Search Results

Search found 285 results on 12 pages for 'modprobe'.

Page 3/12 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Touchpad in Sony Vaio E14 - cannot click with a finger and drag with another - Ubuntu 12.04

    - by Nabeel
    I had the following issues with my Sony Vaio E14115's touchpad on Ubuntu 12.04: Right click not working Vertical scrolling not working Then I followed these steps to fix it: Downloaded a patch for Psmouse sudo apt-get install dkms build-essential cd ~/Desktop tar jxvf psmouse-3.2.0-24-generic-pae.tar.bz2 sudo mv psmouse-3.2.0-24-generic-pae /usr/src cd /usr/src sudo chmod -R a+rx psmouse-3.2.0-24-generic-pae sudo dkms add -m psmouse -v 3.2.0-24-generic-pae sudo dkms build -m psmouse -v 3.2.0-24-generic-pae sudo dkms install -m psmouse -v 3.2.0-24-generic-pae sudo modprobe -r psmouse sudo modprobe psmouse This fixed me the problems of Rightclick and vertical scrolling. But I still have an issue of not able to click and drag ie Clicking the leftmouse button and dragging with another finger. It doesn't move! Maybe it doesn't detect the 2nd finger. When I check the capabilities of my Synaptics touchpad by using xinput list-props "SynPS/2 Synaptics TouchPad"|grep Capabilities I get the following output: Synaptics Capabilities (304): 1, 1, 1, 1, 1, 1, 1 Please help me out.

    Read the article

  • Tp_smapi on Thinkpad T440

    - by user2597381
    I have a Thinkpad T440 with Ubuntu 14.04 (using i3wm). I have had trouble installing tp_smapi. I successfully installed it with dpkg -- can't remember whether I used apt or just downloaded it somewhere -- but I can't load the module. When I use modprobe on tp_smapi, I get this: "modprobe: ERROR: could not insert 'tp_smapi': No such device or address" Note that this is different from the error I get when I mistype the module name. I read somewhere that I might have to rebuild my kernel for it to work, but I'd thought that the kernel I was using (3.13.0-24) had that already set up. Has anyone gotten it to work? I hate how Lenovo manages the batteries!

    Read the article

  • How do I get an Xstream mobile phone working as a modem?

    - by callmegus
    I bought a CDMA mobile phone that can use as modem, this http://smartfren.com/xstream/ and i wanna try it on my ubuntu plug usb , and run "lsusb" callmegus@Presario-CQ43-304AU:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 058f:a001 Alcor Micro Corp. Bus 003 Device 002: ID 1bbb:0106 T & A Mobile Phones Bus 003 Device 003: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse Bus 004 Device 002: ID 0a5c:21e3 Broadcom Corp. I successfully "modprobe" this device, and connect to internet, but it's disconnected somehow .. and i can recconect it. I try "lsusb" again .. and something went wrong, here Bus 003 Device 002: ID 1bbb:1000 T & A Mobile Phones I do "modprobe" again and again , but it still won't connect Please guide me

    Read the article

  • Wireless doesn't connect in Ubuntu 10.04 Lxde

    - by David
    Problem I have a Dell mini 9, and the wireless has worked without trouble in Ubuntu and Xubuntu versions 8.04 and 10.04. However, after installing lxde, the wireless doesnt connect. Network manager recognizes the local networks, and will say that it is connected, but ifconfig does not confirm the connection or the existance of a wlan0. I have another Ubuntu 10.04 notebook that works fine. My wireless device is Broadcom BCM4312 802.11b/g What I have tried I have tried to remove and install network-mananager and inxi but neither work, and sudo modprobe wl returns WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.

    Read the article

  • Touchpad stopped working out of the blue

    - by KI4JGT
    So, I'm watching "The Walking Dead" and all of the sudden I lose control of my mouse through the touchpad. At first it was just for my user. I could reboot my system and switch to another user and use it just fine. I cannot explain the steps I took (I'm using the keyboard to manuver firefox right now) but it was something along the lines of: sudo modprobe -r psmouse && sudo modprobe psmouse proto=imps After this command, I regained control of my mouse but the computer didn't recognize it as a touchpad. I thought if I rebooted again, it may do the trick. So after I rebooted, the mouse went completely kaput. I cannot get the mouse to work at all now even though I've tried the command several times. I've tried different users and it's still the same.

    Read the article

  • Wifi problems after upgrading to 13.10

    - by Simon
    I just upgraded to Ubuntu 13.10, but since the upgrade I don't have internet access via wifi anymore. I can: See networks Connect to a network Ping myself (localhost, 192.168.0.103) I can't: Ping others (including other devices on the same wireless network, including the gateway/router) Resolve hosts Access any other external resource, whether on my own network or on the internet Using Wireshark, I noticed my computer is continuously sending ARP-requests like "Who has 192.168.0.1 [which is the gateway]? Tell 192.168.0.103". It doesn't get any replies though. When I ping another IP-address for which it knows the mac-address (from cache), it turns out a packet loss of 90% occurs, and even if a packet manages to arrive it takes around 3000ms. The output of route -n is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 9 0 0 eth1 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Before upgrading, wifi worked fine. Using other devices, wifi still works fine.Resetting the router didn't help. Ethernet still works after upgrading. Any suggestions? Update: I'm using the wl driver. Here's the relevant output of some commands: lspci | grep Wireless 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) cat /etc/modprobe.d/blacklist.conf [...] blacklist mac80211 blacklist brcm80211 blacklist cfg80211 blacklist lib80211_crypt_tkip blacklist lib80211 blacklist b43 cat /etc/rc.local sudo modprobe -r lib80211 sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_wep.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_tkip.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_ccmp.ko sudo modprobe wl exit 0 The last lines are probably how I got wireless working after the previous upgrade (wireless has been a problem after each upgrade). Update 2: added information about the exact hardware below. The hardware is an integrated device, so I ran lspci -nn | grep -i network. The output is: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)

    Read the article

  • WiFi on Ubuntu 12.04 custom: downloading unbearably slow

    - by Mark
    iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

    Read the article

  • How to get wireless and wired network working again on my Dell Inspiron 1501?

    - by Angelo Daul
    My wireless doesn't work with Ubuntu 12.04.(it worked with 10.04 LTS) I have a Dell Inspiron 1501. I followed the steps posted below:(from a similar tag, but...) sudo apt-get install --reinstall bcmwl-kernel-source broadcom-sta-common broadcom-sta-source echo "blacklist brcmsmac" | sudo tee -a /etc/modprobe.d/blacklist.conf echo "blacklist bcma" | sudo tee -a /etc/modprobe.d/blacklist.conf ....and now i have no Network device on my PC(wired or wireless) I can use wired conection if i start my laptop with a"previsious version of Linux"...2.26.43... I am a beginner in Linux These are my hardware: 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [ 14e4:4311] (rev 01) 08:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [ 14e4:170c] (rev 02)

    Read the article

  • ASUS VX-6 Laptop Wireless not connecting

    - by user2152790
    Someone posted a script a couple days ago, here is my output.Pastebin I can see wifi SSIDs in network, but cannot connect to mine. The only time wifi worked on 13.10 was in the Live CD, but wifi stopped working as soon as install process started. Did below but made no difference. sudo apt-get install bcmwl-kernel-source sudo modprobe -rv brcmsmac sudo modprobe -v wl What I do next? I tried Software&Updates and it showed 1 proprietary driver in use. This sounds like a WPA/WPA2 issue? Wifi works when I tried Zorin OS 7.1, wifi always worked in windows 7.

    Read the article

  • Allow access from outside network with dmz and iptables

    - by Ivan
    I'm having a problem with my home network. So my setup is like this: In my Router (using Ubuntu desktop v11.04), I installed squid proxy as my transparent proxy. So I would like to use dyndns to my home network so I could be access my server from the internet, and also I installed CCTV camera and I would like to enable watching it from internet. The problem is I cannot access it from outside the net. I already set DMZ in my modem to my router ip. My first guess is because i'm using iptables to redirect all inside network to use squid. And not allow from outside traffic to my inside network. Here is my iptables script: #!/bin/sh # squid server IP SQUID_SERVER="192.168.5.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client #modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP If you know where did I miss, please advice me. Thanks for all your help and I really appreciate it.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • ndiswrapper wlan driver installed, but wlan still does not work

    - by mugetsu
    I'm trying to get my Atheros AR1111 EB-WG PCI wireless adapter to work. Right now wifi is not even detected. I'm on ubuntu 12.04 64bit and I managed to find a xp64bit driver. I followed the exact steps here: https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper And where I do ndiswrapper -l I get something like : {name of driver} : driver installed device ({Chipset ID}) present which shows that the driver installed properly However, after I load the new module : sudo modprobe ndiswrapper nothing happens, and iwconfig shows that I still have no wlan. I tried to do dmseg | grep ndiswrapper, but there were no driver loading errors or anything strange. I also have blacklist ath5k, ath8k in /etc/modprobe.d/blacklist.conf What am I doing wrong? What could be causing this?

    Read the article

  • How can I disable ipv6 on Ubuntu Server 8.04?

    - by Boden
    I'm trying to run Dell OMSA on Ubuntu 8.04. However, it's binding to ipv6 and not to an ipv4 address. I can't seem to figure out how to change this behavior. So, since I don't need ipv6 support, I'd like to just disable it and see if that clears things up. I've tried blacklisting ipv6 in /etc/modprobe.d/blacklist (blacklist ipv6), and turning it off in /etc/modprobe.d/aliases (alias net-pf-10 off). I'm seeing both solutions recommended in forums and blogs, but neither works.

    Read the article

  • Debian Lenny - network interfaces(eth) are in DOWN state

    - by pachanga
    Folks, I'm facing a very weird problem with one of my production servers(it's Debian Lenny) - after reboot network interfaces(eth0,eth1) are in DOWN state. Looks like an Intel based networking adapter is installed on the server, lspci lists it as follows: Ethernet controller: Intel Corporation Device 10c9 (rev 01) The kernel driver responsible for this adapter is "igb". I tried "modprobe -r igb && modprobe igb", network interfaces first disappear then appear, but they are in DOWN state again. What could go wrong? It used to be working just fine. How can this be fixed?

    Read the article

  • fail2ban on server with LXC Containers

    - by RoboTamer
    The issue is modprobe and iptables don't work inside an LXC Container. LXC is the userspace control package for Linux Containers, a lightweight virtual system mechanism sometimes described as “chroot on steroids”. iptables error inside the container is: # iptables -I INPUT -s 122.129.126.194 -j DROP > iptables v1.4.8: can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. I am guessing that it can't work because the LXC containers share one kernel, the main server kernel. How do I do fail2ban in this case. modprobe and iptables work in the main server so I could install it there and link to the logfiles somehow, my guess? Any suggestions?

    Read the article

  • Enable System Beep in Ubuntu

    - by Melissa W
    I have tried and tried to get the system beep working, but with no success. I have selected System--Sound--System Beep--Enable Audible Beep (from the Gnome Desktop) I have tried from a Terminal window Edit--General Tab--Selecting terminal bell checkbox I have tried entering modprobe pcspkr at the command line. Trying echo -e '\a' or using the beep application - Nothing works! I know my hardware speaker works, because if on startup the battery is low it will beep. Update: It is a laptop computer. It is an IBM Thinkpad, iSeries. I did look at the modprobe blacklist, and pcspkr was not listed.

    Read the article

  • Linux USB to work as cd rom on mac

    - by user157483
    I am working in driver development in linux USB modules. I have written driver for usb and it is working as cd rom in windows machine 1)I made first partation as fat32 "modprobe g_hidmass file=/dev/mmcblk0p1 cdrom=1 stall=0 removable=1" this works fine in windows 2)I made first partation as hfs partation "modprobe g_hidmass file=/dev/mmcblk0p1 cdrom=1 stall=0 removable=1" but same thing i applied with hfs partation in MAC it is getting error like this "The disk you inserted was not readable by this computer" in diskutil it is shown as CD-rom but not reading the file system. frame like this Please help me how can I overcome this error...

    Read the article

  • Ubuntu 12.04 LTS Wireless Asus USB-N53 (rt3572sta) driver installation issue

    - by Jake Thompson
    My purchase of the Asus USB-N53 just came in today and I spent several hours Googling and researching drivers for this device. When I first plugged the device in it connected fine to my open system, WEP, DHCP configured access point. I opened Google Chrome and a few pages loaded, everything seemed fine. 30 seconds later... Boom! It disconnected and showed attempts to reconnect and asked for the WEP key and just showed a state of infinite connection time until it asked me for the password again. I'm using amd64 (64 bit Ubuntu desktop 12.04 LTS) The official driver can be found here although I had no luck with it. lsusb: Bus 003 Device 002: ID 0b05:179d ASUSTek Computer, Inc. uname -a Linux Jake 3.2.0-31-generic #50-Ubuntu SMP Fri Sep 7 16:16:45 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ----------------------------------------------------------------------------------Solved: I must of done something wrong when I originally installed the latest drivers from the chipset manufacturers website. I tried reinstalling and did modprobe rt3572sta and waited maybe 10 minutes??? and I connected then I rebooted and everything seems to be working so far. What I did do before hand is unplug the device and typed into the terminal (once for every source I attempted to install): cd '<directory of the driver source>' make uninstall make clean Then I went into the 2.5.0.0 directory and installed that with make make install Then I typed modprobe rt3572sta This was all in superuser. For those who don't know: sudo su

    Read the article

  • Sudo and startup script

    - by Pitto
    Hello my friends. I have a new asus 1215n and I need to digit commands to enable multitouch. No problem: I've made a script. Since this netbook also need manual activation of the wifi driver the complete script is: #!/bin/bash # # list of synaptics device properties http://www.x.org/archive/X11R7.5/doc/man/man4/synaptics.4.html#sect4 # list current synaptics device properties: xinput list-props '"SynPS/2 Synaptics TouchPad"' # sleep 5 #added delay... xinput set-int-prop "SynPS/2 Synaptics TouchPad" "Device Enabled" 8 1 xinput --set-prop --type=int --format=32 "SynPS/2 Synaptics TouchPad" "Synaptics Two-Finger Pressure" 4 xinput --set-prop --type=int --format=32 "SynPS/2 Synaptics TouchPad" "Synaptics Two-Finger Width" 9 # Below width 1 finger touch, above width simulate 2 finger touch. - value=pad-pixels xinput --set-prop --type=int --format=8 "SynPS/2 Synaptics TouchPad" "Synaptics Edge Scrolling" 1 1 0 # vertical, horizontal, corner - values: 0=disable 1=enable xinput --set-prop --type=int --format=32 "SynPS/2 Synaptics TouchPad" "Synaptics Jumpy Cursor Threshold" 250 # stabilize 2 finger actions - value=pad-pixels #xinput --set-prop --type=int --format=8 "SynPS/2 Synaptics TouchPad" "Synaptics Tap Action" 0 0 0 0 1 2 3 # pad corners rt rb lt lb tap fingers 1 2 3 (can't simulate more then 2 tap fingers AFAIK) - values: 0=disable 1=left 2=middle 3=right etc. (in FF 8=back 9=forward) xinput --set-prop --type=int --format=8 "SynPS/2 Synaptics TouchPad" "Synaptics Two-Finger Scrolling" 1 0 # vertical scrolling, horizontal scrolling - values: 0=disable 1=enable #xinput --set-prop --type=int --format=8 "SynPS/2 Synaptics TouchPad" "Synaptics Circular Scrolling" 1 #xinput --set-prop --type=int --format=8 "SynPS/2 Synaptics TouchPad" "Synaptics Circular Scrolling Trigger" 3 sudo modprobe lib80211 sudo insmod /home/pitto/Drivers/broadcom/wl.ko exit I've saved the script, then put it in my home, then chmod +x scriptname and then added it to startup applications. Then I did: sudo visudo and added this row: myusername ALL=(ALL) NOPASSWD: /home/scriptname rebooted and... Multitouch works but wifi not. When I manually launch the script it asks for sudo password so I thought it was because of modprobe and insmod commands and I've added those commands to sudo visudo. Nothing. What am I doing wrong?

    Read the article

  • How to get Broadcom BCM 43XX Wireless card working

    - by Fer1805
    NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • USB drives not recognized all of a sudden

    - by Siddharth
    I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. lsusb results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful. Thanks.

    Read the article

  • Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

    - by Josh
    As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

    Read the article

  • Bluetooth adapter turned from working fine to unrecognized

    - by easoncxz
    i had been using bluetooth fine, with devices working, but today when i turned on my computer again bluetooth strangely failed. there is a bluetooth icon on the top bar, showing "bluetooth on", but if i click on the "bluetooth settings" item, a system settings window shows up and shows me a bluetooth on-off switch which is disabled (i.e. fixed to off). more information about my case: i am a new linux used, coming from windows, and do not know supposedly-obvious commands. i am using a laptop. it initially doesn't have bluetooth. i bought a built-in type (instead of USB type) bluetooth module, and added it inside the laptop. hence, i do not have a specific FN+* key for bluetooth. in windows, i needed to install an additional driver that was intended for other machines in my laptop's seires which have built-in (i.e. factoryly built-in)j bluetooth modules. the Fn+* key seemed to only affect wifi under ubuntu. i have been successfully using magicmouse with my later-added built-in bluetooth module/adapter on both windows and ubuntu i have been trying to tweak the magicmouse scrolling speed with commands rmmod something, modprobe hid_magicmouse --scroll_speed=45 --scroll_acceleration=30 or something, then added a file `/etc/modprobe.d/magicmouse.conf". the mouse seemed to be working fine with these changes. now if i run commands like hcitool dev, the shell tells me that i do not have any "Devices" or "adapters". i seem to have bluez installed, because when i type "blue" then tab-autocomplete, a bunch of commands like bluez-test-device pops up. -- update -- some commands and their results: easoncxz@eason-Aspire-4741-ubuntu:/etc$ hcitool dev Devices: easoncxz@eason-Aspire-4741-ubuntu:/etc$ hcitool scan Device is not available: No such device easoncxz@eason-Aspire-4741-ubuntu:/etc$ rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no easoncxz@eason-Aspire-4741-ubuntu:/etc$ rfkill list 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no

    Read the article

  • How do I get a Broadcom BCM4311 working?

    - by Fer1805
    I'm having serious problems installing the broadcom drivers for ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. Broadcom BCM4311 Wireless not working Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >