Search Results

Search found 11826 results on 474 pages for 'parallel port'.

Page 309/474 | < Previous Page | 305 306 307 308 309 310 311 312 313 314 315 316  | Next Page >

• telnet to 3389 connects, RDP remote desktop app bails ?

  - by scott_lotus

  I can TELENT 192.168.10.10 3389 and get a connection. But RDP client to 192.168.10.10 immedietly bails (i.e less then 1 sec) "connect" button greys briefly, RDP app remains on screen. Have tried these from many nodes on the subnet to 192.168.10.10 with same result. On 192.168.10.10 Allow Remote Desktop is enabled. On 192.168.10.10 windows firemall is off. Im connecting from the same subnet i.e no firewall hardware / routers in the way. AV software is installed but other nodes on same subnet allow RDP connection using exact same AV settings (network group profile) Checked 192.168.10.10 for any additonal AV software or local firewall products. Im sure non exist. Checked regedit to ensure 3389 was the port set for listening. Seems to be an XP problem (sp3) ( 2 nodes on the my LAN have this issue) and many work fine. Thanks for any help Scott

  Read the article

• How complex of a daemon should be run through inetd?

  - by amphetamachine

  What is the general rule for which daemons should be started up through inetd? Currently, on my server, sshd, apache and sendmail are set up to run all the time, where simple *NIX services are set up to be started by inetd. I'm the only one who uses ssh on my computer, and break-in attempts aren't a problem because I have it running on a non-standard port, and my HTTP server gets maybe 5 hits a day that aren't GoogleBot. My question is, what are the benefits vs. the performance hits associated with running a complex daemon like sshd or apache through superserver, and what, if any successes or failures have you had running your own daemons in this manner?

  Read the article

• VNC application/terminal server

  - by sebastian nielsen

  Which software should I use, if I want to set up a linux VNC terminal server that works in this way: The VNC server should be able to accept up to X simultanous connections on the same port 5900. The VNC server should use 640x480 on 8 or 16bit color. When the VNC server receives the connection, it should start a new "session" for a user, and auto-launch a specific linux application for that user. If the application is killed, crashes, or is exited in any way, user should be disconnected (kicked) from server. If the user disconnect, the application should be killed in a "graceful way", that allows the application to cleanup. (There should be no way to "pick up" a old session) Any ideas?

  Read the article

• Dell 620 display is too bright to use

  - by keith

  I have a Dell D620 with a display problem. In windows 7 the display seems to be too bright, the text is broken up, the only way to see the mouse is at a very oblique angle. Changing the brightness with fn and brightness control has little/no effect. When I put it in high contrast mode I can see all the colors, but any windows pictures etc are still useless. I cannot get it to connect to an external monitor via VGA port or via a USB-VGA connector.

  Read the article

• How do I run a beanshell script on my Mac?

  - by jonalv

  My Ubuntu-friend told me to testrun a Beanshell script by doing: bsh #filename# and when I told him that I don't know what bsh is nor have it he told me: sudo apt-get install bsh Being on a Mac I instead ran: sudo port install beanshell But still no bsh command available. A listing of the package content revealed a jar file named: /opt/local/share/java/bsh.jar but when I try to run that with my script file a complete Window manager written in Java starts up (and does not run the script file btw). Now, clearly I am doing something wrong, I am sure there must be a way of running beanshell scripts on a mac terminal although it does seem more natural for the linux users. What am I doing wrong and what should I do to run that script?

  Read the article

• usb device in dual mode on gentoo linux

  - by Idlecool

  i am having a flip flop usb modem which has two modes 1 usb mass storage mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fff5 ONDA Communication S.p.A. 2 usbserial mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fffe ONDA Communication S.p.A. by default whenever i plug the modem to the usb port.. the linux machine recognize it as a usb mass storage device.. how can i make it load as usbserial device i have been using a package usb_modeswitch in the past on ubuntu 10.04 but i cannt install the same package on gentoo live cd.. even udev is not installed on live cd.. how to change the product-id of the usb device on gentoo live disc without udev.

  Read the article

• GDM login screen is not displayed with VNC

  - by niboshi

  Hi, I set up VNC server with xinetd. Also configured GDM so that XDMCP is enabled. VNC connection seems okay, but GDM login screen is not shown. Instead I can only see old bare X screen (gray meshed background and X-shaped mouse pointer), which I can't do any interaction with it. What can I do to fix the problem? No log is written below /var/log/. Server distribution: Ubuntu marverick /etc/xinetd.d/vnc is like below: service vnc1024 { disable = no socket_type = stream protocol = tcp wait = no user = nobody server = /usr/bin/Xvnc server_args = -inetd -query localhost -geometry 1024x768 -depth 24 -once securitytypes=none port = 12345 } /etc/gdm/custom.conf: [daemon] [security] DisallowTCP=false [xdmcp] Enable=true [gui] [greeter] [chooser] [debug] [servers] /etc/services is also configured. Thanks

  Read the article

• Lightweight monitoring for a Windows XP laptop

  - by kazanaki

  Hello I have a windows XP laptop in a remote location. I would like to have an overview for CPU/Memory statistics from a remote location. Monitoring a specific service (a Tomcat instance) would be nice but not essential. I have seen the monitoring solutions (Nagios, cacti e.t.c) and they are all very heavy. I do not want to install mysql, web server and other stuff like that on the laptop. I don't even need a web solution at all. It could just be a simple command line app with a server port and on my machine another GUI application would connect there (and not a web browser) Is there something like this available?

  Read the article

• Making internal website available publicly (Win 2008 Server)

  - by endigo

  I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

  Read the article

• Setting Redmine path

  - by David Parunakian

  Hello, How can I set the path on which Redmine should be run, e.g. example.com:3000/redmine instead of example.com:3000? There is an appropriately named option in the settings panel, but it serves a different purpose, according to the documentation and experimental observations (it is used to write URL in emails sent to users). A wider picture: I need this in order to properly serve Redmine on port 80 over Apache's mod_proxy (i.e. at example.com/redmine). The problem is that when running it on /, the home page fails to load the necessary resources (such as JavaScript and CSS files). Any workarounds?

  Read the article

• dell vostro 1310 with nVidia 8400M display problem

  - by Arthur

  Hi everyone, i hope someone can help me with this problem. I have a Dell vostro 1310 Laptop with 32 bit vista and a 8400M nVidia chip. Recently i have noticed performance issues when my girlfriend was playing Sims 3, and then one day i turned it on and all i got was a thick white line at the bottom of the screen. i heard the OS start up so automatically i thought it was a damaged screen, but i had doubts so i plugged it into an external display via the vga port. it worked but everything appart worm the OS choice menu looks distorted beyond belief. even the bios screen had multicoloured lines running down the screen. The resolution is non existant, the screen only shows a 256 colour pallette and is heavily distorted. i barely managed to get to the device manager where i found the gfx card with an exclamation mark. does anybody have suggestions? should i buy a new mobo or are repairs possible? thanks in advance

  Read the article

• Configuring vsftpd with nginx on ubuntu

  - by arby

  I have vsftpd installed on Ubuntu 12.04LTS along with nginx, php, and sql on an Amazon ec2 instance. The web server is good to go, but I'm having trouble connecting to the FTP server. I'm not quite sure how to set the privileges or what configuration options I might be missing. By default, the location of the web root is at /usr/share/nginx/www and it is owned by root:root. The web server runs as user www-data in the group www-data. I've opened port 21 and set the passive ports in the ec2 backend and ufw firewall. In vsftpd.conf, I have: ... anonymous_enable=NO local_enable=YES local_umask=0027 chroot_local_user=YES pasv_enable=YES pas_max_port=12100 pasv_min_port=12000 port_enable=YES ... Now, I'm unsure how to create the FTP user that when I login, displays my web directory with write access. I've tried it a few different ways, but I keep running into errors (either no connection, no write access, or very slow timeouts.)

  Read the article

• How to stop syslog from listening to 514 on CentOS 5.8

  - by Jim

  I have a CentOS 5.8 machine (with regular syslog) that for some reason is listening to port 514, even though it is not started with "-r" (to receive remote syslog messages). # netstat -tulpn | grep 514 udp 0 0 0.0.0.0:514 0.0.0.0:* 2698/syslogd Syslog is started with only "-m 0": ps -ef | grep syslogd root 2698 1 0 15:55 ? 00:00:00 syslogd -m 0 I have tried starting it with "-m 0 -r", just to check if there was any difference, but there is not. This machine is a client and should only log to a central log server - it should not be listening itself. What am I missing?

  Read the article

• My D-Link's Ethernet bridge downlink just got 10-30x slower?

  - by Jay Levitt

  TL;DR: I unplugged my network to move my desk, and now downloading via my DIR-655's Ethernet LAN bridge is 10-30x slower than the Ethernet switch it's plugged into. Background My network is SMC cable modem <-> Cisco firewall <-> Netgear switch <-> D-Link WiFi† | | | | SMC8014 ASA-5505 GS608v2 gigE DIR-655 rev A3 gigE †The DIR-655 is used as an access point, not a router (although what D-Link calls an access point, I'd call a bridge). The "WAN" port is unused; the Netgear connects to the built-in 4-port Ethernet LAN switch, inside the built- in router/firewall. Endpoints: MacBook Pro 17" mid-2010 iPhone 4S Fedora 12 Linux server running reasonably fast dual-Athlon X2, VelociRaptors, etc. All cables are <10 feet, mostly CAT-5e, some CAT-6, all premade. All WiFi endpoints are within three feet of the D-Link. Yesterday I unplugged and rearranged stuff, and now connecting via the D-Link - even through the wired switch, right next to the incoming network cable - is 30x slower than connecting directly to the Netgear switch, on both my MacBook and iPhone. How I'm measuring "slower" I'm mostly using http://speedtest.net, which of course only really measures broadband speeds. I've also installed http://www.speedtest.net/mini.php on my local server, but can't test the iPhone with that. Results Speedtest.net, closest server over Comcast business-class: CONFIG | PING (ms) | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> Netgear | 9 | 31.6 | 6.8 Mac <-> Ethernet <-> D-Link | 8 | 4.1 | 6.0 Mac <-> WiFi <-> D-Link | 9 | 1.4 | 2.9 iPhone <-> WiFi <-> D-Link | 67 | 0.4 | 1.6 Speedtest Mini on Linux PC: CONFIG | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> NetGear | 97.2 | 76.9 Mac <-> Ethernet <-> D-Link | 8.2 | 24.2 Mac <-> WiFi <-> D-Link | 1.0 | 8.6 Slow typing in SSH: Mac <-> Ethernet <-> Netgear <-> Linux PC: smooth Mac <-> Ethernet <-> D-Link <-> Linux PC: choppy Note that D-Link upload speeds are normal on broadband, slower locally (but I'd believe that's a D-Link limitation), and always faster than the downloads! Since ssh is choppy just with slow typing, I don't believe it's a throttling-type problem either; that's not a lot of bandwidth. What I've tried Swapping all "good" and "bad" cables Re-plugging "bad" cable from D-Link to Netgear and watching it be the "good" cable pulling cables away from power lines Verify that the Mac auto-detects the D-Link as gigE Try to verify the link speed of the D-Link <- Netgear connection, but the firmware doesn't report that Verify that the D-Link sees no TX/RX errors or collisions Use different Ethernet ports on both Netgear and D-Link Reset the D-Link to factory settings Upgrade the D-Link firmware from 1.21 to 1.35NA, 2010/11/12, the latest Reboot everything at least once On the Mac, disable Wi-Fi during the Ethernet tests, and unplug Ethernet during the Wi-Fi tests Using iStumbler, verify that the D-Link isn't picking overloaded Wi-Fi channels (usually just 1-5 neighbors on my and adjacent channels, average for my apt building) Verify that the only client connected to the Wi-Fi was the iPhone Verify that nothing was being chatty on my network according to the WISH log Enable and disable all sorts of D-Link settings, including forcing WAN auto-detect to gigE So. I don't mind buying a new access point—I wouldn't mind having a dual-link network—but as a guy who's been networking since gated v4 was a drastic rewrite, and who often used physical sniffers in the days before Wireshark, I'm baffled. I hate being baffled. What could I possibly have changed that would result in this? How can I measure it? All I can think of is a static zap—thick carpet, socks, HVAC—but I didn't feel one, and does that really happen anymore? Can I test if it's Ethernet vs. TCP layer slowness? I'm not familiar with modern network utilities; it's hard to Google without hitting "Q: Why is my network slow? A: Is your microwave on?" If I don't get an answer here, will someone big and powerful help me migrate it to serverfault without getting screamed back here? In the words of Inigo Montoya, "I must know." Don't get all Dread Pirate Roberts on me.

  Read the article

• approx via inetd is not open to connection for others machines

  - by Cédric Girard

  I have an approx server to speed up Debian apt updates, on my Ubuntu 11.04 desktop PC, it had ran fine in the past, but today le 9999 port is open from localhost, but not for others PC. I have not modified inetd configuration at all. What can I check and try? inetd.conf 9999 stream tcp nowait approx /usr/sbin/approx /usr/sbin/approx approx.com # Here are some examples of remote repository mappings. # See http://www.debian.org/mirror/list for mirror sites. debian http://ftp2.fr.debian.org/debian security http://security.debian.org/debian-security volatile http://volatile.debian.org/debian-volatile # The following are the default parameter values, so there is # no need to uncomment them unless you want a different value. # See approx.conf(5) for details. $cache /espace/Dossiers/approx $max_rate unlimited $max_redirects 5 $user approx $group approx $syslog daemon $pdiffs true $offline false $max_wait 10 $verbose false $debug false I tried to allow others PC to connect with a "ALL: ALL" in hosts.allow. ufw is disabled, iptables-save is empty.

  Read the article

• How to Use 3 Monitors

  - by The.Anti.9

  Right now my setup has a nice big 24" flatscreen in the center, and a 19" flatscreen to the left. And a big gaping hole on the right. I have a 3rd monitor to put there, but I'm not sure how to get the computer to recognize it. Do I need a graphics card with 3 ports? Or can I span the monitors over non SLI-Linked graphics cards? Is it possible to plug my 3rd monitor into the on-board VGA port and have it work?

  Read the article

• Apache configuration to accept all data

  - by ServerDown

  Hi, I have apache running on port 7979 to talk with a device that sends data to webserver and later will run php scripts to process and send reply xml. The problem now is that it sends data like POST HTTP/1.1 Content-Type:text/xml Content-Length:369 Followed by XML When apache sees this it gives a 400 error. Since the device cannot be changed is there any way to accept the full data sent from the device and write to some log? Currently apache simply keeps sending 400 errors back. If there was a way to log the entire xml or create some custom handler for 400 error then the xml could be read by a php script. Looking forward to solutions.

  Read the article

• How to Enable Ports 25 - 28 on a Cisco Catalyst 3750

  - by Jared Brown

  I am trying to enable ports 25 - 28 on my 28 port Catalyst 3750. These four ports are my fiber ports. I am using the following command to bring up that interface. interface range Gi1/0/25 - 28 That works and it dumps me in the config-if-interface prompt. This is where I get stuck. I just want to enable these four ports and have them be in VLAN1 and On just like ports 1 - 24. How do I do this?

  Read the article

• How long do managed gigabit ethernet switches take to boot up?

  - by Warren P

  One critical drawback that I have found in researching managed-switches, and one that I have some past experience with is that anything with "lots" of firmware is going to have lots of issues associated with that firmware. We are in the middle of researching rackmount gigabit switches (48 port). It looks like for 48 ports, our only choice is managed switches (Dell, Cisco/Linksys,HP, etc). What I want to know, that I can not find out much about is the boot-time for various managed switches. If you own one, can you please answer with the model number, and the cold boot time in seconds. I have read online that Linksys (now Cisco) SRW series sometimes take almost 5 minutes before they are fully booted up, and that is an unacceptable cost for us. I particularly want to know about Dell PowerConnect managed switch bootup time (model 3548 and 5448), and would like to confirm the 5-minute boot time on the SRW2048 or similar model, and any HP ProCurve boot up times. The composite of all those figures ought to form an interesting overall performance picture.

  Read the article

• Using powershell call native command-line app and capture STDERR

  - by crtracy

  I'm using a port of a cygwin tool on Windows which writes normal status messages to STRERR. This produces ugly output when run from PowerShell: PS> dos2unix.exe -n StartApp.sh StartApp_fixed.sh dos2unix.exe : dos2unix: converting file StartEC3.sh to file StartEC3_fixed.sh in UNIX format ... At line:1 char:13 + dos2unix.exe <<<< -n StartApp.sh StartApp_fixed.sh + CategoryInfo : NotSpecified: (dos2unix: conve...UNIX format ...:String) [], RemoteException + FullyQualifiedErrorId : NativeCommandError Is there a better way? P.S. I intend to post one solution I've found and compare it to answers from others.

  Read the article

• What settings need to be changed to allow EC2 instances to use Amazon's Route 53 for DNS?

  - by ks78

  I have a number of Amazon EC2 instances, all running Ubuntu, which I'd like to configure to use Amazon's Route 53. I setup a script, following Shlomo Swidler's article, but ran into script-related issues, which were answered here. Now, I have the script working, but my instances are still not able to access Route 53's DNS. By this I mean, they are not able to resolve hostnames to IP addresses. My instances are currently configured with the DNS server IP address Amazon pushes out to them by default, does that need to be changed when using Route 53? I'm also IP-restricting my instances using the Security Groups. Could that be the problem? Is there a certain IP address or port I should open to allow communication with Route 53? It seems that DNS requests should be originating from my instances so the Security Groups shouldn't be an issue, but I've been wrong before. If anyone has any ideas, I'd really appreciate it.

  Read the article

• Accessing Windows 7 Printer from Ubuntu Linux via LPR/LPD or Samba

  - by nitbuntu

  Hi, I'm having difficulty printing from my Linux (Ubuntu 10.04) based PC to a printer connected to a Windows 7 machine. I was trying to connect using Samba (version 3.5.6) but this always brings up an authentication screen which never accepts any password I use. So I read somewhere that an alternative is to access the Windows printer via LPR/LPD. I added an LPR/LPD printer in Windows 7, but even within Windows 7, I am not able to print as the print que monitor shows as 'printer busy'. The printer in question is an Epson Stylus DX7400 and works fine when using the standard USB ports....but doesn't when I use with the LPR/LPD ports. I even opened up the TCP/IP port 515 in my McAfee firewall without any success. Any help with this would be highly appreciated. Additionally, does anyone have any idea how I can get Samba working for me?

  Read the article

• Is an Ethernet point to point connection without a switch real time capable?

  - by funksoulbrother

  In automation and control, it is commonly stated that ethernet can't be used as a bus because it is not real time capable due to packet collisions. If important control packets collide, they often can't keep the hard real time conditions needed for control. But what if I have a single point to point connection with Ethernet, no switch in between? To be more precise, I have an FPGA board with a giga-Ethernet port that is connected directly to my control PC. I think the benefits of giga Ethernet over CAN or USB for a p2p connection are huge, especially for high sampling rates and lots of data generation on the FPGA board. Am I correct that with a point to point connection there can't be any packet collisions and therefore a real time environment is given even with ethernet? Thanks in advance! ~fsb

  Read the article

• Testing php mail() in localhost problem

  - by Samir Ghobril

  Hey guys, recently I just installed msmtp in linux and I even send a mail from the terminal and it worked: echo -e "Subject: Test Mail\r\n\r\nThis is a test mail" |msmtp --debug --from=default -t [email protected] But in php, after editing the php.ini file to have this: sendmail_path = '/usr/bin/msmtp -t' and using this piece of code: <?php if ( mail ( '[email protected]', 'Test mail from localhost', 'Working Fine.' ) ){ echo 'Mail sent'; } else{ echo 'Error. Please check error log.'; } ?> I get the Mail sent message but don't receive a message in my inbox. Not even in the spam folder. Anything wrong I'm doing? msmtp configuration file: defaults tls on tls_starttls on tls_trust_file /etc/ssl/certs/ca-certificates.crt account default host smtp.gmail.com port 587 auth on user [email protected] password password from [email protected] logfile /var/log/msmtp.log

  Read the article

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

< Previous Page | 305 306 307 308 309 310 311 312 313 314 315 316  | Next Page >