Search Results

Search found 9456 results on 379 pages for 'controller'.

Page 308/379 | < Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >

• DNS Does Not Register at Off-site Locations

  - by Russ Warren

  First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

  Read the article

• Kerberos service on win2k dc will not start following disk failure

  - by iwilson68

  Hi, I have a win2k (mixed mode domain) with 4 DCS. One of these also acts an exchange 2000 server which uses 2 logical volumes from an MSA 2000 array. AD etc is stored on local drives. We experienced a problem last week when the raid array fell back to a redundant controller and this temporarily meant that the two logical drives were not visible to the server for around 5 minutes and a couple of reboots. The log records these Events as Type: Warning Event Source: Disk Event Category: None Event ID: 51 Date: 06/11/2009 Time: 11:46:23 User: N/A Computer: server1 Description: An error was detected on device \Device\Harddisk1\DR1 during a paging operation. Following these problems, the server “kerberos Key Distribution” service refuses to start with an “error.31 a device attached to the system is not functioning”. All other automatic start services (including net logon) are running and there are no DNS issues etc. All devices are also functioning but the two logical MSA disks are now numbered in the Windows Disk Management MMC as 2 and 4 and I suspect that they may have previously been identified as disks 1 & 2 and perhaps windows still sees this as an ongoing failure?? Replication has not been affected but obviously there are many audit failures in the security log relating to users and workstations presumably linked to the Kerberos issue. Attempting to manually start the kerberos service generates the following in the System Log. Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 09/11/2009 Time: 09:46:55 User: N/A Computer: Server1 Description: The Kerberos Key Distribution Center service terminated with the following error: A device attached to the system is not functioning. DCDIAG passes all tests except “Advertising” and “Services” which I believe relate directly to the failure of Kerberos only. Any advice would be appreciated.

  Read the article

• 403 Forbidden when Deploying asp.net 4.0 site to IIS 7

  - by Jordan

  So I have an EC2 instance running, the URL NoWeatherSurprises.com I have the DNS pointing there, and I set up a new site in IIS 7 and pointed it to a folder. I used Visual Studios Web Developer 2010 express to publish to this folder. It now has the binaries and such. However if I go to NoWeatherSurprises.com I get the welcome to IIS 7 screen. I'd expect to go to my application If I navigate to http://noweathersurprises.com/weather/ [weather was the folder I published to under wwwroot] I get a 403 forbidden. I have no idea why, I am guessing that it is trying to do a directory listing or something instead of launching my MVC Application. So 2 problems in summary. It is not pointing the domain to the folder directly and I need to add /weather I am getting a 403 forbidden instead of the results of my home controller with the index action. I am new to IIS 7, I had been using IIS 6 and had a lot less trouble setting it up, but I suspect that's my own fault and i am just missing something. Thanks in advance for any help

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• Ubuntu xrandr rotate issue

  - by user83544

  I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

  Read the article

• Picking a linux compatible motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• Something very strange with network

  - by Rodnower

  Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

  Read the article

• Setup.exe called from a batch file crashes with error 0x0000006

  - by Alex

  We're going to be installing some new software on pretty much all of our computers and I'm trying to setup a GPO to do it. We're running a Windows Server 2008 R2 domain controller and all of our machines are Windows 7. The GPO calls the following script which sits on a network share on our file server. The script it self calls an executable that sits on another network share on another server. The executable will imediatelly crash with an error 0x0000006. The event log just says this: Windows cannot access the file for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Setup.exe because of this error. Here's the script (which is stored on \\WIN2K8R2-F-01\Remote Applications): @ECHO OFF IF DEFINED ProgramFiles(x86) ( ECHO DEBUG: 64-bit platform SET _path="C:\Program Files (x86)\Canam" ) ELSE ( ECHO DEBUG: 32-bit platform SET _path="C:\Program Files\Canam" ) IF NOT EXIST %_path% ( ECHO DEBUG: Folder does not exist PUSHD \\WIN2K8R2-PSA-01\PSA Data\Client START "" "Setup.exe" "/q" POPD ) ELSE ( ECHO DEBUG: Folder exists ) Running the script manually as administrator also results in the same error. Setting up a shortcut with the same target and parameters works perfectly. Manually calling the executable also works. Not sure if it matters, but the installer is based on dotNETInstaller. I don't know what version though. I'd appreciate any suggestions on fixing this. Thanks in advance! UPDATE I highly doubt this matters, but the network share that the script is hosted in is a shared drive, while the network share the script references for the executable is a shared folder. Also, both shares have Domain Computers listed with full access for the sharing and security tabs. And PUSHD works without wrapping the path in quotes.

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• LSI MegaRAID LINUX got Optimal after degradation but strange POST message

  - by kesrut

  Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

  Read the article

• New router messed up server 2003 setup...

  - by Aceth

  Hey, We were sent a new 2wire router today configured it as best we can to match the old bt voyager. We've also got X static IP's. We've manage to get our webserver on one of the new IP's public facing. then we use a hardware firewall which is in a DMZ again with a different static IP. This firewall then is our gateway for our internal LAN. with a few servers etc. The problem we're having is only our PDC (primary Domain controller which has exchange 2003 on) can't ping externally even an external IP. We've connected laptops to the 2wire router and obtain a private ip 192.168.1.X and it works fine can ping etc. our other servers with an internal ip behind the firewall can ping out fine. We've connected to the firewalls logging console and the pings from the server are allowed through so its fine there. The server in question is a Windows server 2003 R2 Enterprise SP2 + Exchange 2003 Server doesn't have firewall turned on. it has static private IP .. gateway is pointing to the right one External Static IP is routing fine inwards We've ran out of ideas .. help??

  Read the article

• Windows Server 2003 SBS domain in multiple sites

  - by E3 Group

  We have about 25 employees in our current office and are looking to open up another office in another capital city housing about 15 employees. In our current office, we are running a domain hosted by a 2003 SBS server and I've been tasked by the boss to expand our infrastructure to the new office in the cheapest way possible (cheapest way in the short run that is, because my boss doesn't think more than 6 months ahead). So I'm looking to get a second hand server and have it run Server 2003 Std with exchange server 2003. These are the things that it needs to do: Replicate shared folders that are hosted in the parent LAN. Deliver emails hosted in the parent Exchange Server Somehow link up with the parent domain controller and push the AD to the remote site I'm pretty sure 3 is impossible but the DC would be available if a VPN connection is present, right? On that note, would I be looking at hardware VPN connections? I'm not sure how to deploy the new site as this is my first time doing it and i'm making it especially difficult for myself, seeing as the AD and DC is on an SBS server. Would I first start by establishing a VPN connection and then joining the new server to the domain? Will things 'just work' if I install exchange onto the new server and point outlooks to it? and how would I be able to replicate shared folders?

  Read the article

• Are SATA II and SATA 3.0 Gbps compatible?

  - by Johnny Maelstrom

  I am trying to check that if I buy a new internal HDD it will work in the NAS I am buying. Currently I'm confused about naming schemes and once that is resolved whether there is compatibility. I will gladly author this question to be more general if there is not already an article helping with the confusion of SATA naming and standards. I see similar, but not identical questions and will accept this as a duplicate if thought as such. The specifications on the eCommerce site for the NAS says, "Controller Interface Type Serial ATA-150", the product home page for the manufacturer says, "Compatible with SATA and SATA II HDD". The specifications on the eCommerce site for the hard drives say, "Interface Type Serial ATA-300", the product home page for the manufacturer says, "Interface SATA 3.0 Gbps" Wikipedia says many things about different naming conventions, the closest being, "SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them." Are SATA II and SATA 3.0 Gbps the same? I feel I'm tantalisingly close to getting a definitive answer here before I purchase, but really want to clear up these naming schemes.

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• VPN Error 691 but server says authenticated on server

  - by Andy

  Hello all, I have a problem with a vpn connection on Windows XP SP3 that appears to be related to an account (maybe privilleges or an option that I have missed). When connecting using my account, which is a domain administrator account it will connect to through the vpn fine. However, using an account created for another person they receive Error 691: Username or Password is not valid for this domain. On the domain controller (windows 2003) I see a logon successful message: User DOMAIN\user was granted access. Fully-Qualified-User-Name = int.company.net.au/People/Management/User NAS-IP-Address = 10.30.0.3 NAS-Identifier = not present Client-Friendly-Name = MelbourneCore Client-IP-Address = Router-ip Calling-Station-Identifier = not present NAS-Port-Type = Virtual NAS-Port = 77 Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = undetermined Policy-Name = Remote VPN Access Authentication-Type = MS-CHAPv1 EAP-Type = Does anyone have any ideas as to where else I should look for finding a solution? If i use the wrong password it gives a logon failure error in the event viewer. Also removing them from the remote access group gives a logon failure error. Nothing appears in the event viewer on the local machine. In the past all that is required is to add them into our Remote Access Users group. Any help?

  Read the article

• How to use Python to read the physical address(MAC ID) [closed]

  - by getjoefree

  I want to read the physical address of the NIC model, i can get the results that i want to with SED.EXE before, but SED.EXE does not support my environment but Python ok, who have the means to do it. The general situation (not plug the network cable, it is impossible to obtain IP address): Ethernet adapter: Connection-specific DNS Suffix.: Chianet Description ...........: Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller Physical Address .........: A4-BA-DB-9D-1E-8E Dhcp Enabled ...........: Yes Autoconfiguration Enabled ....: Yes Ethernet adapter 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1510 Wireless-N WLAN Mini-Card Physical Address. . . . . . . . . : 00-23-4D-D9-C0-28 The description of the NIC different, we can use this to fetch the corresponding physical address, base on Physical Address does not work, because the computer with the WLAN Card, I want to use Python to read my computer the card information and after Python handles an output file, output file format: SET MAC = A4BADB9D1E8E and sed format: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" > WINMAC.BAT getmac.sed: /Marvell Yukon 88E8040/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; }

  Read the article

• Laptop will not boot

  - by WillumMaguire

  This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

  Read the article

• EFI vs MBR - Installing Windows Server 2008 R2 or 2012 on 8TB

  - by Riaan de Lange

  I'm having some difficulty installing Windows Server 2008 R2 and Windows Server 2012 on an Intel Server platform. The server specs is as follows: Intel Grizzly Pass Server System - R2308GZ4GC 2x Intel Xeon 2620 - 2.0 GHZ - BX80621E52620 132 GB of Memory REG-DIMM - TS1GKR72V6H 4x Seagate Constellation ES 2TB 3.5" 7200rpm 6GB/S - ST32000645NS Intel Big Laurel 4CH 6G SAS RAID 512MB - RS2BL040 On the Intel RAID Controller Setup, I have setup the HDD to be in RAID-0 - for testing purposes. (Ultimately configured in RAID-5) So, the total size of HDD space I can use is 7.6 TB something... When I install the Server OS's, they don't seem to go beyond 2 TB (1.76 TB) I have read up on EFI and UEFI boot, and this seems to work in 2012, but I could not install any drivers for the motherboard... So, I also tried EFI for 2008R2, and this worked while installing the OS, it did not however work with the Windows Boot Manager option in the BIOS. It kept on freezing once it tries to load the partition. My idea was to allocate the complete 8 TB for the OS, and load a few VM's on there. I have now started with a new approach where I'll have a 256 GB OS Partition, and a secondary 7.5 TB Data partition. Oh, and I also did a diskpart - convert disk to gpt whilst installing 2008R2. The whole disk was accessible, 7.6TB Can anyone please clarify that EFI/UEFI is meant for larger boot volumes? Bigger than 2TB. If I were to have an ideal situation where my OS is run on a SSD, 256GB, and I can attach the 8 TB drives as normal disk to the OS? I'm I correct in saying that if I wanted to boot from a 8TB partition, I would need to force the BIOS to boot from EFI? The limit for MBR is 2 TB as far as I know now... *FYI: The motherboard is EFI-ready

  Read the article

• Under which circumstances can a *local* user account access a remote SQL Server with a trusted connection?

  - by Heinzi

  One of our customers has the following configuration: On the domain controller, there's an SQL Server. On his PC (WinXP), he logs on with LocalPC\LocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It works. In SSMS, the connection shows up with the user Domain\Administrator. Firstly, I was surprised that this even works. (My first suspicion was that there is a user with the same name and password in the domain, but there is no user LocalUser in the domain.) Then we tried to reproduce the same behaviour on his new PC, but failed: On his new PC (Win7), he logs on with OtherLocalPC\OtherLocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It fails with the error message Login failed for user ''. The user is not associated with a trusted SQL Server connection. Hence my question: Under which conditions can a non-domain user access a remote SQL Server using Windows Authentication with different credentials? Apparently, it's possible (it works on his old PC), but why? And how can I reproduce it?

  Read the article

• Hard drives (SATA/ATA) corrupting

  - by JC Denton

  Hello All, 2 years ago I bought relatives a new computer for christmas and installed Ubuntu on it. Ever since then it has been experiencing problems with the hard drives. The hard drive supplied with the machine was a SATA drive. When it appeared it was having problems (files and folders with invalid encoding started appearing) I replaced the SATA drive with the drive of their previous computer. I replaced it (The replacement) later on, the drive being rather old and thus becoming more prone to the risk of failure. The replacement drive is a IDE drive but the same problems started to appear (files and folders showing up in nautilus with invalid encoding). I fear the files and folders that are showing are existing FS entries, starting to corrupt. As it's happening to both the IDE and SATA drive it's unlikely to be the drives themselves or the IDE/SATA controller, I believe. Any ideas as to what could be causing the (assumed) corruption? EDIT: You're right about the paragraphs. They were there in edit mode but I'm still getting to grips with the whitespace format codes. The system is a "Primo Pro" AMD Phenom II X4 Quad Core 920 2.80GHz SILENT DDR2, ordered from overclockers.co.uk and nothing has been added to it except for the replacement of the SATA drive with an AMD drive. It would seem unlikely for a barebones system to be underpowered.

  Read the article

• Cannot resolve Hostname to IP, but IP to hostname works

  - by dotnetdev

  I have deployed a bunch of windows server VMs on a cloud hosting service. These machines are all joined to a domain controller on the same service, which also hosts DNS. All of the domain-joined machines have dynamic IP (along with the DC). If I try to resolve any of the hostnames remotely, it fails. For example, I am in SQL Server Reporting Services and I need to connect to a remote server. I provide the hostname of the desired target server and this fails, but then if I provide the IP, this works. How can I pass the hostname and have this resolve to IP? Is there anything I need to look for in the DNS server? It has records of the hostnames (in forward lookup I think), but reverse is empty. Isn't it the case that forward lookup resolves ip to hostname and reverse resolves hostname to ip? Also, I don't know what he subnet mask because this is not in my control, so the machines may not be in the same subnet - can this be a cause of the problem? Where is the problem? Thanks

  Read the article

• Setting up Red Hat Enterprise Linux Server as a mail exchange server

  - by Syedur

  I am a Unix/Linux/Windows Server noob. So, keep that in mind before you throw your stones at my glass house. :P I have a Windows Server 2008 R2 machine that's acting as domain controller, Server A. It's also running a DNS server. I have a Red Hat Enterprise Linux Server 5.3, Server B that is intended for mail server. In order for the mail delivery to happen, I understand that I have to set an MX record on Server A and point it to Server B. Well, I did. I manually added a host name on Server A and pointed to Server B's IP address. Then I added an MX record and pointed it to the host name. That didn't do the trick. After taking the above steps, I used the "dig" command on Server B to lookup the MX record coming back from Server A and it wasn't what I was expecting. What am I doing wrong here? I have noticed that... my Windows machines that are joined to the domain (Server A) are listed under the host names. The machines that are not joined to the domain are not list. This is fine, I am not worried about this. What does concern me, do I have to join the Server B to domain in order for Server A to recognize as a valid host and forward the MX properly? If so, some simple steps on how to join Server B to the domain would also help.

  Read the article

• Very poor SCSI hd performance on IBM x336 with LSI 1030 RAID1

  - by David Tschoepe

  I'm experiencing very poor performance on an IBM x336 server with dual 73GB 15k hard drives on a U320 controller, LSI 1030. We're getting maybe 3.5MB/sec max (per HD Tune utility). It should be over 100MB/sec at least, I would think (another x335 box is running 70-80MB/sec). The server was recently setup and didn't really notice the problem, but may have been there from the beginning, so not sure. I have installed the IBM ServerRAID Windows utility. The server is running Windows 2008 R2 Web edition (if that matters). I thought maybe one of the drives was bad, so far I have removed one of the drives out of the array and tested again, but still the same results. I'm waiting for the RAID1 to resync and I will try pulling the other drive next. I've also used the ServerRAID utility but haven't noticed anything in there that might indicate a problem. Not sure if I'm on the right path here. So looking for some advice to track this down.

  Read the article

• Possible DNS issue after a reinstall of Windows Server 2000 (get off my lawn)

  - by cop1152

  I just replaced a drive on a Win2000 Server that replicates AD and issues out DHCP at one of our offices. I successfully joined it to the domain, setup range of IP's, etc, but am still having issues. I cannot RDC to it with name or IP. I can ping it, browse to it with Windows Explorer, and remote to it with some other software, but not RDC. The other issue is this: Users are unable to authenticate on it. They receive the message 'username or password incorrect' (or something like that). Changes made on the main domain controller seem to take forever to trickle down. The most significant entry in the DNS Server Log is Event ID 7062: The DNS Server Encountered a Packet Addressed to Itself. At least, I think its significant. The Directory Services Log shows numerous Event IDs 1265: The attempt to establish a replication link with parameters failed with the following status: The DSA operation is unable to proceed because of a DNS lookup failure. Does this make any sense to anyone? I feel like its something very simple that I am overlooking. Thanks in advance.

  Read the article

• Can't set screen brightness in Gentoo system

  - by Real Yang

  My system: Linux gentoo 3.10.7-gentoo-r1 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 240M] (rev a2) output of xbacklight: No outputs have backlight property output of xrandr: xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1280 x 720, maximum 1280 x 768 default connected 1280x720+0+0 0mm x 0mm 1280x720 0.0* 1024x768 61.0 800x600 61.0 640x480 60.0 1280x768 0.0 output of ls /proc/acpi: button/ event When I'm in kernel 3.8.13, I can change my brightness using xbacklight. I compiled 3.10.7-r1 using genkernel all. Before the upgrade I did get a notice of "compatible issues for Nvdia users" from emerge but I still don't know the details. It there anyway to let me set the brightness? Then i found a ebuild app-laptop/nvdiabl-0.81 and tried to emerege nvidabl, I got this message: Your kernel does not support FB_BACKLIGHT. To enable you it you can enable any frame buffer with backlight control or nouveau. Note that you cannot use FB_NVIDIA with nvidia's proprietary driver Please check to make sure these options are set correctly. Failure to do so may cause unexpected problems. Once you have satisfied these options, please try merging this package again. ERROR: app-laptop/nvidiabl-0.81::gentoo failed (pretend phase): Incorrect kernel configuration options Call stack: ebuild.sh, line 93: Called pkg_pretend nvidiabl-0.81.ebuild, line 31: Called linux-mod_pkg_setup linux-mod.eclass, line 559: Called linux-info_pkg_setup linux-info.eclass, line 911: Called check_extra_config linux-info.eclass, line 805: Called die The specific snippet of code: die "Incorrect kernel configuration options" [SOLVED] I enter the menuconfig again and check the Device Drivers -> Graphics support -> Support for frame buffer devices, then i found this: <*> nVidia Framebuffer Support [*] Support for backlight control (NEW) What can i say. Recompiling...

  Read the article

< Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >