Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 308/455 | < Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >

  • What you'd need to setup BBS?

    - by raspi
    What I need to setup BBS nowadays? I'm thinking of BBBS or PCBoard (no telnet! too new technology). What I've thinked so far, I'd need: virtual machine which runs DOS and hook that virtual COM-port to somekind of virtual VoIP modem software somehow (is there any?). How you can call to it across internet? Can you use HyperTerminal straight with that virtual/real modem? Or will VoIP just garble the modem data and nothing will work?

    Read the article

  • ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

    - by frank
    Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

    Read the article

  • What caused Cyclic Redundancy Check error on my BitLocker-enabled external hard drive and how to fix it?

    - by Forgiver
    I have an external hard drive that is connected to my computer (Windows 7 Ultimate 64 bit) via a USB port. BitLocker has been activated on the hard drive to protect the data. Yesterday I started downloading a huge data from the internet but now it failed to complete because of CRC error. I tried to repair it with chkdsk f:/r where f is the drive letter of that hard drive. There are many messages reporting "unreadable" as follows: What caused Cyclic Redundancy Check error on my BitLocker-enabled external hard drive and how to fix it?

    Read the article

  • so i installed sql server now how do i connect to it?

    - by letseatlunch
    SO i have a server running windows server 2008 r2 and i just installed Microsoft sql server 2008. I used the manager thing to create the database and the tables, etc and now i want to connect to it via my visual studio which is on a different machine. so how do i do that? do i need to "turn on" the sql server, do i need to do port forwarding? do i have to modify the iis or change those settings? is there a good article someone can me point me to? just to further help you help me, i understand how to connect to a datasource in visual studio my problem is more with the sql server and understanding how to properly set it up once installed. Sorry for the noob question, i got it all installed and i know how to use it once its all going i just don't know the in-between. thanks in advance dave

    Read the article

  • I would like to have a publicly accessable linux box hosted elsewhere. Who provides this service?

    - by Eric Wilson
    I would like to have a general purpose linux server available and publicly accessible. I understand that there are no lack of web-hosting companies, but I might want more control over the machine than is typical. I would want the ability to install software, such as an SVN server, and I would like to be able to expose various port numbers, as I may have a variety of extremely low traffic sites that I would want to have available. Obviously, one option is to host such a machine in my home. Is that my only option? Or is what I describe out there, possible as a virtual machine on a larger server?

    Read the article

  • How can I create a pen drive that I can boot from, and then install Win98 from?

    - by rossmcm
    I have a HP Compaq t5515 thin client computer with a flash disk and USB port. I want to put Win98 onto it, replacing whatever is on there now (I think it is some Linux-based thing). I can find stuff about putting Win98 onto a pen drive and running from that, but I can't find any info about installing Windows 98 from a pen drive onto a sep[arate system. Is it just a matter of making the pen drive bootable to DOS copying the contents of a Win98 installation CD onto the pen drive booting the HP machine from the pen drive running SETUP.EXE from the pen drive? Any pointers appreciated. TIA

    Read the article

  • OpenVPN Permission Denied Error

    - by LordCover
    I am setting OpenVPN up, and I'm in the state of adding users. Details: Host System: Windows Server 2003 32-bit. Guest System: Ubuntu Linux (with OpenVPN installed already), actually I downloaded it from OpenVPN.Net. Virtualization: VMWare v7.0 Problem: I can access the Access Server web portal (on the port 5480), but when I login to http://host_ip:943/admin and enter my (correct) login info, it shows me a page saying that "You don't have enough permissions". I am the (root) user!!!! that is really weird!!! Note: if I enter wrong login it will denote an incorrect login, this means that I am logging in successfully but the problem comes after the login process. What I tried: I tried to create another user after (root) logging in to Linux Bash using (useradd) command, but the same resulted.

    Read the article

  • Wamp virtualhost with supporting of remote access

    - by Farid
    To cut the long story short, I've setup a Wamp server with local virtual host for domain like sample.dev, now I've bind my static IP and port 80 to my Apache and asked the client to make some changes in his hosts file and add x.x.x.x sample.dev , I've also configured my httpd virtual host like this : <VirtualHost *:80> ServerAlias sample.dev DocumentRoot 'webroot_directory' </VirtualHost> Client can reach to my web server using the direct access by ip address, but when he tries using the sample domain looks like he gets in to some infinite loop. The firewall is off too. What would be the problem?! Thanks.

    Read the article

  • Windows vista firewall exceptions unchangeable

    - by user61099
    Hey, I want to allow a program (iTunes) through my windows firewall, so i check it in the program or port list under the exceptions tab (in my windows firewall settings), then i click OK. When i reopen the window the box is unchecked again. Which means i can never get the program through my windows firewall. I think this is a problem due to administrators rights. Because I also can not delete the program from the list. I can however delete other programs from the list. Anybody have any ideas, tips, remarks?

    Read the article

  • setup advanced filtering and access restrictions on dd-wrt using iptables

    - by Nova deViator
    I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

    Read the article

  • Empty sshd_config file

    - by Thomas
    I run a Centos 5 server with a LAMP stack. I was told this morning that the server was down not serving web content. I then tried to restart httpd but it failed due to another process was listening on port 443. I checked what process was running on 443 using netstat and it was sshd. I then checked the sshd_config file to check the ports that sshd was running on but the sshd_config file was completely blank. I than ran chkrootkit and it flagged not suspicions. What could of caused the sshd_config file to be blank, and sshd service to be restarted? I would really value your thoughts. All the best.

    Read the article

  • Want 2 external monitors with a 13' MacBook - is this possible?

    - by kevinburke
    I've got a 13' white MacBook from 2008 and I'd like to run one or two external monitors, my budget is $500. I've tried to do research and this is what I was going to get - will these work OK? Two Diamond BVU195 HD USB Display Adapters (DVI and VGA with included DVI to VGA adapter) to plug into the USB port Two Dell ST2310 monitors One external USB hub so I don't use up both of my USB ports Will this work? I've read some people say it does and some people say it doesn't, but I don't know enough to say either way. Also do you have recommendations for a better monitor than the dell sd2310? what's the best setup I can buy for $500? Thanks very much for your help, Kevin

    Read the article

  • How do I configure Shrewsoft's VPN client to only route traffic to a certain IP address through the VPN?

    - by dommer
    We're using Shrewsoft's VPN client to connect to a third party development server. However, it seems to be configured to send all or nothing through the VPN. The devs have to disconnect from the VPN to get email/internet access back. The server that needs to be accessed via the VPN is on a specific (local - 10.x.x.x) IP address and a specific ports. Can we configure the Shrewsoft client application to only route traffic to that one address and/or port through the VPN and to route anything else though the usual channels? If so, how is it done? I'm not a VPN specialist and the options are confusing. In the absence of any Shewsoft VPN client specific advice, what should I be search for? Split tunnels?

    Read the article

  • Why are my USB 2.0 devices hanging Windows XP?

    - by BenAlabaster
    Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors - it has a NEC uPD720102 chipset. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine? Edit: Updated the USB 2.0 info with reference to actual card - http://www.xpcgear.com/lpnec4u.html

    Read the article

  • Setting up dovecot on OpenBSD

    - by Jonas Byström
    I'm a *nix n00b that just installed dovecot (the selection with no ldap, mysql or pgsql) on OpenBSD 4.0 and I want to set it up for imap use, but I'm having a hard time finding documentation that I can understand. It currently running on port 143 (checked with telnet) but from there I need to do the following: I need some accounts, the once already on the system are fine if I can get those running (seemed to be some dovecot option somehow?), or just adding a few manually is ok too. Was there some setting for this in the default /etc/dovecot.conf? passdb bsdauth {} is uncommented by default... I need to create imap folders, or subfolders. How can I do that? Hopefully not, but anything else I need to do? I want to run without certification validation and no SSL/TLS, would this work by default (client-side settings)?

    Read the article

  • Production Instance : CLOSE_WAIT Connection Issue

    - by rajnikant
    I am using 10EC2 Instances behind 1 ELB. And ELB configured 80 to 8080 and 443 to 8080 port. And all 10EC2 instances having installed with Apache Tomcat, total request on ELB around 8000 to 10000 in 1 minute. I am facing problem for CLOSE_WAIT connection on 10 EC2 Instance, having Apache Tomcat. EC2 Instance Type : m1.xlarge When we restart the Apache Tomcat, all CLOSE_WAIT connections are lost, but its not proper way to work on Production Instances. Please help me out.

    Read the article

  • Changing Internet connection on ISA Server 2000

    - by garyb32234234
    Hi We are getting a new internet connection installed and will need to unplug the old one and connect this to our ISA Server 2000. Will this be a simple swap out job? We will be given a new ip, which i know i will have to enter into the external network card TCP/IP page. I will also be given the default gateway to enter. The ISP engineer said we may have to reset the ARP? cache, if we dont know how we will have to reset the ISA server? Has anyone any experience? The current connection is with the same ISP but it was owned by the business park were we are located and they linked up an ethernet port to what i assume is their own router. Hope you can help, i know that ISA 2000 is somewhat less easy to use than the newer versions.

    Read the article

  • Scrolling mouse sets windows sound volume

    - by Ikke
    Suddenly, when I use the scroll wheel of my mouse, it changes the windows sound volume level. I have a HP DV6-2030SD laptop with Windows 7 64 bit and a Zolid p50622 mouse. When I use the scroll function of the mouse pad of the laptop, it does not adjust the sound level. I don't have any special mouse drivers installed, just the standard windows drivers. When I scroll, I see the HP sound level screen: It doesn't do it always, but when it does, it prevents the current window to scroll, which is really annoying. Rebooting doesn't help. I've tried to put the USB dongle in a different port, but this doesn't help either. Any advise on how I can fix this?

    Read the article

  • Could a computer act (dependably) as a wireless router for 200+ clients? [closed]

    - by awkwardusername
    That is, I have a Core 2 Duo E7500 at 2.93GHz, with 2GB memory. I plan to install either Windows Server 2012 or Zeroshell 2.0RC1, and it also (planning to) includes two PCIe Wireless Card Adapters. It also has one ethernet port, and I will connect that to another machine which will be a Database and a Web Server. My plan is to have a corporate level wireless intranet with 200+ clients. I cannot afford to buy routers because I want to operate at zero costs as possible, utilizing my available resources. Is that plan plausible? Also, what minimum specs should my wireless card have? @SvenW: Oh, I meant corporate on the deployment level. I am still an undergraduate and this is more of an educational and expiremental work than an actual project. I got Windows Server 2012 for free though, and this isn't actually for commercial use.

    Read the article

  • lighttpd silently stops logging

    - by Max Cantor
    I'm on a Slicehost 256MB VPS with Ubuntu 9.04 (Jaunty). lighttpd is the only web server process running; it listens on port 80. My lighttpd.conf can be found here. I'm using Ubuntu's default logrotate setup for lighty. At seemingly random times, lighttpd will stop logging. It is not correlated with log rotation--that is, the errors do not occur when logrotate kicks in. What happens is, I will verify that the server is serving files by hitting a URL with my browser, and I will verify that it is not logging by checking access.log and seeing that the GET request I just made is not there. Using init.d to restart the process starts logging again, without truncating or rotating the log file. That is, new requests will be logged at the end of the existing access.log file. There are no cron jobs running on this box. Any ideas?

    Read the article

  • ASA firewalls: how does stateful filtering affect my access lists?

    - by Nate
    Ok, so assume that I have an ingress access list that looks like this: access-list outside_in extended ip permit any X.Y.Z.1 eq 25 access-group outside_in in interface outside And I want to do egress filtering. I want to allow inside machines to respond on port 80, and I want to allow ports over 1024. Given that the firewall is statefull, do I need to have the rule access-list inside_in extended ip permit X.Y.Z.1 any eq 25 in my inside_in ACL, or can I get away with just access-list inside_in extended ip permit any any gt 1024 access-group inside_in in interface inside In other words, if I apply an egress access list, do I have to explicitly allow machines to respond to requests allowed by the ingress access list, or does the statefullness of the firewall handle that for me? Thanks!

    Read the article

  • Steps to make sure network is not blacklisted...Again

    - by msindle
    I have an interesting issue. I have a client that just got blacklisted due to spam being sent out over the last 2 days. I have my firewall configured to only allow mail to go outbound on port 25 from our mail server (Exchange 2010) exclusively and I have verified that there are no open relay's on our transport rules. We are running Vipre Business and after running deep scans with updated definitions all computers come back clean. I ran a message tracking report on our Exchange server that shows all mail sent via the mail server over the last couple of weeks and didn't see anything malicious or out of the ordinary. I have also verified that there are no home devices or rouge computers on the network. For all practical purposes it appears that the network is clean, but we still wound up on 5 or 6 blacklists...Where should I start looking next? Is there a "best practices" guide that can help eradicate this issue? Thanks in advance! msindle

    Read the article

  • Sony Bravia (KDL-32EX402) audio connection fails

    - by Rasmus
    Hey. I'm having trouble connecting my computers audio to the TV (Sony Bravia KDL-32EX402). I'm using a standard AUX cable (some kind of adapter for L/R to go into the headphone plug on the computer). I'm connecting the other end to the back of the TV, it doesn't actually say "AUDIO IN" but it has to be (is also right below the "HDMI 1 AUDIO IN). When changing to "PC-mode" and setting the audio input to "PC" nothing happens. (but the pictures get's transmitted fine by VGA). I have checked that it's not the PC's headphone port, nor the AUX cable. What to do, what to do ?

    Read the article

  • Recommended SMTP Relay Service [closed]

    - by Ryan
    I've got a legacy application that needs an smtp server to relay emails. Each client has various control over their IT infrastructures (from little to none at all), so I can't necessarily install an smtp server on each of their machines. Can anyone recommend a basic SMTP Relay Service? Its literally only for sending a couple of emails a day to a list of about 20 users per client. The application only allows for the smtp server and to/from addresses to be specified. I'm assuming its using the default port. Thanks!

    Read the article

  • How can I remove LibUSB on Windows 7?

    - by Cokegod
    I've installed LibUSB, a software that modifies your USB driver so that programs can access it easily. I didn't know that in Windows 7 you have to run it in compatibility mode for Windows XP, so now my Windows 7 can't access any USB port (including keyboard and mouse). Now I can't access my computer at all, and I don't have any PS2 connection in my computer. I tried to run it in Safe Mode but it didn't change anything. I tried to run a system restore from before the installation of LibUSB, but all the restore points give me an error: "The instruction at 0x73888f18 referenced memory at 0x00000004. The memory could not be read." I also tried to run Hiren's Boot CD and remove all the files associated with LibUSB, but that didn't change anything. So how can I remove LibUSB and access my computer again without formatting my hard drive? (I have important things on it)

    Read the article

< Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >