Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 301/370 | < Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >

• Setting a Static IP Running FreeBSD8 in VirtualBox hosted on Windows 7

  - by gvkv

  I'm using VirtualBox on Windows 7 (host) to run a FreeBSD (guest) based web server. I`ve assigned a static ip of 192.168.80. 1 to the (virtualized) NIC which is run in bridged mode. The problem is that when I ping an external server (such as google.com) I get a No route to host error: dimetro# ping google.com PING google.com (66.249.90.104): 56 data bytes ping: sendto: No route to host ... I can ping the BSD server from both another virtualized machine and my host machine and from the server, I can ping everything on the network. The router ip is 192.168.1.1/16. ADDENDUM: I have the following lines in /etc/rc.conf on the BSD VM to configure networking: defaultrouter="192.168.1.1" ifconfig_em0="inet 192.168.80.1 netmask 255.255.0.0"

  Read the article

• The canonical "blocking BitTorrent" question

  - by Aphex5

  How can one block, or severely slow down, BitTorrent and similar peer-to-peer (P2P) services on one's small home/office network? In searching Server Fault I wasn't able to find a question that served as a rallying point for the best technical ideas on this. The existing questions are all about specific situations, and the dominant answers are social/legal in nature. Those are valid approaches, but a purely technical discussion would be useful to a lot of people, I suspect. Let's assume that you don't have access to the machines on the network. With encryption use increasing in P2P traffic, it seems like stateful packet inspection is becoming a less workable solution. One idea that seems to make sense to me is simply throttling down heavy users by IP, regardless of what they're sending or receiving -- but it doesn't seem many routers support that functionality at the moment. What's your preferred method to throttle P2P/BitTorrent traffic? My apologies if this is a dupe.

  Read the article

• VPS for Glassfish

  - by Harry Pham

  Our small startup company plan to deploy a web application on Glassfish, I and wonder if some of the experience user out there can answer me couple question. When I shopping for server, I usually look at RAM amount, as GF does required good amount of RAM to run, below are the two sites with significant price different for the same amount of RAM. I wonder why?? Godaddy: http://www.godaddy.com/hosting/virtual-dedicated-servers.aspx?ci=9013 Versus http://entic.net/Servers Does below plan from Godaddy consider good to run GF application. OS: Linux CentOS • RAM: 4 GB • Storage: 60 GB • Bandwidth: 2,000 GB/mo Our web application is a social network, expected to have 2000-4000 users to start with

  Read the article

• Installing Sharepoint 2007 on Windows Server 2008 R2

  - by ronischuetz

  we are using in our lab a clean installation of Windows Server 2008 R2 which is running as Hyper-V instance. Today we wanted to install a clean installation of Sharepoint 2007 with SP1 on this machine and we explorer an error that we are not able to install it. The setup is comes up with an error which is described here: http://support.microsoft.com/kb/962935 but this is not our szenario. A printscreen of this message can be found here: http://www.ronischuetz.com/images/SP_2007SP1_Inst_Error.png @Microsoft, my personal point of view is that it cannot be that we need to install first 2008, then Sharepoint 2007 with SP1, then SP2 and upgrade to 2008 R2. Nobody is going be happy with this solution and I hope we find a fast way how customers can install Sharepoint direclty on 2008 R2. Anyway, thanks in advance for any further information how we should go on with this issue. The issue is listed here: http://social.msdn.microsoft.com/Forums/en-US/sharepointadmin/thread/91a6be50-9009-43c8-a37c-66cfb83d738f

  Read the article

• Is a matching entry in /etc/hosts required for hostname?

  - by JohnWoltman

  I was installing a Tomcat webapp that refused to work until I stumbled on someone else's issue with an unrelated product. The solution was to add the machine's name to /etc/hosts, to match the name returned by hostname. Is this required for general Linux networking to function correctly? My webapp is running in a virtual machine so that I can test the webapp, and I don't normally bother with the /etc/hosts file on VMs. I just shook my fist and cursed Tomcat and webapp's behavior. I read http://serverfault.com/questions/118823, but that doesn't say if it's required or not.

  Read the article

• Group policy to disable notifications of particular errors?

  - by resolver101

  How do i disable the notifications of particular errors? A little background to my issue. During the installation of the Kaspersky, it disables all the windows firewall for all except the domain. I have remedied this by creating an offline policy in Kaspersky which enables the Kaspersky firewall when out of the office (ie not connected to the office network). The problem now is that users in the office now see a notification showing that the firewall is disabled even though it’s enabled in all scenarios. It’s just that work and home show as disabled when the clients are connected to the office LAN. I’ve looked into the notifications and you can disable the notification (not recommended) but I don’t want to do this incase other relevant messages are stopped from being displayed. http://blogs.technet.com/b/networking/archive/2010/12/16/disabling-firewall-alerts-in-the-action-center.aspx

  Read the article

• Secure copying (file transfer) between two Linux servers in the same datacenter (Linode)

  - by MountainX

  I have two Linodes in the same data center. I want to copy files from one to the other each night or on demand (for about the next month, until this project is finished). So I'm thinking about using rsync. My question is how do I set up the two Linode servers to communicate via private IP addresses securely? Both servers are SSH hardened, they use denyhosts and have a fairly restrictive iptables setup. I know I need to first assign private IP addresses to each server, then configure static networking according to this guide. What is next? What SSH or iptables settings are needed to allow these two servers to communicate? What further info do I need to supply in this question? I'm looking for a basic step-by-step guide for how to do this.

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• What is the best free service to host images and mp3 files?

  - by Edward Tanguay

  I am making an educational social software silverlight application. I would like users to be able to point the application to a URL with text, images, and audio files which they have created. Many users will not have their own website to do this, so we are looking for a free service they can use to upload, and manage their own text/image/audio content. What is the best free service for non-technical users to upload and make available text, images and audio? For instance, sites.google.com allows you to upload pictures and access them via http so that would work, but that is more about making a website. For this purpose we just need the ability to upload files, without the website creation tools.

  Read the article

• Nagios: Which services should I monitor on different roles of servers?

  - by Itai Ganot

  I've started working in a new workplace and my first task is to build a Nagios server and configure it to monitor the servers in the network. Since I'm starting from scratch I wanted to hear from you, experienced users, which checks should I configure for each role? For example, there are some basic checks which I run on each Linux machine I monitor: SSH, Ping, Load, Current Users, Swap Usage, etc... Now my question is, which specific checks should I run for a DataBase server, for a Networking Switch, for Httpd servers? (I currently monitor how many httpd processes are running) Thanks in advance

  Read the article

• Win2008 - restrict VPN user permissions

  - by Sebas

  Windows 2008 R2 SP1 Foundations file server with no AD, only workgroup sharing some folders, and now a RRAS server. Shared folders are open to everyone in the office (XPs and Sevens) without accounts/passwords, but I was thinking about partially limiting access to the new "VPNuser" account. I'm new to Windows Server and its permissions settings: I thought about denying access to vpnuser through NTFS rights in some folders. It doesn't work, but now I'm guessing that the vpnuser is not considered as a logged user (doesn't appear as such) and is considered a "guest", like the rest of people connecting in the office. I say that because of this: http://social.technet.microsoft.com/Forums/windowsserver/en-US/ff6d3726-ff41-4d3f-9d97-5361af0206dd/vpn-users-on-server-shows-as-guest?forum=winserverNIS Also, because when I create a txt file using the VPN connection, owner field shows in description as "guest". Am I right? How can I set different rights for the VPNuser from the rest of "guest" users in the office?

  Read the article

• FoxPro 2.6 DOS on Windows 7 64-bit

  - by Rolando

  I support a company that has a very old, mission critical, FoxPro for DOS 2.6 (FPD) application. For variuos reasons the company didn't adapt/migrate their app, which, ironically, has been running even better under Windows XP (and 32-bit Win7) because the OS allowed new features like more reliable networking, distributed printing, email integration. Unfortunately for this company, most new machines now come with a 64-bit version of Windows 7, which is incompatible with their FPD app. I know this time the writing is on the wall: the only long-term solution is to migrate their app. But I wonder if anyone can suggest a temporary alternative path, which doesn't involve either: downgrade 64-bit Windows to 32-bit, or run the app on a virtualized 32-bit XP

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• Computer never connects to the internet automatically on startup?

  - by RawR Crew

  I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

  Read the article

• Sharing VPN from XP to Linux virtual

  - by user55513

  Hi I will keep the question simple with few details, if more is needed tell me. Thanks. I am playing around with networking and virtualbox. So I have 2 virtual machines. One is windows xp and another has linux in it. Windows XP has 2 network cards. One for the internet and the other to connect to the linux computer. Linux has one 1 card and it can only access the internet passing through Windows XP. Internet works fine until I activate OpenVPN on Windows. When I turn on VPN, Linux has no access to it. How can I make linux use VPN too? I believe it has something to do with using the "route" command on XP to send VPN traffic to Linux but I was not able to figure it out how yet.

  Read the article

• Setting up Debian squirrelmail

  - by Muazam

  I'm new to networking. I need to set up a email server and I also need to create an email address. ex. [email protected] I've installed squirrelmail and dovecot. http://www.mydomain.com/squirrelmail/src/login.php Shows a log in screen, but when I try to log in I get this error: Error connecting to IMAP server: 127.0.0.1. 111 : Connection refused I have no experience with squirrelmail and dovecote. Anyone can help me out, I really appreciate it. Thanks!

  Read the article

• Apache does not serve non-locally

  - by yodaj007

  I have a freshly installed instance of Fedora Core 16 inside VirtualBox using bridged networking. On it, as root I typed in: yum -y install httpd service httpd start ifconfig Inside the VM, I can open a web browser to 'localhost' and I get the Apache test page. It works. But in Windows (the machine hosting the VM), I point my browser to the IP address returned by ifconfig (192.168.2.122). The connection times out. I can go to a command prompt and ping the VM. Is there a firewall or something that comes with Fedora by default? Or is there something I need to change in a config file?

  Read the article

• How difficult will it be to switch DHCP from Windows 2000 to our network router?

  - by MetalSearGolid

  While I know a bit about networking, I am more of a programmer, and I have never set up a DHCP server. I have always allowed a router to assign IP addresses. However, my boss has asked me to switch out our old Win2k Domain Controller and DHCP server to a new server. The catch is that he wants to just use our router to assign IP addresses rather than have the new server do it. Is this going to be more than just disconnecting the old server? And if so, are there any documents or tips anyone can help me to make the transition a bit smoother? The new server will most likely have Windows Server 2008 R2. Any advice I can get on this matter would be greatly appreciated.

  Read the article

• Virtualizing Firewalls/UTM

  - by TheD

  So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

  Read the article

• Connect macbook to my LAN through a VPN - best solution?

  - by LewisMc

  So I have a LAN connected via a ADSL/PPPoA, this is using a bog-standard DLink router supplied by my ISP (talktalk UK). I have a NAS within the LAN that is running FreeNAS and I want to be able to connect to it when I'm out and about. It's running an atom so it's quite low on juice consumption but I don't want to have it on all day and night so I've been waking it via a magic packet and booting it down from the web admin when I need it. So I want to connect to the LAN, I presume via a VPN, to be able to send a magic packet. But what is the best method to accomplish this, or is there an easier way? I've been looking at the cisco 857 integrated router and the Netgear prosafe 318(behind modem) but not sure If I'm on the right track with what I want to achieve as I've not much experience or knowledge with VPN's or networking (software engineering student). I have tried port forwarding but to no avail, either with magic packets or even connecting outside the LAN via DYNDNS. Thanks,

  Read the article

• Sorting IPv4 Addresses

  - by Kumba

  So I've run into a quandary on sorting IPv4 addresses, and didn't know if there was a set rule in some obscure networking document. Do I do a straight sort on the raw address only (such as converting the IP address to a 32bit number and then sorting), do I factor in the CIDR via some mathematical formula, do I sort via the CIDR only (as if I'm comparing the network size and not the addresses directly)? I.e., normal math, we'd do something like -1 < 0 < 1 to denote the order of precedence. Given say, 10.1.0.0/16, 172.16.0.0/12, 192.168.1.0/24, and 192.168.1.42, what would be the order of precedence?

  Read the article

• how to debug mysql has gone?

  - by fefe

  I have a virtual machine(Ubuntu 12.04, MySQL 5.5) running under VMware and is dedicated to host a mysql server. I connect to this server on internal IP. I'm trying to find out why I get mysql server has gone error. One my windows machines apache it stops because of this issue. I have been trying to fine tune my mysql my.cnf with the following parameters but did not bring the desired result. # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 0.0.0.0 # # * Fine Tuning # wait_timeout = 180 key_buffer = 384M max_allowed_packet = 64M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 500 table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M how to debug this issue what is missing from configuration to avoid this error?

  Read the article

• Can I increase the link speed of the RAS Server on our MS Win2k3 box?

  - by Ducain

  We are running a Win2K3 Server box, and I'm a remote employee that connects via VPN. I've been frustrated for some time by the connection speed over the VPN (the office HQ has a decent speed and I have a biz class connection here), and decided to do some checking today. This morning, I was dialed in and looked at the networking tab of the task manager, and I see that the adapter for the RAS Server (the box has 4 Gigabit adapters) has a speed that seems far too low. The speed for the RAS Server link hovers between 300 - 600 Kbps. The local connection (and others) all say 1 Gbps. Can I set this to a higher speed? Is this information accurate? Thanks for the input.

  Read the article

• Debian crashed, file system is read-only and cannot backup - How Do I find/mount a USB drive?

  - by Spiros

  We have a Debian server (vm's) here at work and the server crashed after a power failure. I can only boot the system in maintenance mode, and the whole file system is set to read only. I can run fsck though maintenance mode, however I would like to get a backup of some files before I do. Problem: I cannot access the net since there is no network connectivity in maintenance mode, and for some reason I try to add a USB flash drive to the computer but I can't find it through the console. Question: how to you find/mount a usb drive on Debian? I have tried several resources from the internet but nothing worked. Is there any other way I could get a backup of my files? I cannot start networking since the filesystem is set to read only. Any help would be appreciated.

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

< Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >