Search Results

Search found 21317 results on 853 pages for 'address bar'.

Page 306/853 | < Previous Page | 302 303 304 305 306 307 308 309 310 311 312 313  | Next Page >

• Remotedesktop to windows 2008 server with 2 nics

  - by The_Mo

  Hi I have 2 NICs on a Windows 2008 R2 Server. nic1 with ip address 192.168.2.1 with gatewaty 192.168.2.254 and nic2 with ip address 10.96.6.253 with no gateway. The windows 2008 server is connected to a router which is connnected to another router so if I want to connect to the windows 2008 server I use 192.168.0.31 because it is forwarded. If I use remote desktop to connect to that machine I use 192.168.0.31 and that works well, but the server has a seccond nic and I want to be able to connect with a remotedesktop to nic2. Any help appreciated! [server windows 2008 r2 192.168.2.1] -- [router 192.168.2.254/192.168.0.31] -- [my computer 192.168.0.13 gateway 192.168.0.254]

  Read the article

• Can I create a virtual network interface to connect to a real network device?

  - by michelemarcon

  I have a networked windows pc with 2 network interfaces. The first connects to a lan with ip address 10.1.. The second connects to another lan with ip address 10.2.. Maybe it's a dumb question, however is it possible to virtualize the second network interface, so that the pc can connect to the 2 lans? If necessary, I may switch to linux or paravirtualization. CLARIFICATION: I want to send DHCP broadcast packets on the second lan, but not on the first lan. I want to do it with one single physical network interface. At the moment, I'm not using any virtualization software.

  Read the article

• nslookup gives wrong ip for my domain

  - by Werulz

  I am having some problem in trying to setup DNS for my domain on my server. This tutorial normally works fine for me but when i tried to lookup my domain it gives the following output Server: 4.2.2.1 Address: 4.2.2.1#53 Non-authoritative answer: 119.100.79.64.in-addr.arpa name = server.leech4ever.com. Authoritative answers can be found from: The server and the address are wrong according to the tutorial Here is tutorial http://webcache.googleusercontent.com/search?q=cache:rR7Z4YU4GI0J:www.broexperts.com/2012/03/linux-dns-bind-configuration-on-centos-6-2/+broexperts+bind&cd=1&hl=en&ct=clnk&gl=mu /etc/hosts 127.0.0.1 localhost 64.79.100.119 server.leech4ever.com server /etc/resolve.conf search leech4ever.com nameserver 64.79.100.119 /etc/resolv.conf nameserver 4.2.2.1 nameserver 4.2.2.2 How to solve this problem guys.....The tutorial was flawless until i did a server restore

  Read the article

• vmware player - ubuntu can resolve hostname but ping fails

  - by recursive_acronym

  Using VMware players on Windows 7 with a Ubuntu 10.04 guest. When I ping it resolves the ip address but the ping fails. Hopefully this is a local issue as I don't have access to any of the network equipment (routers, etc). vmware tools is installed. Is there any other information I can provide to help resolve this? eth0 Link encap:Ethernet HWaddr 00:0c:29:83:4f:c0 inet addr:192.168.163.129 Bcast:192.168.163.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe83:4fc0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:50006 (50.0 KB) TX bytes:16701 (16.7 KB) Interrupt:19 Base address:0x2024 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)

  Read the article

• Setup IPv6 over IPv4 tunnel in VPN

  - by bfmeb

  Let me explain my szenario: I have a linux server A. A is reachable in a VPN. So if I am connected to the VPN over Internet I can successfully ping A. Server A is connected to a Router B. Router B has a local ipv6 address and there are resources (each of them with a local ipv6 address) connected to Router B. After I am connected to VPN, I am able to use ssh to have access over A. Now I can use the ping6 command to ping the Router B or one of its connected resources. This works fine. The ping fails if I try to ping router B on my computer. Overview: My Computer -- VPN -- Server A(ipv4) -- Router B(ipv6) -- Ressource A(ipv6) On resource A runs for example a HTTP-Server. My question is: How can I access Resource A (for example with HTTP) on my to VPN connected computer? Is it possible? Should I setup a tunnel device? Sorry for this inexpertly explanation, but I am new to network stuff!

  Read the article

• How-To: Run CMSDK against a RAC cluster

  - by frank.closheim

  Using CMSDK in a production environment often requires a robust, reliable and failover enabled repository. When using Oracle Real Application Cluster (RAC) with your CMSDK repository you need to have a specific configuration in place to support such a setup. This post will explain the configuration steps required when running CMSDK 9.0.4.6 with Oracle WebLogic Server (WLS).In the previous CMSDK 9.0.4.2 version a RAC enabled connect string looked like this: (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = rac1)(PORT = 1521))(ADDRESS = (PROTOCOL = TCP)(HOST = rac2)(PORT = 1521))(LOAD_BALANCE = NO)(FAILOVER = ON)(CONNECT_DATA =(SERVICE_NAME = rac)(failover_mode = (type=select)(method=basic)))CMSDK 9.0.4.6 makes use of data sources to connect to the underlying database. These data sources are configured inside your Application Server, such as Oracle WebLogic Server.In Oracle WebLogic Server 10.3.4, a single data source implementation has been introduced to support an RAC cluster. It responds to Fast Application Notification (FAN) events to provide Fast Connection Failover (FCF), Runtime Connection Load-Balancing (RCLB), and RAC instance graceful shutdown. XA affinity is supported at the global transaction Id level. The new feature is called WebLogic Active GridLink for RAC; which is implemented as the GridLink data source within WebLogic Server.This GridLink data source also works with Oracle Single Client Access Name (SCAN). SCAN is a feature used in RAC environments that provides a single name for clients to access any Oracle Database running in a cluster. You can think of SCAN as a cluster alias for databases in the cluster. The benefit is that the client’s connect information does not need to change if you add or remove nodes or databases in the cluster.The CMSDK 9.0.4.6 documentation describes how to create a regular JDBC data source named jdbc/OracleDS. Please refer to the following document which describes in detail how to create a GridLink data source in WLS.

  Read the article

• How do I bridge my wireless to my wired connection?

  - by gatoatigrado

  I want to bridge the wireless connection with the wired connection. The wireless is the host and the wired is the client, so to speak. Internet sharing (inet <--> wifi <--> ethernet) I tried to bridge my ethernet connection by going to network manager edit connections wired edit IPv4 settings shared to other computers Screenshots However, it seems to automatically disconnect half a second after it says "connection established"! edit 2 got the network manager logs, it seems the address is in use. See http://pastebin.com/DjqRshxW , line 45. nm-tool output is here: http://pastebin.com/x5Aci5V1 . I tried firestarter, as mentioned in another thread, and no luck. I don't have time to bother with a dozen command line tricks, unless is copy & pasting a shell script... so please suggest ways that use GUIs and/or won't leave my computer in a confused state (e.g. disabling network manager, manually connecting to a WPA network, installing brutils, etc.). edit: one idea that would work, if it's possible -- is there a way to share connections via SSH and SOCKS5? I'd need to do this at a system-wide level though; I only know how to do it through the browser now. Then, I could run ifconfig eth0 192.168.4.1 on the computer sharing the inet, and ifconfig eth0 192.168.4.2 on the computer I'm trying to share with; I know this does work for host-to-host transfers. edit 3 If I run sudo killall dnsmasq, then nothing is using the 10.42.43.1 address the network manager sharing wants to use. But now it just takes longer to die, with error "NetworkManager[5935]: dnsmasq died with signal 9" [ http://pastebin.com/4FNtpugi ]. Looking at just the commands [ http://pastebin.com/1vrtQeWk ], maybe it's trying to route eth0 to itself? I'm not that familiar with networking things though.

  Read the article

• Remote access to a KVM Ubuntu virtual server

  - by Lee

  I've just setup an ubuntu virtual server and everything seems to be working fine. I used KVM to get it working with a bridged network. I've given the virtual server a static ip address on my network. I don't seem to be able to connect to the virtual machine though from outside my network. If I'm on my own network it all works fine, I can ping the ip and connect to it. The virtual server can ping other machines and sites on the internet. I changed the port forwarding rules on my router to forward any connections on a specific port to the virtual server ip address thinking that was the problem, but it was still the same. Is there something I'm missing here which is blocking outside connections to the virtual machine? Thanks.

  Read the article

• How to do port forwarding in D-link Glb802c?

  - by Manish

  I have some questions about port forwarding on my D-Link Router GLB-802C. For example: My local machine's IP is 117.1.1.81 My router's IP is 117.1.1.1 My Public (Web) IP is 117.16.1.1 My questions are: What will be my Global Address 'To'? What will be my Global Address 'From'? In Destination Port "From" and "To" what do I select in the drop down list and port no for forwarding HTTP traffic (for my website)? In Local Port, what do I select in drop down list and port no?

  Read the article

• Branding/Restricting a Software by License/Serial

  - by Sid

  I have made a POS System for a client of mine using MS Access Server-Client approach. He asked me to brand his software to allow only a certain "number" of users (cashiers) to access the POS System, and must be determined to the license his client will buy. EX: 10 User License = 10 Cashiers ( not necessarily 10 users, it can be 30 users, shifting) = it means 10 PCs will be installed with the client software I made. How and where do I put the logic that will determine if it is licensed or not. What I have done: I have created a serial key generator using Name. Problem is it can be duplicated once you give than name+serial combination, it would still work. I am counting the number of users logged at a time. This could be problematic as I am using MSAccess and not MSSQL. I have scrapped this idea, He also asked me if I could just put serial+mac address combination. That I could do but he will have a hard time implementing it and selling it if he needs the mac address of every computers to be installed with my POS. I am at lost on what can I do. Would like to ask for tips and suggestions. Thank you.

  Read the article

• external hard drive not detected after ubuntu crash [restarting machine]

  - by Netmoon

  today i tried to watch movie [with vlc media player] from my external hard drive [expansion portable 500 GB], and it's play good, then pause the movie and play it again, and my Ubuntu crashed! [Ubuntu 12.04]i had to restart the machine, so did it, but after that Ubuntu can't recognize this hard drive! i changed USB cable but it was not effective. this is my dmesg command result : [ 191.281630] usb 2-1.3: new full-speed USB device number 9 using ehci_hcd [ 191.353527] usb 2-1.3: device descriptor read/64, error -32 [ 191.529115] usb 2-1.3: device descriptor read/64, error -32 [ 191.704669] usb 2-1.3: new full-speed USB device number 10 using ehci_hcd [ 191.776524] usb 2-1.3: device descriptor read/64, error -32 [ 191.952202] usb 2-1.3: device descriptor read/64, error -32 [ 192.127772] usb 2-1.3: new full-speed USB device number 11 using ehci_hcd [ 192.534742] usb 2-1.3: device not accepting address 11, error -32 [ 192.606749] usb 2-1.3: new full-speed USB device number 12 using ehci_hcd [ 193.013696] usb 2-1.3: device not accepting address 12, error -32 [ 193.013906] hub 2-1:1.0: unable to enumerate USB device on port 3 note: I am able to hear the sound of the external drive lens. When attach hard drive to usb port, the status light goes on, but it's low bright and i think its power is low! try to mount in Microsoft Windows 7, but nothing happened.

  Read the article

• Cannot access shares via \\servername but \\ip works

  - by Jeff

  To set up the scenario: One of our techs set one of the domain controllers to use Microsoft time. The time IS correct (including Time Zone) and DOES match the other domain controller's time; it was previously incorrect, however. Since the change, no users can connect via \\servername\share or \\servername.domainname.com but \\ip\share works fine. I cannot even access it from the other domain controller with which I know both have the same time. The servername DOES resolve to the correct IP address. Also, strangely enough, \\domainname.com works as well which resolves to the same server. Finally Everything that I have tried does resolve to the same, correct IP address. The error is: login failure: The target account name is incorrect. I believe it is time related but since the times are correct and match I'm not sure. Anyone know what might cause this?

  Read the article

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• HP DV6 connects but no internet

  - by Frank Barcenas

  I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

  Read the article

• How do I PXE Boot Only when I want it to without user intervention?

  - by troz123

  I would like to setup a PXE environment where I can re-image machines remotely without any user intervention. Only problem is when the re-imaging is completed it will do the re-imaging again and again and again. If I remove the MAC address file then I just get a error saying it can't find the MAC address file and the system stops. I also tried turning off the TFTP server and I get a error stating can't find TFTPD server. How can I make client machines only PXE boot once and after the re-imaging it will boot into Windows and everything is happy? And only PXE boot when I want it too... I'm using TFTPD32 to serve the files. I'm using a Windows 2003 DHCP server that points to pxelinux.0...

  Read the article

• EDQ Technical Enablement for OPN (Prague - June 17-19)

  - by milomir.vojvodic

  Oracle Enterprise Data Quality (EDQ) Technical Enablement and Partner Training Trusted Data for Your Enterprise Applications Oracle Enterprise Data Quality helps organizations achieve maximum value from their business-critical applications by delivering fit-for-purpose data. These products also enable individuals and collaborative teams to quickly and easily identify and resolve any problems in underlying data. With Oracle Enterprise Data Quality, customers can identify new opportunities, improve operational efficiency, and more efficiently comply with industry or governmental regulation. Oracle Enterprise Data Quality is designed to serve as a very channel friendly platform to OPN.  This means that pre-built extensions, components and even complete business solutions can readily be built and shared.  This allows our customers/partners to be highly efficient in how they deploy custom business solutions, but also allows our partners to develop specialized components, domain knowledge and even complete business solutions. Training is suitable for: · Database administrators · Architects · Technical staff Objectives of the training: After completing this course, participants should: · Have an understanding of the core functionality of EDQ across profiling, auditing, transforming, parsing and matching data · Be able to describe some of the key capabilities and benefits delivered by EDQ · Be able to create and run standalone EDQ processes and jobs · Be ready to start working with data from customers and (with practice) be able to demonstrate EDQ to customers Agenda 17th June Fundamentals For Demoing (Profile, Audit, Transform and More) Profiling Auditing Transforming Writing and exporting data Jobs and scheduling Publishing, packaging and copying EDQ processes Introduction to the Customer Data Extension Pack Realtime Processing via Web Services The Server Console Run Profiles Data Interfaces Sampling Publishing metrics to the Dashboard Users and security 18th June Matching Matching overview Basic matching configuration Matching rule hierarchies Clustering Merging Reviewing possible matches Outputting Match Data Case study 19th June Address Verification Address Verification Overview Configuration Accuracy Flags Parsing Parsing Overview Phrase profiling Tailoring a CDEP Parser Base Tokenization Classification Reclassification Selection Resolution Register Here Don’t miss this FREE event. Space is limited. Oracle University V Parku 2294/4 148 00 Praha 4 17.6. – 19.6. 2014 09:00 a.m.– 17:30 p.m.

  Read the article

• Fresh Apache install can't be connected to

  - by Wayne M

  I've got to be missing something here. I have a brand new CentOS server with a LAMP install on it. My domain host (GoDaddy) has the server's IP address configured as the "A Record". Since the server will host subdomains I have enabled NameVirtualHost and set up a virtual host pointing to the web app on the server. I haven't touched anything else in Apache, and it's listening on Port 80 like it should be. However, I can't connect to the server either by DNS or by IP address. I've set up several servers exactly like this one and never run into this before. What could be causing this? Did someone on the host set up a firewall or something that blocks port 80? As I said, I can't connect to the server via anything, but it's a barebones box with LAMP installed on it.

  Read the article

• Remote Access to Owncloud Server

  - by John

  I'm currently trying to setup my own own-cloud server, and I've got it fully installed, configured, and accessible from within my own local network. I cannot figure out how to access it from the outside. So far I've: Successfully setup port-forwarding on my local router. I've done so via 'single port forwarding' and 'port range forwarding' Ports 80, 443, 3306 (Apache-Full and MySQL) Successfully obtained my external IP address. I've also tested this magic number from within the network at #insertIPhere/owncloud and it did work. Successfully setup the server using SQLite Successfully setup the server using MySQL Created the following exceptions in my firewall: Allow In Port 80 (Apache Full) Allow In Port 443 (Apache Full) Allow In Port 3306 (MySQL) Tried connecting from several different remote networks, as to troubleshoot something on their end As far as trying to access it, I'm doing so through Google-Chrome and Mozilla Firefox trying to reach the server through #insertIPhere/owncloud using the above public IP address. So what have I missed, and how do I access my server from outside? Thanks in advance for your help and time, and I apologize in advance for what will probably result in my noobish mistake in networking. I've looked at the official documentation. And also this question here.

  Read the article

• Connecting to my SMTP server

  - by Joseph Silvashy

  I have a few questions, I just installed SMTP on my Ubuntu server, and I want to know how to connect to it from a different machine... I'm not really clear. I tried: telnet my.servers.ip.address 25 I think it's running on port 25, but I don't know where to find out, its not in the conf file anywhere. Additionally do I need it to be a FDQN? or can I just access my mail server via it's IP address? I know that the service works on the machine because I'm able to echo test | mail -s "test" [email protected] Any help debugging or understanding this would be helpful, thanks guys!

  Read the article

• How to convince non-programmer his notions about computers are wrong?

  - by Suma

  Recently I came across a question about 64b on SuperUser for which the accepted answer seemed like a complete nonsense to me. I made two comments pointing out obvious mistakes. To my perplexion, the comments had an effect of the poster of the answer being alienated. I have no idea how could I convince him he is wrong, as he does not seem to understand the basics of the problem. He seems to be mixing concepts like bus size and address size - see the pearl sentence "it will allow you to address all of your RAM because your processor is reading from your RAM in 64 bit words.". The poster asks me to provide proves of my claim by quoting a respectable source, but I have no idea where to find such source, as I doubt anything I would consider relevant would be relevant for him (it would be probably too technical). I think this instance can serve as an illustration of communication problems between programmers and users (and to certain extent even to any expert vs. non-expert communication). How should a programmer handle a communication like this, so that is does not become a useless quarrel?

  Read the article

• Unable to use autossh in background even with absolute path

  - by Zagorax

  I would love to set autossh to run at boot adding it to /etc/rc.local. This command works: autossh -i /root/.ssh/id_rsa -R 2522:localhost:22 user@address But, if I add the -f option autossh -f -i /root/.ssh/id_rsa -R 2522:localhost:22 user@address The ssh session is not started. As you can see, I'm using an absolute path for my identity file, so this seems to be a different problem from the one stated here: autossh in background does not work From /var/log/syslog: Oct 18 11:08:39 raspberrypi autossh[2417]: starting ssh (count 1) Oct 18 11:08:39 raspberrypi autossh[2417]: ssh child pid is 2418 Oct 18 11:08:39 raspberrypi autossh[2417]: ssh exited with status 0; autossh exiting I'm using it with debian wheezy on a raspberry pi, autossh version 1.4c. Could it be that it's passing the -f option to ssh instead?

  Read the article

• how can I force automatic filling to be enabled on webpages?

  - by thepaulpage

  I'm using the Chrome Browser. I enjoy the "automatic filling" that it uses to fill in things like my address when I'm shopping online. Sometimes I get a message that says: "This webpage has disabled automatic filling for this form" Is there a way that I can tell Chrome to ignore what the webpage wants and just give me what I want? I'm not talking about passwords, I'm talking about Chrome's automatic filling in of things like my email address, zip code, etc. For Example: https://www.kansas.gov/ump/register/account?

  Read the article

• How to embed word doc as background picture of an Access report using .EMF or equivalent ?

  - by iDevlop

  My company's standard paper has logo, address and all the details in the right margin with a vertical blue line. I have that as a word template. I want to have the same thing as the background of my Invoices report. I managed to do that 5 years ago by saving to EMF format (vector format, prints out nicely) and putting the file as the background of the report. Now my company is moving, and I need to change the address on my invoices, but I can't find out how I did to convert the word doc to EMF. Any suggestion ? By EMF or another process, but I want to avoid BMP, which is huge and does not print nicely. Thanks !

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Gnome-Shell Logout

  - by Nerdfest

  The latest version of Gnome-shell starts to display (the top bar appears briefly) but I then get logged out. This happens when I start it with "gnome-shell --replace". Any idea how to make it behave properly? Laptop is a MSI U21, an0d I run with a 'nomodeset' startup option. Without this option the screen clears to just wallpaper and stays that way. Gnome-shell v2.31.5 Kernel 2.6.35-27 (& 28 as well)

  Read the article

< Previous Page | 302 303 304 305 306 307 308 309 310 311 312 313  | Next Page >