Search Results

Search found 1317 results on 53 pages for 'sata'.

Page 3/53 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Identify SATA hard drive

  - by Rob Nicholson

  Very similar question to: Physically Identify the failed hard drive But for Windows 2003 this time. Scenario: Four identical SATA hard drives plugged into motherboard (no RAID controller here) Configured as single drive in Windows as a spanned volume One of them is starting to fail with error "The driver detected a controller error on \Device\Harddisk3" How do you cross-reference Harddisk3 to the physical SATA connection on the motherboard so you know which drive to replace? I know replacing this drive will trash the spanned array requiring it to be rebuilt anyway so my rough and ready solution is: Delete the spanned partition Create individual partitions on each drive labelled E: F: G: and H: and work out which one is Harddisk3 Power down, remove each disk one at a time, power-up until the drive letter disappears But this seems a rather crude method of identifying the drive. The SATA connectors will be numbered on the motherboard but I appreciate this might not cross-match to what Windows calls them. Thanks, Rob.

  Read the article

• Solution for storing sata drives outside of case

  - by Jeffrey Kevin Pry

  I have a system that has 8 sata disks in a software raid 5 array using mdadm. My issue is that I want to move the drives from inside of the computer case in order to cool more efficiently. I have looked all over the web and only seem to find enclosures that hide the drives connectors behind an estata port or some other internal raid controller. Basically what I want is an enclosure or equivalent that I can run independent sata cables to and either power as well, or have it have its own power supply. I have the sata ports on the motherboard available and don't want to limit io by using one port with a multiplier or the like. One final caveat, I am a college student on a budget and don't have a fortune to spend on such an enclosure. Thanks in advance for your help and advice.

  Read the article

• Intel SASWT4I SAS/SATA Controller Question

  - by Joe Hopfgartner

  Hey there! I want to assemble a cheap storage sytem based on the Norco RPC-4020 Case. When searching for controllers I found this one: Intel® RAID Controller SASWT4I This is a quote form the Spec Sheet: Scalability. Supports up to 122 physical devices in SAS mode which is ideal for employing JBODs (Just a Bunch Of Disks) or up to 14 devices in RAID 0, 1, 1E/10E mode through direct connect device attachment or through expander backplane support. Does that mean I can attatch 14 SATA drives directly to the controller using SFF-8087 - 4x SATA breakout cables? That would be nice because then I can choose a mainboard that has 6 Onboard SATA and i can connect all 20 bays while only spending 155$ on the controller and like another 100$ on cables. Would that work? And why is it 14 and not 16 when there are 4 Ports? I am really confused about all the breakout/fanout/(edge-)expanding/multiplying/channel stuff...

  Read the article

• Dell eSATAp not working with some SATA disks

  - by pistache

  I have a Dell Inspiron XPS 15 (L502X) laptop, with an eSATAp port. I also have a Western Digital 1TB 3"5 SATA drive, that I'd like to use with the laptop. I bought a eSATAp <- SATA 22-pin cable (from Delock). When I use this cable my 3"5 HDD does NOT power up, no spin up. I thought that it's just this HDD taking too much power from the motherboard. However, I tested too with my 2"5 SATA HDD and it works successfully. Now the weird thing is that this 2"5 HDD takes 1.1A at 5V, and that the 3"5 HDD takes 0.7A at 5V. I don't understand why it can't work. Is there anything I could do for it to work ? What is really the problem ? Thanks for your help, Hugo

  Read the article

• Burnt SATA Drive

  - by luvieere

  By stupid curiosity, I've connected the FDD power cable to the jumper pins of a SATA drive, and powered on the system. The SATA drive's controller burned out. What now? Can it be replaced, and still be able to read the disc?

  Read the article

• sata cable with a clip

  - by RainDoctor

  What's the difference between a sata cable that does have a clip and one that does not have that clip? The cable with a clip: http://www.easy-computer-tech.com/images/sata-cable.jpg

  Read the article

• Broadcom HT1100 SATA controller not working properly with 1TB drives

  - by Jeff C

  I've been using RHEL distro's for several years and always managed to find the answers until now. I know this is more of a hardware issue, but I've been working on this for over a week and trust Linux and the IT community to help more then HP. I have CentOS 6.3 installed on an HP ProLiant DL145 G3 server with the BroadCom HT1100 IO controller and ServerWorks SATA Controller MMIO BIOS v3.0.0015.6 Firmware. This controller does not support large drives fully. Here's what I've tried and the results; Stock setup - Freezes on the ServerWorks POST screen. Can't even enter CMOS without disconnecting the drives. If I simply disconnect the SATA cables before it gets to the ServerWorks screen and reconnect afterwards I can boot from a CD, USB, PXE fine. However fiddling with cables at ever boot isn't practical. If I enter the BIOS config I can set it to not try booting the drives but leave the controller enabled. This lets me boot normally but the drives are not visible in the OS (live CDs or USB installed). I used method #2 to install and update CentOS. I have the /boot partition on a USB drive (everything else is on the SATA drives in software RAID1) hoping that would work around the issue but I get this Kernel panic - not syncing:Attempted to kill init! Pid: 1, comm: init Not tainted 2.6.32-279.9.1.el6.x86_6 #1 Call Trace: [<ffffffff814fd6ba>] ? panic+0xa0/0x168 [<ffffffff81070c22>] ? do_exit+0x862/0x870 [<ffffffff8117cdb5>] ? fput+0x25/0x30 [<ffffffff81070c88>] ? do_group_exit+0x58/0xd0 [<ffffffff81070d17>] ? sys_exit_group+0x17/0x20 [<ffffffff8100b0f2>] ? system_call_fastpath+0x16/0x1b panic occured, switching back to text console I'm sure it should be possible to talk to the drives without the BIOS boot check since the BIOS doesn't see them in method #2 either, their disconnected when it checks, but Linux sees them fine. If anyone could help figure out how I would greatly appreciate it! The other possible option I've come across is a complex firmware update. Tyan has a few boards on their website with the HT1100 and a ServerWorks v3.0.0015.7 update which says "adds support for TB drives" in the release notes. If someone could help me get the Tyan SATA firmware into the HP ROM file so I could just reflash that would also be very much appreciated. Thanks for any help you guys can offer!

  Read the article

• SATA drives or chipset throwing DRDY ERR and ICRC ABRT

  - by Matt

  I have an SD-VIA-1A2S PCI card with 2 sata ports (and one ATA-133 that isn't used). Two new Western Digital Caviar Green drives (WD10EARS 1TB) throw repeated errors in kern.log (removed date/time/host info for brevity): [ 7.376475] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1000500 action 0x6 [ 7.376480] ata2.00: BMDMA stat 0x5 [ 7.376483] ata2: SError: { UnrecovData Proto TrStaTrns } [ 7.376489] ata2.00: cmd c8/00:40:20:00:00/00:00:00:00:00/e0 tag 0 dma 32768 in [ 7.376490] res 51/84:2f:20:00:00/00:00:00:00:00/e0 Emask 0x12 (ATA bus error) [ 7.376493] ata2.00: status: { DRDY ERR } [ 7.376495] ata2.00: error: { ICRC ABRT } [ 7.376504] ata2: hard resetting link I'm using Ubuntu 9.04 - 2.6.28-18-generic, though I have tried live cds of Ubuntu 9.10, Fedora 12 and OpenSUSE 11.2 - all running various 2.6.31 kernels - and all received the same error. Based on testing these drives and this card in two other machines and combos of connecting the drives directly to the motherboard or the add-in card, I'm relatively convinced that it's the VIA chipset that is the problem. Another computer that also has an onboard VIA SATA chipset (like the add-in card) produces the same errors when the drives are directly on that motherboard. I have been able to verify that the drives are perfectly good, and I tried everything I can think of in terms of swapping cables, psu isn't overloaded, etc. The error happens on boot once or twice, after using fdisk on the drive once or twice, and constantly when attempting to sync a new mdadm raid 1 array created on the two drives. Any thoughts on where to go from here - driver/kernel wise? I'm completely open to buying a new PCI add-in card if someone can recommend one with 2 internal sata ports that works well in Debian/Ubuntu. Thanks!

  Read the article

• SATA Driver for Acer Aspire One D257

  - by Robert Niestroj

  i have a Acer Aspire One D257. In this netbook the hard disk is defect so i bought a new one. Now i want to reinstall Windows 7. Im using an external DVD Drive plugged into USB. The Windows 7 DVD is staring, Win7 setup is starting and when it comes to Hard Drive options it says that no drive was detected and i should try search for drivers. It shows me this window: Screenshot from web Now i cant find the right drivers for this netbook to continue with the installation. The laptop has the newest BIOS - 1.15, it is reset to factory default settings except that i enabled the Boot Menu prompt with F12. From the Acer Support Website i've downloaded the SATA AHCI Driver and the Chipset Driver. I unpacked both to a USB flashdrive in seperate folders. When i select the SATA AHCI Driver it does not find any drivers. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it shows one driver: Acer HWID (path_to\1.inf). When i continue with this driver i got an error message that says something like: No new devices found. Check if the driver files are on the installation disk. When i show him the Chipset Driver it sees a lot more driver. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it show some drivers: Intel N10 Family DMI Bridge Intel N10/ICH7 Family PCI Express Root Port Intel N10/ICH7 SMBUS Controller Intel N10/ICH7 Family USB Universal Host Controller Intel N10/ICH7 Family USB2 Enhanced Host Controller Intel N10/ICH7 Family Interface LPC Controller When i uncheck this checkbox i get a lot more drivers, and some SATA Drivers but the also do not work. I get the same error message as before. Can someone help me find a driver that should work or am i doing anything else wrong?

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• SATA drive problems with two SIL RAID cards

  - by Jon Topper

  I've just put a second SiI 3114 SATARaid card in my home server so that I could add another pair of SATA drives and increase my storage space. Annoyingly, it doesn't seem to work: [ 32.816030] ata5: lost interrupt (Status 0x0) [ 32.816072] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 32.816091] ata5.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 32.816094] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 32.816101] ata5.00: status: { DRDY } [ 32.816117] ata5: hard resetting link [ 33.136082] ata5: SATA link down (SStatus 0 SControl 0) [ 36.060940] irq 18: nobody cared (try booting with the "irqpoll" option) [ 36.060949] Pid: 0, comm: swapper Not tainted 2.6.31-20-generic #58-Ubuntu [ 36.060954] Call Trace: [ 36.060977] [] ? printk+0x18/0x1c [ 36.060997] [] __report_bad_irq+0x27/0x90 [ 36.061005] [] note_interrupt+0x150/0x190 [ 36.061011] [] handle_fasteoi_irq+0xac/0xd0 [ 36.061023] [] handle_irq+0x18/0x30 [ 36.061029] [] do_IRQ+0x47/0xc0 [ 36.061042] [] ? irq_exit+0x50/0x70 [ 36.061058] [] ? smp_apic_timer_interrupt+0x57/0x90 [ 36.061065] [] common_interrupt+0x30/0x40 [ 36.061075] [] ? native_safe_halt+0x5/0x10 [ 36.061082] [] default_idle+0x46/0xd0 [ 36.061088] [] cpu_idle+0x8c/0xd0 [ 36.061103] [] rest_init+0x55/0x60 [ 36.061111] [] start_kernel+0x2e6/0x2ec [ 36.061117] [] ? unknown_bootoption+0x0/0x19e [ 36.061133] [] i386_start_kernel+0x7c/0x83 [ 36.061137] handlers: [ 36.061139] [] (sil_interrupt+0x0/0xb0) [ 36.061151] Disabling IRQ #18 [ 38.136014] ata5: hard resetting link [ 38.456022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.456013] ata5: hard resetting link [ 43.776022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.776035] ata5.00: disabled [ 43.776055] ata5.00: device reported invalid CHS sector 0 [ 43.776074] sd 4:0:0:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 43.776082] sd 4:0:0:0: [sde] Sense Key : Aborted Command [current] [descriptor] [ 43.776092] Descriptor sense data with sense descriptors (in hex): [ 43.776097] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 43.776112] 00 00 00 00 [ 43.776118] sd 4:0:0:0: [sde] Add. Sense: No additional sense information [ 43.776127] end_request: I/O error, dev sde, sector 0 [ 43.776136] Buffer I/O error on device sde, logical block 0 [ 43.776170] ata5: EH complete [ 43.776187] ata5.00: detaching (SCSI 4:0:0:0) root@core:~# cat /proc/interrupts CPU0 0: 47 IO-APIC-edge timer 1: 8 IO-APIC-edge i8042 6: 3 IO-APIC-edge floppy 7: 0 IO-APIC-edge parport0 8: 0 IO-APIC-edge rtc0 9: 0 IO-APIC-fasteoi acpi 14: 53069 IO-APIC-edge pata_sis 15: 53004 IO-APIC-edge pata_sis 17: 112265 IO-APIC-fasteoi sata_sil 18: 200002 IO-APIC-fasteoi sata_sil, SiS SI7012 19: 111140 IO-APIC-fasteoi eth0 20: 0 IO-APIC-fasteoi ohci_hcd:usb2 21: 0 IO-APIC-fasteoi ohci_hcd:usb3 23: 0 IO-APIC-fasteoi ehci_hcd:usb1 NMI: 0 Non-maskable interrupts LOC: 6650492 Local timer interrupts SPU: 0 Spurious interrupts CNT: 0 Performance counter interrupts PND: 0 Performance pending work RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 160 Machine check polls ERR: 0 MIS: 0 root@core:~# lspci | grep Raid 00:09.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) root@core:~# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 9.10 Release: 9.10 Codename: karmic root@core:~# uname -a Linux core.topper.me.uk 2.6.31-20-generic #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC 2010 i686 GNU/Linux I've tried a combination of different kernel options (irqpoll, noapic, noacpi, pci=noapic) all to no avail. Does anyone have any bright ideas about how I can go about making this work? Swapping PCI cards around isn't an option as there are only two slots in this motherboard (an ASRock K7S41GX). The BIOS doesn't look to have too much in the way of configuration options regarding IRQ usage. Plan B is to ditch this server completely and buy a new QNAP for these drives to go in, but I was hoping to avoid doing this right now.

  Read the article

• ML 350 additional SATA RAID controller (mirror only)

  - by Nicholas

  I have a Proliant ML350 G8 with two SAS raid arrays currently set up - thereby maxing the default P420i raid controller. I need to set up a large video dump space in addition to this existing set-up (for non backed up, non-critical, temporary storage). I had planned to just add a 2TB SATA disk and plug it into the motherboard. However I it occurred to me the motherboard might have built-in mirror RAID support? Therefore I could use two SATA disks and have some semblance of redundancy. Is this possible? Or would I need to get a cheap raid card? Any recommendations?

  Read the article

• What type of SATA cable will I buy?

  - by Mehper C. Palavuzlar

  I've bought a new optical drive. It's a Samsung SH-S223C with SATA connection. Since it is OEM with no box, no cable came with it, so I need two cables now. Since I have an extra SATA power cable, it's OK, but I have to buy the data cable. What type of cable should I buy? If you please give a picture of it besides its type as well, I'll be happy. My motherboard is GigaByte P43-ES3G. TIA.

  Read the article

• SATA drive not recognized when installing RHEL 5.1 on PowerEdge R410

  - by Rachel

  Here's my setup: Dell R410 with Perc S100 (software) raid controller on an Intel ICH10R chipset The first problem is that the Perc S100 is only supported on windows. I'm trying to install RHEL 5.1. It boots from the cdrom, but later the installer can't see the cdrom or hard drive. Both are connected to the on-board sata controller. The only options in the R410 bios for SATA are ATA or RAID. I don't need raid, I just want a single drive setup.

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• SATA Devices not showing up when in UEFI mode

  - by Dan Barzilay

  I'm trying to install Windows and the bios should be set to UEFI mode. The problem is that all SATA devices aren't showing up (shows as if there aren't any) so I can't boot from the installation CD (it's just not there). The weird thing is that when set to LEGACY mode they all show up.. SATA mode is set to AHCI and I'm on Lenovo Y510P. I have a Linux OS installed that is accessible only when BIOS is in LEGACY mode (otherwise the hard drive it's on is not available) I also tried reseting the BIOS settings which didn't help.. Comment please if more details needed Extra details: Computer model: Lenovo IdeaPad Y510P (not overcloacked) Installed Linux OS version: Linux 3.7-trunk-amd64 x86_64 Trying to install Windows: Windows 7 Ultimate 64bit BIOS Information: Vendor: LENOVO Version: 74CN26WW(V1.07) Update: Using user1608638 answer and suggestion of using the USB flash drive as the boot device instead of the CD/DVD method I succeeded in installing Windows 7! (Thanks alot user1608638)

  Read the article

• ESXi onboard SATA passthrough [on hold]

  - by lodge93

  I am running ESXi 5.5 on a home system. When I attempt to pass one of the onboard SATA controllers (Intel ICH10R) to a VM, it is successful. However, the controller never appears in the VM. What else am I missing that would cause a VM to not recognize the controller? Additional Info: The controller is set to AHCI mode in the BIOS Prior to setting up the controller for passthrough, ESXi did recognize the controller and the drives I have tried with multiple VMs, none of which recognized the controller or the attached drives I have two onboard SATA controllers, on controller for ESXi and one for passthrough The final ideal state is that I could passthrough the controller to a FreeNAS VM

  Read the article

• How to arrange 2 SSD with 2 SATA?

  - by alfish

  I like to have best io performance as well as good capaciyy and reliability out of a server that hosts a busy forum, which involves loads of static files download. I am wondering what is the best plan to format and use the disks given that the server has only 4 disk bays and I have 2 SSD and 2 SATA disks at hand. I am currently thinking about putting the disks in RAID 10 so that SSD contains /var/lib/mysql as well as most of the OS (Likely to be Debian) and SATA disk to contain /path/to/static/files. However I'd like to hear your expert opinion on this. Thanks

  Read the article

• No SATA drives after PSU Upgrade

  - by hauptbenutzer

  I know this sounds a lot like this but I just confirmed that my MBR is fine as well as the SSD drive in question. What happened: I upgraded my be-quiet 700w PSU to the 1000w dark power pro. When I tried booting the system and none of the drives (all SATA) were detected, resulting in the "Boot device failure" error. After that I unplugged all but the boot drive, triple checked that all cables were in fact nice and tight inside their sockets, replaced both e-SATA and power cables ; still with the same outcome. Finally I reconnected my old PSU and sure enough the PC booted without any hassle (except of course for the direful construction that is currently occupying my desk). Does anybody have any advice on how to proceed? Surely, it is possible the PSU is faulty but are there other explanations? Thanks in advance PS. if of any help: Motherboard is GIGABYTE GA-PH67A-UD3-B3 H67 LGA 1155

  Read the article

• Computer won't start when connecting SATA HDD

  - by vlad

  I just bough a new HDD some time ago and recently i bought another SATA cable to have both HDDs connected at the same time, to transfer all the files from the older one to the newer. When i connected both of them, the computer started working, i tapped F2 to go to bios to make sure it was detected, and then after 5-10 seconds the computer instantly shut down. After this incident, my computer won't start at all when connecting the SATA power supply to the old HDD. If i connect only my new drive, it works without any problem. If i connect only my old drive, or both the old drive and the new one, and then push on the power button, the cpu fan simply rotates about 5 degrees and then stops.. and that's it, the computer doesn't start, and no sound from the pc speaker either. Is there any way to recover my files from the old HDD and transfer them to my new one? I do not want to use the old HDD any more, i only need to save all my files.

  Read the article

• SATA hard disk for laptop on Desktop PC

  - by Lawliet

  I know that this forum is for programming-related questions only, but I'm having this dilemma so here I go. Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) Thanks in advance

  Read the article

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• How to move partition with Users to a new SATA controller?

  - by Al Kepp

  Our current situation: X79 chipset. Windows 7 installed on SATA SSD running on Marvell controller. C:\Users contains just Public and computer-name folders, all the other users are created in E:\Users. That partition is on two HDD's running on an Intel RAID controller. (The motherboard has got two SATA/RAID onboard controllers.) The goal is: Without reinstallation, I want to move SSD to a standard SATA controller. Then I want to get rid of RAID1, and move one HDD to the same internal Intel SATA controller and the current E:\Users move to that new place. I want it to stay as E:\users, but I need to reinstall the HDD to let it work in SATA mode without RAID. So I face several problems. I am sure all are solvable with free software utilities, but I don't know how exactly to do it. I can see the particular problems: I have got all users at E:\Users. When I turn off that E:\ disk, I won't be able to login to Windows. I need at least one admin account to be placed back at C:\users. The current C: runs on standard 120 GB SSD, but it is connected to a Marvell SATA/RAID controller. I am affraid the Windows won't let me put it to Intel SATA controller due to hardware/licence check, and I won't be able to use standard W7 recovery disk either, because there probably isn't marvel SATA/RAID driver on it. I haven't tried anything yet, because I am affraid I can end up with computer not working at all. (I want to move it to a standard ICH10 Intel SATA controller to let us have no problems in future with it. I think it is not very safe when we use any nonstandard hardware to boot the computer.) I need to somehow backup current E:\ disk and restore it to a new E:. I hope this will be the easy part (as long as the admin account will reside on C:). The E: RAID array is very large, but it is almost empty (less than 100 GB of data.) So I can make the partition smaller so it can easily fit to a single SATA HDD.

  Read the article

• How does plugging in a SATA drive to an SAS backplane affect maximum cable length?

  - by user179658

  The limit on SATA cable length is 1m, whereas the limit on SAS cable length is 10m. When using a backplane which advertises support for SAS and SATA, with a SAS RAID controller and one SATA drive, will the controller use the SAS PHY scheme, allowing for the 10m cable length maximum (to accommodate the long backplane), or will it use the SATA one and allow for only the SATA cable length maximum of 1m?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >