state (accept): before/accept initialization SSL_accept: 140760FC: error:140760FC:SSL routines:SSL23_GET_CLIENT_HELLO:unknown protocol There is nothing in the logs on the other machine and here's my stunnel connection config [https] accept = 127.0.0.2:80 connect = 10.0.0.60:443 verify = 0 I've set it up to accept all certificates so this shouldn't be a problem with a self-signed certificate remote host uses. Does anyone knows what might be the problem that this connection cannot be eastablished?

  Read the article

• Xerox Workcentre 3119 and Linux

  - by Milan Babuškov

  I'm trying to get Xerox Workcentre 3119 printer to work on Linux. It's a multifunction device (printer and scanner). I run the CUPS web interface at: http://localhost:631/ and it recognizes it on USB port and even suggests Gutenprint driver from the list. When I try to print a test page, the printer goes through "warming up" process (i.e. lights blink and sound is heard) but does not print anything. There are no errors in /var/log/cups/error_log and access_log shows as if everything is ok. The printer works fine in Windows XP. Does anyone have any experience with this printer on Linux?

  Read the article

• 3CX behind UT7.1 using a callcentric.com SIP account

  - by Corey

  Has anyone had any luck with getting 3CX working behind UT7.1 with a SIP account from callcentric.com? I am willing to reset my current UT box back to defaults, and start from there. I have a static public IP assigned to the external interface. My internal addressing is 192.168.76.0 . My 3CX box has 192.168.76.17 . Would anyone be willing to give me a step by step of changes to make in UT / 3CX. I currently have my UT box unplugged, and have replaced it with a Linksys unit. I have port forwarding setup for… TCP/UDP 5060 to 192.168.76.17 UDP 9000-9049 to 192.168.76.17 … and everything works great. I also have additional external IPs available if that helps.

  Read the article

• Dell powerconnect 6224 vlan routing

  - by user1007727

  I have a small network and I need help with routing .. . My VLANs VLAN 1010 SALES VLAN 1020 HR I have assigned the above vlans to a tagged port and I have added a default route to send the traffic of to my firewall. ip route 0.0.0.0 0.0.0.0 10.10.10.10 I have added a new vlan VLAN 1030 Services and I would like its traffic to go to a different interface on the firewall, 10.10.10.20 how can I go about doing that? can someone give me an example? your help is highly appreciated. Thank you

  Read the article

• How can I start using MS-SQL Server ( express )

  - by Oscar Reyes

  Hello. I have just installed Microsoft SQL Express from here: http://www.microsoft.com/Sqlserver/2005/en/us/express-down.aspx I need it because an example of some code I have uses it. My question is: How do I start using it? Which port it opens by default. All I have after installing it is this: I'm not asking for a full tutorial on how to admin MSSql, just a hint on what to do next. I have downloaded and tested in the past Oracle XE and test it with SQuirreL SQL client with out problems.

  Read the article

• HP Server bios boot delay

  - by jjrab

  I'm just going to throw this out there in case anyone else has run accross this... I have an HP DL320 G5p that had the motherboard replaced due to a faulty NIC port. After several calls to HP, two motherboard replacements, PCI riser card replacements, Processor replacement, and power supply replacement, the server takes approx. 10 minutes before it boots into the BIOS. It then boots up with no issues. We've run the HP smart start cd and performed the system tests and everything passed. All firmware has also been upgraded to the latest as well. Has anyone else seen this and found a fix? I am still working with HP, but there seems to be a struggle on their part to figure this out, so I'm curious to know if anyone else has experienced this and found a fix - thanks...

  Read the article

• List of tablets with keyboards.

  - by JamesM

  Please if you know any good tablets with keyboards that come either built-in or attachable (not via a USB port) please post a link to the tablet, Please add a review for that tablet if you have one, if you don't have one please say what you would do with it if you had one. It must have a physical keyboard, Cannot be a wired or wireless keyboard, only built-in/attachable see below tablets for more of an idea. Tablets With Keyboards: http://gdgt.com/asus/eee/pad/slider/ http://gdgt.com/asus/eee/pad/transformer/ If you have a table, Please what do you think of it: (Review) Your-Name: Your review. If you don't have a tablet (with a non USB keyboard) please say what you would do with one: JamesM: If I have a slider or a transformer, it would be running kFreeBSD-Debian-Squeeze. Please feel free to improve the layout/format of this topic.

  Read the article

• Vlan and Switch setting - dummy

  - by Andras Sebestyen

  I need to speak tomorrow the network engineer and I would like to understand his so apologise for the Dummy question: In the school we have a cab with a 24 port Netgear manageable switch with an admin and curriculum VLAN settings. Usually, as I over heard, in the morning and around 4.30pm there are a slowdown period on the computers which connect to this switch. No one could track this back yet. Questions: What is the best way to track back this slowdown Would it be a temporary solution to physical separate the two network with 2 switches If that would work how can I link them together to be able to see the curriculum from the admin side. Do I need an extra router then? Too many questions but I have no clue where to start and the gentleman will be paid by hours... can you see where I am coming from?:) Could you guide me in the right direction please? Any comment would be appreciated and please send links if you down vote the question:)

  Read the article

• Creating an office network and monitoring all activity without a proxy

  - by Robert

  We are setting up our office network and would like to track all the websites visited by our employees. However, we would not like to use any proxy based solutions. Our work is highly dependent on applications in which you cannot configure a proxy. Hence, the approach we would like to follow is setting up a router inside a computer (something like this : http://www.techrepublic.com/article/configure-windows-server-2003-to-act-as-a-router/5844624) This will also allow us to attach multiple ethernet cards and have redundancy in internet connectivity with complete abstraction from the user about which connection is being used. But most importantly, since all the traffic will be going through the computer (configured as a router) I assume there will be a way to run packet analysis on all the request / responses being made. For example, list all the FTP servers connected to (port 21), give a graph of all the URLs visited per day by frequency. Is there already a software which does this ? Or is it possible to build something like this ?

  Read the article

• Strange email coming from/to my computer

  - by Micah

  I'm running smtp4dev on my machine to trap anything going in/out of my computer on port 25 for testing purposes. Every so often this email gets trapped and I have no idea what it's from. I have Microsoft Security Essentials running on my machine and it hasn't identified and viruses or anything so I'm not sure what's going on. Here's the content of the message: Received: from [125.180.72.4] by 173.162.7.130 SMTP id O2Ncv62Ghig1vR for <[email protected]>; Fri, 24 Jun 2011 20:36:15 +0200 Received: from [125.180.72.4] by 173.162.7.130 SMTP id O2Ncv62Ghig1vR for <[email protected]>; Fri, 24 Jun 2011 20:36:15 +0200 Message-ID: <[email protected]> From: "" <[email protected]> To: <[email protected]> Subject: BC_173.162.7.130 Date: Fri, 24 Jun 11 20:36:15 GMT MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_000D_01C2CC60.49F4EC70"

  Read the article

• OpenVPN Bridge on pfsense: once LAN pings clients, connectivity breaks

  - by Lucas Kauffman

  So I'm using a pfsense openvpn to bridge my LAN segment so VPN users can access the servers. The problem I'm having now is that I can establish a connection, I can ping the LAN server from the VPN, but as soon as I ping the client from the LAN server, there is no connectivity anymore between both parties. So: connect from the VPN client to the LAN = works ping the LAN from the VPN client = works access server from the VPN (ssh, ftp,...) = works ping client from server = doesn't work ping LAN from the VPN client = doesn't work anymore My bridge has em1 and ovpns1 bridged. I noted with tcpdump that ICMP is reaching the bridge between LAN and the VPN segment. But it's not put onto the em1 interface for some reason. My pfsense is running on an ESXi host with th vSwitch port enabled in promiscious mode. Firewall rules allow in and outbound traffic regardless origin or destination.

  Read the article

• How can I fix my Virtual PC 2007 network configuration

  - by DanJ

  Hi, I have installed Windows Virtual PC 2007 on my Windows 2003 R2 Server. I have installed a virtual Windows XP. I have configured the virtual PC to use Shared Networking (NAT) I have disabled the firewall on the virtual windows XP The problem: I am unable to PING from Windows 2003 (the host) to the Windows XP (virtual) I do have normal traffic from the virtual to the internet Could this problem be related to routing? How I can I fix this network configuration to allow for the following traffic: 1. From Virtual to Internet 2. From Host to Virtual 3. If possible, from Internet to Virtual on pre-defined ports (port forwarding?) Thanks

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Can't connect using Jail SFTP account

  - by Fazal

  I've been following this tutorial "Limiting Access with SFTP Jails on Debian and Ubuntu" and whilst I've had no errors setting it up, I've had issues on Ubuntu 10.04LTS logging in as a user on a virtualhost. I've changed my SSH port to 22022, and enter all the credentials when attempting to login. I ran these commands to add a user to the virtualhost: # useradd -d /srv/www/[domain] [username] # passwd [username] # usermod -G filetransfer [username] # chown [username]:[username] /srv/www/[domain]/public_html I should add that this is the only time I've setup the user they have no other /home directories or such. The directory that does exist is at /srv/www/example.com/public_html When I try using a desktop package such as cyberduck to login to the site, I keep getting a "Login failed with this username or password". I am completely lost as what to do next... The reason why I'm trying this method is because I want my clients to use SFTP and not FTP to upload files to their websites. Any help or direction is appreciated.

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• Direct DB to Web Server connection

  - by Joel Coel

  I have a database server sitting right underneath a virtual machine host server in the rack, and this vm host is primarily responsible for servers hosting a couple different web sites and app servers that all talk to databases on the other server. Right now both servers are connected to the same switch, and I'm pretty happy with the pathing. However, both servers also have an unused network port. I wondering about the potential benefits of using a short crossover or normal+auto mdix network cable to connect these two servers together directly. Is this a good idea, or would I be doing something that won't show much benefit and is just likely to trip up a future admin who's not looking for this? The biggest weakness I can see right now is that this would likely require a code change for each vm app to point to the new IP of the database server on this private little network, and if I have a problem with the virtual machine host and have to spin up it's guests elsewhere while I fix it I'll have to change this back before things will work.

  Read the article

• Laptop recommendation for home user

  - by Mehper C. Palavuzlar

  I'm going to buy a new laptop soon and I need Super Users' recommendations. The following criteria are crucial for me: Intel i series processor Min. 4 GB RAM Min. 500 GB HDD HDMI port Min. 3 USB ports Not a monster, but a good graphics card Multimedia card reader DVD-RW Double Layer No heating problems! What do you recommend me? I'm considering buying a Vaio but I'm not sure. TIA.

  Read the article

< Previous Page | 293 294 295 296 297 298 299 300 301 302 303 304  | Next Page >