Search Results

Search found 285 results on 12 pages for 'modprobe'.

Page 4/12 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Problem with sound driver

  - by JiminP

  I had problem that sound had lag in Flash. (Other than that, there was no problem.) On the internet, I found that installing OSS4 might help me. So I installed OSS4, but there was some problems (no sound on Flash, and couldn't use function key on the laptop - which is quite annoying), so I try to remove OSS4 and re-installing sound modules. After some mess-up, the whole sound was gone. I used Ubuntu for a year, but I don't know how to use the terminal well (All I know is basic commands like sudo, ls, or apt-get).. Now I'm trying to recover by following instructions at this page, but I have some problems... :( When I try to follow instructions: sudo aplay -l finds no sound drivers. find /lib/modules/'uname -r' | grep snd (backtick changed to ' due to code markup) returns nothing. When I try to do sudo apt-get install linux-restricted-modules-'uname -r' linux-generic, it says that it can't find linux-restricted-modules-3.0.0-13-generic package. lspci -v | grep -A7 -i "audio" returns this, which doesn't contain anything about the name of the driver. Writing sudo modprobe sn and pressing tab twice only returns sudo modprobe sn9c102. sudo aptitude --purge reinstall linux-sound-base alsa-base alsa-utils linux-image-'uname -r' linux-ubuntu-modules-'uname -r' libasound2 returns this, and didn't change non of above. sudo apt-get install linux-alsa-driver-modules-$(uname -r) fails because it can't find the package linux-alsa-driver-modules-3.0.0-13-generic. Compiling ALSA driver doesn't work. When I try to make, it says that /lib/modules/3.0.0-13-generic/build/include/linux/modversions.h doesn't exist. I'm using Ubuntu 11.10. Can anyone help me? I can re-install Ubuntu, but I don't want to....

  Read the article

• BCM4306, b43 legacy driver installed, but "firmware missing" error

  - by ScrollerBlaster

  I have the following wireless hardware on a Compaq evo N600c laptop running lubuntu latest. ciaran@compaq:~$ lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03) Following the instructions from here : http://www.linuxwireless.org/en/users/Drivers/b43#b43_and_b43legacy I opted for the legacy firmware installer, following instructions for internet install to the letter (with no errors). i.e. I successfully installed sudo apt-get install firmware-b43legacy-installer In the nm-applet I now get Wireless networks device not ready (firmware missing) I open up Additional Drivers, but the list is empty. I have commented out this line in /etc/modprobe.d/blacklist.conf #blacklist bcm43xx Contents of firmware dir: ciaran@compaq:/etc/modprobe.d$ sudo ls /lib/firmware/b43legacy/ [sudo] password for ciaran: a0g0bsinitvals2.fw a0g0initvals5.fw b0g0bsinitvals2.fw b0g0initvals5.fw ucode11.fw ucode5.fw a0g0bsinitvals5.fw a0g1bsinitvals5.fw b0g0bsinitvals5.fw pcm4.fw ucode2.fw a0g0initvals2.fw a0g1initvals5.fw b0g0initvals2.fw pcm5.fw ucode4.fw Edit: from dmesg: [ 4460.193382] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found [ 4460.193393] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found [ 4460.193401] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website. Yours in hope.

  Read the article

• iptables unresolved dependencies

  - by tertle

  I'm trying to setup OpenVPN Access Server on a VPS running ubuntu 9.10 for a friend so she can play games from her uni campus. The problem is I keep running into this error when trying to start openvpn. Service deferred error: IPTablesServiceBase: failed to run iptables-restore [status=1]: ['FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'iptables-restore: line 46 failed']: internet/base:1175,internet/base:752,internet/process:45,internet/process:306,internet/_baseprocess:48,internet/process:775,internet/_baseprocess:60,svc/pp:116,svc/svcnotify:26,internet/defer:238,internet/defer:307,internet/defer:323,sagent/ipts:105,sagent/ipts:39,util/error:52,util/error:32 service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['iptables_openvpn']) Now I've already got my provider to enabled the TUN/TAP device driver and I checked this using # cat /dev/net/tun Which returned “File descriptor in bad state” Which I believe means it's enabled. After extensive searching, I've been unable to find any solution other than people suggesting to make sure TUN/TAP device driver is enabled. Any ideas on how to solve my issue? I'm not very experience with linux and I feel in over my head here so any advice is greatly appreciated. --edit-- Just stumbled across this Not sure how I missed it earlier. I believe I need to get modprobe ipt_mark & modprobe ipt_MARK run on the hostnode by my provider. Is this correct and something I should try get done.

  Read the article

• Ubuntu stops using Nvidia driver after kernel upgrade

  - by Daniel

  Just updated and restarted, Ubuntu's doesn't display correctly. After restart, the desktop now looks like this. I've temporarily switched to the Nouveau driver. The update history reveals the kernel was updated, amongst many things; and the following were installed: linux-image-3.5.0-19-generic (3.5.0-19.30) linux-image-extra-3.5.0-19-generic (3.5.0-19.30) I've encountered this type of problem quite recently, so I decided to reapply the same steps, to solve the problem, as follows: sudo apt-get install linux-headers-3.5.0-19 sudo apt-get install linux-headers-3.5.0-19-generic sudo depmod -a sudo modprobe nvidia sudo /etc/init.d/*dm restart When installing linux-headers-3.5.0-19-generic, I get an error, message from terminal as follows: Setting up linux-headers-3.5.0-19-generic (3.5.0-19.30) ... Examining /etc/kernel/header_postinst.d. run-parts: executing /etc/kernel/header_postinst.d/dkms 3.5.0-19-generic /boot/vmlinuz-3.5.0-19-generic Error! Problems with depmod detected. Automatically uninstalling this module. DKMS: Install Failed (depmod problems). Module rolled back to built state. However, I ignored the above error and continued the steps with sudo depmod -a, installed nvidia-current, then did sudo modprobe nvidia, which yielded the following error: FATAL: Error inserting nvidia_current (/lib/modules/3.5.0-19-generic/updates/dkms/nvidia_current.ko): No such device Upon restart, the Nvidia driver now works! BTW, do those error messages imply I broke something? Just curious, cause I don't want to get happy I've fixed it, then it stops working later on. The system is Dell XPS-L702X, with NVIDIA GeForce GT 555M, and 17" screen.

  Read the article

• Nivida driver install

  - by Adham

  tried black listing and every thing i could find on the internet used with root and alt+ctrl+f1 with no solution nvidia-installer log file '/var/log/nvidia-installer.log' creation time: Mon Jun 17 08:35:25 2013 installer version: 319.23 PATH: /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin nvidia-installer command line: ./nvidia-installer Using: nvidia-installer ncurses user interface -> License accepted. -> Installing NVIDIA driver version 319.23. -> Running distribution scripts executing: '/usr/lib/nvidia/pre-install'... -> done. -> The distribution-provided pre-install script failed! Continue installation anyway? (Answer: Yes) ERROR: The Nouveau kernel driver is currently in use by your system. This driver is incompatible with the NVIDIA driver, and must be disabled before proceeding. Please consult the NVIDIA driver README and your Linux distribution's documentation for details on how to correctly disable the Nouveau kernel driver. WARNING: One or more modprobe configuration files to disable Nouveau are already present at: /etc/modprobe.d/nvidia-installer-disable-nouveau.conf. Please be sure you have rebooted your system since these files were written. If you have rebooted, then Nouveau may be enabled for other reasons, such as being included in the system initial ramdisk or in your X configuration file. Please consult the NVIDIA driver README and your Linux distribution's documentation for details on how to correctly disable the Nouveau kernel driver. ERROR: Installation has failed. Please see the file '/var/log/nvidia-installer.log' for details. You may find suggestions on fixing installation problems in the README available on the Linux driver download page at www.nvidia.com.

  Read the article

• Uninstalling ATI's drivers and installing NVIDIA's?

  - by whydidithavetobreak

  I replaced my card but I'm not sure how to set things up on Ubuntu. When the computer boots, it doesn't start GDM (I think that's what it's called). Instead, it asks me to log in the command line. If I try to do a startx, it tells me there is no AMD device connected or something to that extent. I originally installed the ATI drivers using the GUI. It said that I was using the limited drivers or something to that extent with a popup on the right of one of the taskbars, so I clicked there and updated it. I think it could also be reached by going to system administration restricted drivers or something close to that. I tried installing the nivida drivers by doing a "sudo apt-get install nvidia-glx-185" and then doing "sudo modprobe nvidia" and "sudo nvidia-xconfig" as this guy says but that didn't work. Modprobe couldn't find anything related to Nvidia and nvidia-xconfig wasn't an available command for me. Since I wasn't sure how to remove the ATI drivers I did that without messing with them. Not sure if that was a good idea.

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• Getting error message when trying to start a virtual machine

  - by Sunil J

  I have been using VMWare on Windows for a long time. But after a long wait, I moved to VirtualBox on Ubuntu 11.10. I installed Ubuntu, 32 Bit, installed all available updates and installed Virtual Box. When I try to create a new Windows installation inside VirtualBox, I got the following error messages. 1st error dialogue VirtualBox - Error Failed to open a session for the virtual machine Windows XP.<br> The virtual machine '**Windows XP**' has terminated unexpectedly during startup with exit code 1.<p> Details<p> Result Code: <br> NS_ERROR_FAILURE (0x80004005)<br> Component: <br> Machine<br> Interface: <br> IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}<p> 2nd error dialogue **Virtualbox - Error in suplibOsinit**<br> **Kernal driver not installed (rc--1908)**<br> Please install the virtualbox-dkmbs package and execute 'modprobe vboxdrv' as root.<p> Steps I tried I have already tried reinstalling VirtualBox. Google result seem to indicate the the problem happens due to Kernel updates. Is there anyway I can get this working? I need this for malware analysis and if VirtualBox is going to crash on me all the time, then I won't be able to use Ubuntu for work. Output to dpkg -l | grep virtual server rc virtualbox 4.1.2-dfsg-1ubuntu1 x86 virtualization solution - base binaries rc virtualbox-qt 4.1.2-dfsg-1ubuntu1 x86 virtualization solution - Qt based user interface cute 'modprobe vboxdrv' as root.<p>

  Read the article

• Touchpad won't work/not recognized on laptop, Ubuntu 11.10

  - by The_McManus_Position

  When I start out running 11.10 (Ocelot) from the Live CD the touchpad works with no problem. Once installing however the touchpad does not work at all. I have installed all updates available. I have tried installing the synaptiks touchpad package and the gpointer package from the software manager, this did not help. Under System Settings - Mouse and Touchpad there is only a mouse tab, no touchpad tab. It seems my touchpad is not even recognized. I have tried running several things in the terminal that I have found under similar questions, but I always get errors about the files not being found, or the drivers not being found. Have tried: sudo modprobe -r psmouse sudo modprobe psmouse proto=imps This results in an error message. dconf-editor Can load the GUI, but after that I can't seem to navigate through it to find the files that need editing. Read what's listed here. But I've got no GRUB, running only Ubuntu. As you can see I've been trying several things and nothing has worked so far, would appreciate any help. Thanks!

  Read the article

• How do I install Intel ethernet drivers?

  - by Pat

  I just bought a Lenovo T420, I booted the live CD and couldn't connect to my wireless router so I figured I needed the drivers for it. I have the last version of Ubuntu(12.04). It's a Intel® 82579 Gigabit Ethernet Controller So I went on intel's website and downloaded the Drivers for Linux and compiled them with make install. Here's the tutorial I followed: Linux Driver Install I have a few question though, What are these doing : modprobe e1000e ifconfig eth0 up dhclient eth0 ping intel.com As far as what I've read, modprobe seems to add the driver to the list of drivers for the kernel, but is that operation only good for one session? The two other lines, I don't understand either what they are doing. What does he mean at the end when he mentions : Note: Whenever the kernel version is upgraded you will need rebuild this driver. And are these steps permanent? Or do I have to add them to some boot.conf file for everytime I boot. Anyways, the steps worked for me and I have established a connection with my router, I just need to know if I need to do additional steps to keep the driver permanently etc.

  Read the article

• How to get sound on macbook pro 4,1

  - by Thomas

  I have just installed Xubuntu 12.04.2. My soundcard is detected: thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 Everything is put to max in alsamixer and nothing is muted (all the sliders are on OO. My speakers do not work, but when I plug in a headphone I hear it very soft. When I connect my stereo and put the sound VERY loud (3-blocks-of-complaining-neighbours loud) I hear it on a normal level but crackling. I added options snd-hda-intel model=mbp5 amixer set IEC958 off to at the end of /etc/modprobe.d/alsa-base.conf. When it's still not working I tried everything here: https://help.ubuntu.com/community/SoundTroubleshooting 1 >>> list-sinks 1 sink(s) available. * index: 0 name: <alsa_output.pci-0000_00_1b.0.analog-stereo> driver: <module-alsa-card.c> flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE priority: 9959 volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 base volume: 100% 0.00 dB volume steps: 65537 muted: no current latency: 0.00 ms max request: 0 KiB max rewind: 0 KiB monitor source: 0 sample spec: s16le 2ch 44100Hz channel map: front-left,front-right Stereo used by: 0 linked by: 0 configured latency: 0.00 ms; range is 0.50 .. 371.52 ms card: 0 <alsa_card.pci-0000_00_1b.0> module: 4 properties: alsa.resolution_bits = "16" device.api = "alsa" device.class = "sound" alsa.class = "generic" alsa.subclass = "generic-mix" alsa.name = "ALC889A Analog" alsa.id = "ALC889A Analog" alsa.subdevice = "0" alsa.subdevice_name = "subdevice #0" alsa.device = "0" alsa.card = "0" alsa.card_name = "HDA Intel" alsa.long_card_name = "HDA Intel at 0x9b500000 irq 46" alsa.driver_name = "snd_hda_intel" device.bus_path = "pci-0000:00:1b.0" sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card0" device.bus = "pci" device.vendor.id = "8086" device.vendor.name = "Intel Corporation" device.product.name = "82801H (ICH8 Family) HD Audio Controller" device.form_factor = "internal" device.string = "front:0" device.buffering.buffer_size = "65536" device.buffering.fragment_size = "32768" device.access_mode = "mmap+timer" device.profile.name = "analog-stereo" device.profile.description = "Analog Stereo" device.description = "Built-in Audio Analog Stereo" alsa.mixer_name = "Realtek ALC889A" alsa.components = "HDA:10ec0885,106b3a00,00100103" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" ports: analog-output-speaker: Speakers (priority 10000, available: unknown) properties: analog-output-headphones: Headphones (priority 9000, available: no) properties: active port: <analog-output-speaker> 2 and 3: Doesn't seem an permission issue, the sound is very far away (See opening paragraph). 4 thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 5 thomas@thomas-pc:~$ find /lib/modules/`uname -r` | grep snd /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-hwdep.ko /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-pcm.ko [.. huge lists continues ..] /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/pdaudiocf/snd-pdaudiocf.ko /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/vx/snd-vxpocket.ko thomas@thomas-pc:~$ 6 thomas@thomas-pc:~$ lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) Subsystem: Apple Inc. Device 00a4 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at 9b500000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 7 I guess it's supported. Linux mint and Xubuntu 13.04 had no trouble with sounds. Everything worked out of the box Thanks in advance Edit: alsa-info.sh output: WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' ALSA Information Script v 0.4.62 -------------------------------- This script visits the following commands/files to collect diagnostic information about your ALSA installation and sound related hardware. dmesg lspci lsmod aplay amixer alsactl /proc/asound/ /sys/class/sound/ ~/.asoundrc (etc.) See './alsa-info.sh --help' for command line options. WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' Automatically upload ALSA information to www.alsa-project.org? [y/N] : y Uploading information to www.alsa-project.org ... Done! Your ALSA information is located at http://www.alsa-project.org/db/?f=6cffc584284d4c0b266eb53249824ef83d6c4e3e Please inform the person helping you. thomas@thomas-pc:~$

  Read the article

• Wireless Problem on Acer Aspire 5610z

  - by Ugur Can Yalaki

  I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• ath9k driver does not weak up

  - by shantanu

  I know this is common question but i found no suitable answer, so i am asking this again. I installed ubuntu 11.10. I found the bug for ath9k, so set first network boot from BIOS menu. That's worked. I have upgraded to 12.04 yesterday. Now ath9k is creating problem again. First network boot is still enable. ath9k works at start. But failed(connect again and again) after couple of minutes. dmesg show error that it can not weak up in 500us. So i tried #compat-wireless-3.5.1-1. But result is same. I have also added #nohwcrypt=1 option in /etc/modeprob.d/ath9k.conf. Still no luck. I tried #rmmod and then modprobe sudo modprobe ath9k nohwcrypt=1 dmesg shows me error: [ 400.690086] ath9k: Driver unloaded [ 406.214329] ath9k 0000:06:00.0: enabling device (0000 -> 0002) [ 406.214348] ath9k 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 406.214368] ath9k 0000:06:00.0: setting latency timer to 64 [ 406.428517] ath9k 0000:06:00.0: Failed to initialize device [ 406.428852] ath9k 0000:06:00.0: PCI INT A disabled [ 406.428887] ath9k: probe of 0000:06:00.0 failed with error -5 dmesg error when driver fail: 355.023521] ath: Chip reset failed [ 355.023524] ath: Unable to reset channel, reset status -22 [ 355.023556] ath: Unable to set channel [ 355.088569] ath: Failed to stop TX DMA, queues=0x10f! [ 355.122708] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff [ 355.122714] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up [ 355.263962] ath: Chip reset failed [ 355.263966] ath: Unable to reset channel (2437 MHz), reset status -22 [ 358.996063] ath: Failed to wakeup in 500us [ 364.004182] ath: Failed to wakeup in 500us I can not install fresh ubuntu because i have lots of application installed. System : Acer Aspire 4250 AMD dual core 1.6GHZ Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) EDITED Now i am in serious problem. No wifi device is not showing in ifconfig or lshw commands. Only ether-net interface shows. I tried (FN + WIFI) several times to enable the device but nothing helps. Now I have installed fresh ubuntu 12.04. Please help lshw -c network: *-network description: Ethernet interface product: 82566DC Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 02 serial: 00:19:d1:7a:8e:f9 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.0.0-k duplex=full firmware=1.1-0 ip=192.168.1.114 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:90300000-9031ffff memory:90324000-90324fff ioport:20c0(size=32) rfkill command does not show anything but no error.

  Read the article

• Ubuntu doesn't let me to blacklist modules

  - by László Monda

  I'd like to blacklist a couple of modules, namely drm, drm_kms_helper, i2c_algo_bit and i915 to not allow my integrated Intel GPU to ever be used, but instead my Nvidia MXM card. I inserted the following lines into /etc/modprobe.d/blacklist.conf: blacklist i915 blacklist drm blacklist drm_kms_helper blacklist i2c_algo_bit Despite the above right after rebooting my laptop and typing lsmod I can see these modules loaded. Why does my blacklist get utterly disrespected and what can I do about it?

  Read the article

• Wireless Drivers for Broadcom BCM 4321 (14e4:4329) will not stay connected to a wireless network

  - by Eugene

  So, I'm not necessary new to Linux, I just never took the time to learn it, so please, bare with me. I just swapped out one of my wireless cards from one computer to another. This wireless card in question would be a "Broadcom BCM4321 (14e4:4329)" or actually a "Netgear WN311B Rangemax Next 270 Mbps Wireless PCI Adapter", but that's not important. I've tried (but probably screwed up in the process) installing the "wl" , "b43" and "brcmsmac" drivers, or at least I think I did. Currently I have only the following drivers loaded: eugene@EugeneS-PCu:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd The main issue is that with most of the drivers available that I've installed, they will find my wireless network but, they will only stay connected for about a minute with abnormally slow speed and then all of a sudden disconnect. Currently, the computer is hooked into another to share it's connect so that I can install drivers from the internet instead of loading them on to a flash drive and doing it offline. If anyone has any insight to the problem, that would be awesome. If not, I'll probably just look up how to install the Windows closed source driver. Edit 1: Even when I try the method here, as suggested when this was marked as a duplicate, I still can't stay connected to a wireless network. Edit 2: After discussing my issue with @Luis, he opened my question back up and told me to include the tests/procedures in the comments. Basically I did this: Read the first answer of the link above when this question was marked as duplicate which involved installing removing bcmwl-kernel-source and instead install firmware-b43-installer and b43-fwcutter. No change of result and contacted Luis in the comments, who then told me to try the second answer which involved removing my previous mistake and installing bcmwl-kernel-source Now the Network Manger (this has happend before, but usally I fixed it by using a different driver) even recognizes WiFi exist (both non-literal and literal). Luis who then suggested sudo rfkill unblock all rfkill unblock all didn't return anything, so I decide to try sudo rfkill list all. Returns nothing (no wonder rfkill unblock all did nothing). I enter lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" and that returns nothing. Try loading the driver by entering sudo modprobe b43 and try lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" again. Returns this: eugene@Eugenes-uPC:~$ sudo modprobe b43 eugene@Eugenes-uPC:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd So to recap: Currently Network Manager doesn't recognize Wireless exists, b43 drivers are loaded and I've currently hardwired a connect from my laptop to the computer that's causing this.

  Read the article

• Installing Canon LBP6000 in Ubuntu 12.04

  - by MMA

  This is really frustrating. I am trying to install LBP6000 in Ubuntu 12.04 without any success. (Well, I had success about a week back when I first bought the printer and finally printed pages after a struggle of several hours. Then today it suddenly stopped working and I uninstalled everything and started from scratch. Now, I seem to have lost the way.) My steps Downloaded the latest Canon driver from Canon site. File Linux_CAPT_PrinterDriver_V240_uk_EN.tar.gz Got the radu script (I am allowed only two hyperlinks, so can not put the link here. You can Google radu Canon) Changed the /etc/modprobe.d/blacklist-cups-usblp.conf file as instructed in, Official Documentation. (See the section Ubuntu 12.04 Install). Now this file looks like, # cups talks to the raw USB devices, so we need to blacklist usblp to avoid # grabbing them # blacklist usblp Rebooted my machine Changed the port in radu script to 59787 as instructed in the link at step 3. (Again see the section Ubuntu 12.04 Install, or see the comment at How to Install Canon LBP Printers in Ubuntu. Also put the latest deb files from step 1 in the appropriate directory of this script. Ran the radu script. A printer, LBP6000 got added. Not two printers, one to be disabled, as appeared in the message on the terminal after running the script. sudo /etc/init.d/ccpd status shows, Canon Printer Daemon for CUPS: ccpd: 3142 3139 Results The printer does not print. Printer state (from System Setting-Printing, or at cups http interface localhost:631/printers/LBP6000) goes from Idle to Processing, a job appears in print queue, and then the job disappears and the printer state goes back to Idle. The actual printer does not even blink. Diagnostics (got help from the link in step 3, Troubleshooting) captstatusui -P LBP6000 shows communication error lsmod | grep usblp did not show anything. After running, sudo modprobe usblp, shows usblp 17885 0 However, ls -l /dev/usb/lp0 gives, ls: cannot access /dev/usb/lp0: No such file or directory /var/ccpd did not exist, created, sudo mkdir /var/ccpd sudo mkfifo /var/ccpd/fifo0 sudo chown -R lp:lp /var/ccpd Any suggestion will be appreciated. Do not know what to do.

  Read the article

• Modules loading despite being added to the blacklist

  - by László Monda

  I'd like to blacklist a couple of modules, namely drm, drm_kms_helper, i2c_algo_bit and i915 to forbid my integrated Intel GPU to be used, but to use my Nvidia MXM card instead. I inserted the following lines into /etc/modprobe.d/blacklist.conf: blacklist i915 blacklist drm blacklist drm_kms_helper blacklist i2c_algo_bit Despite the above right after rebooting my laptop and typing lsmod I can see these modules loaded. Why does my blacklist get utterly disrespected and what can I do about it?

  Read the article

• permanently load module

  - by Radu

  I have a Compaq Presario CQ-61 320SQ, I am using Ubuntu 10.04 because after update to 10.10 my mouse and touchpad won't work, network won't work, sound won't work ... (I managed to fix most of them after almost a month of googling, but not all, my 2 Desktops have no problem with 10.10) so I decided to switch back to 10.04, where I have a problem: My broadband speed is very low beacause of the kernel module r8169, I downloaded the good module r8101 and every time the computer boots have a rc.local entry to fix this. Question: Can I load the modul permanently from a specific location. I heard about /etc/modules but there I need the module name, but I have to load it from a specific path (where is the default path for that) Thank you. So I studied the script: It creates the file r8101.ko in /lib/modules/uname -r/kernel/drivers/net so I think as long as nobody will delete that file, and I don't update the kernel, maybe adding r8108 to /etc/modules will work, and add r8169 to blacklist ... I will give it a try. EDIT2: So I added r8101 to /etc/modules and blacklist r8169 to /etc/modprobe.d/blacklist.conf It still uses the old module, lsmod prints: radu@adu:~$ lsmod | grep r8 r8101 67626 0 r8169 34108 0 mii 4381 1 r8169 EDIT: the module is loaded using this script that came with it: #!/bin/sh # invoke insmod with all arguments we got # and use a pathname, as insmod doesn't look in . by default TARGET_PATH=/lib/modules/`uname -r`/kernel/drivers/net echo echo "Check old driver and unload it." check=`lsmod | grep r8169` if [ "$check" != "" ]; then echo "rmmod r8169" /sbin/rmmod r8169 fi check=`lsmod | grep r8101` if [ "$check" != "" ]; then echo "rmmod r8101" /sbin/rmmod r8101 fi echo "Build the module and install" echo "-------------------------------" >> log.txt date 1>>log.txt make all 1>>log.txt || exit 1 module=`ls src/*.ko` module=${module#src/} module=${module%.ko} if [ "$module" == "" ]; then echo "No driver exists!!!" exit 1 elif [ "$module" != "r8169" ]; then if test -e $TARGET_PATH/r8169.ko ; then echo "Backup r8169.ko" if test -e $TARGET_PATH/r8169.bak ; then i=0 while test -e $TARGET_PATH/r8169.bak$i do i=$(($i+1)) done echo "rename r8169.ko to r8169.bak$i" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak$i else echo "rename r8169.ko to r8169.bak" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak fi fi fi echo "Depending module. Please wait." depmod -a echo "load module $module" modprobe $module echo "Completed." exit 0

  Read the article

• USB drives not recognized all of a sudden (module usb_storage not loading)

  - by Siddharth

  I am very close to the solution, just need to know how to get usb-storage to load I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• USB drives not recognized all of a sudden (usb_storage not loaded lsmod does not report usb_storage)

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• Tracing Silex from PHP to the OS with DTrace

  - by cj

  In this blog post I show the full stack tracing of Brendan Gregg's php_syscolors.d script in the DTrace Toolkit. The Toolkit contains a dozen very useful PHP DTrace scripts and many more scripts for other languages and the OS. For this example, I'll trace the PHP micro framework Silex, which was the topic of the second of two talks by Dustin Whittle at a recent SF PHP Meetup. His slides are at Silex: From Micro to Full Stack. Installing DTrace and PHP The php_syscolors.d script uses some static PHP probes and some kernel probes. For Oracle Linux I discussed installing DTrace and PHP in DTrace PHP Using Oracle Linux 'playground' Pre-Built Packages. On other platforms with DTrace support, follow your standard procedures to enable DTrace and load the correct providers. The sdt and systrace providers are required in addition to fasttrap. On Oracle Linux, I loaded the DTrace modules like: # modprobe fasttrap # modprobe sdt # modprobe systrace # chmod 666 /dev/dtrace/helper Installing the DTrace Toolkit I download DTraceToolkit-0.99.tar.gz and extracted it: $ tar -zxf DTraceToolkit-0.99.tar.gz The PHP scripts are in the Php directory and examples in the Examples directory. Installing Silex I downloaded the "fat" Silex .tgz file from the download page and extracted it: $ tar -zxf silex_fat.tgz I changed the demonstration silex/web/index.php so I could use the PHP development web server: <?php // web/index.php $filename = __DIR__.preg_replace('#(\?.*)$#', '', $_SERVER['REQUEST_URI']); if (php_sapi_name() === 'cli-server' && is_file($filename)) { return false; } require_once __DIR__.'/../vendor/autoload.php'; $app = new Silex\Application(); //$app['debug'] = true; $app->get('/hello', function() { return 'Hello!'; }); $app->run(); ?> Running DTrace The php_syscolors.d script uses the -Z option to dtrace, so it can be started before PHP, i.e. when there are zero of the requested probes available to be traced. I ran DTrace like: # cd DTraceToolkit-0.99/Php # ./php_syscolors.d Next, I started the PHP developer web server in a second terminal: $ cd silex $ php -S localhost:8080 -t web web/index.php At this point, the web server is idle, waiting for requests. DTrace is idle, waiting for the probes in php_syscolors.d to be fired, at which time the action associated with each probe will run. I then loaded the demonstration page in a browser: http://localhost:8080/hello When the request was fulfilled and the simple output of "Hello" was displayed, I ^C'd php and dtrace in their terminals to stop them. DTrace output over a thousand lines long had been generated. Here is one snippet from when run() was invoked: C PID/TID DELTA(us) FILE:LINE TYPE -- NAME ... 1 4765/4765 21 Application.php:487 func -> run 1 4765/4765 29 ClassLoader.php:182 func -> loadClass 1 4765/4765 17 ClassLoader.php:198 func -> findFile 1 4765/4765 31 ":- syscall -> access 1 4765/4765 26 ":- syscall <- access 1 4765/4765 16 ClassLoader.php:198 func <- findFile 1 4765/4765 25 ":- syscall -> newlstat 1 4765/4765 15 ":- syscall <- newlstat 1 4765/4765 13 ":- syscall -> newlstat 1 4765/4765 13 ":- syscall <- newlstat 1 4765/4765 22 ":- syscall -> newlstat 1 4765/4765 14 ":- syscall <- newlstat 1 4765/4765 15 ":- syscall -> newlstat 1 4765/4765 60 ":- syscall <- newlstat 1 4765/4765 13 ":- syscall -> newlstat 1 4765/4765 13 ":- syscall <- newlstat 1 4765/4765 20 ":- syscall -> open 1 4765/4765 16 ":- syscall <- open 1 4765/4765 26 ":- syscall -> newfstat 1 4765/4765 12 ":- syscall <- newfstat 1 4765/4765 17 ":- syscall -> newfstat 1 4765/4765 12 ":- syscall <- newfstat 1 4765/4765 12 ":- syscall -> newfstat 1 4765/4765 12 ":- syscall <- newfstat 1 4765/4765 20 ":- syscall -> mmap 1 4765/4765 14 ":- syscall <- mmap 1 4765/4765 3201 ":- syscall -> mmap 1 4765/4765 27 ":- syscall <- mmap 1 4765/4765 1233 ":- syscall -> munmap 1 4765/4765 53 ":- syscall <- munmap 1 4765/4765 15 ":- syscall -> close 1 4765/4765 13 ":- syscall <- close 1 4765/4765 34 Request.php:32 func -> main 1 4765/4765 22 Request.php:32 func <- main 1 4765/4765 31 ClassLoader.php:182 func <- loadClass 1 4765/4765 33 Request.php:249 func -> createFromGlobals 1 4765/4765 29 Request.php:198 func -> __construct 1 4765/4765 24 Request.php:218 func -> initialize 1 4765/4765 26 ClassLoader.php:182 func -> loadClass 1 4765/4765 89 ClassLoader.php:198 func -> findFile 1 4765/4765 43 ":- syscall -> access ... The output shows PHP functions being called and returning (and where they are located) and which system calls the PHP functions in turn invoked. The time each line took from the previous one is displayed in the third column. The first column is the CPU number. In this example, the process was always on CPU 1 so the output is naturally ordered without requiring post-processing, or the D script requiring to be modified to display a time stamp. On a terminal, the output of php_syscolors.d is color-coded according to whether each function is a PHP or system one, hence the file name. Summary With one tool, I was able to trace the interaction of a user application with the operating system. I was able to do this to an application running "live" in a web context. The DTrace Toolkit provides a very handy repository of DTrace information. Even though the PHP scripts were created in the time frame of the original PHP DTrace PECL extension, which only had PHP function entry and return probes, the scripts provide core examples for custom investigation and resolution scripts. You can easily adapt the ideas and and create scripts using the other PHP static probes, which are listed in the PHP Manual. Because DTrace is "always on", you can take advantage of it to resolve development questions or fix production situations.

  Read the article

• How to activate subwoofer in Inspiron 17r?

  - by alfC

  I have a Dell Inspiron 17r, after a fresh install of 12.10, the subwoofer seems to be not utilized. No sound comes from it and in the Sound Control Panel the settings appear grayed out (see screenshot). How can I activate the subwoofer? I tried adding the line options snd-hda-intel model=dell in the file /etc/modprobe.d/alsa-base.conf and enable-lfe-remixing = yes default-sample-channels = 3 in the file /etc/pulse/daemon.conf, but still doesn't work.

  Read the article

• How to get D-Link DWA-547 working on Ubuntu 13.10?

  - by Tan Kah Ping

  I got a D-Link DWA-547 Wifi card which is supposed to work out-of-the-box with Linux. Says so here: http://wireless.kernel.org/en/users/Drivers/ath9k/products/external While lspci does list the device, NetworkManager doesn't seem to allow me to configure Wifi. lsmod also shows that ath9k isn't loaded. Manually loading with 'modprobe ath9k' doesn't help. How do I get this card working on Ubuntu 13.10 64-bit?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >