Search Results

Search found 11126 results on 446 pages for 'hardware requirements'.

Page 3/446 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Starting my own server - basic recommendations and questions [closed]

  - by Ilia Rostovtsev

  Possible Duplicate: Can you help me with my capacity planning? I'm planning to start my own high-performance server and then use collocation services for keeping it up and running. I'm planning to USE it for processing videos and keeping big video site up! (using FFMpeg, MENcoder and etc.) I just need recommendations on whether listed hardware is good enough and will work together well and fast enough. Do I need anything else (missed something). I remember about CPU coolers though! ;) I'm planning to use SSD drives so please tell me if it's going to work just as regular HDDs (but much faster)? Are they going to be used as RAID (is this possible for SSDs)? Here is what I would like to get: Intel ® Server System SR1600URHSR (Urbanna) or Intel® Server System SR1695WBAC 2 x Intel Xeon X5650 4 x 16Gb DDR-III 1333MHz Kingston ECC Reg (KVR13R9D4/16) 3 x (or maybe 4x) 480Gb SSD Intel 520 Series (SSDSC2CW480A3K5) Which server system would be better? Is listed hardware new/good enough and worth buying it at the moment? Should I probably take a look at something slightly more expensive but more up to date and powerful, may be? After all as software I would like to use CentOS 6 64 bit + WHM/CPanel? Any other suggestions on maybe cheaper and same/more powerful server management system but WHM? What most important points to keep in mind when starting/maintaining your own server?

  Read the article

• Ubuntu 10.04 LTS Minimal requirements (special)

  - by BDX

  I have a PC with 512MB of RAM, an Intel Pentium 4 processor(2GHz), SiS 651 video card(32MB) and a SiS C-Media AC'97 sound controller. I know that my video card is not and will not be supported for Linux. But I wonder if my PC is able to install and start Ubuntu, not just 10.04 LTS, because I'm willing to download 12.04 LTS when it's released. Will unity work? I searched on the internet but I couldn't find a good answer. Thanks in advanced.

  Read the article

• C#/XNA get hardware mouse position

  - by Sunder

  I'm using C# and trying to get hardware mouse position. First thing I tryed was simple XNA functionality that is simple to use Vector2 position = new Vector2(Mouse.GetState().X, Mouse.GetState().Y); After that i do the drawing of mouse as well, and comparing to windows hardware mouse, this new mouse with xna provided coordinates is "slacking off". By that i mean, that it is behind by few frames. For example if game is runing at 600 fps, of curse it will be responsive, but at 60 fps software mouse delay is no longer acceptable. Therefore I tried using what I thought was a hardware mouse, [DllImport("user32.dll")] [return: MarshalAs(UnmanagedType.Bool)] public static extern bool GetCursorPos(out POINT lpPoint); but the result was exactly the same. I also tried geting Windows form cursor, and that was a dead end as well - worked, but with the same delay. Messing around with xna functionality: GraphicsDeviceManager.SynchronizeWithVerticalRetrace = true/false Game.IsFixedTimeStep = true/fale did change the delay time for somewhat obvious reasons, but the bottom line is that regardless it still was behind default Windows mouse. I'v seen in some games, that they provide option for hardware acelerated mouse, and in others(I think) it is already by default. Can anyone give some lead on how to achieve that.

  Read the article

• Register Now! Oracle Hardware Sales Training: Hardware and Software - Engineered to be Sold Together!

  - by swalker

  Dear partner, You can now register for Oracle’s EMEA Hardware Sales Training Roadshow: "Hardware and Software - Engineered to be Sold Together!" The objective of this one-day, face-to-face, free of charge training session is to share with you and your Oracle peers the latest information on Oracle’s products and solutions and to ensure that you are fully equipped to position and sell Oracle’s integrated stack. Please find agenda, schedule, details and registration information here. The EMEA Hardware Sales Training Roadshow is intended for Oracle Partners and Oracle Sales working together. Limited seats are available on a first-come-first-serve basis, so kindly register as early as possible to reserve your seat. We hope you will take maximum advantage of these great learning and networking opportunities and look forward to welcoming you to your nearest event! Best regards, Giuseppe Facchetti Partner Business Development Manager, Servers, Oracle EMEA Sasan Moaveni Storage Partner Sales Manager Oracle EMEA

  Read the article

• How to install hardware drivers for my laptop

  - by John Flisk

  Everytime I change the OS I usually format my laptop. It is an HP tx-2 Touchsmart. It has a touchscreen and additional hardware that isn't working (i.e. volume control buttons and the network discovery) If I was on windows I would just download the hardware drivers from the HP website. How do I go about installing the software for the built-in hardware of my laptop? I am new to the community and I really want to get this computer working like it used to, to get the full Ubuntu experience. Please direct me, thank you.

  Read the article

• Requirement refinement between two levels of specification

  - by user107149

  I am currently working on the definition of the documentation architecture of a system, from customers needs to software/hardware requirements. I encounter a big problem with the level of refinement of requirements. The classic architecture is : PTS -- SSS -- SSDD -- SRS/HRS with PTS : Purshaser Technical Specification SSS : Supplier System Specification SSDD : System Segment Design Description SRS / HRS : Software / Hardware Requirement Specification. Requirements from PTS are reworked in SSS, this document only expressed the needs (no design requirements are defined at this level). Then, the system design is described in SSDD : we allocate requirements from the SSS to functions from the design and functions are then allocated to component (Software or hardware) (we are still at the SSDD level). Finally, for each component, we write one SRS or one HRS. Requirements in SRS or HRS are refinement of requirements from SSS (and traceability matrix are made between these two levels). My problem is the following one : Our system is a complex one, and some of the requirements in the SSS needs to be refined twice to be at the right level in the SRS (means that software people can understand the requirement to make their coding). But, with this document architecture, I can only refine once the requirements from the SSS. The second problem is that only a part of the requirements from the SSS needs to be refined twice. The other part only need one refinement. On the picture below, the green boxes are requirements at the right level for SRS or HRS. And purple boxes are intermediate requirements which can not be included in SSS since they are design requirements. Where can I put these purple requirements ?? Is there someone who has already encountered this problem ? Should I write two documents at SRS level ? Should I include intermediate requirements in SSDD ? Should I includes the two refinement levels (purple and green) in the same SRS document (not sure that's possible since a SRS is only for one component) ??? Thanks for your help and expertise ;-)

  Read the article

• GPL licensed software installed on commercial hardware

  - by Alexander Reshytko

  Do vendors need to provide sources, at the customer's request, for GPL licensed software installed on the hardware they sell? For example, a vendor sells an IPTV box and pre-installs some proprietary software product which is linked with some GPLed library. As a consequence, the software becomes GPLed itself. Does the vendor need to provide the source code for it? The vendor doesn't sell that software, he sells hardware.

  Read the article

• Firefox 12's hardware acceleration on Ubuntu 12.04 LTS

  - by user64943

  After I have installed Ubuntu 12.04 LTS (32 bits), Firefox 12 works fine but without hardware acceleration. Needless to say I have the latest nVidia's proprietary drivers installed and my Firefox Preferences, on "Advanced" tab, "Browsing" section, have the option "Use hardware acceleration when available" checked. I have tried the following things before asking this question: Creating a boolean key "webgl.force-enabled" and set it to true on Firefox's page about:config; Starting a new profile like commented on thread Mozilla Firefox 12 is very slow on Ubuntu 12.04 LTS; I have updated my nVidia driver to version 295.53. And none of this have worked. As you can see below in my Firefox's page about:support report, "Graphics" section shows no "GPU Accelerated Windows": Adapter Description NVIDIA Corporation -- GeForce GTX 460/PCIe/SSE2 Vendor ID NVIDIA Corporation Device ID GeForce GTX 460/PCIe/SSE2 Driver Version 4.2.0 NVIDIA 295.53 WebGL Renderer NVIDIA Corporation -- GeForce GTX 460/PCIe/SSE2 -- 4.2.0 NVIDIA 295.53 GPU Accelerated Windows 0 AzureBackend skia I use the following site to test hardware acceleration: http://ie.microsoft.com/testdrive/Performance/FishBowl/ On Windows 7 I get 60 fps even with 1,750 fishes on browser's Full Screen Mode (1680x1050x32bit-color). On Ubuntu 12.04 LTS, same nVidia drivers (as shown in report), won't go faster than 15 fps with only 1,000 fishes. Can anybody help me? Best Regards,

  Read the article

• How to Identify Which Hardware Component is Failing in Your Computer

  - by Chris Hoffman

  Concluding that your computer has a hardware problem is just the first step. If you’re dealing with a hardware issue and not a software issue, the next step is determining what hardware problem you’re actually dealing with. If you purchased a laptop or pre-built desktop PC and it’s still under warranty, you don’t need to care about this. Have the manufacturer fix the PC for you — figuring it out is their problem. If you’ve built your own PC or you want to fix a computer that’s out of warranty, this is something you’ll need to do on your own. Blue Screen 101: Search for the Error Message This may seem like obvious advice, but searching for information about a blue screen’s error message can help immensely. Most blue screens of death you’ll encounter on modern versions of Windows will likely be caused by hardware failures. The blue screen of death often displays information about the driver that crashed or the type of error it encountered. For example, let’s say you encounter a blue screen that identified “NV4_disp.dll” as the driver that caused the blue screen. A quick Google search will reveal that this is the driver for NVIDIA graphics cards, so you now have somewhere to start. It’s possible that your graphics card is failing if you encounter such an error message. Check Hard Drive SMART Status Hard drives have a built in S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. The idea is that the hard drive monitors itself and will notice if it starts to fail, providing you with some advance notice before the drive fails completely. This isn’t perfect, so your hard drive may fail even if SMART says everything is okay. If you see any sort of “SMART error” message, your hard drive is failing. You can use SMART analysis tools to view the SMART health status information your hard drives are reporting. Test Your RAM RAM failure can result in a variety of problems. If the computer writes data to RAM and the RAM returns different data because it’s malfunctioning, you may see application crashes, blue screens, and file system corruption. To test your memory and see if it’s working properly, use Windows’ built-in Memory Diagnostic tool. The Memory Diagnostic tool will write data to every sector of your RAM and read it back afterwards, ensuring that all your RAM is working properly. Check Heat Levels How hot is is inside your computer? Overheating can rsult in blue screens, crashes, and abrupt shut downs. Your computer may be overheating because you’re in a very hot location, it’s ventilated poorly, a fan has stopped inside your computer, or it’s full of dust. Your computer monitors its own internal temperatures and you can access this information. It’s generally available in your computer’s BIOS, but you can also view it with system information utilities such as SpeedFan or Speccy. Check your computer’s recommended temperature level and ensure it’s within the appropriate range. If your computer is overheating, you may see problems only when you’re doing something demanding, such as playing a game that stresses your CPU and graphics card. Be sure to keep an eye on how hot your computer gets when it performs these demanding tasks, not only when it’s idle. Stress Test Your CPU You can use a utility like Prime95 to stress test your CPU. Such a utility will fore your computer’s CPU to perform calculations without allowing it to rest, working it hard and generating heat. If your CPU is becoming too hot, you’ll start to see errors or system crashes. Overclockers use Prime95 to stress test their overclock settings — if Prime95 experiences errors, they throttle back on their overclocks to ensure the CPU runs cooler and more stable. It’s a good way to check if your CPU is stable under load. Stress Test Your Graphics Card Your graphics card can also be stress tested. For example, if your graphics driver crashes while playing games, the games themselves crash, or you see odd graphical corruption, you can run a graphics benchmark utility like 3DMark. The benchmark will stress your graphics card and, if it’s overheating or failing under load, you’ll see graphical problems, crashes, or blue screens while running the benchmark. If the benchmark seems to work fine but you have issues playing a certain game, it may just be a problem with that game. Swap it Out Not every hardware problem is easy to diagnose. If you have a bad motherboard or power supply, their problems may only manifest through occasional odd issues with other components. It’s hard to tell if these components are causing problems unless you replace them completely. Ultimately, the best way to determine whether a component is faulty is to swap it out. For example, if you think your graphics card may be causing your computer to blue screen, pull the graphics card out of your computer and swap in a new graphics card. If everything is working well, it’s likely that your previous graphics card was bad. This isn’t easy for people who don’t have boxes of components sitting around, but it’s the ideal way to troubleshoot. Troubleshooting is all about trial and error, and swapping components out allows you to pin down which component is actually causing the problem through a process of elimination. This isn’t a complete guide to everything that could likely go wrong and how to identify it — someone could write a full textbook on identifying failing components and still not cover everything. But the tips above should give you some places to start dealing with the more common problems. Image Credit: Justin Marty on Flickr     

  Read the article

• Mobile Development- Obtaining development hardware - best practices?

  - by Zoot

  I'm looking to get into smartphone development, but there a quite a few options out there for platforms right now. (iOS/Android/WebOS/Bada/Symbian/MeeGo/WindowsMobile/JavaME) I'd like to have development hardware to test my code and the overall functionality of the devices. What is the best way to obtain and/or borrow hardware for development and testing? Are there rules of thumb to follow which apply to all companies and platforms? In this situation, I'm a single developer. Does this process change for a startup? A hackerspace? A small business? A large business? Thanks.

  Read the article

• Mobile Development- Obtaining development hardware - best practices?

  - by Zoot

  I'm looking to get into smartphone development, but there a quite a few options out there for platforms right now. (iOS/Android/WebOS/Bada/Symbian/MeeGo/WindowsMobile/JavaME) I'd like to have development hardware to test my code and the overall functionality of the devices. What is the best way to obtain and/or borrow hardware for development and testing? Are there rules of thumb to follow which apply to all companies and platforms? In this situation, I'm a single developer. Does this process change for a startup? A hackerspace? A small business? A large business?

  Read the article

• Well supported Hardware Raid Controller

  - by ftiaronsem

  Hello alltogether I am currently planning to buy a hardware-raid controller. This became necessary since I am running Linux and Windows in parallel and now need the redundancy for both OS (Im am going to use RAID1 / Mirroring). Therefore I am searching for a hardware raid controller which is well supported by linux / ubuntu (reporting smart values, stats for the harddrives, etc...). This controller should have four sata ports and if possible it should fit in a PCIE-1x Slot. I would greatly appreciate, if you could suggest some devices. Thanks in advance

  Read the article

• Which iPhone/iPod Hardware to Support for iPhone Game

  - by ashes999

  I'm coming from a background of Android. I would like to figure out what kind of iBlah device hardware I need to support for iPhone game development. From my research, it seems that I need to support both iPod and iPhone. But which versions of hardware? is 3G still used? What about 3GS? For example, the -S phones seem to have dual core instead of single-core CPUs. I also worry about performance. In Android, I had a severely low-end phone, which meant pretty much anything that ran okay there ran okay on other phones. For iPhone, how do I figure out what to support in terms of performance?

  Read the article

• Ubuntu Touch Official Hardware? [duplicate]

  - by user1628

  This question already has an answer here: Where can I get a device with 'Ubuntu for phones' pre-installed? 1 answer I really like the look of Ubuntu touch and I want it ASAP, however, I am NOT willing to buy a device simply to port ubuntu touch on it. I don't want to void all warranties and take any risks. Therefore, I am really just waiting for official ubuntu touch hardware (devices made for ubuntu touch). I can't find any rumours or estimated release dates online, in fact, I can't find out anything at all. Can anyone? If so, what and where? When do you think they'll be official hardware? What price do you think it'll be? Do you think canonical/ubuntu will manufacture it themselves? Thanks, Zach

  Read the article

• Choppy video in vlc even with hardware acceleration on ATI Radeon HD

  - by l0b0

  After installing Catalyst 11.12 and studying instructions (1, 2) to enable hardware acceleration I ended up with the following command: sudo apt-get install xvba-va-driver libva-glx1 vainfo && \ vainfo && \ vlc --verbose 2 --ffmpeg-hw video.1080p.x264.mkv The output confirms that it's using the VA API: avcodec decoder: Using VA API version 0.32 for hardware decoding. But even after a reboot the video still looks choppy. There's no vlc output to indicate that the codec is having trouble, or that it's skipping frames. Any idea what could be the problem? Using vlc 1.1.12 with default settings. Also tried (in sequence): sudo apt-get install libva-glx1 sudo apt-get install --reinstall libgl1-mesa-glx:i386 libgl1-mesa-glx:amd64 libgl1-mesa-dri:i386 libgl1-mesa-dri:amd64 xserver-xorg-core Rebooting No luck yet. Specs from /proc/cpuinfo : Intel Core i7 CPU 950 @ 3.07GHz

  Read the article

• No 'Hardware' tab in audio and no profiles

  - by Gene

  If I run the 12.x ubuntu (latest May 2012) from the CD, I get full audio settings, and sound playing in speaker. Profiles let me change analog to digital in/out. Once I run install from the same CD onto the laptop HD, once it boots the first time, after selecting audio settings, there is no 'Hardware' tab and no way to change profiles. Worst part is the audio device is set to SPDIF so nothing comes out of the speakers. Very off how booting off the CD I can get analog audio, and installing to HD and booting seems to limit the profile to something useless. Laptop is a 5 year old Dell D820 with Nvidea 128meg video on a 1920x1200 screen and T7200 CPU. I suspect if I could get the damn HARDWARE tab back in audio settings, I could just select the proper Analog profile - just as is the case if running from a boot CD. Searched the web, no similar problems found... any help appreciated!

  Read the article

• Software/Hardware Development?

  - by SwarthyMantooth

  Sincere apologies if this is the wrong place to ask this. I am a computer engineering student and I'm currently on my first co-op of the required 5 I have to take, and I've noticed that all I'm really given is software engineering jobs. I love developing software, but I don't want to lose out on the hardware aspect of computers, as having a hybrid knowledge of the two is why I chose this major in the first place. So I guess my question is: Are there any software engineering jobs that still allow you to handle and interface with hardware on a very low level? Or am I to be forced to choose which focus I love more?

  Read the article

• Well supported Hardware Raid Controller

  - by ftiaronsem

  I am currently planning to buy a hardware-raid controller. This became necessary since I am running Linux and Windows in parallel and now need the redundancy for both OS (Im am going to use RAID1 / Mirroring). Therefore I am searching for a hardware raid controller which is well supported by linux / ubuntu (reporting smart values, stats for the harddrives, etc...). This controller should have four sata ports and if possible it should fit in a PCIE-1x Slot. I would greatly appreciate, if you could suggest some devices. Thanks in advance

  Read the article

• Good resources for learning about graphics hardware

  - by Ken

  I'm looking for some good learning resources for graphics hardware (and associated low level software). Basically I want to learn more about what goes on underneath the opengl/direcx API layers in terms of how things are implemented. I familiar with what happens in principle during the various stages of the rendering pipeline (viewing, projection, clipping, rasterization etc). My goal is to be able to make better and more informed decisions about tradeoffs and potential optimisations when graphics/shader programming with respect to the following kinds of issues; batching view culling occlusions draw order avoiding state changes triangles vs pointsprites texture sampling etc Basically whatever the graphics programmer needs to know about modern graphics hardware in order to become more effective. I'm not really looking for specific optimisation techniques, rather I need more general knowledge so that I will naturally write more efficient code.

  Read the article

• Generalize, or Fix The Problem?

  - by Droogans

  Which of these two programmers is "better", from a managerial standpoint? The first programmer is Albert. You tell Al to make a system that will pass you the salt at the dinner table. He does it in less than a day. It works fine. The second programmer is Ben. Ben is told to make a program to pass the salt, and after two days, he's still working on it. It will save time in the long run...if you need pepper, ketchup, etc. There isn't any clear indication that there will be a need for this, but it's not improbable. Who's the better programmer to have working under you, as a manager?

  Read the article

• Requesting quality analysis test cases up front of implementation/change

  - by arin

  Recently I have been assigned to work on a major requirement that falls between a change request and an improvement. The previous implementation was done (badly) by a senior developer that left the company and did so without leaving a trace of documentation. Here were my initial steps to approach this problem: Considering that the release date was fast approaching and there was no time for slip-ups, I initially asked if the requirement was a "must have". Since the requirement helped the product significantly in terms of usability, the answer was "If possible, yes". Knowing the wide-spread use and affects of this requirement, had it come to a point where the requirement could not be finished prior to release, I asked if it would be a viable option to thrash the current state and revert back to the state prior to the ex-senior implementation. The answer was "Most likely: no". Understanding that the requirement was coming from the higher management, and due to the complexity of it, I asked all usability test cases to be written prior to the implementation (by QA) and given to me, to aid me in the comprehension of this task. This was a big no-no for the folks at the management as they failed to understand this approach. Knowing that I had to insist on my request and the responsibility of this requirement, I insisted and have fallen out of favor with some of the folks, leaving me in a state of "baffledness". Basically, I was trying a test-driven approach to a high-risk, high-complexity and must-have requirement and trying to be safe rather than sorry. Is this approach wrong or have I approached it incorrectly? P.S.: The change request/improvement was cancelled and the implementation was reverted back to the prior state due to the complexity of the problem and lack of time. This only happened after a 2 hour long meeting with other seniors in order to convince the aforementioned folks.

  Read the article

• Developmnet process for an embedded project with significant Hardware change

  - by pierr

  Hi, I have a good idea about Agile development process but it seems it does not fit well with a embedded project with significant hardware change. I will describe below what we are currently doing (Ad-hoc way , no defined process yet). The change are divided to three categories and different process are used for them : complete hardware change example : use a different video codec IP a) Study the new IP b) RTL/FPGA simulation c) Implement the leagcy interface - go to b) d) Wait until hardware (tape out) is ready f) Test on the real Hardware hardware improvement example : enhance the image display quaulity by improving the underlie algorithm a)RTL/FPGA simulation b)Wait until hardware and test on the hardware Mino change exmaple : only change hardware register mapping a)Wait until hardware and test on the hardware The worry is it seems we don't have too much control and confidence about software maturity for the hardware change as the bring up schedule is always very tight and the customer desired a seemless change when updating to a new version hardware. How did you manage this kind of hardware hardware change? Did you solve that by a Hardware Abstraction Layer (HAL)? Did you have a automatical test for the HAL layer? How did you test when the hardware platform is not even ready? Do you have well documented process for this kind of change? Thanks for your insight.

  Read the article

• Hardware settings reviewing

  - by dino99

  Get some hardware related errors logged into dmesg: oem@dub:~$ dmesg | grep ata10 [ 1.007989] ata10: PATA max UDMA/133 cmd 0xa800 ctl 0xa480 bmdma 0xa408 irq 18 [ 1.691664] ata10: prereset failed (errno=-19) [ 1.691670] ata10: reset failed, giving up oem@dub:~$ dmesg | grep ata2 [ 0.990290] ata2: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfb980 irq 45 [ 1.688011] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.688055] ata2.00: unsupported device, disabling [ 1.688057] ata2.00: disabled As I understand, its related to my old Seagate SATA HDD, and the PATA CDROM. These errors are quite new, so I feel that their settings (dma, write-cache, ...) have been modified by some upgrades. I've already used hdparm to set write-cache off on the HDDs. But it seems like I need to review some other setting(s) too. With oldest distro it was easy to know about the hardware settings, but now on Quantal/Precise its deeply hidden for the average user. So i would like to know how to view/modify these settings. About the CDROM reader, the problem is different: - the system don't identify it with an UUID; but only with ATAPI or by-id oem@dub:~$ dmesg|grep 'ATAPI' [ 1.308611] ata3.00: ATAPI: TSSTcorp CDDVDW SH-S203D, SB00, max UDMA/100 oem@dub:~$ ls -l /dev/disk/by-id/ ...... lrwxrwxrwx 1 root root 9 oct. 1 06:42 ata-TSSTcorp_CDDVDW_SH-S203D -> ../../sr0 .....

  Read the article

• Partner Webcasts: EMEA Alliances & Channels Hardware Webinars, July 2012

  - by swalker

  Dear partner Oracle is pleased to invite you to the following webcasts dedicated to our EMEA partner community and designed to provide you with important news on our SPARC and Storage product portfolios. Please ensure you don't miss these unique learning opportunities! 1. How to Make Money Selling SPARC! TOMORROW: 3PM CET (2pm UKT), Tuesday, July 10, 2012 The webcast will be hosted by - Rob Ludeman, from SPARC Product Management Agenda: To bring our partners timely, valuable information, focused on increase in their success during selling SPARC systems. The webcast will be focused and targeted on specific topics and will last approximately in 30 minutes.You can submit your questions via WebEx chat and there will be a live Q&A session at the end of the webcast. REGISTER 2. Introduction to Oracle’s New StorageTek SL150 Modular Tape Library 3pm CET (2pm UK), Thursday, July 12, 2012 This webcast will help you to understand Oracle's New StorageTek SL150 Modular tape library which is the first scalable tape library designed for small and midsized companies that are experiencing high growth. Built from Oracle software and StorageTek library technology, it delivers a cost-effective combination of ease of use and scalability, resulting in overall TCO savings. During the webcast Cindy McCurley, from Tape Product Management will introduce you to the latest addition to the Oracle Tape Storage product portfolio, the SL150 Modular Tape Library. This 60 minutes webcast will cover the product’s features, positioning, unique selling points and a competitive overview on StorageTek. You can submit your questions via WebEx chat and there will be a live Q&A session at the end of the webcast. REGISTER Delivery Format This FREE online LIVE eSeminar will be delivered over the Web and Conference Call. Note: Please join the call 10 minutes before the scheduled start time. We look forward to your participation. Best regards, Giuseppe Facchetti EMEA Partner Business Development Manager, Oracle Hardware Sales Sasan Moaveni EMEA Storage Sales Manager, Oracle Hardware Sales

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >